Tender For Addition/Alteration Of House No.1,Type-6,Sector-7 Chandigarh.
Tender Value
24.95 Lakhs
Estimated cost
Bid Submission
12 Nov 2026
4 days left
EMD
49904
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration Of House No.1,Type-6,Sector-7 Chandigarh.
BOQ
| Sl. No. | Item Description |
| 1 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar |
| 2 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below |
| 3 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement :4 coarse sand) |
| 4 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) |
| 5 | Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): Flush / Ruled/ Struck or weathered pointing |
| 6 | Dismantling of ceramic tiles and plaster to making the surface clean for refixing the glazed tiles including removing of malba complete in all respect and to the entire satisfaction of the Engineer in charge. |
| 7 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. Thetiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mm |
| 8 | Providing and laying vitrified floor tiles of size 600 x 600 mm single charge (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade. The tiles are to be fixed with 3mm grove using spacers. The tiles are to be laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm The grove are to be filled with cementitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material. Single charge vitrified tile of size 600x600 mm |
| 9 | Providing and laying antiskid ceramic floor tiles of specified size (thickness to be specified by the manufacturer) of 1st quality with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 mm. |
| 10 | Providing and laying 1st quality ceramic glazed wall tiles of size 300x450 mm conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make, in all colours, shades as approved by Engineer-in-Charge,in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand). The tiles are to be fixed by provding 2 mm thick spacer. The area of spacer is to be filled by using cement based grout of approved shade. The grooves are to be filled with cemenitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material complete in all respect and to entire statisfaction of Engineer-in-Charge. |
| 11 | Providing and fixing 15 to 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. (GRANITE). |
| 12 | Providing and fixing 2nd class teak wood (kiln seasoned) chowkhat 4 1/2\\" x 2 1/4\\"including cost of corner straps, iron hold fasts, hinges, screws,nails, fevicol etc. and spirit polish of chowkhats. Rate includes the cost of dismantling of all damaged chowkhats and making good the damage to walls plaster and floors as required including, disposal of rubbish to the dumping ground the rate further includes the cost of two coats Spirit polish complete in all respect and to the entire satisfaction of Engineer-in-Charge |
| 13 | Providing and Fixing 35mm thick second class teak wood (kiln seasoned) panel door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail wire mesh 22 x 12 mm gauge fixed with 1/2” x 3/4” teak wood (kiln seasoned) beading, with necessary 4 Nos. of hinges, SS Tower bolts, SS Handles 5”, SS sliding bolt and complete fixed in position complete in all respect to the entire satisfaction of Engineer-in-Charge. |
| 14 | Providing and fixing 35mm thick second class teak wood (kiln seasoned) wire guage window shutters consisting of vertical and horizontal styles 75x35mm size with wire mesh 22 x 12 mm gauge fixed with 1/2\\"x3/4\\" wood (kiln seasoned) beading. The rate further includes the cost of 3\\" butt hinges SS tower bolts 4\\", SS handles 2 nos. I-hook and two coats of french polish complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 15 | Providing and fixing 35mm thick 2nd class teak wood (kiln seasoned) glazed window shutters consisting of vertical and horizontal styles 75x35mm size with 4mm thick floated glass pane fixed with 1/2\\"x3/4\\" teak wood (kiln seasoned) beading. The rate further includes the cost of 3\\" butt hinges, S.S. Tower bolts 4\\", S.S. handles 2 nos. I-hook and two coats of Spirit Polish after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 16 | Providing and Fixing 35mm thick 2nd class teak wood (kiln seasoned) wire gauge door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail wire mesh 22 x 12 mm gauge fixed with 1/2” x 3/4” teak wood (kiln seasoned) beading, incluuding Stainless Steel fittings and french spirit polish, complete fixed in position and in all respect to the entire satisfaction of Engineer-in- Charge. |
| 17 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 18 | Providing and fixing 6mm thick polycarbonate multi wall sheet to be fixed on existing M.S. frame with Aluminum rivets complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 19 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 20 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. n gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 21 | Providing and fixing 2'-0” deep cupboard /cabinet consisting of 19mm thick commercial board and 6mm thick ply on back side, 4mm thick teak ply pasted on the exposed surface and making shelves in cabinet 0.8mm mica inside canbinet . The rate further includes the cost of lipping, piano hinges, cupboard lock, screws, nails, 2 nos. fancy s.s. handles, 2 nos. magnetic catchers, fevicol and painting two coats over one priming coat and preparation of surface on board and ply surface and spirit polishing on teak ply complete in position as per entire satisfaction of Engineer-in-charge. |
| 22 | Providing and fixing wooden cabinet of 13½” deep and 2’-0\\" height with open able shutter at wall above 4’-9\\" height consisting of 19mm thick with commercial board (ISI marked) lipped with teak wood lipping of 19mm x 6mm on exposed edges include cost of nail, screws, auto hinges, synthetic adhesive etc. The front shutter and sides are to be furnished with 1mm thick ISI marked superior quality mica of approved shade and inner side of the cabinet with 0.8mm thick mica of approved shade fixed in position with help of wooden gutties at wall complete in al respect to the entire satisfaction of Engineer in charge. |
| 23 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 24 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. |
| 25 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 26 | Reinforced cement concrete work in beams, suspended floors, roofs havingslope upto 15° landings, balconies, shelves, chanas, lintels, bands, plain window sills, staircases and spiralstair cases above plinth level up to floor five level, excludingthe cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 27 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-5000 or more. |
| 28 | Providing and laying in situ five course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd layer of roofing membrane APP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). |
| 29 | 10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: With common burnt clay F.P.S.(non modular) brick tile of class designation 10 |
| 30 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1cement : 3 fine sand) as per standard design :In 75x75 mm deep chase |
| 31 | Making khurras 45x45 cmwith average minimum thickness of 5 cmcement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 32 | P/F 110mm internal dia PVC pipe as rain water pipe on walls of 6 kg. pressure with Bend, Elbow and Clamps complete in all respect to the entire satisfaction of Engineer-- in-Charge |
| 33 | Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat: With common burnt clay F.P.S. (non modular) brick tiles of class designation 10 |
| 34 | Providing and fixing of kitchen cabinet below working shelves made out with 19mm thick commercial ISI marked plyboard and front portion of the cabinet furnished with 1mm thick superior quality sun mica of outer side and 0.8mm thick sun mica inner side of the cabinet for fixing the kitchen accessories and jack at bottom synthetic enamel paint over remaining portion. It is also include the cost of sprit polishing on the edge of the lipping cost of stainless steel handle, adhesive, nail, screws etc. complete fixed in position to the entire satisfaction of Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysNov 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender