Tender For Providing Of Certain Sanction Works At Alhilal Mil Stn Under Ge Palampur
Tender Value
Ref. Documents
Estimated cost
Bid Submission
26 Nov 2026
8 days left
EMD
69000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Providing Of Certain Sanction Works At Alhilal Mil Stn Under Ge Palampur
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) n exc. 1.50 Sqm each incl taking out hold fast complete all as specified and directed. |
| 2 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) exc. 1.50 Sqm but n exc. 4 Sqm each complete all as specified and directed. |
| 3 | S&F pressed steel frames made out of MS sheet 1.25 mm thick of size 105mm x 60mm for doors with one or more rebates including necessary fixing lung, hings, lock strike plate etc. complete all as specified and directed. |
| 4 | M&L for Plain cement concrete 1:2:4 (Nominal mix), type B-0 (Using12.5 mm graded crushed stone aggregates) as in filling of steel chowkats or frames, cills and hold fast etc.complete all as specified and directed |
| 5 | S&F 35 mm thick wooden flush shutters, solid core construction with block board and 9 mm plywood face panels, commercial type on both sides, complete all as specified and directed. |
| 6 | S&F Stainless steel wire netting 0.56mm of nominal dia of each wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed. |
| 7 | S&F Solid PVC door frame of size 50x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, S&F in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed |
| 8 | S&F Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to in stiles & rails with suitable PVC sheet beading and joined together with solvent cement S&F in frames at site as per specification and drawing shown in SSR Part-II, complete all as specified and directed. |
| 9 | Taking down exiting aluminium door and refixing the door in the same opening after bluiding repair work complete all as specified and directed |
| 10 | M&L Anodised powder coated aluminium frame for doors, windows, ventilators with one or more rebates, including joing cleats for fixing etc complete all as specified and directed. |
| 11 | S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, (powder coating of any colour and thickness not less than 50 micron) aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. |
| 12 | S&F Anodised aluminium three parallel tracks within the frame, allowing for three sliding panels for window and ventilator (two panels fixed with ordinary quality glass of thickness 4.8 mm and one panel fixed stainless steel wire cloth 0.56 mm of nominal dia of each wire and average width of aperture 1.18 mm) (powder coating of any colour and thickness not less than 50 micron) aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as multi point lock,glass sealant etc,.complete all as specified and directed. Note:- The rate includes Three track frame, Three No panels(2 glass and 1 wire cloth including 5 mm thick glass and wire cloth as described in item description) |
| 13 | M&L for Sheet glass,4.8 mm thick ordinary quality and glazing with oil putty or fix in neoprene rubber in aluminium section any size in square exc 0.5 sqm in each pane complete all as specified and directed. |
| 14 | M&L for Providing, fabricating and fixing Stainless Steel Window Grill of approved design made out of SS 304 Grade mirror/matte finish stainless steel square pipes comprising outer frame of 25 mm x 25 mm x 1.6 mm thick and vertical/horizontal members of 12 mm x 12 mm x 1.2 mm thick square pipes @ spacing of 100 mm C/C or as approved, welded with TIG welding, joints ground smooth, complete with SS brackets, SS expansion fasteners, necessary holdfasts, cutting, welding, grinding, polishing, fitting and fixing to masonry/RCC surface including all labour, T&P, scaffolding, carriage, wastage and all incidental charges complete all as specified and directed. |
| 15 | S&F in repair mild steel chromium plated curtain rod including brackets with cut hole suitable for 20 mm dia rod fixed with screws and gutties in wall, including end cap with wall ornament and fixed to curtain rod with screws of design/shape complete all as specified and directed. |
| 16 | M&L for Preparing the new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over priming the surface with red oxide complete all as specified and directed. |
| 17 | S&F butt hinges 100mm, cold rolled medium weight mild steel complete all as specified and directed. |
| 18 | S&F 125mm size, extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 19 | S&F 150mm long aluminium tower bolts (ISI Marked) extruded type all as specified complete all as specified and directed. |
| 20 | S&F 250 mm size Aluminium alloy sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed. |
| 21 | Demolition of brick work or stone /boulder masonry, built in CM, incl all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc, complete all as specified and directed. |
| 22 | M&L for Brickwork with old size sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cm (1:6) complete all as specified and directed. |
| 23 | M&L for Brickwork with old size sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cm (1:4) as in masonry manholes, complete all as specified and directed. |
| 24 | M&L for Cutting out concrete blocks, slabs, brickwork or stone masonry (in alter nate course), forming tooth-ings for and bonding new work in mortar into oldwork, including new materials entering old wall except block or slabs set in cement mortar 1:4 complete all as specified and directed. |
| 25 | Supply only liquid water proofing compound. |
| 26 | Demolition of cement concrete ( unreinforced) of any description and in any position not otherwise specifically provided for and removing debries outside the premises complete all as specified and directed. |
| 27 | M&L for 75 mm thick Cement concrete type C- 2, 1:3:6 (40mm graded aggregate) casted in panels as in plinth protection complete all as specified and directed. |
| 28 | M&L for forming 6 mm wide joint in plinth protection and filled with mastic filling comprising of one part of heated bitumen Vg-30 grade and 3 parts of sand (all by weight), complete all as specified and directed. |
| 29 | M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick in CM 1:6 including dismantling of floor tling incl cement mortar bedding (but not backing) removing servicable tiles to a store and rubbish off premises, complete all as specified and directed. |
| 30 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick in CM 1:6 including dismantling of floor tling incl cement mortar bedding (but not backing) removing servicable tiles to a store and rubbish off premises complete all as specified and directed. |
| 31 | All as per item no 30 above except in walls over neat cement slurry, complete all as specified and directed. |
| 32 | M&L for Glazed ceramic coloured tiles of size 450 x 300 x 7mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including dismantling of wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to a store and rubbish off premises . complete all as specified and directed. |
| 33 | Taking down cement plaster of any description and any thickness on brick/stone/concrete surfaces scrubbing down with water etc complete all as specified and directed. |
| 34 | M&L for Rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finishing the surface even and smooth without using extra cement including taking down cement plaster on brick or concrete surface complete all as specified and directed. |
| 35 | M & L for Rendering 15 mm thick in two coats i.e. 10mm thick in CM 1:6 and 5mm thick in CM 1:4 using water proofing liquid compound as per manufacturer's instructions on other than fair faces brick or concrete surfaces and finishing surfaces even & smooth without using extra cement including taking down cement plaster on brick or concrete surface and description including raking out joints Hacking for key scrubbing down with water,.complete all as specified and directed. Note :- Water proofing liquid compound shall be measured and paid separately. |
| 36 | M&L for Distempering with 1st quality acrylic distemper (ready mixed ) having VOC content less than 50 gm/litre of approved primer over and including 2 mm thick wall care putty on new plastered surface of wall including preparation of surfaces with complete all as specified and directed. |
| 37 | M&L for Distempering with 1st quality acrylic distemper (ready mixed ) having VOC content less than 50 gm/litre of approved manufacturer of required shade and colour complete as per manufacturers specification two or more coats over 2 mm thick wall care putty on old surface of wall including preparation of surfaces by complete removal of existing treatment . complete all as specified and directed. |
| 38 | M & L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive excellent dirt pickup resistance with low VOC less than 50, Antifungal/ Anti Alkali properties in two coats not less than 1.79 litre(undiluted)/10 Sqm diluted with water as per manufacturer's instruction applied over primed surface with fully automatic airless spray machine with a flow speed of minimum 1 litre per minute having a pressure of 3300PSI. Allow 6-8 hrs to dry the surface in between subsequent coats of paint over a coat of acrylic water based exterior grade primer @ 0.90 litre(undiluted)/ 10 sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine and allow 6-8 hrs to dry the surface including prepard surface of wall and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 grit or above to make the surface :- over the new plastered painted surface of wall and sanding of the putty surface with mechanical wall sander (having capacity of min 2.5 kg putty per minute. Step 1: Mix the putty powder by adding water as manufacturer's instruction and mix it with putty mixer with the mixing Step 2: Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine/ manually of putty application finishing the surface even and smooth in level without any undulations. |
| 39 | S&F Steel water tubing, 15mm bore dia, galvanised, \\"medium grade\\" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc including taking down & cleaning for refixing or removal to store, complete all as specified and directed. |
| 40 | S&F Steel water tubing, 20mm bore dia, galvanised, \\"medium grade\\" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc including taking down & cleaning for refixing or removal to store, complete all as specified and directed. |
| 41 | S&F in repair 20 mm dia gun metal ,globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 42 | S&F in repair Vitreous China wash down water closet pan and trap, (pedestal pattern) (Fixing includes bolts, 'P' and 'S' trap and connecting to drain pipe, white seat cover plastic flat bottom and MS Chromium plated hinging device and connection to flush pipe, flushing cistern and also polyethelene flushing pipe) etc complete all as specified and directed. |
| 43 | S&F in repair of PVC 10 Ltr valveless,syphonic action type, flushing cistern, low level,white inlet, ball valve, float and handle including bracket and & supply of flush pipe of polyethylene of low or high density or PVC , 32 mm dia for low level cistern device complete all as specified and directed. |
| 44 | S&F in repair vitreous china wash hand basin white, flat back of bowl size 550x400mm including waste coupling and waste pipe PVC 32 mm dia to be fixed over mild steel bracket including pinning in ends of brackets, complete all as specified and directed. |
| 45 | S & F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in pipe. complete all as specified and directed. |
| 46 | S&F in repairs CP jet spray hygienic spray jet for 15mm bore dia fittings 1 to 1.5m long tube acrylic type complete all as specified and directed. |
| 47 | S&F in repair 15mm bore one way Angle valves, CP fancy type chromium plated screwed both ends for iron pipe or for unions, high pressure with crutch or butterfly handle, screwed both ends (externally threaded) complete all as specified and directed. |
| 48 | S&F in repair 15mm bore two way Angle valves, CP fancy type chromium plated screwed both ends for iron pipe or for unions, high pressure with crutch or butterfly handle, screwed both ends (externally threaded) complete all as specified and directed. |
| 49 | S&F in repair CP Pillar taps fancy type 15 mm bore cast alloy with capasten head screwed down high pressure with without lettered 'Hot or Cold with long screwed shanks and fly-nutsscrewed complete all as specified and directed. |
| 50 | Supply & Fixing in repair 600mmx450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete including dismantling old mirror complete all as specified and directed. |
| 51 | S&F in repair PVC connections 15mm, 450mm long with PTMT nuts washers etc complete all as specified and directed. |
| 52 | S&F Rotational moulded polyethylene water storage tank 1000 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position with PVC float ball valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, complete all as specified and directed. |
| 53 | Dismantling of CI/PVC pipe 75 mm bore fixed to wall or laid in floor or trenches inculding connection all as specified and directed. |
| 54 | Dismantling of CI/PVC pipe 110 mm bore fixed to wall or laid in floor or trenches inculding connection all as specified and directed. |
| 55 | S&F PVC (SWR) pipes 75 mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed. |
| 56 | S&F PVC (SWR) pipes 110 mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches/wall or in floors etc, complete all as specified and directed. |
| 57 | S & F 75 mm bore PVC Bends (SWR) with access door,complete all as specified and directed. |
| 58 | S & F 75 mm bore PVC (SWR) T- Junction with access door, complete all as specified and directed. |
| 59 | S & F 110 mm bore PVC Bends (SWR) , complete all as specified and directed. |
| 60 | S & F 110 mm bore PVC (SWR) T-Double Junction with access door, complete all as specified and directed. |
| 61 | S&F in repair PVC (SWR) Nahanifloor trap of 75 mm dia with CP Grating including jointing with Solvent cement complete all as specified and directed. |
| 62 | S&F PVC (SWR) vent cowl 110 mm dia, complete all as specified and directed. |
| 63 | S&F in repair stainless steel sink , 1.00 mm thick for kitchen or laboratory , with plug waste pipe, washers, including cantilever cast iron brackets, connecting union etc. overall size 495 mm x 420 mm with bowl size 410 mm x 330 mmx160 mm, complete all as specified and directed. |
| 64 | Dismantling of wall & ceiling boards (fiber pulp insulation etc) or insulation boards/slabs/blankets of any thickness, including cover fillets complete all as specified and directed. |
| 65 | S&F Providing and fixing tiled false ceiling of size 595 x 595mm in true horizontal level suspended on interlocking gypric metal grid of hot dipped galvanised steel section (galvanized @ 120 gsm/sqm, both side inclusive) consisting of 3600mm long main 'T' runner size 24x38mm and 0.30mm thick, 1200mm long cross 'T' of size 24 x 25mm and 0.30mm thick, 600mm secondary cross 'T' of size 24 x 25mm and 0.30mm thick, bottom exposed capping of width 24mm of all T-sections shall be of 0.25mm thick PPGI, wall angle is fixed along the perimeters of the ceiling to walls, partitions or columns etc with rawl plugs and wooden screws at 300mm centers Main 'T' runners are then suspended from ceiling using GI slotted cleats of size 27x37x25x1.6m fixed to ceiling with 8mm dia and 45mm long dashfasteners, 4mm GI adjustable rods with galvanised buttfly level clips of size 85x30x0.8mm spaced at max 1200mm centre to centre along main 'T' and not more than 150mm from spliced joints. The last hanger at the end of each main runner should not be greater than 600mm from the adjacent wall, then 1200mm long cross 'T' is interlocked between the main 'T' at 600mm center to center to form a grid of 1200x600mm and then secondary cross 'T' of length 600mm is then interlocked at middle of the 1200x600mm grid to form grids of 600x600mm. Cross tees at the ends having length more than 600mm are to be supported independently. Finally white coloured Gyproc 8mm thick Dew Drop/Granular tiles of size 595x595mm having foil on backside & PVC paper on front side wrapped around edges to be placedin grid complete all as specified and directed. , complete all as specified and directed. |
| 66 | M&L for Providing and laying 60mm thick factory made concrete edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, inishing and sweeping extra sand complete all as specified and directed. |
| 67 | M&L for 75 mm thick PCC 1:2:4 type B-2(using 40 mm graded crushed stone aggregate ). Complete all as specified and directed. |
| 68 | M&L for plain cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in coping, finished fair and even including necessary formwork complete all as specified and directed. |
| 69 | M&L for Cement concrete type C-2 1:3:6 using 40 mm graded crushed stone aggregate in surface channels and drains etc including necessary formwork complete all as specified and directed. |
| 70 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends complete all as specified and directed. |
| 71 | M&L for precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded crushed stones aggregate as in cover slabs, shelves and other similar work set in CM 1:6 complete all as specified and directed. |
| 72 | Dismantling timber scantling Ditto in fillets, rails, posts, rafters, purlins, etc under 40 sq cm in section , any position in unframed work complete all as specified and directed. |
| 73 | S&F, Rolled Mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing ( beam, tee, angle, channel, tubular or flat sections) including distance pieces, cleats etc confirming to Fe 410 (gde E-250) quality 'A' , complete all as specified and directed. |
| 74 | S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of grade Fe-410 (Gde E-250) quality 'A', complete all as specified and directed. |
| 75 | Dismantling of plain or corrugated steel sheeting,any gauge,thickness,including nanital or similar pattern roof covering, S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550MPa as in roof covering/cladding to wall, fixed with self tapping screws. Sheet colour approved by Engineer-in Charge complete all as specified and directed. |
| 76 | Dismantling of plain or corrugated steel sheeting,any gauge,thickness,including nanital or similar pattern roof covering, S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550MPa as in roof covering/cladding/ridges to wall, fixed with self tapping screws complete all as specified and directed. |
| 77 | M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams flat for fair finished surfaces of concrete , complete all as specified and directed. |
| 78 | M&L for RCC M-20 nominal mix (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 79 | M&L for TMT bar 10 mm and over cut to length, bend to shape required including cranking, bending spirally for hoopings for cols, hooking ends and binding with ad including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 80 | M&L for TMT bars 5mm dia and over upto and including 10mm dia as in stirrups cut to length bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with and incl mild steel wiere (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 81 | Writing letters or figures (Block, Roman, Italic or Indian) n exc 30 cm high,painted with thick paint, so that they stand out boldly and solidly without showing signs of brush marks, complete all as specified and directed. |
| 82 | S & F Framed work as in framework of water tanks and similar work conforming to Fe 290 Gde-E-165, complete all as specified and directed. |
| 83 | Excavation in trenches in any type of soil n, exc 1.5m wide and not exc 1.5m in depth and getting out complete all as spfd and directed. |
| 84 | Removal of excavated mtrl to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5meter above the starting point complete all as specified and directed. |
| 85 | M&L for Cement concrete M-10 type C-1, using 20 mm graded crushed stone aggregates as in foundation filling and drains, complete all as specified and directed. |
| 86 | M&L for Plain Cement concrete M-10 (Nominal mix) in foundation filling and mass concrete in surface channel and drains, complete all as specified and directed. |
| 87 | Providing, cement concrete type B0 1:2:4 (12.5mm graded agg) in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly roundedor chamfered angles and throating, complete all as specified and directed. |
| 88 | 15mm thick rendering in CM 1:4 other than fair face of brick surface or stone surface, finished even and smooth without using extra cement complete all as specified and directed. |
| 89 | S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 |
| 90 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed. |
| 91 | M&L for 100 mm thick Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 92 | M&L for 75 mm thick cement concrete 1:4:8 type D-2 (40 mm graded crushed stone aggregates) as in Sub base etc., complete all as specified and directed. |
| 93 | M & L for coloured ceramic parking tiles of size 400mm x 400mm x 12mm laid in floor or wall over 15mm screed bed in CM 1:4 with grey cement and pigment, any shape and size complete all as specified and directed. |
| 94 | M&L for Plain cement concrete, Type C2, 1:3:6 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete, complete all as specified and directed. |
| 95 | S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates and similar work conforming to Fe.410.Gde-E-250 complete all as spfd and directed |
| 96 | S&F Top hangar door guide roller/wheels, of size 100/150mm , fixed at door top member complete all as spfd and directed |
| 97 | S&F Bottom Cast iron hangar door wheels, 150mm dia, 25-40mm thick with 25mm dia gun metal bush, fixed at door bootom member complete all as specified and directed. |
| 98 | S & F Aluminium composite panel (ACP) sheet 5mm thick aluminium layered of approved colour fixed as walls cladding or any position, complete complete all as specified and directed. |
| 99 | M&L for Plain cement concrete, Type D2, 1:4:8 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete, complete all as specified and directed. |
| 100 | M & L for RCC (design mix ) type M-25 (20 mm graded agg) as in Foundations, including rafts, footings, foundation beams; plinth beams; complete all as specified and directed. |
| 101 | M&L for plain cement concrete 50mm thick 1:3:6 type C-2, using 40mm graded crushed stone aggregate as in plinth protection/ foot path/sub base of floor complete all as specified and directed. |
| 102 | M & L for Machine cut kota stone 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed |
| 103 | M&L for 125mm size Butt hinges, heavy weight, cold rolled mild steel and fixed complete all as specified and directed. |
| 104 | M&L for Mild steel sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed |
| 105 | S&F Anodised aluminium powder coated window of any type (two/three track) sliding type aluminium powder coating 50 micron and aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as suitable handle (01 Nos) locking and sliding system complete all as specified and directed |
| 106 | M&L for Sheet glass, 4 mm thick ordinary quality and glazing exc 0.5 sqm in each pane complete all as spfd and as directed |
| 107 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples of any description complete all as specified. |
| 108 | Taking down carefully existing aluminum / copper point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, fan regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed. |
| 109 | Taking down un-serviceable DB of any size and capacity including MCB etc, and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc, complete all as specified and directed |
| 110 | Taking down un-serviceable sub main wiring of any type and any size from wall, ceiling etc. complete all as specified and directed Please Enable Macros to View BoQ information |
| 111 | Taking down un-serviceable sub main wiring of any type and any size from wall, ceiling etc. complete all as specified and directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysDec 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender