Tender For Special Repair Of Bldg No M-3 (Single Offr Accn) At Alhilal Mil Stn Under Ge Palampur
Tender Value
Ref. Documents
Estimated cost
Bid Submission
26 Nov 2026
8 days left
EMD
81000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair Of Bldg No M-3 (Single Offr Accn) At Alhilal Mil Stn Under Ge Palampur
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) n exc. 1.50 Sqm each incl taking out hold fast complete all as specified and as directed. |
| 2 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) exc. 1.50 Sqm but n exc. 4 Sqm each complete all as specified and as directed. |
| 3 | S&F pressed steel frames made out of MS sheet 1.25 mm thick of size 105mm x 60mm for doors with one or more rebates including necessary fixing lung, hinges, lock strike plate etc. complete all as specified and as directed. |
| 4 | S&F pressed steel frames for door made out of MS Sheet 1.25mm thick of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and as directed. |
| 5 | M&L for Plain cement concrete 1:2:4 (Nominal mix), type B-0 (Using 12.5 mm graded crushed stone aggregates) as in filling of steel chowkats or frames, cills and hold fast etc. complete all as specified and as directed. |
| 6 | S&F 35 mm thick wooden flush shutters, solid core construction with block board and 9 mm plywood face panels, commercial type on both sides, complete all as specified and directed. |
| 7 | S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters open rebate and prepared to receive glass/ wire gauge etc (without sas bars)edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) all as specified. |
| 8 | S&F Stainless steel wire netting 0.56mm of nominal dia of each wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed. |
| 9 | M&L for preparation of wooden surfaces of any description exc over 10cm with or grith and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 10 | S&F Solid PVC door frame of size 50x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, S&F Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheet to be fitted in the MS frame welded / sealed to in stiles & rails with suitable PVC sheet beading and joined together with solvent cement S&F in frames at site as per specification and drawing shown in SSR Part-II, complete all as specified and directed. |
| 11 | S&F Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheet to be fitted in the MS frame welded / sealed to in stiles & rails with suitable PVC sheet beading and joined together with solvent cement S&F in frames at site as per specification and drawing shown in SSR Part-II, complete all as specified and directed. |
| 12 | M&L for Anodised powder coated aluminium frame for doors, windows, ventilators with one or more rebates, including joing cleats for fixing etc complete all as specified and directed. |
| 13 | S & F Anodised aluminium window and ventilator shutters, side hung type without sash bars,, (powder coating of any colour and thickness not less than 50 micron) aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. |
| 14 | S & F Anodised aluminium three parallel tracks within the frame, allowing for three sliding panels for window and ventilator (two panels fixed with ordinary quality glass of thickness 4.8 mm and one panel fixed stainless steel wire cloth 0.56 mm of nominal dia of each wire and average width of aperture 1.18 mm) (powder coating of any colour and thickness not less than 50 micron) aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as multi point lock, glass sealant etc, complete all as specified and as directed.Note:- The rate includes Three track frame, Three No panels(2 glass and 1 wire cloth including 5 mm thick glass and wire cloth as described in item description) |
| 15 | M&L for Sheet glass,3.0 mm thick ordinary quality and glazing with putty or fix in neoprene rubber in aluminium section any size in square exc 0.5 sqm in each pane complete all as spfd and as directed |
| 16 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed. |
| 17 | S&F in repair stainless steel (ss304 grade) curtain rod including brackets with cut hole suitable for 20 mm dia rod fixed with screws and gutties in wall, including end caps with wall ornament and fixed to curtain rod with screws of design/shape complete all as specified and directed. |
| 18 | M&L for Preparing the new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over priming the surface with red oxide complete all as specified and directed |
| 19 | S&F butt hinges 100mm, cold rolled medium weight mild steel complete all as specified and directed. |
| 20 | S&F 125mm size, extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 21 | S&F 150mm long aluminium tower bolts (ISI Marked) extruded type all as specified complete all as specified and directed. |
| 22 | S&F 250 mm size Aluminium alloy sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed |
| 23 | Demolition of brick work or stone /boulder masonry, built in CM, incl all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc, complete all as specified and directed. |
| 24 | M&L for Brickwork with old size sub class 'B' bricks, straight or curved on plan exc 6m radius, built in cm (1:6) complete all as specified and directed |
| 25 | Supply only liquid water proofing compound. |
| 26 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing debris outside the premises complete all as specified and directed |
| 27 | M&L for 75 mm thick cement concrete type C-2, 1:3:6 (40mm graded aggregate) casted in panels as in plinth protection complete all as specified and directed. |
| 28 | M&L for forming 6 mm wide joint in plinth protection and filled with mastic filling comprising of one part of heated bitumen Vg-30 grade and 3 parts of sand (all by weight), complete all as specified and directed. |
| 29 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick in CM 1:6 including dismantling of floor tiling incl cement mortar bedding (but not backing) removing serviceable tiles to a store and rubbish off premises, complete all as specified and directed. |
| 30 | M&L for Vitrified Ceramic tiles dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exc 0.36 sqm, but not exc. 42 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screwed bed in cement mortar 1:6 including Dismantling of floor tiling incl cement mortar bedding (but not backing) removing serviceable tiles to a store and rubbish off premises, complete all as specified and as directed. |
| 31 | All as per above Item No 30 except in walls such as skirting, complete all as specified and directed. |
| 32 | M&L for Glazed ceramic coloured tiles of size 450 x 300 x 7mm thick, on vertical surfaces of walls such as skirting dado etc, set and jointed in neat cement slurry and pointed in white or colour cement to match including dismantling of wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to a store and rubbish off premises, all as specified and directed. |
| 33 | Taking down cement plaster of any description and any thickness on brick/stone/concrete surfaces scrubbing down with water etc complete all as specified and directed. |
| 34 | M&L for Rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finishing the surface even and smooth without using extra cement including taking down cement plaster on brick or concrete surface complete all as specified and directed. |
| 35 | M & L for Rendering 15 mm thick in two coats i.e. 10mm thick in CM 1:6 and 5mm thick in CM 1:4 using water proofing liquid compound as per manufacturer's instructions on other than fair faces brick or concrete surfaces and finishing surfaces even & smooth without using extra cement. complete all as specified and directed. Note :- Water proofing liquid compound shall be measured and paid separately. |
| 36 | M&L for Distempering with 1st quality acrylic distemper (ready mixed ) having VOC content less than 50 gm/litre of approved manufacturer of required shade and colour complete as per manufacturers specification two or more coats over a coat of primer over and including 2 mm thick wall care putty on new plastered surface of wall including preparation of surfaces with complete all as specified and directed. |
| 37 | M&L for Distempering with 1st quality acrylic distemper (ready mixed ) having VOC content less than 50 gm/litre of approved manufacturer of required shade and colour complete as per manufacturers specification two or more coats over 2 mm thick wall care putty on old surface of wall including preparation of surfaces by complete removal of existing treatment , complete all as specified and directed |
| 38 | M & L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive excellent dirt pickup resistance with low VOC less than 50, Antifungal/ Anti Alkali properties in two coats not less than 1.79 litre(undiluted)/10 Sqm diluted with water as per manufacturer's instruction applied over primed surface with fully automatic airless spray machine of point application with a flow speed of minimum 1 litre per minute having a pressure of 3300PSI. Allow 6-8 hrs to dry the surface in between subsequent coats of paint over a coat of acrylic water based exterior grade primer @ 0.90 litre(undiluted)/ 10 sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine and allow 6-8 hours to dry the surface including water proof cement based putty @1kg (undiluted) per sqm of average thickness 2mm over the new plastered painted surface of wall and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 grit or above to make the surface :- Step 1: Mix the putty powder by adding water as manufacturer's instruction and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2: Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine/ manually of putty application finishing the surface even and smooth in level without any undulations. Step 3: Allow 6-8 hrs time to dry the putty surface. |
| 39 | S&F Steel water tubing, 15mm bore dia, galvanised, \\"medium grade\\" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc including taking down & cleaning for refixing or removal to store, complete all as specified and directed. |
| 40 | S&F Steel water tubing, 20mm bore dia, galvanised, \\"medium grade\\" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc including taking down & cleaning for refixing or removal to store, complete all as specified and directed. |
| 41 | S&F in repair 20 mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 42 | S&F in repair Vitreous China wash down water closet pan and trap, (pedestal pattern) (Fixing includes bolts, 'P' and 'S' trap and connecting to drain pipe, white seat cover plastic flat bottom and MS Chromium plated hinging device and connection to flush pipe, flushing cistern and also polyethelene flushing pipe) etc complete all as specified and directed. |
| 43 | S&F in repair of PVC 10 Ltr valveless,syphonic action type, flushing cistern, low level,white inlet, ball valve, float and handle including bracket and & supply of flush pipe of polyethylene of low or high density or PVC, 32 mm dia for low level cistern device complete all as specified and directed. |
| 44 | S&F in repair vitreous china wash hand basin white, flat back of bowl size 550x400mm including waste coupling and waste pipe PVC 32 mm dia to be fixed over mild steel bracket including pinning in ends of brackets and including fitting with pedestal, complete all as specified and directed. |
| 45 | S & F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in pipe, complete all as specified and directed. |
| 46 | S&F in repair 15mm bore one way Angle valves, CP fancy type chromium plated screwed both ends for iron pipe or for unions, high pressure with crutch or butterfly handle, screwed both ends (externally threaded) complete all as specified and directed. |
| 47 | S&F in repair 15mm bore two way Angle valves, CP fancy type chromium plated screwed both ends for iron pipe or for unions, high pressure with crutch or butterfly handle, screwed both ends (externally threaded) complete all as specified and directed. |
| 48 | S&F in repair wall mounted Brass chromium plated mixture for mixing hot and cold water, screwed down for iron pipe for 15mm dia bore pipe, complete all as specified and as directed. |
| 49 | S&F in repair CP Pillar taps fancy type 15 mm bore cast alloy with capastan head screwed down high pressure with without lettered Hot or Cold with long screwed shanks and fly-nutscrewed complete all as specified and directed. |
| 50 | S&F in repair bib taps 15mm bore, fancy type chromium plated with butterfly handle, screwed down, high pressure, with carutch or butterfly handle, screwed both ends for iron pipe or for unions, including wall flange complete all as specified and directed. |
| 51 | Supply & Fixing in repair 600mmx450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete including dismantling old mirror complete all as specified and directed. |
| 52 | S&F in repair brass chromium plated tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges including taking down old towel rail/rod, complete all as specified and directed. |
| 53 | S&F in repair Liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats, (Minimum weight 105 gms) complete all as specified and directed. |
| 54 | S&F in repair PVC connections 15mm, 450mm long with PTMT nuts washers etc complete all as specified and directed. |
| 55 | S&F Rotational moulded polyethylene water storage tank 1000 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position with PVC float ball valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, complete all as specified and directed. |
| 56 | Dismantling of CI/PVC pipe 75 mm bore fixed to wall or laid in floor or trenches inculding connection all as specified and directed. |
| 57 | Dismantling of CI/PVC pipe 110 mm bore fixed to wall or laid in floor or trenches inculding connection all as specified and directed. |
| 58 | S&F PVC (SWR) pipes 75 mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed. |
| 59 | S&F PVC (SWR) pipes 110 mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed. |
| 60 | S & F 75 mm bore PVC Bends (SWR) with access door, complete all as specified and directed. |
| 61 | S & F 75 mm bore PVC (SWR) T-Junction, complete all as specified and directed. |
| 62 | S & F 110 mm bore PVC Bends (SWR) with access door, complete all as specified and directed. |
| 63 | S&F in repair PVC (SWR) Nahani/floor trap of 75 mm dia with CP Grating including jointing with Solvent cement complete all as specified and directed. |
| 64 | S&F PVC (SWR) vent cowl 110 mm dia, complete all as specified and directed. |
| 65 | S&F in repair stainless steel sink, 1.00 mm thick for kitchen or laboratory, with plug waste pipe, washers, including cantilever cast iron brackets, connecting union etc, overall size 495 mm x 420 mm with bowl size 410 mm x 330 mmx160 mm, complete all as specified and directed. |
| 66 | Dismantling of wall & ceiling boards (fiber pulp insulation etc) or insulation boards/slabs/blankets of any thickness, including cover fillets complete all as specified and directed. |
| 67 | S&F clip-in false ceiling system with plain steel beveled edged tile (600mmx600mm) manufactured out of 0.70mm aluminium sheet having power coating with 60 microns polyester paint on front side. Two sides of each tile shall be rised and piped and stopped to ensure positive engagement into the spring clip-in profile allowing for demounting of individual tiles. The rigid suspension system consists of rows of galvanized steel 0.50mm thick clip-in profile of size 38mm x 20mm and piped and stopped to ensure positive engagement into the spring clip-in profiles shall be suspended and jointed from galvanized steel 'C' channels of size 10mm x 38mm x 10mm with hold on clamps at spacing as specified by manufacturer. Suspension angles shall be suspended from the roof structure by GI ceiling brackets as per manufacturer's instructions and jointed to the 'C' channels. The tiles shall be held in place by pressure clips 'C' at spacing as per manufacturer's instructions. GI wall angle shall be used on wall angle shall be used on wall of size 20mm x 30mm x 20mm and 0.5mm thick with width matching the colour with tiles all as manufacturer's specification/instructions and including necessary scaffolding all as specified and directed. |
| 68 | M & L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper bedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, inishing and sweeping extra sand, complete all as specified. |
| 69 | M&L for 75 mm Thick PCC 1:4:8 Type D-2 using 40 mm graded crushed stone aggregate as in sub base complete all as specified and as directed. |
| 70 | M&L for plain cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in coping, finished fair and even including necessary formwork complete all as specified and directed |
| 71 | M&L for Non skid ceramic coloured parking tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 including dismantling of floor tiling incl cement mortar bedding (but not backing) removing serviceable tiles to a store and rubbish off premises complete all as specified and directed. |
| 72 | M&L for Cement concrete type C-2 1:3:6 using 40 mm graded crushed stone aggregate in surface channels and drains etc including necessary formwork complete all as specified and directed. |
| 73 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends complete all as specified and directed. |
| 74 | M&L for precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded crushed stones aggregate as in cover slabs, shelves and other similar work set in CM 1:6 complete all as specified and directed. |
| 75 | All as per item no 74 in fillets, rails, posts, rafters, purlins, etc under 40 sq, cm in section, any position in unframed work. |
| 76 | Dismantling posts or struts(wood steel or RCC) any section, including taking out embedded portion embedded in concrete, brick work, masonry etc and making good disturbed ground, complete all as specified and directed. |
| 77 | S&F, Rolled Mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (beam, tee, angle, channel, tubular or flat sections) including distance pieces, cleats etc confirming to Fe 410 (gde E-250) quality 'A', complete all as specified and directed. |
| 78 | S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of grade Fe-410 (Gde E-250) quality 'A', complete all as specified and directed. |
| 79 | S&F for Mild steel rag or lewis bolts, Diameter of neck 20mm, screwed one end, with hexagonal or square nuts and washers, tje other end enlarged and jagged or kevissed Isngth of bolt exc 15cm and n exc 30cm long complete all as specified and directed. |
| 80 | Dismantling of plain or corrugated steel sheeting,any gauge,thickness,including nanital or similar pattern roof covering, S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws. Sheet colour approved by Engineer-in-Charge complete all as specified and directed. |
| 81 | Dismantling of plain or corrugated steel sheeting,any gauge,thickness,including nanital or similar pattern roof covering, S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 82 | Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, also splays between floors and beams flat for finished surfaces of concrete, complete all as specified and directed. |
| 83 | M&L for RCC M-20 nominal mix (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 84 | M & L for TMT bar 10 mm and over cut to length, bend to shape required including cranking, bending spirally for hoopings for cols, hooking ends and binding with ad including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 85 | M & L for TMT bars 5mm dia and over upto and including 10mm dia as in stirrups cut to length bent to shape required including cranking bending spirally for hooping end and binding with and incl mild steel wiere (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 86 | S&F in repair (incl taking down old ) PVC wall panelling hollow type minimum 5mm thick, printed PVC sheet used instead of plain coloured sheet inclusive of solvent cement/screws/nails, fillets for edges/corner and fixing at site on wall or on PVC frames where required as per specifications and drgs complete all as specified and as directed. |
| 87 | S & F 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including 3 mm thick teak wood lapping on edge complete all as specified and directed. |
| 88 | S&F 2nd class HW plain fillets, square / rectangular, wrought face of sectional area exc 13 & n.exc 25 Sqcm, securing with screw complete all as specified and directed. |
| 89 | M&L for 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished, complete all as specified and directed. |
| 90 | S & F 30mm Continuous (piano) hinges, mild steel, bright finish or elec- trogalvanised, complete all as specified and directed. |
| 91 | M & L for Form work Rough finish to soffits and sides of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) complete all as spfd and directed. |
| 92 | M&L for cement concrete, type B-0 1:2:4 (using 12.5mm crushed stone agg) as in slab supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves with includind form work and the like, complete all as spfd and directed. Note :- Reinforcement if used shall be measured and paid separately under relevant item. |
| 93 | M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 94 | Writing letters or figures (Block, Roman, Italic or Indian) n exc 30 cm high,painted with thick paint, so that they stand out boldly and solidly without showing signs of brush marks, complete all as specified and directed. |
| 95 | S & F Framed work as in framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and directed. |
| 96 | Supply, laying and testing cable XLPE insulated screend PVC bedded, galvanised steel strip or wire armoured electric power cables (Heavy duty) 1100 V grade with stranded aluminium conductor of size 16 sqmm x 4 Core. laid in trenches or passing through pipe all as specified and directed by Engr-In-Charge |
| 97 | Exacavation in trenches not exceeding 1.5 m width and not exceeding 1.5 m depth and getting out for laying of pipe etc in any type of soil complete all as specified and directed |
| 98 | Returning, filling of excavated soil, including spreading levelling, watering and well ramming in layers, not exceeding 25 cm in soft/loose soil complete all as specified and directed. |
| 99 | Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the strating point in soft/loose soil complete all as specified and directed |
| 100 | Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete all as specified and as directed. |
| 101 | Brick, old size sub class 'B' laid in trenches with width wise along the alignment of the cable as protection complete all as specified and as directed. |
| 102 | S&F tube light grade galvanised with all fitting laid in trenches, fixed to wall and floor of 40 mm dia for cable protection complete all as specified and directed. |
| 103 | Taking down carefully existing aluminum / copper point wiring, light fan socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, fan regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades, light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed |
| 104 | Taking down un-serviceable DB of any size and match with existing surfaces complete all as specified and directed keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed |
| 105 | Taking down un-serviceable sub main wiring of any type and any size from wall, ceiling etc complete all as specified and directed Please Enable Macros to View BoQ information |
| 106 | Taking down un-serviceable sub main wiring of any type and any size from wall, ceiling etc complete all as specified and directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender