Tender For Urgent Repairs To A-2-1, A-2-5 & A-3-1 B Type General Pool Quarters At Bhatlem.
Tender Value
11.50 Lakhs
Estimated cost
Bid Submission
12 Nov 2026
7 days left
EMD
23003
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
goa → Goa
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Urgent Repairs To A-2-1, A-2-5 & A-3-1 B Type General Pool Quarters At Bhatlem.
BOQ
| Sl. No. | Item Description |
| 1 | Repairs to plaster in patches of 2.5 sq.m. and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50m lead.;With cement mortar 1:4 (1 cement : 4 fine sand) |
| 2 | Removing old loose bottom or side cover of RCC slab beam columns etc. rubbing surface of concrete steel using wire brush and applying 2 coats of Alkaline rust converting primer (Feovert) after a waiting time of 6 hrs between coats and then applying another anti corrosive protective coating system ) for reinforcement bars (IPNet-RB) Conforms to IS-2770 Part-1 (Pull out Test) ASTM-3963-86 (Adhesion Test) and then applying concrete penetrating corrosion inhibitor (EPCO-KP100) and applying bonding new to old concrete (Epibond) Conforms to ASTM-C-882-87 and plastering on the fresh bond coat with Polymer Modified Mortar (Monobond) with 20mm C.M 1:3 and finishing coat of 6mm C.P 1:3 (1 Cement : 3 Sand ) incl. cost of transport etc. as per dir of EIC. All the chemicals will be of Krishna Conchem Products Pvt. Ltd. or Equivalent. |
| 3 | Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer over the plastered wall surface to prepare the surface even and smooth complete. |
| 4 | Removing dry or oil bound distemper by scrapping sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 5 | Distempering two or more coats with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade. |
| 6 | Providing water proofing treatment over the new R.C.C. roofs terrace toilet by spreading cement slurry over the R.C.C. slab and laying of 10cms. Average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba in covered with damp proof of Hindustan water proofing co. Or equivalent jointless water proofing plaster of mix 1:3 ( 1 cement : 3 find sand) finished smooth with wooden trowel with false marking of 30 cms square. The vertical surface of the adjoining walls are to be treated upto a height of 30cms including rounding of junction (the rate includes for complete items including labour and materials and including cost of initial treatment of roof slab as follows. The injunction of damp proof or equivalent compound with cement solution will be given as and when found necessary for filling honey comb cracks etc. in the R.C.C. slabs). NOTE: cement consumption 25 kg/sq.m. |
| 7 | UPVC ONLY DOOR FRAME:-;Providing & fixing Upvc Door Frame Yashashri make or equivalent made out of Upvc extruded multi cavity frame of 60 mm x 60mm x 2mm wall thickness. Frame is reinforced with G.I. Channel & welded in corners with Average weight 0.80 kg per running mtr. These frames are tested by using BS 2782 & DIN 53459 test methods. |
| 8 | 20 MM DOOR SHUTTER:-;Providing & fixing 20 mm door shutter Yashashri make or equivalent made by using 20mm x 155mm x 1.2mm upvc multi-cavity section and boarder of 30mm x 40mm x 2.5mm Upvc multi cavity section. The corners are joined by inserting polymetric corners & hardware used for fixing the door shutter is stainless steel hinges & S. S. handle & S.S. tower bolt. The average weight of 20mm door shutter is 4.60kg per sq mtr. These Upvc sections are tested by using BS 2782 & DIN 53459 test methods. |
| 9 | Providing & fixing bright finished brass 100 mm. mortice latch & lock & a pair of levers handles with necessary screws etc. complete (Indian make of approved quality). |
| 10 | Providing and fixing anodised aluminium shutters in accordance with the specification annexed herewith including transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Adjustable louvered windows.;Figured glass |
| 11 | Removing and refixing of door/ window shutters paneled or paneled and glazed including replacing of existing hionges chiseling etc complete as directed by Engineer - in - charge;Above 1 Sq.m area |
| 12 | Providing and fixing anodised aluminium shutters in accordance with the specification annexed herewith including transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Fixed windows/ ventilators matching with 4.5 mm series shutters.;Figured glass |
| 13 | Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section |
| 14 | Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by by screws.;Plain grill |
| 15 | Applying priming coat with ready mixed primer of approved brand and manufacture on steel work. |
| 16 | Applying priming coat with ready mixed primer of approved brand and manufacture on wood work complete. |
| 17 | Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for steel work of approved brand & manufacture in all shades on new work to give an even shade. |
| 18 | Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for wood work of approved brand & manufacture in all shades on new work to give an even shade. |
| 19 | Providing and fixing M.S. tower bolts (barrel type) with necessary screws etc. complete;250 x 10 mm |
| 20 | Providing and fixing M.S. handles with necessary screws etc. complete.;125 mm |
| 21 | Providing and fixing 150 mm. bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete. |
| 22 | Providing and fixing bright finished brass door latch with necessary screws etc complete;250 x 16 x 5 mm |
| 23 | Providing and fixing NICKEL chrome plated copper alloy Fancy BIB Cock Short Body Jaquar make or equivalent. Confirming to IS 8931;1993;15mm nominal bore |
| 24 | Providing and fixing NICKEL chrome plated copper alloy Fancy long body bib cock with wall flance Jaquar make or equivalent. Confirming to IS 8931;1993;15mm nominal bore |
| 25 | Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996.;500 lit. capacity |
| 26 | 18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge. |
| 27 | Crack filler for plasters IPS cement sand screeds and non - structural cracks. Do Not open the cracks Clean the cracks so as to free them from oil dust loose particles etc. Moisten the surface with water Fill cracks with EPCO - ACR using spatula or a putty knife. While applying avoid formation of cavity or bubbles. After filling allow the surface to dry for at least 24 hours. Apply in layers at 24 hours interval. If the depth of the crack is more than 10mm. incl. cost of scaffolding transport etc. as per dir of EIC. All the chemicals will be of Krishna Conchem Products Pvt. Ltd. or Equivalen. |
| 28 | An elastomeric cementitious waterproof coating for concrete and masonry.;Providing and applying on a well prepared vertical surface Masterseal 550EL of BASF make or equivalent elastomeric flexible two component polymers modified cementitious composite system that requires no addition of water at the site. The product shall be applied in minimum two coats to achieve total DFT of 1mm. The material shall be mixed and applied fully in accordance with the manufacturer's instructions. The product shall exhibit at least 40% elongation at ambient & 30% elongation in under water condition with tensile strength greater then 20 Kg/cm2. The product shall resist 1.5 bars pressure when tested as per DIN 1048 at 2mm DFT. When applied at 2mm DFT elastomeric coating shall be able to bridge crack up to 0.5mm width. All scaffolding ladders supporting materials etc. complete. Rates shall be inclusive of all labour materials tools and plant etc. complete. |
| 29 | Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 pipe).;25 mm outer dia CPVC pipe |
| 30 | Providing anti – termite treatment to buildings conforming to I.S.S. 6113 part II 1971 (revised) including adopting precautions for health hazards and safety measures as required therein with the cost of all materials chemicals plants equipments required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guaranty period complete. (The payment will be made on plinth of the building.;Post construction |
| 31 | Providing and fixing white vitereous china pedestal type (Europen type) water closet with seat as lid whth C.I. brass hinges and rubber fitings 15 lts white vitreous china low level flushing cistern with fittings as brackets 40 mm white precelain 3enameled flush bad 25 mm overflow pipe with specials and mosquito proof coupling of approved municipal design complete including cutting and making good the walls and floors where required.;W.C. pan with white plastic seat and lid |
| 32 | Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern 32 mm diameter M.I. or C.P. brass trap and union complete including cutting and making good the walls where required.;Flat back wash basin size 630 x 450mm with a pair of 15 mm C.P. brass pillar taps. |
| 33 | Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand ;4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement ;2 coarse sand :4 graded stone agrregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cemetn and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design.;Inside size 1.2m x 90 cm and 90cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter total weight of cover and frame to be not less than 116 kg. (weight of cover 58 kg). |
| 34 | Providing and fixing Hand Shower (Health Faucet) with 8mm dia ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards. |
| 35 | Providing and fixing 18 mm thick gang saw cut mirror polished premoulded and prepolished machine cut for kitchen platforms vanity counters window sills facias and similar locations of required size approved shade colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) joints treated with white cement mixed with matching pigment epoxy touch ups including rubbing curing moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade area of slab over 0.50 sqm;Jet Black |
| 36 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 including cutting of stone and making good the walls wherever required. Kitchen sink without drain board. with coupling & all accessories complete with choke stop strainer Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete.;Overall size 535mmx460mm (21\\"x18\\"\\") bowl size 460mmx380mmx200mm (18\\"\\"x 15\\"\\"x 8\\"\\") depth 200 mm. Glossy. 1.0mm thk.\\" |
| 37 | Providing and and laying Ceramic glazed floor tiles 300 x 300 (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in colours such as white ivory grey fume red brown laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc. complete |
| 38 | Providing and fixing vitrified antiskid tiles (320x320) and 10mm thick tiles in floor treads of steps landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete. |
| 39 | Providing and fixing coloured ceramic tiles (Bell or equivalent) of 8\\" x 12\\"\\" size and 6 mm thick in skirting and dados on 12 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) and jointed with cement slurry complete.\\" |
| 40 | Dismantling the tile work in floors and roofs laid in cement including stacking of materials within 50 meters lead for thickness of tiles 10mm to 25mm. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
TodayNov 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysNov 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender