Tender For Provn Of Internal Drain In Back Side Of Auditorium Hall , special Repair To Puf Sh No 1119, Provn Of Gazebo In Panagarh Officer Transit Accn And Special Repair To Existing Floor Tiling With Reinforced Cement Concrete In Auditorium Hall At
Tender Value
42.84 Lakhs
Estimated cost
Bid Submission
25 Nov 2026
13 days left
EMD
85800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Purba Bardhaman → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Internal Drain In Back Side Of Auditorium Hall , special Repair To Puf Sh No 1119, Provn Of Gazebo In Panagarh Officer Transit Accn And Special Repair To Existing Floor Tiling With Reinforced Cement Concrete In Auditorium Hall At Pms Under Ge Panagarh
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un reinforced) in ground floors and paving n.exc 15cm thickness (below or above ground (level) and lowering if necessary, removal of the rubbish off the premises complete all as specified and directed. |
| 2 | Demolition of reinforced cement concrete in ground floors and pavings n.exc 15 cm thickness (below or above ground level) and removal of the rubbish off the premises all as specified and directed. |
| 3 | Demolition of brick work built in CM including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removal of the rubbish off the premises all as specified and directed. |
| 4 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing to low lying area and rubbish off the premises. complete all as specified and directed. |
| 5 | Dismantling wrought iron or mild steel work of any description not otherwiseprovided for complete all as spd and directed. |
| 6 | Dismaltaling of plain or corrugated steel sheeting , any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed. |
| 7 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as spd and directed. |
| 8 | Excavating in post holes ( or similar holes) each n.exc 0.5 cum getting out , and removing surplus soil to a distance n.exc 50m and making good surface, in soft/loose soil.complete all as specified and directed. |
| 9 | Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole, laying of cables, pipes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any kind of soil complete all as specified and directed.Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding. |
| 10 | Removing of excavated materials to a distance n. exc 50m and depositing where directed at a level n exc 1.5m above the starting point in oft/loose soil complete all as specified. |
| 11 | M&L for pavings, with mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust ) laying in layers n. exc 10cm thick, watering, ramming and compacted with hand/power roller 8 to 12 tonn roller to required camber and gradient complete all as directed by Engineer-in-Charge. |
| 12 | M&L for broken stone/boulders hard core gauge n.exc 63mm deposited, spred and levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces complete all as spd and directed. |
| 13 | M&L Cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed. |
| 14 | M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in bed concrete for foundation filling & mass concrete complete all as spd and directed. |
| 15 | M&L for cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) in surface channels and drains for benching complete all as spd and directed. |
| 16 | M&L for Providing cement concrete type B-0, 1:2:4 (12.5mm grades aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling). corbels, brackets, etc including frames (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar 1:4 complete with joints to match complete all as spd and directed. |
| 17 | M&Lfor RCC precast cement concrete type B-1 1:2:4 (20mm graded stone aggregate) as in cover slab for drain, mahhole cover etc and similar article with plain face set in cement mortar 1:4 complete all as spd and directed |
| 18 | M & L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as specified and directed. |
| 19 | M & L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed |
| 20 | M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. |
| 21 | M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface of concrete, complete all as specified and directed. |
| 22 | M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 23 | S&F TMT reinforcement bar, conforming to Fe-500, 5mm dia and upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as binding with and including mild steel wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 24 | S&F TMT reinforcement bar, conforming to Fe-500, 6mm to 8mm dia cut to length , bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed) not less than 0.9mm dia or securing with chips. complete all as specified and directed. |
| 25 | S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (Fe 410-W (Gde -E-250) quality A complete all as spd and directed. |
| 26 | S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde E- 250) quality A complete all as spd and directed. |
| 27 | 8. S & F mild steel screws bolts 5 to 10cm dia (machine made) with hexagonal or square heads at one end and screw the other or screwed both end to be fitted with wahsers and on hexagonal or square n.exc 5 cm long complete all as spd and directed. |
| 28 | S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails andfastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410-W (Gde-E-250) quality-B complete all as spd and directed. |
| 29 | SS & F for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts complete all as spd and directed. |
| 30 | S&F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 , the grill shall be inserted in the wall surface including necessary drilling and grouting with cement etc complete all as spd and directed. |
| 31 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed |
| 32 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed |
| 33 | S&F mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges of sheet 1.25mm and 150mm dia or complete all as specified and directed. |
| 34 | M&L, Brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete, all as specified and as directed. |
| 35 | M&L, Brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete, all as specified and as directed. |
| 36 | M&L for old size brickwork with flyash bricks, straight or curved on plan exc 6m mean radius, half bricks thick built in CM (1:4) for edging of path complete all as specified and directed |
| 37 | Taking down chowkats or frames exc 1.5 sqm but n. exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as spd and directed |
| 38 | Taking down of chowkats or frames not exc 1.5sqm each with shutters (without taking off shutters from frames ) complete all as spd and directed. |
| 39 | S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 40 | S&F Factory Made Solid PVC Moulded Door Shutter (with particle board core), 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per Specification & drawing complete all as specified and directed.. |
| 41 | S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other frames/chowkhat of size 50x125 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade ), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS scews having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in -Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately) Note :- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile demension on plus side shall be acceptable but no extra payment on this account shall be made. |
| 42 | S&F for factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately) |
| 43 | S&F for 35mm thick factory made single extruded WPC (wood polymer composite) solid wire gauzed i.e. panel will be of wire gauze in lieu of panel. The comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately) |
| 44 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including Aluminium snap beading for glazing/ paneling, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 45 | S&F for Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 46 | S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples. complete all as specified and directed. |
| 47 | S&F 100mm long butt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed , type B-21 complete all as specified and directed. |
| 48 | S&F 75mm long butt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed , type C-21 complete all as specified and directed. |
| 49 | S&F 200 mm long Aluminium, anodised, barrel tower bolt of extruded section. complete all as specified and directed. |
| 50 | S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as spd and directed. |
| 51 | S&F 150 mm long aluminium alloy handles,fabricated type, anodised complete all as spd and directed. |
| 52 | S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and dirceted. |
| 53 | S&F in repair stainless steel fancy curtain rods with conical end balls suitable for fixing as end of curtain/dropery rods complete all as spd and directed |
| 54 | S&F stainless steel fancy curtain rods with conical end balls suitable for fixing as end of curtain/dropery rods complete all as spd and directed |
| 55 | S&F 40mm wide and 5mm thick PVC door seal (snake guard) with powder coated aluminium frame. complete all as specified and directed. |
| 56 | Dismantling wooden boarding, any description, fixed in any position with nails. complete all as specified and directed. |
| 57 | S&F 18/19 mm thick, lead free PVC board Superior quality of density not less than 0.55 g/cm3 as in moduler shutters/cabimet drawer cupboard cabinet shutter including all frame work as specified and directed by Engr-in-Charge |
| 58 | S&F for 100mm hasp and staple, safety type, brass with mild steel hinge pinincluding bolt to hinge plate and fixed with screws complete all as spd and directed |
| 59 | S&F for Continuous (piano) hinges, width of flaps 40mm mild steel, bright finish or electrogalvanised complete all as spd and directed |
| 60 | S&F for cupboard wardrobe magnetic catch latch complete all as spd and directed. |
| 61 | S & F powder coated aluminium snap grid frame work for false ceiling all as specified. |
| 62 | S&F for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting levelfixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm longcomplete all as specified |
| 63 | S&F for 6mm thick non asbestos fibre cement designer building boards fixed or laid on aluminium frame/grid with screws as flat , complete all as specified and directed. |
| 64 | M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified and directed. |
| 65 | M&L cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) 25 mm thick as in floor for receiving screed bed for floor finishes. complete all as specified and directed. |
| 66 | M&L for 25 mm thick PCC 1:2:4 type B-0 (Using 12.5mm graded crushed stone aggregate) as in floor, finished the surfaces fair & even to receive floor finishes, complete all as specified and directed. |
| 67 | M&L Non skid Ceramic tiles light shade 8 to 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed. |
| 68 | M&L Non Skid coloured ceramic tiles 7 to8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match and including over screed bed or bedding layer of mortar 20 mm thick laying floor finished in CM 1:6 complete all as specified and directed. |
| 69 | M&L Non Skid coloured ceramic tiles 7 to8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surface such as skirtings etc. set and jointed in cement slurry over 10 mm thick rendering in CM 1:4 complete all as specified and directed.complete all as spd and as directed. |
| 70 | M&L for Glazed ceramic tiles Coloured 450 x 300mm 7 to 8 mm thick in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match rendering over 10 mm thick in CM 1:4 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed. |
| 71 | M&L for Green marble work 15 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following typesnt with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 15mm thick Screed bed or backing coat for laying floor finishes in CM 1:6 complete all as specified. |
| 72 | M & L for PCC (1:1.5:3) Type A-0 using 12.5 mm graded aggregate used as in flooring top and finishing complete all as specified and as directed. |
| 73 | M&L for 15mm thick Wearproof topping (incorporating an approved metallicfloor hardner in the proportion recommended by the manufacturer), laid on concrete floors and pavings, and finished even and smooth with an admixture of metallic floor hardner as per manufacturer's instruction complete all as specified and directed. Note :- Metallic hardner shall be measured separately and paid at 'Supplied only' rates |
| 74 | Supply only Metallic floor hardner (Make :- Ultratech smartop floor hardner/Sika chapdur floor hardner) complete all as specified and directed. |
| 75 | Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water etc complete all as directed. |
| 76 | M&L Rendering 15 mm thick cement plaster in CM 1:6 on brick/concrete work surfaces finished fair and even complete all as specified and directed.. |
| 77 | M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. |
| 78 | Supply only liquid Water proofing compound complete all as spd and directed. |
| 79 | S&F Sheet glass 5.5 mm thick , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as spd and directed. |
| 80 | M&L sheet glass 4.8 mm thick ordinary quality and glazing with oil putty and pin in square n. exc 0.50 sqm in each pan complete all as specified and directed. |
| 81 | S&F for 4mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as spd and directed. |
| 82 | Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 15 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete.complete all as specified and directed. |
| 83 | Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 20 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete.complete all as specified and directed. |
| 84 | S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 85 | S&F 25 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 86 | Supply and fix in repair for Gun metal gate valve,20 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed. |
| 87 | Supply and fixed in repairs floor mounted (single piece WC) bowl with cistern for coupled WC with and including UF soft close slim seat cover, hinges, dual flush cistern fitting, fixing accessories and accessories set complete of size 380x655x765 mm with S Trap- 250 mm, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 88 | S&F in repairs cardiff health faucet with SS hose and hook complete all as specified and directed. |
| 89 | S&F in repairs brass CP Tubular towel rail 20mm dia, D type, 60 cm long between flanges complete all as specified and directed. |
| 90 | S&F in repairs toilet roll paper holder with flap of brass chromium plated including screw and chromiun plate brass cleats complete all as specified and directed. |
| 91 | S&F in repairs vitreous china counter top wash hand basin (self rimming) leed NC0483 (Size 600 x 400 x 185mm) colour brilliant / off white including fixing brackets and prepolished granite slab of size 1000 x 600mm size and cutting notch of required size as per the wash hand basin to be fixed in it complete all as specified and directed. |
| 92 | S&F basin mixer without pop up chromium plated complete all as specified and directed. |
| 93 | S&F Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, unionand cap and fixed complete all as spd and directed. |
| 94 | S&F in repair 15mm bore fancy type stop valve/angle cock (multiple) , chromium plated concealed type cast copper alloy, screwed down , high pressure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 95 | S&F in repair PVC connection 15mm size PTMT nuts of length450mm. complete all as specified and directed. |
| 96 | S&F as in repair bib taps cast copper alloy 15mm bore long neck body with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 97 | S&F in repairs grating square 150mm size of PTMT(minimum 100 gms). complete all as specified and directed. |
| 98 | S&F in repairs grating square with waste hole 150mm size of PTMT(minimum 100 gms). complete all as specified and directed. |
| 99 | supply and fixing in repair of PVC Mirror cabinet ,size 330x430 mm single door with mirror colour white complete all as specified and directed make as given inlist of makes as directed by Engineer-in-charge |
| 100 | S&F PVC SWR pipes 150 mm bore single socketed in any length with rubber ring joint fixed to wall with PVC clamps for rain water pipes all as specified and directed |
| 101 | S&F PVC SWR bends of 150 mm bore complete all as spd and as directed by Engr-in-Charge. |
| 102 | S&F in repairs PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joints laid in trenches or in floors all as specified and directed . |
| 103 | S&F in repairs PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls of 110mm dia and as directed |
| 104 | S&F n repairs PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 105 | S&F for PVC SWR bends of 110 mm bore complete all as spd and directed. |
| 106 | S&F PVC (SWR) bends in any radius of 110mm dia complete all as specified and directed. |
| 107 | S&F for PVC SWR bends of 75 mm bore complete all as spd and directed. |
| 108 | S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia complete all as spd and directed. |
| 109 | Supply and fix in repairs PVC SWR Nahani/ Floor trap, multi inlet connection, plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 50 mm, complete all as specified and directed by Engineer in charge. |
| 110 | S&F for PVC (SWR) vent cowl 110 mm bore complete all as spd and directed. |
| 111 | M&L for prepration of newly plastered surfaces of wall and applying one coat of alkali resistanse primer over a coat of 1mm thick wall care putty complete all as specified and directed. |
| 112 | Supply and Fixing (S&F) of self-adhesive, peel-and-stick vinyl wallpaper featuring vintage paper plane design (or approved vintage design). The wallpaper shall be waterproof, stain-proof, washable, and easy to clean. Complete in all respects, including surface preparation, as per manufacturer specifications and direction of the Engineer-in-Charge. |
| 113 | M&L for prepration of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as spd and directed. |
| 114 | M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed. |
| 115 | M&L preparation of old surfaces of steel of any description over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as spd and directed. |
| 116 | M&L preparation of old surfaces of Puf insulated board of any description over 10cm width or girth, not otherwise described and applying two coat of synthetic enamel paint with Gun Spray complete all as spd and directed by Engr-in-Charge. |
| 117 | M&L for writing letters or figures (block, Roman, Italic or indian) n exc 30 cm complete all as spd and as directed |
| 118 | M&L for preparation of surfaces, free from oils, grease, dust and loose or friable particles. paint, cement laitance and other poorly adhering contaminants and supply, filling, insulating, filling connection joints around window and door frames, pipe entries, air-conditioning vents and roller blind housings, vertical/horizontal construction etc by applying PU based 1-component, fast curing Multi-position, highly expansive polyurethane fixing foam with the help of gun, upto depth of 75mm and width not exceeding 20mm, complete all as specified' |
| 119 | M&L for forming fair finish drain channel inner girth 30cm in girth in cement concrete using extra cement complete all as specified and directed. |
| 120 | S&F for 300mm bore reinforced concrete pipes, class NP2 , laid and jointed complete all as spd and directed. |
| 121 | Material and labour for cement concrete bed to drain pipe for 300mm bore of pipe including forming cradles in Cement concrete 1:3:6 Type C2 complete all as specifiedand and as directed. |
| 122 | Taking down carefully existing point wiring of any type (i.e on wooden batten, surface conduit, casing capping or concealed conduit except existing conduit) complete for light, fan, socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets wooden batten, conduit etc including accessories such as wooden gutties/ rawal plug, screw etc including removing materials from site for taking credit of unserviceable items and re-fixing the serviceable items as per schedule and making good disturbed surface of walls, floors etc, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 123 | Taking down carefully existing point wiring of any type (i.e on wooden batten, surface conduit, casing capping or concealed conduit except existing conduit) complete for light, fan, socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets wooden batten, conduit etc including accessories such as wooden gutties/ rawal plug, screw etc including removing materials from site for taking credit of unserviceable items and re-fixing the serviceable items as per schedule and making good disturbed surface of walls, floors etc, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysNov 26, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender