Defence Statutory Bodies & Commissions/Committees Closing in 21 days TDR #58399057

Tender For Demolition And Construction Of Certain Married Accommodation In Dk-I/Ii In Delhi Cantt (Design And Build Basis)

Issued by Statutory Bodies & Commissions/Committees · New Delhi, Delhi
Tender Value
31.10 Crore
Estimated cost
Bid Submission
11 Dec 2026
21 days left
EMD
15 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Demolition And Construction Of Certain Married Accommodation In Dk-I/Ii In Delhi Cantt (Design And Build Basis)

BOQ

Name of Work:- DEMOLITION AND CONSTRUCTION OF CERTAIN MARRIED ACCOMMODATION IN DK-I/II IN DELHI CANTT (DESIGN AND BUILD BASIS)
Sl. No. Item Description
1Schedule ‘A’ Section-IDesign, Build, Development, Construction, Installation and Erection of MARRIED ACCOMMODATIONS IN DK-I/II IN DELHI CANTT which involves the construction of following buildings / structures with allied infra & services as per drawings, scope of work with respective Annexure, DBR, specifications and other documents of the tender, complete all as specified and directed:-(a) Married Accommodation for 42 Officers, Six Blocks, G+3 each(b) Stilt Area under one unit to be used for Parking and services(c) Terrace Tank for fire-fighting (5,000 ltr capacity) and drinking water (10,000 ltr capacity) for all Six blocks(d) Covered Parking, Sub Station Bldg and Pump House Bldg.(e) Fire fighting System works(f) Furniture Works
2Lump sum price worked out by the contractor for Schedule 'A' Section-II (INTERNAL WATER SUPPLY) (Ref pre priced Schedule attached seperately)
3Lump sum price worked out by the contractor for Schedule 'A' Section-III (ROAD/PATH CULVERT/HARD STANDING) (Ref pre priced Schedule attached seperately)
4Lump sum price worked out by the contractor for Schedule 'A' Section-IV (EXTERNAL WATER SUPPLY) (Ref pre priced Schedule attached seperately)
5Lump sum price worked out by the contractor for Schedule 'A' Section-V (EXTERNAL ELECTRIC SUPPLY) (Ref pre priced Schedule attached seperately)
6Lump sum price worked out by the contractor for Schedule 'A' Section-VI (SEWAGE DISPOSAL) (Ref pre priced Schedule attached seperately)
7Lump sum price worked out by the contractor for Schedule 'A' Section-VII (AREA DRAINAGE) (Ref pre priced Schedule attached seperately)
8Lump sum price worked out by the contractor for Schedule 'A' Section-VIII (WALL / CHAINLINK / FENCE / GATE) (Ref pre priced Schedule attached seperately)
9Lump sum price worked out by the contractor for Schedule 'A' Section-IX (DEMOLITION WORKS) (Ref pre priced Schedule attached seperately)
10Schedule ‘A’ Section- X (MISCELLANEOUS ITEMS)
11(A) (INTERNAL WATER SUPPLY)
12M&L for CP Brass Wall Mixer 15mm bore for mixing hot & cold water screwed down for pipe and fixed complete all as specified and directed.
13M&L for CP Brass Wash Hand Basin Mixer 15mm bore for mixing hot & cold water screwed down for pipe and fixed complete all as specified and directed.
14S&F for CP Brass Sink Mixer 15mm bore for mixing hot & cold water screwed down for pipe and fixed complete all as secified and directed.
15S&F for Bib Tap CP Brass Short body 15mm bore screwed down for pipe and fixed complete all as secified and directed.
16S&F for Stainless Steel Kitchen Plate Rack 900x1219x250mm with hanging to wall complete all as secified and directed.
17S&F for Soap dish CP Brass complete all as secified and directed by Engineer in Charge.
18S&F Stainless steel Towel Ring round shape complete all as secified and directed by Engineer in Charge.
19S&F Liquid soap dispenser complete all as secified and directed by Engineer in Charge.
20S&F Bathroom Mirror Cabinet Fancy type complete all as secified and directed by Engineer in Charge.
21S&F CP Brass Toilet paper holder with flap complete all as secified and directed by Engineer in Charge.
22S&F Stainless steel Towel Rack premium quality 24\\" complete all as secified and directed by Engineer in Charge.
23(B) (ROAD, PATH AND CULVERT)
24M&L for applying 2.5mm thick road marking strips/lines/dashes/arrows/letters (retro-reflective) of specified shade/colour using hot thermosplatic material by fully/semi automatic thermoplastic paint applicator machine fitted with profiles shoes glass beads dispenser propane tank heater and profile shoes driven by experienced operator on road surface including cost of materials labour etc on new/old road surface including T&P cleaning the road surface of all dirt seals, oil, grease and foreigh material etc complete all as specified and directed. Notes :- (i) The quotes rates shall be inclusive of mixing glass beads (ballotini) in thermoplastic material. (ii) The quantity of ballotini included/mixed during the manufacture of material should not be less than 20% by mass of mixture or applied to the surface of the thermoplastic immediately application is complete @ 300 grms / sqm as directed by Engr -in-Charge. The ballotini shall comply with BS6088 : 1981 (1993) \\"Specification for Solid Glass Beads for use with Road Marking\\".
25S&F refelective convex mirror of dia 800 mm and mounted over mild steel pipe 40mm bore (medium grade) and 2.5 mtr long including excavation of post holes of size 400x400x600 mm and PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate as in foundation, complete all as specified and directed.
26(C) EXTERNAL WATER SUPPLY
27Supply, laying, jointing & testing 100mm bore (Nominal size) Ductile Iron pressure pipes for water, Centrifugally Cast (Spun) with spigot & socket end, Class K-7 confirming to IS:8329(2000) amended upto date suitable for (push-on) rubber gasket jointing with centrifugally applied inside cement mortar lining with Portland Slag Cement as per and external metallic Zinc Coating with finishing layer of Bitumen coating complete with EPDM rubber gasket confirming to IS: 5382 all as specified and directed by Engineer-in-Charge.
28M&L for making hole below the road/hard standing by mannaul auger or hand drill without damaging road for inserting pipe upto 150 mm dia complete all as specified and directed by Engineer-in-Charge.
29M&L for construction of valves pit chamber having intermal dimension 900 mm x 900 mm x 900 mm (internal height) using PCC (1:4:8) 40mm graded stone aggregate for foundation 15 cms, thick, 23 cm thick wall in CM (1:4), 10mm thick rendering all around the brick work in cm 1:6, PCC (1:2:4) type B1 coping with 20mm graded aggregate for grouting MS frame including 3mm tick MS top sheet cover with locking arrangement including 50mm pad lock with double key angle iron including painting of steel surface with two coats of synthetic enamel paint over a coat of red oxide primers including necessary excavation & earth work in any type of soil, returning filling in and removal of surpuls soil to a distance not exceeding 50 mtrs all as specified and shown on drawings and including demolition/ dismentling of existing valve chamber, complete all as specified and directed.
30M&L for road/ hard standing cutting for laying of water pipe lines upto 100mm dia and good to match with existing surface complete all as specified and directed by Engineer-in-Charge.
31(D) EXTERNAL ELECTRIC SUPPLY
32Supply, installation, testing and commissioning of distribution Transformer suitable for outdoor installation as per following specifications :-(a). Rating – 400 KVA, 11/0.433KV(b) Standard – IS 1180 (part-I) 2014, & 2026(c) Vector Group – Dyn11(d) Cooling - ONAN(e) Winding - Copper(f) Magnetic Core – Prime grade of M4 or better(g) HV Power Frequency (KV rms) – 28 KV(h) HV Impulse withstand voltage (KV peak) – 75 KVp(j) Energy Efficiency Level – 3 (as per IS:1180 Part- 1 2014 amended upto date)(k) % impedance - 4.5% with IS tolerance(l) Temperature Rise – 40/45 deg C (Max) for Oil / Winding.(m) Tap Changer- OLTC, 7 steps each of 2.5% to vary voltage from +5% to -10%(n) Standard Accessories - As per IS:1180(Part-1): 2014Note : Transformer shall be BIS certified and shall have valid type test report issued by NABL accredited BIS approved Lab.
33Supply, installation, testing and commissioning of distribution Transformer suitable for outdoor installation as per following specifications :-(a). Rating – 200 KVA, 11/0.433KV(b) Standard – IS 1180 (part-I) 2014, & 2026(c) Vector Group – Dyn11(d) Cooling - ONAN(e) Winding - Copper(f) Magnetic Core – Prime grade of M4 or better(g) HV Power Frequency (KV rms) – 28 KV(h) HV Impulse withstand voltage (KV peak) – 75 KVp(j) Energy Efficiency Level – 3 (as per IS:1180 Part- 1 2014 amended upto date)(k) % impedance - 4.5% with IS tolerance(l) Temperature Rise – 40/45 deg C (Max) for Oil / Winding.(m) Tap Changer- OLTC, 7 steps each of 2.5% to vary voltage from +5% to -10%(n) Standard Accessories - As per IS:1180(Part-1): 2014Note : Transformer shall be BIS certified and shall have valid type test report issued by NABL accredited BIS approved Lab.
34Supply, installation, testing and commissioning of manufacturer’s factory manufactured and tested sheet steel clad / enclosed HT Vacuum Circuit Breaker (VCB) switchgear, indoor type, dust & vermin proof, motorised, as well as manually charged, fully interlocked , horizontal draw out horizontal isolation type, floor mounted , 11 KV, 630 Amps, 3 phase,50 Hz, 21 KA for 0.1 sec as per IEC 62271-200.2. extendable type complete. The charging time of motor shall be less than 15 Sec making it suitable for rapid auto reclosing duty, and safety shutters shall be provided to cover up the fixed high voltage contacts on bus bar and cable side when the bus trunk is moved to test/isolation positionwith all standard accesssories, and metering equipments and comprising of followings complete all as specified and directed:-(a) Three single phase horizontal draw out type resin cast line type potential transformer of 11KV/110 volts, 50VA burden per phase class 1.0 accuracy connected star/star on HV side with HV&LV fises, isolating plugs, for HV side and LV connection.(b) CTs dual ratio, 50/25/5+5 Amps rating, class 5 P10 for protection & class 1.0 for metering 10 VA burden, short time rating 25 KA for 0.1 sec. suitable for 11 KV = 03 Nos.
35(c) Instrument & Protection Panel- Numerical relay with LCD display -3 OC+1 E/F with IDMT/DMT charactriestic selectable at site, inbuilt master trip & trip circuit supervision function, inrush protection, record and store at least 100 Event with Date and Time stamp, Last Five Fault Records stored in Nonvolatile memory, self supervision function, Minimum 4 Digital Binary Inputs and 6 digital output contacts, Modbus Communication protocol with RS-485 Port, Breaker Control (ON/OFF) feature.The setting for over current shall be 50-200% of 5A (In the step of 10%) and for Earth fault element from 20-80% of 5A(In the step of 10%).(d) Multifunctional Meter for current, Voltage, Power factor, KVA, KVAR, Frequency KWHR and Max demand recording and indicationg.(e) LED indicating lamps, Breaker ON, Breaker OFF, Spring charged, trip circuit healthy with push button, Auto trip indicator, RYB phase indications.(f) Switch for closing / tripping of VCB(g) Heater with switch , thermostat and illumination.(h) 3 Pin plug socket with switch.(i) 01 No shunt trip coil and closing coil 24V DC(j) Power, pack unit 24V DC with dry rechargeable batteries complete.
36Supply and laying HDPE DWC pipe ISI: 16205 (Part-24) marked for electric cable protection across road crossing/hard standing/along wall of following sizes :-
37(i) 63/50 mm (OD/ID) Nominal dia
38(ii) 90/75 mm (OD/ID) Nominal dia
39(iii) 110/95 mm (OD/ID) Nominal dia
40Making hole below the road/hard standing by mannaul auger or hand drill without damaging road for inserting pipe upto 80 mm dia complete all as specified and directed (Note: Pipe shall be measured & paid separately)
41Supply, installation, testing and commissioning of factory made type tested (TTA) as per IS/IEC: 61439 : 2011 Part 1&2, rated fault level of 65KA for 1 sec, totally enclosed, IP-54, dust and vermin proof, free standing, fully compartmentalized cubicle type front & back openable door LT Panel suitable for 415 Volts, 3-phase, 50Hz, 4 wire AC electric system, outdoor type fabricated from 3.15 mm thick CRCA sheet steel,epoxy polyester powder coated of flint grey shade (RAL-7032) with automatic 9 tank process, 4-pole Bus bar with electrolytic grade Aluminium strip of suitable rating with colour coaded heat shrikable sleeves supported on non-hygroscopic DMC/SMC insulators complete with gland plates, lifting hooks, ventilating louvers,bus bars inter connections, earthing terminals, labeling , cable alley suitable for termination of cables, PCC foundation including supply and fixing of following switchgear and accessories in the panel (Main LT panel, DK-II) :-
42Incomer(i) ACB 4 Pole -800 Amps, 50 KA, 415V rating, mannual draw out type, with advance self powered electronic protection unit, neutral overload protection, inbuilt temp protection - 01No(ii) Bus Bar 4-pole 800 Amp Aluminium strip - 01 Set (iii) Digital type Multifunction meter 100mm square dial suitable to measure Amp, Volt, KHW & PF complete with CT - 01 Nos(iv) LED type phase indicator lamp (RYB) - 01 SetOutgoing(i) MCCB 4 Pole 300 Amp 36 kA, 415V - 02 Nos (DG Panel + 01 Spare)(ii) MCCB 4 Pole 160 Amp 25 kA, 415V - 05Nos (Non essential bldg load panels 1 , 2 , 3 & 4 + APFC Panel).(iii) LED type phase indicator lamp (RYB) - 07 Set
43Supply, installation, testing and commissioning of factory made type tested (TTA) as per IS/IEC: 61439 : 2011 Part 1&2, rated fault level of 65KA for 1 sec, totally enclosed, IP-54, dust and vermin proof, free standing, fully compartmentalized cubicle type front & back openable door LT Panel suitable for 415 Volts, 3-phase, 50Hz, 4 wire AC electric system, outdoor type fabricated from 3.15 mm thick CRCA sheet steel,epoxy polyester powder coated of flint grey shade (RAL-7032) with automatic 9 tank process, 4-pole Bus bar with electrolytic grade Aluminium strip of suitable rating with colour coaded heat shrikable sleeves supported on non-hygroscopic DMC/SMC insulators complete with gland plates, lifting hooks, ventilating louvers,bus bars inter connections, earthing terminals, labeling , cable alley suitable for termination of cables, PCC foundation including supply and fixing of following switchgear and accessories in the panel (Main LT panel, DK-I) :-
44Incomer(i) MCCB 4 Pole, 400 Amps, 50 KA, 415V, (Ics=100% Icu) rating - 01No(ii) Bus Bar 4-pole 400 Amp Aluminium strip - 01 Set (iii) Digital type Multifunction meter 100mm square dial suitable to measure Amp,Volt,KHW & PF complete with CT - 01 Nos(iv) LED type phase indicator lamp (RYB) - 01 SetOutgoing(i) MCCB 4 Pole 160 Amp 25 kA, 415V - 04Nos (Non essential bldg load panels 1 & 2 + DG Panel + 01 Spare).(ii) MCCB 4 Pole 100 Amp 16 kA, 415V - 01 Nos (APFC Panel)(iii) LED type phase indicator lamp (RYB) - 05 Set
45All as per item srl no. 14 here-in-before but PTTA and comprising of following switchgear and accessories (DG Panel, DK-II) :-Incomer(i) MCCB 4 Pole, 300 Amps, 36 KA, 415V, (Ics=100% Icu) rating -01No(ii) Bus Bar 4-pole 300 Amp Aluminium strip -01 Set (iii) Digital type Multifunction meter 100mm square dial suitable to measure Amp,Volt,KHW & PF complete with CT -01 Nos(iv) LED type phase indicator lamp (RYB) - 01 SetOutgoing(i) MCCB 4 Pole 100 Amp 16 kA, 415V -05Nos (Essential load panels 1,2,3 & 4 + 01 Spare).(ii) LED type phase indicator lamp (RYB) - 05 Set
46All as per item srl no. 14 here-in-before but PTTA and comprising of following switchgear and accessories (DG Panel, DK-I) :-Incomer(i) MCCB 4 Pole 160 Amps, 25 KA, 415V, (Ics=100% Icu) rating -01No(ii) Bus Bar 4-pole 160 Amp Aluminium strip -01 Set (iii) Digital type Multifunction meter 100mm square dial suitable to measure Amp,Volt,KHW & PF complete with CT -01 Nos(iv) LED type phase indicator lamp (RYB) - 01 SetOutgoing(i) MCCB 4 Pole 100 Amp 16 kA, 415V -03 Nos (Essential load panels 1 & 2 + 01 Spare).(ii) LED type phase indicator lamp (RYB) - 03 Set
47All as per item srl no. 14 here-in-before but PTTA and comprising of following switchgear and accessories (Essential Load Panel, DK-I & II) :-Incomer(i) MCCB 4 Pole 100 Amps, 16 KA, 415V, (Ics=100% Icu) rating -01No(ii) Bus Bar 4-pole 100 Amp Aluminium strip -01 Set (iii) Digital type Multifunction meter 100mm square dial suitable to measure Amp,Volt,KHW & PF complete with CT -01 Nos(iv) LED type phase indicator lamp (RYB) - 01 SetOutgoing(i) MCCB 4 Pole 63 Amp 16 kA, 415V -03 Nos (Lift 1 & 2 + 01 Spare).(ii) MCCB 4 Pole 40 Amp 16 kA, 415V -01 Nos (Fire Pump).(ii) LED type phase indicator lamp (RYB) - 04 Set
4819. All as per item srl no. 14 here-in-before but comprising of following switchgear and accessories (100 KVAR, APFC Panel, DK-II) :-Incomer(i) MCCB 4 Pole 160 Amp, 25 kA, 415V -01No (ii) Bus Bar 4-pole 160 Amp Aluminium strip -01 Set (iii) LED type phase indicator lamp (RYB) - 01 Set(iv) 8 Step APFC Relay - 01 No(v) Exhaust Fan with Filter - 02 NosOutgoing(a) 20 KVAR Capacitor Bank - 03 No (i) MCB TP 50A, 10KA, D-Curve -03 No (ii) Capacitor Duty Contactor 20 KVAR -03 No (iii) Control MCB 6A -01 No (iv) ON/OF Indicator LED 240V AC -06 Nos (v) ON/OF Push Button -06 Nos (vi) Auto/Manual selector switch -03 No (vii) Side mounting Add-ON Auxiliary Contactor block -03 No (viii) 480V AC Capacitor HD -22.10x3=66.30 KVAR (ix) 20 KVAR 7% Al Detuned Reactor - 03 No
49(b) 10 KVAR Capacitor Bank - 03 Nos (i) MCB TP 32A, 10KA, D-Curve - 03 Nos (ii) Capacitor Duty Contactor 10 KVAR - 03 Nos (iii) Control MCB 6A - 03 Nos (iv) ON/OF Indicator LED 240V AC - 06 Nos (v) ON/OF Push Button - 06 Nos (vi) Auto/Manual selector switch - 03 Nos (vii) Side mounting Add-ON Auxiliary Contactor block -03 Nos (viii) 480V AC Capacitor HD -11.10 x 3=33.30 KVAR (ix) 10 KVAR 7% Al Detuned Reactor - 03 No (c) 5 KVAR Capacitor Bank - 02 Nos (i) MCB TP 20A, 10KA, D-Curve - 02 Nos (ii) Capacitor Duty Contactor 5 KVAR - 02 Nos (iii) Control MCB 6A - 02 Nos (iv) ON/OF Indicator LED 240V AC - 04 Nos (v) ON/OF Push Button - 04 Nos (vi) Auto/Manual selector switch - 02 Nos (vii) Side mounting Add-ON Auxiliary Contactor block - 02 Nos (viii) 480V AC Capacitor HD -5.50x2=11.00 KVAR (ix) 10 KVAR 7% Al Detuned Reactor - 02 No
50All as per item srl no. 14 here-in-before but comprising of following switchgear and accessories (50 KVAR, APFC Panel, DK-I) :-Incomer(i) MCCB 4 Pole 100 Amp, 16 kA, 415V -01No (ii) Bus Bar 4-pole 100 Amp Aluminium strip -01 Set (iii) LED type phase indicator lamp (RYB) - 01 Set(iv) 7 Step APFC Relay - 01 No(v) Exhaust Fan with Filter - 02 NosOutgoing(a) 20 KVAR Capacitor Bank - 01 No (i) MCB TP 50A, 10KA, D-Curve -01 No (ii) Capacitor Duty Contactor 20 KVAR -01 No (iii) Control MCB 6A -01 No (iv) ON/OF Indicator LED 240V AC -02 Nos (v) ON/OF Push Button -02 Nos (vi) Auto/Manual selector switch -01 No (vii) Side mounting Add-ON Auxiliary Contactor block -01 No (viii) 480V AC Capacitor HD -22.10 KVAR
51(b) 10 KVAR Capacitor Bank - 02 Nos (i) MCB TP 32A, 10KA, D-Curve - 02 Nos (ii) Capacitor Duty Contactor 10 KVAR - 02 Nos (iii) Control MCB 6A - 02 Nos (iv) ON/OF Indicator LED 240V AC - 04 Nos (v) ON/OF Push Button - 04 Nos (vi) Auto/Manual selector switch - 02 Nos (vii) Side mounting Add-ON Auxiliary Contactor block -02 Nos (viii) 480V AC Capacitor HD -11.10 x 2 = 22.20 KVAR (ix) 10 KVAR 7% Al Detuned Reactor - 02 No (c) 5 KVAR Capacitor Bank - 02 Nos (i) MCB TP 20A, 10KA, D-Curve -02 Nos (ii) Capacitor Duty Contactor 5 KVAR -02 Nos (iii) Control MCB 6A -02 Nos (iv) ON/OF Indicator LED 240V AC -04 Nos (v) ON/OF Push Button -04 Nos (vi) Side mounting Add-ON Auxiliary Contactor block -02 Nos (vii) 480V AC Capacitor HD -5.50 x 2 = 11.00 KVAR (viii) 10 KVAR 7% Al Detuned Reactor - 02 No
52Supply, install, testing and commissoning of MCCB 4-pole, 160 Amp, 25 KA rating duly enclosed in a sheet metal enclosure suitable for indoor mounting on wall. Please Enable Macros to View BoQ information
53Supply, install, testing and commissoning of MCCB 4-pole, 160 Amp, 25 KA rating duly enclosed in a sheet metal enclosure suitable for indoor mounting on wall. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58399057
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 31.10 Crore
LAST DATE 11-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender for Demolition And Construction Of Certain Married Accommodation In Dk-I/Ii In Delhi Cantt (Design And Build Basis)
Basic Detail
Tender No CEDZ/TOKEN-06 OF 2026
Bidding Type Tender
Location
City New Delhi
State Delhi
Key Dates
Publish Date 05 Nov 2026
Submission Date 11 Dec 2026
Open Date 16 Dec 2026
Finance
Tender Value 31.10 Crore
Tender Fee 3000
EMD 15 Lakhs
Exemption Available
Document List
5efda523-9963-41ed-b946-f8b4c667d09d.html
BOQ_894602.xls
Drawing.pdf
Tendernotice_1.pdf
uploadtender.rar

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 05, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 11, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 21 days
Dec 16, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 26 days

Tender Documents

Download All (ZIP) ↓
html

5efda523-9963-41ed-b946-f8b4c667d09d.html

xls

BOQ_894602.xls

pdf

Drawing.pdf

pdf

Tendernotice_1.pdf

rar

uploadtender.rar

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender