Tender For Providing Esewa Kendra Porta Cabin 1 No In Sub Court Parking Area Of Combined Court Complex At Coimbatore.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
23 Nov 2026
6 days left
EMD
4300
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Coimbatore → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing Esewa Kendra Porta Cabin 1 No In Sub Court Parking Area Of Combined Court Complex At Coimbatore.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work excavation for foundation by manual means for RR/Brick and Other step type footings for Load bearing structures in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers. |
| 2 | Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 3 | PLAIN CEMENT CONCRETE 1:5:10 (One cement, five M - sand and ten aggregate) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 4 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener , side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid). |
| 5 | PLAIN CEMENT CONCRETE 1:2:4 (One cement, two M - sand and four aggregate) using 20 mm gauge hand broken hard granite stone jelly for WEARING COAT including dewatering if found necessary and laid in layers of not more than 15cm thick, well rammed etc., complete complying with standard specification. |
| 6 | Fabricating Supplying and fixing in position of Porta Cabin of overall size 15’X10’x8’6” with the following specifications:- The Main fabrication of the structural frame work shall be integral (welded) to comprise of the bottom frame ISI Standard C-Channel 100X50-6mm Thickness and Stiffener Bottom ISI Standard C-Channel 100X50-6mm with Stiffener MS Pipe 100X50, 80X40 & 60X40-2mm thick and Top Frame MS SQ Pipe 50X50-1.4mm & 50X25-1.4mm thickness Stiffener Top MS SQ Pipe 50X50-1.4mm, 50X25-1.4mm & 25X25-1.4mm Thickness. Side Post & Side Wall Stiffeners Corners shall be of MS L-Angle 65X65-6mm ISI Standard with wall thickness of 50mm. Paneling Outside & Roof Top Specially formed M.S. CR Corrugated Sheet -1.2mm Thick & MS CR-Sheet 1.2mm thick properly Sloped Plain surface with full welding all-round to Roof and Internal Wall Paneling The paneling of side wall & Roof shall be of MDF board 7.8mm & all vertically and horizontal corners shall be neatly and smoothly finished with Aluminum section and Bottom Flooring 18mm cemented fiber board with 100% water, Fire & Termite Resistance. & on Top of it Vinyl Carpet of 1mm Thickness and Aluminum Sliding Windows Double Shutter sliding Aluminum, Powder coated Windows with 4mm Glass for all windows. Safety grills from outside and monsoon shed on top of the windows. (3-tier Mesh) and Main Door MS Frame of 25X25-1.4mm & 20X20-1.4mm Thickness with same MS corrugated sheet on the outside and 4mm ACP/APP sheet on the inside. Door with standard hardware locks & Handles. Insulation Glass Wool Insulation 50mm thick 32 density on sides and top roof. Wiring All wiring shall be concealed type & shall be insulated copper wire (FR grade) of ISI Polycab Make or Finolex.and Outside Painting Complete painting done with 1 coats of primer/Colour Paint – Make GEM/ASIAN. Hooks and Specially formed hooks for easy lifting and shifting etc... complete complying with standard specification and as directed by the departmental officers |
| 7 | Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition.. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use. |
| 8 | Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 1 No., aluminium tower bolt 200x12mm - 1No., aluminium With FLOOR SPRING and Hinges - 1No ., lock-1No., Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge. |
| 9 | Providing wooden computer work station using anti-termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed and providing keyboard drawer tray with telescopic runners, CPU shelf and cupboard with shutter arrangements along with furniture fittings such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work. |
| 10 | Supply of Computer chair made of Synthetic fabric mesh back & 50mm thick moulded PU foam for upholstered fabric seat, along with hardened PVC handle mounted on mechanized gas lift, supported to Powder Coated CR Steel revolving leg base with 5 leafed twin wheel castor. The rate is inclusive of cost of all materials, labour charges, loading, transportation charges to site of work and unloading etc., Complete complying with standard specification. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysNov 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender