Housing Urban and Rular Development Government Departments Closing in 6 days TDR #58415962

Tender For Special Repairs To Leaky Roof, Floor Tiles, Toilet Work, Sanitary Arrangements And Painting Works In Government Health Sub Centre At Thenpalanji Village In Madurai District.

Issued by Government Departments · Madurai, Tamil Nadu
Tender Value
9.72 Lakhs
Estimated cost
Bid Submission
23 Nov 2026
6 days left
EMD
9720
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Madurai → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Special Repairs To Leaky Roof, Floor Tiles, Toilet Work, Sanitary Arrangements And Painting Works In Government Health Sub Centre At Thenpalanji Village In Madurai District.

BOQ

Name of Work:- Special repairs to Leaky roof, floor tiles, toilet work, sanitary arrangements and painting works in Government Health Sub Centre at Thenpalanji Village in Madurai District.
Sl. No. Item Description
1Dismantling, clearing away and carefully stacking materials for reuse of the following. Any thickness of :
2Brick/ Stone masonry in cement mortar walls under 3m high
3Dismantling Plain Cement Concrete
4Pressed tiles & weathering course
5Floor finish and dadooing walls in cement mortar with mosaic tiles/ Glazed tiles/ Cuddappah slabs.
6Clean Removal of cement plaster from wall surfaces.
7Earth work excavation for foundation by manual means for RR/Brick and Other step type footings for Load bearing structures in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers.
8Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers. -Mixing by manual means
9Cement Concrete 1:5:10 (One cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers -Mixing by Manual means
10Brick work in following Cement Mortar using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge.
11Foundation & basement
12Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the departmental officers..
13Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.
14Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.- Mixing by manual means
15Paving the floor with best quality Double charged Vitrified Tiles of following size 600x600x8mm and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works).
16Flooring with ceramic tiles of following size 305x305x6mm and variety conforming to IS 15622 laid over cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)
17Dadooing walls with ceramic tiles of size 300mm x450mmx 8mm and above in best approved quality tiles set in Cement Mortar 1:2 (One Cement and Two m sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification (Non branded) and as directed by the departmental officers.
18Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.
19Finishing the top of roof with one course of New machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three M-Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers
20Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)
21Paving the floor with Cement based Hydraulically pressed Anti skid tiles (pattern design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three M- sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)
22Supplying and fixing Mild Steel grills for windows, ventilators etc.,complete complying with standard specifications and as directed by the departmental officers.
23Supplying and fixing 40mm dia GI pipe for staircase hand rail including labour charges for cutting, welding and fixing with MS flats (excluding cost of flat), etc., as directed by the departmental officers
24Supplying and fixing in position steel balustrades using 20mm square rods spaced at 150mm centre to centre so that the two balustrades in each step shall be placed centrally and the top of balustrades connected with the hand rails (cost of hand rail shall be measured and paid separately) by means of MS flats of size 40mm x 6mm in the groove 40mm x 6mm provided at the bottom of hand rail; the bottom of balustrades shall be fixed on to the top of step concrete. An additional MS flat of size 50mm x 6mm shall be provided at the centre of balustrades connecting all square rods to the entire length including cost of square rods, flat and applying one coat of red oxide primer to the iron surfaces, etc., complete complying with standard specification and as directed by the departmental officers.
25Labour wrought and put up in position Shutters for fully panelled doors (external or internal) moulded panels including labour charges for fixing furniture fittings complying with standard drawings and standard specification.
26Supplying and fixing solid core particle board flush shutter of nominal thick of 35 mm with necessary T.W. internal lipping conforming to IS 2302 with both sides alround commercial ply 35mm thick including supplying and fixing cost of wind appliances and furniture fittings such as 1no .200x12mm aluminium tower bolt 2nos. 150x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete as directed by the departmental officers.
27Fabricating, Supplying and fixng in position of steel sheeted windows ( Two Leaves) with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18x5mm MS Flat at 0.70kg/m at 3 Nos. for each shutter and additional diagonal stiffners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in position firmly. 2 numbers of Steel Offset Pivot hingesof size 3\\" and one number of handle-cum-latch of special type made with 18x5mm MS flats are revetted to the shutters at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adustable stay made out of 18 x 5mm at 0.70 kg/ m MS flat of lenght 320mm with three adjustable position. A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 200mm length spliced at the ends are welded to the outer frame of the window by using MS flat of 18x5mm at 0.70kg/m, welded to the shutter at two place equivalent from each from top and bottom of the shutter. An MS square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge between them. All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers.All sections should be in confirmed with IS 7452/1990.The cost includes cost of all materials, labour charges and other incidental charges, etc., complete complying with standard specification and as directed by the departmental officers.
28Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.
29Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed by the departmental officers. 50mm thick
30Supplying, fabricating and placing in position of MILD STEEL or RIBBED TOR STEEL GRILL for all reinforced cement concrete works including cost of steel and G.I. binding wire as directed by the Departmental Officers complete complying with standard specification.
31Supplying and fixing New PVC DOOR with PVC frame made from M.S. box section of size 19mm x 19mm x 19 gauge covered in all sides with moulded PVC Sheet of 5mm thick and restricting the overall size of 50mmx50mm to form styles and rails. The panel shall be 5mm thick PVC rigid steel inserted into the frame and sealed to the styles and rails and 5mm x 2.5mm PVC beading shall be provided in all sides including cost of supplying and fixing the following aluminium anodised furniture fittings and etc. complete. The size of outer frame is 48 x 40mm. 3Nos. 125mm butt hinges, 1 No. 150mm tower bolt of 12mm dia, 1 No. 200mm x 16mm aldrop, 2 Nos. 100mm 'D' type handles.
32Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia \\"B\\" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).
33Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with \\"P\\" or \\"S\\" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).
34Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. - External water supply -Below ground level.
3525mm dia PVC pipe
36Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level
37110mm dia PVC Waste water pipe
38Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works)..
39110mm dia PVC elbow
40Supplying and fixing in position 15mm dia SD tap of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)
41Supplying and fixing New PVC. WATER TANK of approved quality conforming to ISI specification 1000 litre capacity having suitable cover, bolts including cost of tank, taxes, transportation to work spot, fixing in position at place as shown and as directed by the Departmental Officers including conducting required water test complete complying with standard specification.
42Drilling of 6\\" or 150 mm dia vertical bore in hard rock area of any required depth as directed by the departmental Officers including labour charges for inserting casing pipes assembles in the drilled holes excuding cost of PVC casing pipes of required length including transportation charges for Rig supporting vehicles from one place to another place etc.,complete complying with standard specification.
43Upto 150m below ground level
44(From 151m upto 180m)
45Supplying and delivery of 6\\" or 150 mm dia PVC Casing pipe as per IS 12818/1992 with ISI Marking of following diameter in 3m length with screwed and socket end and centering guides for every 15m length of pipe to suit deep bore wells for delivery including loading, unloading, freight, insurance etc., complete (Rate inclusive of Excise duty)
46Labour charges for inserting 160mm dia PVC casing pipe assembly (with or without slots) in the drilled hole including jointing the pipes with PVC couplers with cement paste
47Supplying and fixing of suitable PVC endcap (6kg/cm2)for 6\\"dia borewell of best quality with ISI mark (the PVC endcap should be not approved by the departmental officers before execution)
48Supplying laying and jointing CPVC. pipes best quality conforming to I.S.S. and with I.S.I. mark of following sizes including cutting and fixing with G.I. specials but including cost of such specials and fixing into bore well for suction line, air pipe etc., complete complying with standard specification. 32mm CPVC.pipes
49Supplying and fixing Borewell MS clamp Set , cover with foundation bolt and nut for casing pope etc.,
50Supply of 4.00 sqm, three core flat copper cable for submersible motor with wire bound having good quality with etc., complete complying with standard specification and as directed by the departmental officers.
51Suply and fixing of Nylon rope for bore well and as directed by the departmental officers.
52Supplying, erecting and fixing 2HP submersible motor multi stage in borewell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter voltmeter Ammeter three pilot lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and earthing as per rules etc, complete and testing the pumpset and trail run for 10 days.
53Supplying the panel board of 2HP fully automatic starter D.O.L. with two level guard, 3 phase preventive on and off switch, indicator lamp, voltmeter, ammeter with selected switch with suitable power capacity arrangements in sheet, steel cubical etc., complete as directed by the departmental officers
54Labour charges for erection submersible pump set in bore well including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the end erection of panel board consisting of TPKN switches, starter, voly ;meter, ammeter, three pilot {indicating) etc., complet complying wit standard specification.
55Painting wall surface with Two Coats of PLASTIC INTERIOR EMULSION PAINT of approved quality and colour and cost of all materials, cleaning the surface and filling inequality with gypsum labour charges for painting including thecost of primer complete as directed by the Departmental Officers complete complying with standard specification. The make and colour of paint to be used should be got approved by the departmental officer before use on work.
56Painting wall surface with Two Coats of PLASTIC EXTERIOR EMULSION PAINT of approved quality and colour and cost of all materials, cleaning the surface and filling inequality with gypsum labour charges for painting complete as directed by the Departmental Officers complete complying with standard specification. The make and colour of paint to be used should be got approved by the departmental officer before use on work.
57Art painting work in walls including cost of material, loading and unloading, transportation, labour charges and all other incidental charges etc., complete complying with standard specification
58Painting wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)
59Painting iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)
60GST@ 18% Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58415962
AUTHORITY Government Departments
TENDER VALUE 9.72 Lakhs
LAST DATE 23-11-2026
Authority
Authority Name Public Works Department
Work Description Tender for Special Repairs To Leaky Roof, Floor Tiles, Toilet Work, Sanitary Arrangements And Painting Works In Government Health Sub Centre At Thenpalanji Village In Madurai District.
Basic Detail
Tender No 05/F10 /2026-27(8),Dated 03.11.2026
Bidding Type Tender
Location
City Madurai
State Tamil Nadu
Key Dates
Publish Date 06 Nov 2026
Submission Date 23 Nov 2026
Open Date 23 Nov 2026
Finance
Tender Value 9.72 Lakhs
Tender Fee Ref. Documents
EMD 9720
Exemption Not Available
Document List
BOQ_867205.xls
d75d90e8-cd4c-4197-ab5f-b759eb9a11e8.html
tenderdocument.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 06, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 23, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 6 days
Nov 23, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 6 days

Tender Documents

Download All (ZIP) ↓
xls

BOQ_867205.xls

html

d75d90e8-cd4c-4197-ab5f-b759eb9a11e8.html

pdf

tenderdocument.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender