Tender For Rrenovation Of Vof Flats At Rbi Staff Quarters, Gandhinagar, Jaipur
Tender Value
40.30 Lakhs
Estimated cost
Bid Submission
26 Nov 2026
14 days left
EMD
80600
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Rrenovation Of Vof Flats At Rbi Staff Quarters, Gandhinagar, Jaipur
BOQ
| Sl. No. | Item Description |
| 1 | 1. Carefully dismantling and removing of existing mosaic flooring/ Kota stone / ceramic tile or any other flooring / skirting, sunken fillings such as cinder filling / brick bat coba / dado, etc. from bathroom, toilet or wherever required including disposing off debris out of Bank's premises at approved dumping ground of local administration, including all lead and lift etc. all complete as directed by Bank’s Engineer. Note:- This item will be operated in dressing area, bathrooms, wash basin area and toilets.a) Carefully dismantling of Entrance wall, toilet, wash basin area and bathroom (approximate area = 9 Sqm.) b) Carefully dismantling all plumbing & sanitary fittings. Looking mirror, geyser, G.I. pipeline, existing flushing cistern including flush pipe, brackets, W.C. seat, wash basin with brackets, C.P./ Brass fittings, etc. from one flat.c) Dismantling of skirting: Carefully dismantling all the existing tile/stone skirting with backing mortar in the flat and balcony. d) Taking out door shutter of dressing area, bathroom & toilet with doorframe, 01 window of toilet & dressing area with window frame & grills including stone/brick masonry walls including cement plaster.e) Dismantling of existing masonry wall including cement plaster in dressing area & toilet area. Approx. qty. 3.50 Sqm.Work includes disposal of debris out of Bank premises, considering the salvage value of dismantled material, making good the damages with cement mortar 1:4 (1 cement : 4 sand) or plain cement concrete 1:2:4 (1 cement : 2 sand : 4 stone chips 20 mm. nominal sie) as directed by Bank's Engineer. |
| 2 | 2. Providing and laying brick work of required thickness with best quality locally available brick in cement mortar 1:6 (1 cement: 6 coarse sand) including racking out joints, scaffolding, curing for partition walls, support walls of washbasin & platform of urinals, etc. all complete as directed by Bank's Engineer. |
| 3 | 3. Providing and constructing half brick wall in cement mortar 1:4 (1 Cement: 4 coarse sand) at all levels, using best quality locally available bricks including providing key with adjoining stone/brick masonry wall, as per site requirement including racking out joints, curing etc., all complete as directed by Bank's Engineer. |
| 4 | 4. Providing and applying plain cement plaster in 20 mm. thick in cement mortar 1:4 (1 cement: 4 coarse sand) or level to be match with surrounding area and both faces of walls including scaffolding, curing, etc. all complete as directed by Bank’s Engineer. |
| 5 | 5. Providing and applying polymer based two compound water proofing treatment to the sunken portion of the toilets, etc. by using products of M/s. Pidilite, M/s. Fosroc, M/s. Sika, M/s. BASF, M/s. MC-Bouchemie or any other equivalent in the following steps: -a) Thoroughly cleaning of all surfaces of sunken portions to be treated.b) Grouting and injecting polymer cement slurry as per manufacturer’s specifications into the R.C.C. members till its refusal.c) Repairing the damaged portions of the R.C.C. members with polymer concrete / mortar as per manufacturer’s specifications.d) Providing and applying 20 mm. thick water proofing cement plaster 1:4 (I cement: 4 coarse sand) mixed with water proofing compound as per manufacturer’s specifications to the sunken floor and sides including rounding off junctions / corners with water proofing cement mortar, etc. all complete.e) Providing and applying a coat of polymer water proofing primer and two coats of two compound based water proofing polymer/ chemical of M/s. Pidilite, M/s. Fosroc, M/s. Sika, M/s. BASF, M/s. MC-Bouchemie or any other equivalent approved make as per manufacturer’s specifications to the sunken floor, sides, etc.; testing the treated surface by ponding method for 72 hours.f) Repeat the treatment till no seepage is observed on the treated surface.g) Providing and laying 15 mm. thick protective layer of plain cement plaster in cement mortar 1:4 (1 cement: 4 coarse sand) over the treated surface. Work also includes making through hole across the stone masonry wall of 200 mm. to 450 mm. thick up of required size for embedding G.I. pipe of 15 mm. diameter in stone masonry for draining out the seepage leakage water, if any, and filling with cement mortar 1:2 (1 cement: 2 coarse sand) including supplying G.I. pipe of 200 mm. to 450 mm. length. Note: - Single measurement of the sunken floor and its sides shall only be considered for payment for all sub items of work. |
| 6 | 6. Providing and laying brick bat coba to the sunken floors using best quality locally available well burnt sliced bricks in cement mortar 1: 4 (I cement : 4 coarse sand) mixed with water proofing compound of approved make as per manufacturer's specifications, roughening the top layer of cement mortar / top surface of sunk filling with broom to receive the flooring, etc. all complete as directed by Bank's Engineer.Note: - No deduction for squatting / w.c.pan, C.I. pipes, etc. will be made for measurement purpose. |
| 7 | 7. Providing and laying R.C.C. 1:1 ½ :3 (1 cement: 1½ coarse sand : 3 aggregate) for lintel, shelves, platform, slab etc. excluding reinforcements but including compaction, centering, shuttering, curing, finishing, cutting pockets in walls/slab to provide necessary bearing at all height and level, etc. complete all as directed by Bank`s Engineer. |
| 8 | 8. Supplying, straightening, cutting, bending, placing in position and binding & tieing with binding wire TMT steel bar grade Fe415 of approved manufacturer in required diameter including cost of 16 SWG binding wire etc. complete all as directed by the Bank`s Engineer. |
| 9 | 9. Providing and fixing floor mounted, white/ivory colour vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white/ivory colour vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. (Basic Price = Rs. 12000/- including GST)Make: hindware or approved equivalent Ref.-Model: Dome series |
| 10 | 10. Wash Basin (Full pedestal type): Providing and fixing in position White China vitreous first quality Full Pedestal Wash Basin of approved brand/make of approximate size 520x460X855 mm with necessary , 32 mm dia. CP brass waste coupling, 32mm dia C.P. Bottle trap with wall connection pipe and flange, 32mm CPVC pipe conforming to IS 15778 of approximate length 1.00 mt including required fittings/ accessories, providing / making connections from waste coupling to termination over Nahani Trap below, cutting, jointing, wastage, making necessary chases in wall, fixing and concealing pipe in wall , making good all damages to match with the adjoining areas, taking away debris out of Bank’s premises etc. Complete all as directed. ref. Jaquar kubixBasic price of a set of Wash Basin + padestal, shall be Rs.6000.00 including GST. |
| 11 | 11. Structural steel work- Carefully dismantling of 03 nos. stone masonry wall for making hall. Approx. size 3 mt x 3 mt. x 17\\" thick including cement plaster. Providing and fixing riveted, bolted or welded in built up sections ISMB 200, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. The work includes packing with Conbextra GP 2 Chemical on both ends of the girder with MS steel zaali after fixing of minimum 12 MS Props in all floors as directed by engineer in charge. |
| 12 | 12. Providing and fixing Stainless steel SS grade 304, curtain rod 25 mm. dia 1.20 m.m. thick with decorative side/end Stainless steel SS grade 304, brackets (curtain rod) 25 m.m. dia 1.20 m.m. thick, S.S. screws and wooden plugs, etc., wherever necessary complete and as per the sample as approved by the Engineer-in-charge. |
| 13 | 13. Supplying and laying 600 mm. X 1200 mm. ceramic non-skid tiles of approved make and shade, finish in flooring, laid to desired level, slope and pattern, on 20 mm. thick cement mortar 1:4 (1 cement: 4 coarse sand) bedding set in cement slurry, jointing neatly with white cement mixed with matching pigment, cleaning, curing, etc. all complete as directed by Bank's Engineer. The basic rate of tiles shall be Rs.600/- per Sqm inclusive of all taxes, GST at site. |
| 14 | 14. Providing and laying 600 x 1200 m.m. size approved 1st quality ceramic tiles of approved make, size and finish in dado work in utility area, toilets, bathrooms & wash basin area laid on average 15 mm. thick cement mortar 1:3 (1cement: 3 coarse sand) bedding set in cement slurry including jointing with polymer cement grout of matching shade or white cement slurry mixed with polymer and matching pigment, cleaning, curing, making good the damages with cement mortar, cleaning, etc. all complete as directed by Bank’s Engineer. The basic rate of tiles shall be Rs. 600/- per Sqm inclusive of all taxes, GST at site.Note: - 1. Exposed area shall only be measured and paid for. 2. No extra payment will be made for removing and re-fixing of window shutters and beading, if so required, for proper completion of the work. |
| 15 | 15. Providing and laying approved quality Double charges vitrified tiles of 600 x 600 mm of approved manufacture make and shade in flooring in required design and pattern on the existing flooring with approved quality cement based high polymer modified quick set tile adhesive (water based) in average 6 mm. thickness, filling the joints with polymer cement grout or white cement slurry mixed with polymer and matching pigment, cleaning, curing, etc. The rate shall include for additional thickness of tile fixing adhesive, if so required to maintain proper floor level/slope and the cost of preparation of surface by making of deep grooves by machine, hacking of surface to receive the flooring, cleaning; disposal of debris out of Bank’s premises, including all lead and lift etc. all complete as directed by the Bank’s Engineer. The basic rate of tiles shall be Rs. 600/- per Sqm inclusive of all taxes, GST at site.Note: - 1. This item will be operated in bedrooms, living room, utility area & passage, etc.2. Exposed plan area shall only be measured and paid for. |
| 16 | 16. Providing and fixing approximately 150 mm. high, vitrified tiles of approved make in skirting (tiles cut from approved size) wherever required; in all colours, design and pattern; laid on 12 mm. average thick cement mortar 1:3 (1 cement: 3 coarse sand) backing, grouting joints with polymer cement grout or white cement slurry mixed with polymer and matching pigment, cleaning, curing, etc. The rate shall include for cleaning, disposal of debris out of Bank’s premises, etc. all complete as directed by Bank’s Engineer. Note: - 1. This item will be operated in bedrooms, living room & passage, etc.2. Exposed area of vitrified tile skirting shall only be measured and paid for. |
| 17 | 17. Providing and laying 10 mm. thick acid and/or alkali tiles of approved make and shade, finish in flooring & skirting in required disign and pattern on the existing flooring, laid to desired level, slope and pattern, on 10 mm. thick cement mortar 1:4 (1 cement: 4 coarse sand) bedding set in cement slurry, jointing neatly with white cement mixed with matching pigment. The rate shall include cleaning, curing, the cost of preparation of surface by making of deep grooves by machine, hacking of surface to receive the flooring, disposal of debris out of Bank’s premises, including all lead and lift, etc. all complete as directed by Bank's Engineer. Note: - 1. This item will be operated in balcony.2. Exposed plan area shall only be measured and paid for. |
| 18 | 18. Providing and fixing 15-16 m.m. thick premium quality Zed Black in single piece for straight length (maximum up to 3.00 mtr.), gang saw cut, mirror polished, premoulded and prepolished, machine cut for platforms, window sill & storage shelves and similar locations of required size, approved shade, colour and texture laid over 20 m.m. thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish, making necessary holes etc. complete at all levels. The rate should be inclusive of providing opening and fixing granite stone, over and above corresponding basic item, in facia and drops of width upto 150 m.m. with epoxy resin based adhesive, including cleaning etc. Note: - 1. This item will be operated in utility area.2. Only plan surface area will be measured no extra payment will be made for making opening.3. The basic rate is Rs. 2,500/- per Sqm. including GST. |
| 19 | 19. Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 20 m.m. nomial dia in Concealed work/ external work (SDR -11) including cutting chases and making good the walls etc., having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 mt. spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. |
| 20 | 20. Providing and fixing 75 m.m. dia. PVC pipe of approved make for soil waste and vent pipe line including fittings such as tee bend, Y junction conforming to IS with sulation joint (heavy quality) including embedded in PCC horizontal length in floor. Note: - Length of pipe including fittings will be measured in running metre for payment. |
| 21 | 21. Providing and fixing 100 m.m. dia. PVC pipe of approved make for soil waste and vent pipe line including fittings such as tee bend, Y junction conforming to IS with sulation joint (heavy quality) in vertical & horizontal line from flats to manhole chambers including excavation of soil & concrete if required. Note: - Length of pipe including fittings will be measured in running metre for payment. |
| 22 | 22. Providing and fixing S.S. Jali of 100 mm dia with or without waste pipe hole as per directions of Engineer-in-Charge. |
| 23 | 23. Providing and fixing 5.00 m.m. thick bevelled edge mirror of superior glass (of approved quality) complete with 6.00 m.m. thick hard board backing fixed to wall with S.S./C.P. brass screws and washers and covered with studs complete, etc. all complete as directed by Bank's Engineer. |
| 24 | 24. Providing and fixing PVC floor trap of self cleaning design without vent arm complete, including cost of cutting and making good the walls and floors: 100 m.m. inlet and 75 m.m. outlet, as per IS, etc. complete in all respect as directed by engineer-in-charge. |
| 25 | 25 (a). Providing, fixing and testing following C.P. brass bath room and other fittings of approved quality with flange wherever applicable, etc. all complete as directed by Bank’s Engineer.Angular stop cock with wall flangeNote: - Basic rate of Angular stop cock is Rs. 940.00 each including GST. |
| 26 | 25 (b). Same as item 25 (a) above but for-Wash basin mixerNote: - Basic rate of Wash basin mixer is Rs. 2,775.00 each including GST. |
| 27 | 25 (c ). Same as item 25 (a) above but for-Regular body of Concealed stop cock and Exposed part kit of concealed stop cock with fitting sleeve, operating lever & adjustable wall flange Note: - Basic rate of Regular body of Concealed stop cock and Exposed part kit of concealed stop cock with fitting sleeve, operating lever & adjustable wall flange is Rs. 1,275.00 each including GST. |
| 28 | 25 (d). Same as item 25 (a) above but for-Bath room Wall mixer with provision for overhead showerNote: - Basic rate of Wall mixer with provision for overhead shower with 115 mm. long bend pipe on upper side, connecting legs & wall flanges is Rs. 4,987.00 each including GST. |
| 29 | 25 (e). Same as item 25 (a) above but for-Shower arm casted 190 mm. long flat shape for wall mounted showers with flange Note: - Basic rate of Shower arm casted 190 mm. long flat shape for wall mounted showers with flange is Rs. 825.00 each including GST. |
| 30 | 25 (f). Same as item 25 (a) above but for-Overhead shower Single Flow 100 mm. diameter (ABS CP) Note: - Basic rate of Overhead shower Single Flow 100 mm. diameter (ABS CP) is Rs. 1,162.00 each including GST. |
| 31 | 25 (g). Same as item 25 (a) above but for-Hand shower (health faucet) with 8 mm. diameter, 1.20 mt. long flexible tube & wall hookNote: - Basic rate of Hand shower (health faucet) with 8 mm. diameter, 1.20 mt. long flexible tube & wall hook is Rs. 1,293.00 each including GST. |
| 32 | 25 (h). Same as item 25 (a) above but for-2 Way bib cock with wall flange Note: - Basic rate of 2 Way bib cock with wall flange is Rs. 1,762.00 each including GST. |
| 33 | 26 (a). Providing, fixing and testing following bath room and other fittings of approved quality with flange wherever applicable, etc. all complete as directed by Bank’s Engineer.Single towel rail 600 m.m. long, Stainless Steel Note: - Basic rate of Single towel rail 600 m.m. long, Stainless Steel is Rs. 1,068.00 each including GST. |
| 34 | 26 (b). Same as item 26 (a) above but for-Towel ringNote: - Basic rate of Towel ring is Rs. 787.00 each including GST. |
| 35 | 26 (c). Same as item 26 (a) above but for-Soap dish holder Note: - Basic rate of Soap dish holder is Rs. 600.00 each excluding GST. |
| 36 | 26 (d). Same as item 26 (a) above but for-Tumbler holder Note: - Basic rate of Tumbler holder is Rs. 581.00 each including GST. |
| 37 | 26 (e). Same as item 26 (a) above but for-Glass shelf 600 mm. long Note: - Basic rate of Glass shelf 600 mm. long is Rs. 1,012.00 each including GST. |
| 38 | 26 (f). Same as item 26 (a) above but for-Corner glass shelf (with bracket) Note: - Basic rate of Corner glass shelf (with bracket) is Rs. 1,106.00 each including GST. |
| 39 | 27. Providing and fixing PVC moulded/ready made bath cabinet with attached mirror and shelves of approved make & model of size 300 mm. X 400 mm., etc. all complete as directed by Bank's Engineer. |
| 40 | 28. Providing and applying base coat of oil based cement primer of approved manufacture and two or more coats of textured paint of approved manufacturer and shade as per specifications to the interior surfaces of walls including surface preparation, applying putty, scrapping, scaffolding etc. all complete as directed by Bank’s Engineer and as per specifications. |
| 41 | 29. WOODEN STORAGE: - Full Ht. Storage:- ( Approx. size 7’4\\"x6' ) Providing & Placing in position 18\\"/24\\" deep box type cabinets made out 19 mm BWR plywood with glass 6 mm embedded and openable shutter, vertical & horizontal divisions/ partitions with all hardware (hinges, tower bolts, ss. handles, locks, magnetic catcher, etc.) of EBCO/ Hettich/ Godrej as per schedule of interiors, furniture & finishes. The back shall be made of 12mm plywood duly painted. All exposed edges shall be finished with polished (melamine) T.W. beading. All exposed surfaces & top must be finished with 1.00 mm high glossy laminate in two or more shades and all internal surface to be laminated with 0.8 mm mica as specified (Front elevation area will be measured for payment.) Complete in all respects as per direction of Engineer-in-Charge |
| 42 | 30. Wall fix dressing table with mirror & stool: - Providing & Placing in position 5' x 3'4\\" beveled edge mirror with ply backing made out 19 mm BWR plywood with one drawer and all hardware (hinges, tower bolts, ss. handles, locks, magnetic catcher, etc.) of EBCO/ Hettich/ Godrej as per schedule of interiors, furniture & finishes. The back shall be made of 12mm plywood duly painted. All exposed edges shall be finished with polished (melamine) T.W. beading. All exposed surfaces & top must be finished with 1.00 mm high glossy laminate in two or more shades and all internal surface to be laminated with 0.8 mm mica as specified complete in all respects as per direction of Engineer-in-Charge |
| 43 | 31. P/F Godrej make mortise lock or approved equivalent in SS Finish on main door |
| 44 | 32. P/F Godrej make mortise cylindrical lock or approved equivalent in SS Finish |
| 45 | 33. P/F SS Solid Body tower bolt of size one of 250 mm on back side |
| 46 | 34. P/F Wall mounted SS door buffer on back side of the door. |
| 47 | 35. Providing and fixing 30 mm thick flush door shutters of approved make conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters. The work includes providing and fixing 1.00 mm thick laminate of Greenlam Sherwood oak or of any other approved laminate having same specifications and same Basic rate as of Greenlam Sherwood oak on flush doors including adhesives, masking tape, cutting, wastage, approved adhesive masking etc complete in all respect(only door shutter to be measured for payment). |
| 48 | 36. Providing and fixing 2nd class teak wood wrought frame 100 mm. x 65 mm. to the door openings with 6 nos. hold fast made of 35 mm. x 5 mm. M.S. Flat 150 mm. long and embedded in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 20 mm. nominal size and down gauge) in blocks of size 200 mm. x 230 mm. x 150 mm. including painting of outer surface (which is contacted with walls) of frame with black japan, necessary shuttering, curing etc. all complete as directed by Bank's Engineer. The work includes providing and fixing 1.00 mm thick laminate of Greenlam Sherwood oak or of any other approved laminate having same specifications and same Basic rate as of Greenlam Sherwood oak on flush doors including adhesives, masking tape, cutting, wastage, approved adhesive masking etc complete in all respect. |
| 49 | 37. Removing/scraping/cleaning the existing wall surface, prepare even surface by using putty up to required level. Providing and applying a base coat of Interior cement primer of approved manufacture and two or more coats of acrylic emulsion paint having low VOC content of approved make and shade as per the manufacturers specifications to the interior surfaces of walls, ceilings, beams, columns, canopies, etc. The rate shall include for scaffolding, properly cleaning of the site after completion of the aforementioned work. The contractor is strictly advised to take all the safety measure for labour to carry out the work, etc. all completed as directed by Bank’s Engineer. |
| 50 | 38. Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.(Single / double glass panes, wire mesh and silicon sealant are included) Section Detail: Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of frame window shall be of approved manufacturer only and shall be made of frame /sash/mullion (if required) with appropriate profile size and wall thickness.Layout of the Window: Window shall be three track three panels sliding window. Window shall be glazed with 5.00 mm thick clear float glass for two panels and one shutter shall be fixed with Stainless steel 304 grade mosquito wire mesh. Supply and fixing of Premium quality handles and other required hardware fittings which are necessary for satisfactory performance of the UPVC window system are included in the work. Note: For uPVC (Alluplast/Finesta/Kommerling or equivalent as approved by competent authority) frame, sash and mullion extruded profiles, Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 51 | 39. Providing and fixing factory made uPVC white colour fixed glazed windows in washroom with 200 mm exhaust fan comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), 5.00 mm thick frosted glass , uPVC extruded glazing beads of appropriate dimension as per the thickness of glass, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. The work also includes P/F The UPVC window should have layout to fix exhaust fan in the UPVC window. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. The work should be completed in all respect including material (mentioned above), labour, sundries, CPOH, taxes etc. Fixed window single panel with S.S. friction hinges (350 x 19 x 1.9 mm) with one part of top fixed glass (frosted) and other having exhaust fan opening and bottom part with casement/shutter (with frosted glass). The UPVC window made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. Note: For uPVC (Alluplast/Finesta/Kommerling or equivalent as approved by competent authority) frame, sash and mullion extruded profiles, Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 52 | 40. Sliding Door for passageProviding and fixing ISI marked 25 mm. thick flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. The work includes providing required hardware fittings and both side lamination with sliding arrangement of Dorma/Ebco/Hettich or approved equivalent work also includes covering the sliding arrangement with palmet 19 mm thick panelling. |
| 53 | 41. Bathroom slider glass partition: - Providing & fixing of 8 mm toughened glass half fixed and half will sliding on proper sliders. All the required material and accessories details are as follows: - a. clear 8 mm toughened glass b. two aluminium adjustment wall profile in 1950 mm in chrome finish c. wall to wall aluminium top sliding channel in chrome finish d. steel ball bearing rollers encapsulated in brasse. round doorknob Note:1. The rate is inclusive of GST. 2. The firm is advised to visit the site and understand the site conditions before quoting the rates. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysNov 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender