Tender For Construction Of Civil & Hydro-Mechanical Works Of Arakot-Tiuni Hep (81 Mw) On The Pabar River In District Uttarkashi (Uttarakhand).
Tender Value
613.47 Crore
Estimated cost
Bid Submission
30 Nov 2026
20 days left
EMD
6.40 Crore
Bank guarantee accepted
Document Fee
1.18 Lakhs
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Uttar Kashi → Uttarakhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Civil & Hydro-Mechanical Works Of Arakot-Tiuni Hep (81 Mw) On The Pabar River In District Uttarkashi (Uttarakhand).
BOQ
| Sl. No. | Item Description |
| 1 | 1. CARE AND DIVERSION OF RIVER/ As per Technical Specification (SECTION B.8) |
| 2 | 1.1) Design and Construction of Coffer Dams (stage river diversion) along with maintainence, dismentalling, seepage control measures and dewatering etc. including cost of all materials, machinery, labour, complete in all respect as required for the construction of barrage and intake structure /As per Technical Specification. |
| 3 | 2. OPEN SURFACE EXCAVATION (including cost of dewatering)/ As per Technical Specification (SECTION B.2 ) |
| 4 | 2.1) Common Excavation in all classes of soil, soft rock/ As per Technical Specification (2.3.1/2.4.3/2.10.1/2.10.3) |
| 5 | 2.2) Hard Rock Excavation requiring blasting /As per Technical Specification (2.3.2/2.4.4/2.10.1/2.10.4) |
| 6 | 2.3) Dental excavation/ As per Technical Specification (2.3.3/2.4.5/2.10.1/2.10.7) |
| 7 | 3. UNDER GROUND EXCAVATION in all classes of rocks/ As per Technical Specification (SECTION B.1 & B.3 ) |
| 8 | 3.1) Excavation in Adits, Intake tunnel, SFT, HRT, TRT, Horizontal/ near horizontal tunnels/ As per Technical Specification (3.8.6, 3.15.2) |
| 9 | 3.2) Excavation in Desilting Chambers including Silt Flushing Duct/ As per Technical Specification (3.8.7, 3.15.4) |
| 10 | 3.3) Excavation in Surge Shaft, Pressure Shaft, Shafts/ As per Technical Specification (3.15.3 |
| 11 | 4. ROCK SUPPORTS FOR OPEN SURFACE WORKS / As per Technical Specification (SECTION B.4 |
| 12 | 4.1) Rock anchors (25mm dia.) cement grouted including cost of drilling holes, grouting materials, other materials, labour, T&P completed in all respect / As per Technical Specification (4.5.2/4.10.1/4.10.2) |
| 13 | 4.1.1) Length up to 6 m |
| 14 | 4.1.2) Length more than 6 m |
| 15 | 4.2) Rock anchors (32mm dia.) cement grouted including cost of drilling holes, grouting materials, other materials, labour, T&P completed in all respect / As per Technical Specification (4.5.2/4.10.1/4.10.2) |
| 16 | 4.2.1) Length up to 6 m |
| 17 | 4.2.2) Length more than 6 m |
| 18 | 4.3) Rock bolts (Resin end anchorage and cement grouted) 25mm dia including cost of drilling holes, resin & grouting materials, other materials, labour, T&P, completed in all respect/ As per Technical Specification (4.5.3/4.10.1/4.10.2) |
| 19 | 4.3.1) Length up to 6 m |
| 20 | 4.3.2) Length more than 6 m |
| 21 | 4.4) Rock bolts (Resin end anchorage and cement grouted) 32mm dia including cost of drilling holes, resin & grouting materials, other materials, labour, T&P, completed in all respect/ As per Technical Specification (4.5.3/4.5.4/4.10.1/4.10.2) |
| 22 | 4.4.1) Length up to 6 m |
| 23 | 4.4.2) Length more than 6 m |
| 24 | 4.5) Rock Bolt / Rock Anchor Extensions reinforcement bars into Concrete (4.5.7/4.10.2) |
| 25 | 4.6) Cable anchors/ tendons 25MT capacity including cost of drilling holes, grouting materials, other materials, labour, T&P completed in all respect/ As per Technical Specification (4.6, 4.10.3) |
| 26 | 4.6.1) upto 20 m long |
| 27 | 4.6.2) above 20 m long |
| 28 | 4.7) Chain link fabric / As per Technical Specification (4.7.1/4.10.4.1) |
| 29 | 4.8) Welded wire mesh / As per Technical Specification (4.7.2/4.10.4.2) |
| 30 | 5. ROCK SUPPORTS FOR UNDERGROUND WORKS/ As per Technical Specification (SECTION B.4 ) |
| 31 | 5.1) Rock anchors (25mm dia.) cement grouted including cost of drilling holes, grouting materials, other materials, labour, T&P completed in all respect/ As per Technical Specification (4.5.2/4.10.1/4.10.2) |
| 32 | 5.1.1) Length up to 6 m |
| 33 | 5.1.2) Length more than 6 m |
| 34 | 5.2) Rock anchors (32mm dia.) cement grouted including cost of drilling holes, grouting materials, other materials, labour, T&P completed in all respect/ As per Technical Specification (4.5.2/4.10.1/4.10.2) |
| 35 | 5.2.1) Length up to 6 m |
| 36 | 5.2.2) Length more than 6 m |
| 37 | 5.3) Rock bolts (25mm dia)( Resin end anchorage and cement grouted) including cost of drilling holes, resin & grouting materials, other materials, labour, T&P, completed in all respect/ As per Technical Specification (4.5.3/4.5.4/4.10.1/4.10.2) |
| 38 | 5.3.1) Length up to 6 m |
| 39 | 5.3.2) Length more than 6 m |
| 40 | 5.4) Rock bolts (32mm dia) (Resin end anchorage and cement grouted) including cost of drilling holes, resin & grouting materials, other materials, labour, T&P, completed in all respect/ As per Technical Specification (4.5.3/4.10.1/4.10.2) |
| 41 | 5.4.1) Length up to 6 m |
| 42 | 5.4.2) Length more than 6 m |
| 43 | 5.5) Rock Bolt/ Rock Anchor Extensions reinforcement bars into Concrete (4.5.7/4.10.2) |
| 44 | 5.6) Self Drilling Anchor R25 including cost of drilling holes, grouting materials, other materials, labour, T&P completed in all respect/ As per Technical Specification (4.5.8/4.10.1/4.10.2) |
| 45 | 5.6.1) Length up to 6 m |
| 46 | 5.6.2) Length more than 6 m |
| 47 | 5.7) Self Drilling Anchor R32 including cost of drilling holes, grouting materials, other materials, labour, T&P completed in all respect/ As per Technical Specification (4.5.8/4.10.1/4.10.2) |
| 48 | 5.7.1) Length up to 6 m |
| 49 | 5.7.2) Length more than 6 m |
| 50 | 5.8) Chain link fabric/ As per Technical Specification (4.7.1/4.10.4.1) |
| 51 | 5.9) Welded wire mesh/ As per Technical Specification (4.7.2/4.10.4.2) |
| 52 | 5.10) Permanent Steel support by Steel Ribs in all type of underground works / As per Technical Specification (4.8/4.10.5.1) |
| 53 | 5.11) Permanent Steel support by Lattice Girders (shotcrete to be paid separately)/ As per Technical Specification (4.8.2/4.10.5.1) |
| 54 | 5.12) Steel Lagging/ As per Technical Specification (4.8.4/4.10.5.2) |
| 55 | 5.13) Precast Reinforced Concrete lagging/ As per Technical Specification (4.8.4/4.10.5.2) |
| 56 | 5.14) Forepoling using Reinforcement Bars/ As per Technical Specification (4.9.1/4.10.6) |
| 57 | 5.15) Pipe Roofing using Structural Steel/ As per Technical Specification (4.9.2/4.10.6.3) |
| 58 | 5.15.1) 50 Dia. Medium MS pipe |
| 59 | 5.15.2) 75 Dia. Medium MS pipe |
| 60 | 5.16) Cable anchors/ tendons 25MT capacity upto 20 m long including cost of drilling holes, grouting materials, other materials, labour, T&P, completed in all respect/ As per Technical Specification (4.6, 4.10.3) |
| 61 | 6. SHOTCRETE including cost of all materials, labour, T&P, completed in all respect/ As per Technical Specification (B.5) |
| 62 | 6.1) OPEN/SURFACE WORKS |
| 63 | 6.1.1) Plain shotcrete (wiremesh to be paid separately)/ As per Technical Specification(5.1 to 5.17) |
| 64 | 6.1.2) Steel fibre reinforced shotcrete (SFRS) including steel fibre/ As per Technical Specification (5.1 to 5.17) |
| 65 | 6.2) UNDERGROUND WORKS |
| 66 | 6.2.1) Plain shotcrete (wiremesh to be paid separately)/ As per Technical Specification (5.1 to 5.17) |
| 67 | 6.2.2) Steel fibre reinforced shotcrete (SFRS) including steel fibre/ As per Technical Specification (5.1 to 5.17) |
| 68 | 6.3) Guniting (1bag=50kg of cement/ As per Technical Specification (5.11, 5.17.1.8) |
| 69 | 7. FILL, BACKFILL, RIPRAP AND PITCHING/ As per Technical Specification (SECTION B.6) |
| 70 | 7.1) Random backfill including cost of backfill materials, labour and T&P complete in all respect/ As per Technical Specification (6.3/6.10/6.11) |
| 71 | 7.2) Compacted backfill including cost of backfill materials, compaction in layers, labour and T&P complete in all respect/ As per Technical Specification (6.3/6.10/6.11) |
| 72 | 7.3) Free-Draining backfill including cost of backfill materials, labour, compaction in layers and T&P complete in all respect/ As per Technical Specification (6.2/6.10/6.11) |
| 73 | 7.4) Graded/ Inverted Filter including cost of filter materials, labour and T&P complete in all respect/ As per Technical Specification (6.5/6.10/6.11) |
| 74 | 7.5) Stone pitching/ As per Technical Specification (6.6/6.10/6.11) |
| 75 | 8. DRILLING AND GROUTING /As per Technical Specification (SECTION B.7) |
| 76 | 8.1) Drilling for Contact/ consolidation grouting including all material, labour and T&P complete in all respect/ As per Technical Specification (7.8.2.1/7.9.1/7.9.2/7.9.3/7.9.4/7.9.5/7.9.6) |
| 77 | 8.2) Shifting of Equipments for Grouting operation for contact/consolidation grouting including labour and T&P complete in all respect/ As per Technical Specification (7.8.2.1/7.9.1/7.9.2/7.9.3/7.9.4/7.9.5/7.9.6) |
| 78 | 8.3) Grouting materials for contact & consolidation including cost of cement, sand, admixtures, micro/ultra fine cement and bentonite as per design mix/ As per Technical Specification (7.6/7.7/7.9.1/7.9.6) (1 Bag = 50kg of Cement) |
| 79 | 8.3.1) Using Cement & Admixture |
| 80 | 8.3.2) Using Cement , sand/ bentonite & admixtures |
| 81 | 8.3.3) Using Micro/ Ultrafine Cement |
| 82 | 8.4) Drilling of drainage hole/ probe hole 76 mm dia. including all material, labour and T&P complete in all respect /As per Technical Specification (7.8.2.1/7.9.9) |
| 83 | 8.5) Drilling of drainage hole/ probe hole 38 mm dia. including all material, labour and T&P complete in all respect/ As per Technical Specification (7.8.2.1/7.9.9) |
| 84 | 8.6) Perforated PVC pipes 50 mm dia. including all material, labour and T&P complete in all respect for drainage |
| 85 | 8.7) Drilling of Exploratory Holes/ Instrumentation/ Check holes etc. including all material, labour and T&P complete in all respect/ As per Technical Specification (7.8.2.2) |
| 86 | 8.7.1) Drilling Nx/Hx size exploratory hole with core recovery including all material, labour and T&P complete in all respect/ As per Technical Specification (7.8.2.2/7.9.10) |
| 87 | 8.7.2) Drilling Nx/Hx size exploratory hole without core recovery/ As per Technical Specification (7.8.2.2/7.9.10) |
| 88 | 8.7.3) Water Pressure testing in drill holes/ As per Technical Specification (7.8.2.2/7.9.10) |
| 89 | 8.8) Embedded pipes & fittings including all material, labour and T&P complete in all respect/ As per Technical Specification (7.4.4/7.9.13) |
| 90 | 9. PERMEATION GROUTING (SEEPAGE CUT-OFF WORKS)/ As per Technical Specification (SECTION B.19) |
| 91 | 9.1) Drilling 136-172 mm dia holes by rotary/ odex/ percussion drilling including cost of all materials, labour,T&P etc in all respect for proper completion of work/ As per Technical Specification Item (19.4.4/19.5.1) |
| 92 | 9.2) Supply and installation of TAM pipe/ perforated grout casing pipe of internal dia 45-65 mm including cost of all material, labour, T&P etc in all respect for proper completion of work/ As per Technical Specification (19.4.8/19.5.1) |
| 93 | 9.3) Shifting of Equipments for Grouting operation for contact/ consolidation grouting including labour and T&P complete in all respect/ As per Technical Specification (7.8.2.1/7.9.1/7.9.2/7.9.3/7.9.4/7.9.5/7.9.6) |
| 94 | 9.4) Permeation Grouting to attain the desired lugeon value including cost of cement and all material, labour, equipment, T&P etc in all respect but excluding cost of drilling, cost of TAM pipe and shifting operation cost of equipments (1 Bag = 50kg of Cement)/ As per Technical Specification (19.4.7/19.5.1) |
| 95 | 9.4.1) Using Cement & admixers |
| 96 | 9.4.2) Using Cement , sand/ bentonite & admixtures |
| 97 | 9.4.3) Using Micro/ Ultrafine Cement |
| 98 | 10. CONCRETE WORK including cost of dewatering, formwork , cement, aggregates (fine & coarse), admixtures, micro/ultra fine cement, air entraining agent, super plasticizer and bentonite as per design mix etc./ As per Technical Specification (SECTION B.9) |
| 99 | 10.1) Concrete for open surface works |
| 100 | 10.1.1) Concrete of grade M15 A40 /As per Technical Specification (9.5/ 9.16.1/ 9.16.2/ 9.17) |
| 101 | 10.1.2) Concrete of grade M15 A20 / As per Technical Specification (9.5/ 9.16.1/ 9.16.2/ 9.17) |
| 102 | 10.1.3) Concreting of grade M20 A40 /As per Technical Specification (9.5/ 9.16.1/ 9.16.2/ 9.17) |
| 103 | 10.1.4) Concrete of grade M20 A20 /As per Technical Specification (9.5/ 9.16.1/ 9.16.2 / 9.17) |
| 104 | 10.1.5) Concrete of grade M25 A40 /As per Technical Specification (9.5/ 9.16.1/ 9.16.2/ 9.17) |
| 105 | 10.1.6) Concrete of grade M25 A20 /As per Technical Specification (9.5/ 9.16.1/ 9.16.2/ 9.17) |
| 106 | 10.1.7) Concrete of grade M30 A20 /As per Technical Specification (9.5/ 9.16.1/ 9.16.2/ 9.16.10/ 9.17.1/ 9.17.7) |
| 107 | 10.1.8) Concrete Blocks M15 A40/ As per Technical Specifications (16.7, 16.9.8) |
| 108 | 10.1.8.1) In-situ concrete blocks |
| 109 | 10.1.8.2) Pre-cast concrete blocks including transporting and laying at site |
| 110 | 10.1.8.3) Cobble Filling 150mm in size in between CC blocks/ As per technical Specification |
| 111 | 10.1.9) High performance concrete (HPC) M60/ As per Technical Specification (9.5/9.5.2/9.17.2) |
| 112 | 10.1.10) Self Compacted Concrete (SCC) M35 A10/ As per Technical Specification (9.5, 9.17) |
| 113 | 10.1.11) Porous concrete/ As per Technical Specification (9.16.14/9.17.1/9.17.16) |
| 114 | 10.1.12) Plums(stone) for embedding in concrete including cost of stones,labour and T&P (cost of concrete to be paid separately as per design mix)/ As per Technical Specification (9.17.15) |
| 115 | 10.1.13) Epoxy Grouting of Equipment Bearing Plates/ As per Technical Specification (9.17.8) |
| 116 | 10.1.14) Non-Shrink cement Grouting of Equipment Bearing Plates/ As per Technical Specification (9.17.8) |
| 117 | 10.2) Concrete for underground works |
| 118 | 10.2.1) Concrete of grade M15 A40 / As per Technical Specification (9.5/9.16.1/9.16.2/9.17) |
| 119 | 10.2.2) Concrete of grade M15 A20 / As per Technical Specification (9.5/9.16.1/9.16.2/9.17) |
| 120 | 10.2.3) Concreting of grade M20 A40 / As per Technical Specification (9.5/9.16.1/9.16.2/9.17) |
| 121 | 10.2.4) Concrete of grade M20 A20 / As per Technical Specification (9.5/9.16.1/9.16.2/9.17) |
| 122 | 10.2.5) Concrete of grade M25 A40 / As per Technical Specification (9.5/9.16.1/9.16.2/9.17) |
| 123 | 10.2.6) Concrete of grade M25 A20 / As per Technical Specification (9.5/9.16.1/9.16.2/9.17) |
| 124 | 10.2.7) Self Compacted Concrete (SCC) M35 A10/ As per Technical Specification (9.5, 9.16, 9.17) |
| 125 | 11. REINFORCING STEEL /As per Technical Specification (SECTION B.11) |
| 126 | 11.1) Providing, fabricating and placing in position HYSD reinforcement steel for RCC works including cleaning, straightening, cutting, bending, hooking, lapping, binding with 1.25mm diameter annealed steel wire, welding wherever required, including cost of all materials, machinery, labour, complete and as directed with all leads and lifts/ As per Technical Specification (11/11.12) |
| 127 | 11.2) Providing and fixing Couplers of 32mm dia and more including cost of all materials,labour,T&P etc for proper completion of work/ As per Technical Specification (11.7/11.12) |
| 128 | 12. WATERSTOPS including cost of all materials, labour, T&P, completed in all respect/ As per Technical Specification (SECTION B.12) |
| 129 | 12.1) PVC water stops 300 mm wide/ As per Technical Specification (12.5.1/12.7) |
| 130 | 12.2) PVC water stops 150mm wide/ As per Technical Specification (12.5.1/12.7) |
| 131 | 12.3) Bituminous coating/ As per Technical Specification (12.5.5/12.7) |
| 132 | 12.4) Joint Filler/ mastic board/ As per Technical Specification (12.5.3/12.7) |
| 133 | 13. METAL WORKS including cost of all materials, labour, T&P, completed in all respect/ As per Technical Specification (SECTION B.13) |
| 134 | 13.1) Embedded Metal Works, Miscellaneous steel sections including pipes, frames, gratings, covers,climbing irons (rungs), liner, Steel Covers, Frames, and Gratings etc / As per Technical Specification (13.7.2/13.7.3/13.7.6/13.9.3/13.9.4/13.9.6) |
| 135 | 13.2) Hand rails/ Railing / Ladders / As per Technical Specification (13.7.4/13.7.5/13.7.6/13.9.5/13.9.6) |
| 136 | 13.3) Furnishing and installation of 1200mm high, 50mm dia stainless steel hand railing on top slab of structure and painting the railing as per technical specifications and drawing or as directed by Engineer- in-Charge including cost of all material, Tools and Plants(T&P) and accessories, and labour etc complete in all respect / As per Technical Specification (13.7.5, 13.9.5) |
| 137 | 13.4) Erection of Metal works supplied by others / As per Technical Specification (13.8/13.9.10) |
| 138 | 14. MISCELLANEOUS AND ANCILLARY WORKS, SLOPE PROTECTION including cost of all materials, labour, T&P, completed in all respect/ As per Technical Specification (SECTION B.15 & B16) |
| 139 | 14.1) Gabions/Wire crate with boulders filling / As per Technical Specification (16.3/16.8.2/16.8.3) |
| 140 | 14.2) PVC pipes including all labour and T&P required for proper completion/ As per Technical Specification (15.5/15.7.5) |
| 141 | 14.2.1) 75mm nominal dia./ As per Technical Specification (15.5/15.7.5) |
| 142 | 14.2.2) 100mm nominal dia./ As per Technical Specification (15.5/15.7.5) |
| 143 | 14.2.3) 150mm nominal dia./ As per Technical Specification (15.5/15.7.5) |
| 144 | 14.3) Providing and laying in position of RCC pre-cast Hume pipes 600 mm internal dia./ As per technical specifications (15.3, 15.7.3) |
| 145 | 14.4) Random rubble masonry (wet) in 1:4 CM/ As per Technical Specification (16.4.1/16.8.4) |
| 146 | 14.5) Random rubble masonry (dry)/ As per Technical Specification (16.4.2/16.8.5) |
| 147 | 14.6) Brick work in 1:4 cement mortar including cost of all material, curing, tools, plants and accessories, labour etc complete in all respect/ As per Technical Specification (14.5/14.16) |
| 148 | 14.7) Plastering of brick wall 20mm thick Cement sand mortar (1:3) as per technical specifications and drawings including cost of all materials, curing, tools & plants & accessories, scaffolding and labour etc complete in all respect.As per Technical Specification (14.6, 14.16) |
| 149 | 14.8) Design, Supply, fabrication, erection, welding, testing and commissioning of steel liner plate in pressure shaft and surge shaft orifice and transitions including cost of all materials, machinery, labour, complete and as directed with all leads and lifts/ As per Technical Specification (B.20) |
| 150 | 14.9) Grass Turfing/ As per Technical Specifications (16.6, 16.9.7) |
| 151 | 14.10) Soil Nailing (25 Dia, 6m long @ 1.5 m C/C)/ As per technical specifications (16.9, 16.10) |
| 152 | 14.11) Cementious Composite Geo-Synthtic carpet (CCGC) 8mm thick/ As per technical specifications (16.8, 16.9.9) |
| 153 | 14.12) Fencing and Gates/ As per technical Specifications (15.2, 15.7.2) |
| 154 | 14.13) Security huts each of 10 sqm in plan/ As per Technical Specifications (B.14) |
| 155 | 14.14) Spreading of 400 mm thick Stone Ballast in Switch yard Area |
| 156 | 14.15) Construction of control room building/ As per Technical Specifications (B.14) |
| 157 | 14.16) Archtectural works - Miscellaneous Works ( PH & Control room building works, flooring, ceiling doors, windows, shutters, illumination system, water and sanitary fitting, etc as approved by Engineer-in-charge)/ As per Technical Specifications (B.14) |
| 158 | 14.17) Suspended Ceiling in control room/ conference room/ office/ As per Technical Specifications (14.8, 14.16) |
| 159 | 14.18) Wall panelling in control room/ conference room/ office/ As per Technical Specifications (14.13, 14.16) |
| 160 | 15. Instrumentation for Monitoring including cost of all materials, labour, T&P, completed in all respect/ As per Technical Specifications (SECTION B.17) |
| 161 | 15.1) Instrumentation for open surface works/ As per Technical Specification (SECTION B.17) |
| 162 | 15.1.1) Surface Settlement Points |
| 163 | 15.1.2) Pore Pressure Gauges (Piezometers) |
| 164 | 15.1.3) Triaxial Joint Meter |
| 165 | 15.1.4) Stress Meter |
| 166 | 15.1.5) Uplift pressure cells |
| 167 | 15.1.6) Instrumentation Cables |
| 168 | 15.1.6.1) 4-core Cable |
| 169 | 15.1.6.2) 10-core Cable |
| 170 | 15.1.7) 10 way Junction cum switch box (SB) |
| 171 | 15.1.8) Automatic Data acquisition System (DAS) |
| 172 | 15.1.9) Automatic Weather Station |
| 173 | 15.1.10) Water level measuring painted gauge |
| 174 | 15.1.11) Strong Motion Accelerograph |
| 175 | 15.2 Instrumentation for underground works/ As per Technical Specification (SECTION B.17) |
| 176 | 15.2.1) Bi-Reflex Paper target points along with break off point & 500 mm long 3D monitoring bolt |
| 177 | 15.2.2) Topographical markers/Survey Points |
| 178 | 15.2.3) Vibrating wire type Load Cells Measuring Range: 30 T Over Range Limit: 150% with 20m cable |
| 179 | 15.2.4) Supply, installation and monnitoring by SM Vibrating wire strain gauge |
| 180 | 15.2.5) Supply, installation and monnitoring by PC pressure cells |
| 181 | 15.2.6) Supply, installation and monnitoring by Piezometer |
| 182 | 16. Tunnel Hazard works/ As per Technical Specification (SECTION B.3 ). |
| 183 | 16.1) Placing in position of sand bags including supplying sand and filling the same in empty bags and tying with contractors binding wire, leading to tunnel site with contractors men, material, consumables, tools and plants, equipments, machIneries, including all lead and lift, loading, unloading etc. complete (filling sand bag of weight 50 Kg shall be counted as 01 number) |
| 184 | 16.2) Removal of sand bags, when not required and disposal thereof with contractors men, material, consumables, tools and plants, equipments, machineries, including all lead and lift, loading, unloading etc. complete.(filling sand bag of weight 50 Kg shall be counted as 01 number) |
| 185 | 16.3) Supply ,manufacture and erection in position of temporary supports/ struts in hazardous position. Note : On removal of temporary supports,released structural steel will be property of contractor |
| 186 | 16.4) Dismantlling of existing permanent/ temporary supports and leading the cut supports to contractor's store/ depot etc with contractor's men,material, consumables, tools & plants, equipments, machineries, including all lead & lifts, loading, unloading, etc complete |
| 187 | RADIAL GATES WITH HYDRAULIC HOIST |
| 188 | Radial gate for a clear opening size of 18.5 m (W) x 14.3 m (H) complete with skin plate, horizontal girders, vertical stiffeners, inclined arms, bracings, trunnion assemblies, guide rollers, lifting brackets, anchors, trunnion brackets, dogging arrangement, access ladder with hand railing and safety cage, walkway platform between piers etc. complete in all respect as per scope of works and technical specifications. |
| 189 | Radial gate with flap gate for a clear opening size of 18.5 m (W) x 14.3 m (H) including flap gate of size 10.0 m (W) x 2.0 m (H) complete with skin plate, horizontal girders, vertical stiffeners, inclined arms, bracings, trunnion assemblies, guide rollers, seals & seal seat for flap gate, Rubber seals assemblies for flap gate, lifting brackets, anchors, trunnion brackets, dogging arrangement, access ladder with hand railing and safety cage, walkway platform between piers etc. complete in all respect as per scope of works and technical specifications. |
| 190 | First stage embedded parts (anchors) in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure etc. complete in all respect as per scope of works and technical specifications. |
| 191 | Second stage embedded parts complete with sill beam, wall plates, top seal seat with anchor bolts, nuts & washers and full-length anchors for trunnion brackets, anchors for steel support beam for hoist, etc. complete in all respect as per scope of works and technical specifications. |
| 192 | Single acting twin cylinders hydraulic hoist of adequate stroke/capacity including all the accessories such as cylinder support steel beam with bracket and connecting pin, self-lubricating bearing for either ends, gate position indicator and sensor/limit switches for operation of radial gates and other associated components required for the erection and commissioning etc. complete in all respect as per scope of works and technical specifications. |
| 193 | Independent hydraulic power pack assembly & control system including oil tank, hydraulic oil, seamless piping between power pack and cylinders and pipe fittings/ supports and other accessories like flexible pressure hoses, pipe connectors, ball valves, heavy duty pipe clamps, lighting and other fittings etc. complete in all respects for operation of hydraulic hoists as per scope of works and technical specifications. |
| 194 | Double acting twin cylinders hydraulic hoist of adequate stroke/capacity including all the accessories, hydraulic power pack & control system for smooth operation of flap gate including motor, pump, control panel, seamless piping, pressure gauges, flow control valves, pressure switches etc. with controls, manual controls, limit switches and other fittings etc. complete in all respect as per scope of works and technical specifications. |
| 195 | Local electrical control panel for each hoist including all components, instruments, enclosure, ducts, cabling between local control panel & hydraulic power pack, etc. complete in all respects for operation of Hydraulic Power Pack as per scope of works and technical specifications. |
| 196 | Rubber seals (bottom and sides etc.) assemblies complete in all respect as per scope of works and technical specifications. |
| 197 | Trolley mounted (mobile) gasoline engine complete with control and accessories complete in all respect as per scope of works and technical specifications. |
| 198 | Hydraulic oil filtering unit complete with all accessories, equipment, instruments etc. complete in all respect as per scope of works and technical specifications. |
| 199 | Low vacuum dehydration and degasification unit complete with control and accessories including One (01) unit of contamination checking kit complete in all respect as per scope of works and technical specifications. |
| 200 | Mandatory Spare parts in accordance with clause 1.9 of Particular Technical Specifications. |
| 201 | STOPLOG GATE WITH GANTRY CRANE AND LIFTING BEAM |
| 202 | Stop log units of vertical lift fixed wheel type for a clear opening size of 18.5 m (W) x 14.3 m (H) complete with skin plate, stiffeners, horizontal girders, end vertical girders, sliding pads, guide rollers, lifting & latching arrangement, filling valves in top unit, etc. complete in all respect as per scope of works and technical specifications. |
| 203 | First stage embedded parts (anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate for gate groove and first stage embedded parts (anchors) for storage pit as per requirement complete in all respect as per scope of works and technical specifications. |
| 204 | Second stage embedded parts such as sill beam, slide tracks & side seal seats, side guides, top seal seat, anchor bolts, nuts & washers, support angles, latching and storage arrangement over the piers. Embedded parts and ladder for storage pit with steel grating for stoplog units etc. complete in all respect as per scope of works and technical specifications. |
| 205 | Lifting beam of adequate capacity with automatic engaging / disengaging device complete with frame, guides, pulleys, bearings, counterweight and other accessories, etc. complete in all respect as per scope of works and technical specifications. |
| 206 | Electrically operated travelling gantry crane with cross-travel arrangement of adequate capacity, cabin operated along with necessary structural, mechanical and electrical control equipment including gantry track rails extended up to parking, embedded parts, end stoppers, counterweight, etc. and other accessories complete in all respects for safe operation of spillway stoplogs units as per scope of works and technical specifications. |
| 207 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 208 | Mandatory Spare parts in accordance with the clause 2.9 of Particular Technical Specifications. |
| 209 | INTAKE BULKHEAD GATE WITH ROPE DRUM HOIST |
| 210 | Vertical lift fixed wheel type Intake Bulkhead Gate for a clear opening size of 3.82 m (W) x 6.0 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels, filling valve etc. complete in all respect as per scope of works and technical specifications. |
| 211 | First stage embedded parts (anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 212 | Second stage embedded parts complete with sill beam, seal seats, Side Guides, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 213 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 214 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 215 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 216 | Mandatory Spare parts in accordance with clause 3.9 of Particular Technical Specifications. |
| 217 | INTAKE SERVICE GATE WITH ROPE DRUM HOIST |
| 218 | Vertical lift fixed wheel type Intake Service Gate for a clear opening size of 3.82 m (W) x 6.0 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels etc. complete in all respect as per scope of works and technical specifications. |
| 219 | First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 220 | Second stage embedded parts complete with sill beam, seal seats, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 221 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 222 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 223 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 224 | Mandatory Spare parts in accordance with clause 4.9 of Particular Technical Specifications. |
| 225 | INTAKE HRT GATE WITH ROPE DRUM HOIST |
| 226 | Vertical lift fixed wheel type Intake HRT Gate for a clear opening size of 3.82 m (W) x 4.60 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels, filling valve etc. complete in all respect as per scope of works and technical specifications. |
| 227 | First stage embedded parts (anchors), etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 228 | Second stage embedded parts complete with sill beam, seal seats, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 229 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 230 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 231 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 232 | Mandatory Spare parts in accordance with clause 5.9 of Particular Technical Specifications. |
| 233 | INTAKE TRASH RACK AND TRCM |
| 234 | Trash racks suitable for each opening of intake structure 7.2 m (W) x 11.68 m (H) (inclined height) size complete in all respect as per scope of works and technical specifications. |
| 235 | First stage inserts and embedded parts, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts, pipes for sensors etc. complete in all respect as per scope of works and technical specifications. |
| 236 | Second stage embedded parts complete with guides, bottom base, etc complete in all respect. as per scope of works and technical specifications. |
| 237 | Automatically engaging / disengaging type lifting beam with two positively engaging & disengaging type hooks by means of counter weight & lever mechanism etc. for handling of trash rack panels complete in all respect.as per scope of works and technical specifications. |
| 238 | Hydraulically operated Semi-automatic trash rack cleaning machine complete in all respect along with bucket, control devices, rails and fixtures, grapple hoist, cable reeling drum along with tool kits etc. complete in all respect as per scope of works and technical specifications. |
| 239 | Mandatory Spare parts in accordance with clause 6.9 of Particular Technical Specifications. |
| 240 | ADIT PLUG GATE |
| 241 | HRT Adit plug Hinge type gate for a clear opening of 2.5 m (W) x 2.5 m (H) with skin plate, horizontal girders, vertical stiffeners and end verticals and locking, wire rope pulling machine to operate the hinge gate etc. complete in all respect as per scope of works and technical specifications. |
| 242 | First and second stage embedded parts such as bottom and top seal seats, side seal seat cum bearing plate, anchor bolts, nuts & washers, erection hooks etc. for hinged gate complete in all respect. as per scope of works and technical specifications. |
| 243 | Rubber seals assemblies complete in all respect as per scope of works and technical specifications. |
| 244 | Mandatory Spare parts in accordance with clause 7.9 of Particular Technical Specifications. |
| 245 | SURGE SHAFT GATES WITH ROPE DRUM HOIST |
| 246 | Vertical lift fixed wheel type Surge shaft gates for a clear opening of 2.6 m (W) x 3.3 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement and filling valves etc. complete in all respect as per scope of works and technical specifications. |
| 247 | First stage embedded parts (anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles complete in all respect as per scope of works and technical specifications. |
| 248 | Second stage embedded parts such as sill beam, seal seats, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 249 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 250 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 251 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 252 | Mandatory Spare parts in accordance with clause 8.9 of Particular Technical Specifications. |
| 253 | DRAFT TUBE GATES WITH ROPE DRUM HOIST |
| 254 | Vertical lift fixed wheel type Draft tube gates for a clear opening of 3.6 m (W) x 1.9 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement and filling valves etc. complete in all respect as per scope of works and technical specifications. |
| 255 | First stage embedded parts(anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles complete in all respect as per scope of works and technical specifications. |
| 256 | Second stage embedded parts such as sill beam, roller tracks and side seal seats, guides, seal seat, anchor bolts, nuts & washers etc complete in all respect as per scope of works and technical specifications. |
| 257 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 258 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect. |
| 259 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 260 | Mandatory Spare parts in accordance with clause 9.9 of Particular Technical Specifications. |
| 261 | TAIL RACE TUNNEL GATE WITH ROPE DRUM HOIST |
| 262 | Vertical lift fixed wheel type Tail Race Tunnel Gate for a clear opening size of 6.0 m (W) x 4.0 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels, filling valve etc. complete in all respect as per scope of works and technical specifications. |
| 263 | First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 264 | Second stage embedded parts complete with sill beam, seal seats, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 265 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 266 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 267 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 268 | Mandatory Spare parts in accordance with clause 10.9 of Particular Technical Specifications. |
| 269 | FISH LADDER EMERGENCY GATE WITH SCREW ROD HOIST |
| 270 | Slide type Fish ladder emergency gate for a clear opening of 0.5 m (W) x 0.7 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement etc. complete in all respect as per scope of works and technical specifications. |
| 271 | First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles etc. complete in all respect as per scope of works and technical specifications. |
| 272 | Second stage embedded parts such as sill beam, seal seats, guides, anchor bolts, nuts & washers etc. complete in all respect as per scope of works and technical specifications. |
| 273 | Electrically operated screw rod hoist of adequate capacity including all accessories i.e. central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 274 | Local Control Panel for hoist including all components, instruments, enclosures, cabling etc. complete in all respect as per scope of works and technical specifications. |
| 275 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 276 | Mandatory Spare parts in accordance with clause 11.9 of Particular Technical Specifications. |
| 277 | FISH LADDER SERVICE GATE WITH SCREW ROD HOIST |
| 278 | Slide type Fish ladder service gate for a clear opening of 0.5 m (W) x 0.7 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement etc. complete in all respect as per scope of works and technical specifications. |
| 279 | First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles etc. complete in all respect as per scope of works and technical specifications. |
| 280 | Second stage embedded parts such as sill beam, seal seats, guides, anchor bolts, nuts & washers etc. complete in all respect as per scope of works and technical specifications. |
| 281 | Electrically operated screw rod hoist of adequate capacity including all accessories i.e. central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 282 | Local Control Panel for hoist including all components, instruments, enclosures, cabling etc. complete in all respect as per scope of works and technical specifications. |
| 283 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 284 | Mandatory Spare parts in accordance with clause 12.9 of Particular Technical Specifications. |
| 285 | SILT FLUSHING GATE WITH HYDRAULIC HOIST |
| 286 | Bonneted vertical lift slide type Silt flushing gates for a clear opening of 0.75 m (W) x 1.80 m (H) complete in all respect as per scope of works and technical specifications. |
| 287 | First stage embedded parts (anchors), Air vent pipes etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structures etc. complete in all respect as per scope of works and technical specifications. |
| 288 | Second stage embedded parts and anchorages complete with sill beam, seal seats, guides, bonnet etc. complete in all respect as per scope of works and technical specifications. |
| 289 | Transitions and Conduit Liner Sections (Vent Steel liner) complete in all respect as per scope of works and technical specifications. |
| 290 | Double acting Hydraulic Hoists of adequate capacity including all the accessories such as upper and lower cylinder head, piston and stem, self lubricating bearing and other associated components etc. complete in all respect as per scope of works and technical specifications. |
| 291 | Hydraulic power pack assembly, including oil tank, seamless piping between power pack and cylinders and pipe fittings/supports and other accessories like flexible pressure hoses, pipe connectors, ball valves etc. complete in all respect as per scope of works and technical specifications. |
| 292 | Local electrical control panel for hoist (1 set for each hoist) including all components, instruments, enclosure, ducts, cabling between local control panel & hydraulic power pack, etc. complete in all respect as per scope of works and technical specifications. |
| 293 | EOT cranes of 10 T (minimum) capacity complete in all respect as per scope of works and technical specifications. Three numbers of U hooks, each of 5 T capacity complete in all respect to be embedded at the crown of each Silt flushing tunnel as per scope of works and technical specifications. |
| 294 | Seals & seal assemblies etc. complete in all respect as per scope of works and technical specifications. |
| 295 | Mandatory Spare parts in accordance with clause 13.9 of Particular Technical Specifications. |
| 296 | INSTRUMENTATION & CONTROL SYSTEM |
| 297 | PLC based remote control system complete with all accessories complete in all respect as per scope of works and technical specifications. |
| 298 | Power distribution board, Feeder Panels and Local Control Panels for all HM equipment with necessary auxiliaries complete in all respect as per scope of works and technical specifications. |
| 299 | Redundant AC-DC and / or DC-DC convertors along with 24V sub-distribution DC distribution boards etc. complete in all respect as per scope of works and technical specifications. |
| 300 | Power, Control, Instrumentation cables etc. along with all necessary accessories like lugs, cable trays etc complete in all respect as per scope of works and technical specifications. |
| 301 | Illumination of all gate decks and hoists etc. complete in all respect as per scope of works and technical specifications. |
| 302 | Earthing of all gates, hoists and electrical system etc. complete in all respect as per scope of works and technical specifications. |
| 303 | Instrumentation system complete in all respect as per scope of works and technical specifications. |
| 304 | Mandatory Spare parts in accordance with clause 14.8 of Particular Technical Specifications. |
| 305 | DG SETS |
| 306 | 500 kVA, 415V, 0.80 P.F. 50Hz, 3 phase, CPCB 4 Plus silent diesel generator complete in all respect as per scope of work and technical specifications. |
| 307 | Mandatory Spare parts in accordance with clause 15.6 of Particular Technical Specifications. |
| 308 | MANDATORY TOOL & TACKLES |
| 309 | Mandatory Tools & Tackles as per scope of works, GTS & PTS |
| 310 | RADIAL GATES WITH HYDRAULIC HOIST |
| 311 | Radial gate for a clear opening size of 18.5 m (W) x 14.3 m (H) complete with skin plate, horizontal girders, vertical stiffeners, inclined arms, bracings, trunnion assemblies, guide rollers, lifting brackets, anchors, trunnion brackets, dogging arrangement, access ladder with hand railing and safety cage, walkway platform between piers etc. complete in all respect as per scope of works and technical specifications. |
| 312 | Radial gate with flap gate for a clear opening size of 18.5 m (W) x 14.3 m (H) including flap gate of size 10.0 m (W) x 2.0 m (H) complete with skin plate, horizontal girders, vertical stiffeners, inclined arms, bracings, trunnion assemblies, guide rollers, seals & seal seat for flap gate, Rubber seals assemblies for flap gate, lifting brackets, anchors, trunnion brackets, dogging arrangement, access ladder with hand railing and safety cage, walkway platform between piers etc. complete in all respect as per scope of works and technical specifications. |
| 313 | First stage embedded parts (anchors) in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure etc. complete in all respect as per scope of works and technical specifications. |
| 314 | Second stage embedded parts complete with sill beam, wall plates, top seal seat with anchor bolts, nuts & washers and full-length anchors for trunnion brackets, anchors for steel support beam for hoist, etc. complete in all respect as per scope of works and technical specifications. |
| 315 | Single acting twin cylinders hydraulic hoist of adequate stroke/capacity including all the accessories such as cylinder support steel beam with bracket and connecting pin, self-lubricating bearing for either ends, gate position indicator and sensor/limit switches for operation of radial gates and other associated components required for the erection and commissioning etc. complete in all respect as per scope of works and technical specifications. |
| 316 | Independent hydraulic power pack assembly & control system including oil tank, hydraulic oil, seamless piping between power pack and cylinders and pipe fittings/ supports and other accessories like flexible pressure hoses, pipe connectors, ball valves, heavy duty pipe clamps, lighting and other fittings etc. complete in all respects for operation of hydraulic hoists as per scope of works and technical specifications. |
| 317 | Double acting twin cylinders hydraulic hoist of adequate stroke/capacity including all the accessories, hydraulic power pack & control system for smooth operation of flap gate including motor, pump, control panel, seamless piping, pressure gauges, flow control valves, pressure switches etc. with controls, manual controls, limit switches and other fittings etc. complete in all respect as per scope of works and technical specifications. |
| 318 | Local electrical control panel for each hoist including all components, instruments, enclosure, ducts, cabling between local control panel & hydraulic power pack, etc. complete in all respects for operation of Hydraulic Power Pack as per scope of works and technical specifications. |
| 319 | Rubber seals (bottom and sides etc.) assemblies complete in all respect as per scope of works and technical specifications. |
| 320 | Trolley mounted (mobile) gasoline engine complete with control and accessories complete in all respect as per scope of works and technical specifications. |
| 321 | Hydraulic oil filtering unit complete with all accessories, equipment, instruments etc.complete in all respect as per scope of works and technical specifications. |
| 322 | Low vacuum dehydration and degasification unit complete with control and accessories including One (01) unit of contamination checking kit complete in all respect as per scope of works and technical specifications. |
| 323 | Mandatory Spare parts in accordance with clause 1.9 of Particular Technical Specifications. |
| 324 | STOPLOG GATE WITH GANTRY CRANE AND LIFTING BEAM |
| 325 | Stop log units of vertical lift fixed wheel type for a clear opening size of 18.5 m (W) x 14.3 m (H) complete with skin plate, stiffeners, horizontal girders, end vertical girders, sliding pads, guide rollers, lifting & latching arrangement, filling valves in top unit, etc. complete in all respect as per scope of works and technical specifications. |
| 326 | First stage embedded parts (anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate for gate groove and first stage embedded parts (anchors) for storage pit as per requirement complete in all respect as per scope of works and technical specifications. |
| 327 | Second stage embedded parts such as sill beam, slide tracks & side seal seats, side guides, top seal seat, anchor bolts, nuts & washers, support angles, latching and storage arrangement over the piers. Embedded parts and ladder for storage pit with steel grating for stoplog units etc. complete in all respect as per scope of works and technical specifications. |
| 328 | Lifting beam of adequate capacity with automatic engaging / disengaging device complete with frame, guides, pulleys, bearings, counterweight and other accessories, etc. complete in all respect as per scope of works and technical specifications. |
| 329 | Electrically operated travelling gantry crane with cross-travel arrangement of adequate capacity, cabin operated along with necessary structural, mechanical and electrical control equipment including gantry track rails extended up to parking, embedded parts, end stoppers, counterweight and other accessories for safe operation of spillway stoplogs units complete in all respect as per scope of works and technical specifications. |
| 330 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 331 | Mandatory Spare parts in accordance with the clause 2.9 of Particular Technical Specifications. |
| 332 | INTAKE BULKHEAD GATE WITH ROPE DRUM HOIST |
| 333 | Vertical lift fixed wheel type Intake Bulkhead Gate for a clear opening size of 3.82 m (W) x 6.0 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels, filling valve etc. complete in all respect as per scope of works and technical specifications. |
| 334 | First stage embedded parts (anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 335 | Second stage embedded parts complete with sill beam, seal seats, Side Guides, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 336 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 337 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 338 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 339 | Mandatory Spare parts in accordance with clause 3.9 of Particular Technical Specifications. |
| 340 | INTAKE SERVICE GATE WITH ROPE DRUM HOIST |
| 341 | Vertical lift fixed wheel type Intake Service Gate for a clear opening size of 3.82 m (W) x 6.0 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels etc. complete in all respect as per scope of works and technical specifications. |
| 342 | First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 343 | Second stage embedded parts complete with sill beam, seal seats, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 344 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 345 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 346 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 347 | Mandatory Spare parts in accordance with clause 4.9 of Particular Technical Specifications. |
| 348 | INTAKE HRT GATE WITH ROPE DRUM HOIST |
| 349 | Vertical lift fixed wheel type Intake HRT Gate for a clear opening size of 3.82 m (W) x 4.60 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels, filling valve etc. complete in all respect as per scope of works and technical specifications. |
| 350 | First stage embedded parts (anchors), etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 351 | Second stage embedded parts complete with sill beam, seal seats, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 352 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 353 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 354 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 355 | Mandatory Spare parts in accordance with clause 5.9 of Particular Technical Specifications. |
| 356 | INTAKE TRASH RACK AND TRCM |
| 357 | Trash racks suitable for each opening of intake structure 7.2 m (W) x 11.68 m (H) (inclined height) size complete in all respect as per scope of works and technical specifications. |
| 358 | First stage inserts and embedded parts, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts, pipes for sensors etc. complete in all respect as per scope of works and technical specifications. |
| 359 | Second stage embedded parts complete with guides, bottom base, etc complete in all respect. as per scope of works and technical specifications. |
| 360 | Automatically engaging / disengaging type lifting beam with two positively engaging & disengaging type hooks by means of counter weight & lever mechanism etc. for handling of trash rack panels complete in all respect.as per scope of works and technical specifications. |
| 361 | Hydraulically operated Semi-automatic trash rack cleaning machine complete in all respect along with bucket, control devices, rails and fixtures, grapple hoist, cable reeling drum along with tool kits etc. complete in all respect as per scope of works and technical specifications. |
| 362 | Mandatory Spare parts in accordance with clause 6.9 of Particular Technical Specifications. |
| 363 | ADIT PLUG GATE |
| 364 | HRT Adit plug Hinge type gate for a clear opening of 2.5 m (W) x 2.5 m (H) with skin plate, horizontal girders, vertical stiffeners and end verticals and locking, wire rope pulling machine to operate the hinge gate etc. complete in all respect as per scope of works and technical specifications. |
| 365 | First and second stage embedded parts such as bottom and top seal seats, side seal seat cum bearing plate, anchor bolts, nuts & washers, erection hooks etc. for hinged gate complete in all respect. as per scope of works and technical specifications. |
| 366 | Rubber seals assemblies complete in all respect as per scope of works and technical specifications. |
| 367 | Mandatory Spare parts in accordance with clause 7.9 of Particular Technical Specifications. |
| 368 | SURGE SHAFT GATES WITH ROPE DRUM HOIST |
| 369 | Vertical lift fixed wheel type Surge shaft gates for a clear opening of 2.6 m (W) x 3.3 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement and filling valves etc. complete in all respect as per scope of works and technical specifications. |
| 370 | First stage embedded parts (anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles complete in all respect as per scope of works and technical specifications. |
| 371 | Second stage embedded parts such as sill beam, seal seats, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 372 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 373 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 374 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 375 | Mandatory Spare parts in accordance with clause 8.9 of Particular Technical Specifications. |
| 376 | DRAFT TUBE GATES WITH ROPE DRUM HOIST |
| 377 | Vertical lift fixed wheel type Draft tube gates for a clear opening of 3.6 m (W) x 1.9 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement and filling valves etc. complete in all respect as per scope of works and technical specifications. |
| 378 | First stage embedded parts(anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles complete in all respect as per scope of works and technical specifications. |
| 379 | Second stage embedded parts such as sill beam, roller tracks and side seal seats, guides, seal seat, anchor bolts, nuts & washers etc complete in all respect as per scope of works and technical specifications. |
| 380 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 381 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect. |
| 382 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 383 | Mandatory Spare parts in accordance with clause 9.9 of Particular Technical Specifications. |
| 384 | TAIL RACE TUNNEL GATE WITH ROPE DRUM HOIST |
| 385 | Vertical lift fixed wheel type Tail Race Tunnel Gate for a clear opening size of 6.0 m (W) x 4.0 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels, filling valve etc. complete in all respect as per scope of works and technical specifications. |
| 386 | First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 387 | Second stage embedded parts complete with sill beam, seal seats, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 388 | Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 389 | Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 390 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 391 | Mandatory Spare parts in accordance with clause 10.9 of Particular Technical Specifications. |
| 392 | FISH LADDER EMERGENCY GATE WITH SCREW ROD HOIST |
| 393 | Slide type Fish ladder emergency gate for a clear opening of 0.5 m (W) x 0.7 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement etc. complete in all respect as per scope of works and technical specifications. |
| 394 | First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles etc. complete in all respect as per scope of works and technical specifications. |
| 395 | Second stage embedded parts such as sill beam, seal seats, guides, anchor bolts, nuts & washers etc. complete in all respect as per scope of works and technical specifications. |
| 396 | Electrically operated screw rod hoist of adequate capacity including all accessories i.e. central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 397 | Local Control Panel for hoist including all components, instruments, enclosures, cabling etc. complete in all respect as per scope of works and technical specifications. |
| 398 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 399 | Mandatory Spare parts in accordance with clause 11.9 of Particular Technical Specifications. |
| 400 | FISH LADDER SERVICE GATE WITH SCREW ROD HOIST |
| 401 | Slide type Fish ladder service gate for a clear opening of 0.5 m (W) x 0.7 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement etc. complete in all respect as per scope of works and technical specifications. |
| 402 | First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles etc. complete in all respect as per scope of works and technical specifications. |
| 403 | Second stage embedded parts such as sill beam, seal seats, guides, anchor bolts, nuts & washers etc. complete in all respect as per scope of works and technical specifications. |
| 404 | Electrically operated screw rod hoist of adequate capacity including all accessories i.e. central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 405 | Local Control Panel for hoist including all components, instruments, enclosures, cabling etc. complete in all respect as per scope of works and technical specifications. |
| 406 | Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 407 | Mandatory Spare parts in accordance with clause 12.9 of Particular Technical Specifications. |
| 408 | SILT FLUSHING GATE WITH HYDRAULIC HOIST |
| 409 | Bonneted vertical lift slide type Silt flushing gates for a clear opening of 0.75 m (W) x 1.80 m (H) complete in all respect as per scope of works and technical specifications. |
| 410 | First stage embedded parts (anchors), Air vent pipes etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structures etc. complete in all respect as per scope of works and technical specifications. |
| 411 | Second stage embedded parts and anchorages complete with sill beam, seal seats, guides, bonnet etc. complete in all respect as per scope of works and technical specifications. |
| 412 | Transitions and Conduit Liner Sections (Vent Steel liner) complete in all respect as per scope of works and technical specifications. |
| 413 | Double acting Hydraulic Hoists of adequate capacity including all the accessories such as upper and lower cylinder head, piston and stem, self lubricating bearing and other associated components etc. complete in all respect as per scope of works and technical specifications. |
| 414 | Hydraulic power pack assembly, including oil tank, seamless piping between power pack and cylinders and pipe fittings/supports and other accessories like flexible pressure hoses, pipe connectors, ball valves etc. complete in all respect as per scope of works and technical specifications. |
| 415 | Local electrical control panel for hoist (1 set for each hoist) including all components, instruments, enclosure, ducts, cabling between local control panel & hydraulic power pack, etc. complete in all respect as per scope of works and technical specifications. |
| 416 | EOT cranes of 10 T (minimum) capacity complete in all respect as per scope of works and technical specifications. Three numbers of U hooks, each of 5 T capacity complete in all respect to be embedded at the crown of each Silt flushing tunnel as per scope of works and technical specifications. |
| 417 | Seals & seal assemblies etc. complete in all respect as per scope of works and technical specifications. |
| 418 | Mandatory Spare parts in accordance with clause 13.9 of Particular Technical Specifications. |
| 419 | INSTRUMENTATION & CONTROL SYSTEM |
| 420 | PLC based remote control system complete with all accessories complete in all respect as per scope of works and technical specifications. |
| 421 | Power distribution board, Feeder Panels and Local Control Panels for all HM equipment with necessary auxiliaries complete in all respect as per scope of works and technical specifications. |
| 422 | Redundant AC-DC and / or DC-DC convertors along with 24V sub-distribution DC distribution boards etc. complete in all respect as per scope of works and technical specifications. |
| 423 | Power, Control, Instrumentation cables etc. along with all necessary accessories like lugs, cable trays etc complete in all respect as per scope of works and technical specifications. |
| 424 | Illumination of all gate decks and hoists etc. complete in all respect as per scope of works and technical specifications. |
| 425 | Earthing of all gates, hoists and electrical system etc. complete in all respect as per scope of works and technical specifications. |
| 426 | Instrumentation system complete in all respect as per scope of works and technical specifications. |
| 427 | Mandatory Spare parts in accordance with clause 14.8 of Particular Technical Specifications. |
| 428 | DG SETS |
| 429 | 500 kVA, 415V, 0.80 P.F. 50Hz, 3 phase, CPCB 4 Plus silent diesel generator complete in all respect as per scope of work and technical specifications. |
| 430 | Mandatory Spare parts in accordance with clause 15.6 of Particular Technical Specifications. |
| 431 | MANDATORY TOOL & TACKLES |
| 432 | Mandatory Tools & Tackles as per scope of works, GTS & PTS |
| 433 | RADIAL GATES WITH HYDRAULIC HOIST |
| 434 | Erection, Testing & Commissioning of Radial gate for a clear opening size of 18.5 m (W) x 14.3 m (H) complete with skin plate, horizontal girders, vertical stiffeners, inclined arms, bracings, trunnion assemblies, guide rollers, lifting brackets, anchors, trunnion brackets, dogging arrangement, access ladder with hand railing and safety cage, walkway platform between piers etc. complete in all respect as per scope of works and technical specifications. |
| 435 | Erection, Testing & Commissioning of Radial gate with flap gate for a clear opening size of 18.5 m (W) x 14.3 m (H) including flap gate of size 10.0 m (W) x 2.0 m (H) complete with skin plate, horizontal girders, vertical stiffeners, inclined arms, bracings, trunnion assemblies, guide rollers, seals & seal seat for flap gate, Rubber seals assemblies for flap gate, lifting brackets, anchors, trunnion brackets, dogging arrangement, access ladder with hand railing and safety cage, walkway platform between piers etc. complete in all respect as per scope of works and technical specifications. |
| 436 | Erection, Testing & Commissioning of First stage embedded parts (anchors) in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure etc. complete in all respect as per scope of works and technical specifications. |
| 437 | Erection, Testing & Commissioning of Second stage embedded parts complete with sill beam, wall plates, top seal seat with anchor bolts, nuts & washers and full-length anchors for trunnion brackets, anchors for steel support beam for hoist, etc. complete in all respect as per scope of works and technical specifications. |
| 438 | Erection, Testing & Commissioning of Single acting twin cylinders hydraulic hoist of adequate stroke/capacity including all the accessories such as cylinder support steel beam with bracket and connecting pin, self-lubricating bearing for either ends, gate position indicator and sensor/limit switches for operation of radial gates and other associated components required for the erection and commissioning etc. complete in all respect as per scope of works and technical specifications. |
| 439 | Erection, Testing & Commissioning of Independent hydraulic power pack assembly & control system including oil tank, hydraulic oil, seamless piping between power pack and cylinders and pipe fittings/ supports and other accessories like flexible pressure hoses, pipe connectors, ball valves, heavy duty pipe clamps, lighting and other fittings etc. complete in all respects for operation of hydraulic hoists as per scope of works and technical specifications. |
| 440 | Erection, Testing & Commissioning of Double acting twin cylinders hydraulic hoist of adequate stroke/capacity including all the accessories, hydraulic power pack & control system for smooth operation of flap gate including motor, pump, control panel, seamless piping, pressure gauges, flow control valves, pressure switches etc. with controls, manual controls, limit switches and other fittings etc. complete in all respect as per scope of works and technical specifications. |
| 441 | Erection, Testing & Commissioning of Local electrical control panel for each hoist including all components, instruments, enclosure, ducts, cabling between local control panel & hydraulic power pack, etc. complete in all respects for operation of Hydraulic Power Pack as per scope of works and technical specifications. |
| 442 | Erection, Testing & Commissioning of Rubber seals (bottom and sides etc.) assemblies complete in all respect as per scope of works and technical specifications. |
| 443 | Testing & Commissioning of Trolley mounted (mobile) gasoline engine complete with control and accessories complete in all respect as per scope of works and technical specifications. |
| 444 | Testing & Commissioning of Hydraulic oil filtering unit complete with all accessories, equipment, instruments etc.complete in all respect as per scope of works and technical specifications. |
| 445 | Testing & Commissioning of Low vacuum dehydration and degasification unit complete with control and accessories including One (01) unit of contamination checking kit complete in all respect as per scope of works and technical specifications. |
| 446 | STOPLOG GATE WITH GANTRY CRANE AND LIFTING BEAM |
| 447 | Erection, Testing & Commissioning of Stop log units of vertical lift fixed wheel type for a clear opening size of 18.5 m (W) x 14.3 m (H) complete with skin plate, stiffeners, horizontal girders, end vertical girders, sliding pads, guide rollers, lifting & latching arrangement, filling valves in top unit, etc. complete in all respect as per scope of works and technical specifications. |
| 448 | Erection, Testing & Commissioning of First stage embedded parts (anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate for gate groove and first stage embedded parts (anchors) for storage pit as per requirement complete in all respect as per scope of works and technical specifications. |
| 449 | Erection, Testing & Commissioning of Second stage embedded parts such as sill beam, slide tracks & side seal seats, side guides, top seal seat, anchor bolts, nuts & washers, support angles, latching and storage arrangement over the piers. Embedded parts and ladder for storage pit with steel grating for stoplog units etc. complete in all respect as per scope of works and technical specifications. |
| 450 | Erection, Testing & Commissioning of Lifting beam of adequate capacity with automatic engaging / disengaging device complete with frame, guides, pulleys, bearings, counterweight and other accessories, etc. complete in all respect as per scope of works and technical specifications. |
| 451 | Erection, Testing & Commissioning of Electrically operated travelling gantry crane with cross-travel arrangement of adequate capacity, cabin operated along with necessary structural, mechanical and electrical control equipment including gantry track rails extended up to parking, embedded parts, end stoppers, counterweight and other accessories for safe operation of spillway stoplogs units complete in all respect as per scope of works and technical specifications. |
| 452 | Erection, Testing & Commissioning of Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 453 | INTAKE BULKHEAD GATE WITH ROPE DRUM HOIST |
| 454 | Erection, Testing & Commissioning of Vertical lift fixed wheel type Intake Bulkhead Gate for a clear opening size of 3.82 m (W) x 6.0 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels, filling valve etc. complete in all respect as per scope of works and technical specifications. |
| 455 | Erection, Testing & Commissioning of First stage embedded parts (anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 456 | Erection, Testing & Commissioning of Second stage embedded parts complete with sill beam, seal seats, Side Guides, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 457 | Erection, Testing & Commissioning of Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 458 | Erection, Testing & Commissioning of Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 459 | Erection, Testing & Commissioning of Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 460 | INTAKE SERVICE GATE WITH ROPE DRUM HOIST |
| 461 | Erection, Testing & Commissioning of Vertical lift fixed wheel type Intake Service Gate for a clear opening size of 3.82 m (W) x 6.0 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels etc. complete in all respect as per scope of works and technical specifications. |
| 462 | Erection, Testing & Commissioning of First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 463 | Erection, Testing & Commissioning of Second stage embedded parts complete with sill beam, seal seats, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 464 | Erection, Testing & Commissioning of Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 465 | Erection, Testing & Commissioning of Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 466 | Erection, Testing & Commissioning of Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 467 | INTAKE HRT GATE WITH ROPE DRUM HOIST |
| 468 | Erection, Testing & Commissioning of Vertical lift fixed wheel type Intake HRT Gate for a clear opening size of 3.82 m (W) x 4.60 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels, filling valve etc. complete in all respect as per scope of works and technical specifications. |
| 469 | Erection, Testing & Commissioning of First stage embedded parts (anchors), etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 470 | Erection, Testing & Commissioning of Second stage embedded parts complete with sill beam, seal seats, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 471 | Erection, Testing & Commissioning of Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 472 | Erection, Testing & Commissioning of Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 473 | Erection, Testing & Commissioning of Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 474 | INTAKE TRASH RACK AND TRCM |
| 475 | Erection, Testing & Commissioning of Trash racks suitable for each opening of intake structure 7.2 m (W) x 11.68 m (H) (inclined height) size complete in all respect as per scope of works and technical specifications. |
| 476 | Erection, Testing & Commissioning of First stage inserts and embedded parts, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts, pipes for sensors etc. complete in all respect as per scope of works and technical specifications. |
| 477 | Erection, Testing & Commissioning of Second stage embedded parts complete with guides, bottom base, etc complete in all respect. as per scope of works and technical specifications. |
| 478 | Erection, Testing & Commissioning of Automatically engaging / disengaging type lifting beam with two positively engaging & disengaging type hooks by means of counter weight & lever mechanism etc. for handling of trash rack panels complete in all respect.as per scope of works and technical specifications. |
| 479 | Erection, Testing & Commissioning of Hydraulically operated Semi-automatic trash rack cleaning machine complete in all respect along with bucket, control devices, rails and fixtures, grapple hoist, cable reeling drum along with tool kits etc. complete in all respect as per scope of works and technical specifications. |
| 480 | ADIT PLUG GATE |
| 481 | Erection, Testing & Commissioning of HRT Adit plug Hinge type gate for a clear opening of 2.5 m (W) x 2.5 m (H) with skin plate, horizontal girders, vertical stiffeners and end verticals and locking, wire rope pulling machine to operate the hinge gate etc. complete in all respect as per scope of works and technical specifications. |
| 482 | Erection, Testing & Commissioning of First and second stage embedded parts such as bottom and top seal seats, side seal seat cum bearing plate, anchor bolts, nuts & washers, erection hooks etc. for hinged gate complete in all respect. as per scope of works and technical specifications. |
| 483 | Erection, Testing & Commissioning of Rubber seals assemblies complete in all respect as per scope of works and technical specifications. |
| 484 | SURGE SHAFT GATES WITH ROPE DRUM HOIST |
| 485 | Erection, Testing & Commissioning of Vertical lift fixed wheel type Surge shaft gates for a clear opening of 2.6 m (W) x 3.3 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement and filling valves etc. complete in all respect as per scope of works and technical specifications. |
| 486 | Erection, Testing & Commissioning of First stage embedded parts (anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles complete in all respect as per scope of works and technical specifications. |
| 487 | Erection, Testing & Commissioning of Second stage embedded parts such as sill beam, seal seats, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 488 | Erection, Testing & Commissioning of Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 489 | Erection, Testing & Commissioning of Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 490 | Erection, Testing & Commissioning of Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 491 | DRAFT TUBE GATES WITH ROPE DRUM HOIST |
| 492 | Erection, Testing & Commissioning of Vertical lift fixed wheel type Draft tube gates for a clear opening of 3.6 m (W) x 1.9 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement and filling valves etc. complete in all respect as per scope of works and technical specifications. |
| 493 | Erection, Testing & Commissioning of First stage embedded parts(anchors), 500 mm dia air vent pipe, pipes for sensors etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles complete in all respect as per scope of works and technical specifications. |
| 494 | Erection, Testing & Commissioning of Second stage embedded parts such as sill beam, roller tracks and side seal seats, guides, seal seat, anchor bolts, nuts & washers etc complete in all respect as per scope of works and technical specifications. |
| 495 | Erection, Testing & Commissioning of Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 496 | Erection, Testing & Commissioning of Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect. |
| 497 | Erection, Testing & Commissioning of Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 498 | TAIL RACE TUNNEL GATE WITH ROPE DRUM HOIST |
| 499 | Erection, Testing & Commissioning of Vertical lift fixed wheel type Tail Race Tunnel Gate for a clear opening size of 6.0 m (W) x 4.0 m (H) complete with skin plate, vertical girders, stiffeners, horizontal girders, wheels, filling valve etc. complete in all respect as per scope of works and technical specifications. |
| 500 | Erection, Testing & Commissioning of First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structure complete in all respect as per scope of works and technical specifications. |
| 501 | Erection, Testing & Commissioning of Second stage embedded parts complete with sill beam, seal seats, wheel tracks, guides, etc. complete in all respect as per scope of works and technical specifications. |
| 502 | Erection, Testing & Commissioning of Electrically operated rope drum hoist of adequate capacity with central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, and local control panel, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 503 | Erection, Testing & Commissioning of Local Control Panel for hoist including all components, instruments, enclosures, etc. complete in all respect as per scope of works and technical specifications. |
| 504 | Erection, Testing & Commissioning of Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 505 | FISH LADDER EMERGENCY GATE WITH SCREW ROD HOIST |
| 506 | Erection, Testing & Commissioning of Slide type Fish ladder emergency gate for a clear opening of 0.5 m (W) x 0.7 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement etc. complete in all respect as per scope of works and technical specifications. |
| 507 | Erection, Testing & Commissioning of First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles etc. complete in all respect as per scope of works and technical specifications. |
| 508 | Erection, Testing & Commissioning of Second stage embedded parts such as sill beam, seal seats, guides, anchor bolts, nuts & washers etc. complete in all respect as per scope of works and technical specifications. |
| 509 | Erection, Testing & Commissioning of Electrically operated screw rod hoist of adequate capacity including all accessories i.e. central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 510 | Erection, Testing & Commissioning of Local Control Panel for hoist including all components, instruments, enclosures, cabling etc. complete in all respect as per scope of works and technical specifications. |
| 511 | Erection, Testing & Commissioning of Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 512 | FISH LADDER SERVICE GATE WITH SCREW ROD HOIST |
| 513 | Erection, Testing & Commissioning of Slide type Fish ladder service gate for a clear opening of 0.5 m (W) x 0.7 m (H) with skin plate, stiffeners, horizontal girders, end vertical girders, wheel assemblies, guide shoes, lifting arrangements, dogging/latching arrangement etc. complete in all respect as per scope of works and technical specifications. |
| 514 | Erection, Testing & Commissioning of First stage embedded parts (anchors) etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist trestles etc. complete in all respect as per scope of works and technical specifications. |
| 515 | Erection, Testing & Commissioning of Second stage embedded parts such as sill beam, seal seats, guides, anchor bolts, nuts & washers etc. complete in all respect as per scope of works and technical specifications. |
| 516 | Erection, Testing & Commissioning of Electrically operated screw rod hoist of adequate capacity including all accessories i.e. central drive unit, end gear boxes, wires, pulley sheaves, including manual operating gear box assembly with removable cover, gate position indicator with limit switches, cabling, hoist supporting structure along with trestles, platform, anchorage, ladder, hand railing, etc. complete in all respect as per scope of works and technical specifications. |
| 517 | Erection, Testing & Commissioning of Local Control Panel for hoist including all components, instruments, enclosures, cabling etc. complete in all respect as per scope of works and technical specifications. |
| 518 | Erection, Testing & Commissioning of Rubber seal (bottom, sides, top and corners) assemblies complete in all respect as per scope of works and technical specifications. |
| 519 | SILT FLUSHING GATE WITH HYDRAULIC HOIST |
| 520 | Erection, Testing & Commissioning of Bonneted vertical lift slide type Silt flushing gates for a clear opening of 0.75 m (W) x 1.80 m (H) complete in all respect as per scope of works and technical specifications. |
| 521 | Erection, Testing & Commissioning of First stage embedded parts (anchors), Air vent pipes etc. in the primary concrete to facilitate erection of second stage embedded parts of gate and hoist supporting structures etc. complete in all respect as per scope of works and technical specifications. |
| 522 | Erection, Testing & Commissioning of Second stage embedded parts and anchorages complete with sill beam, seal seats, guides, bonnet etc. complete in all respect as per scope of works and technical specifications. |
| 523 | Erection, Testing & Commissioning of Transitions and Conduit Liner Sections (Vent Steel liner) complete in all respect as per scope of works and technical specifications. |
| 524 | Erection, Testing & Commissioning of Double acting Hydraulic Hoists of adequate capacity including all the accessories such as upper and lower cylinder head, piston and stem, self lubricating bearing and other associated components etc. complete in all respect as per scope of works and technical specifications. |
| 525 | Erection, Testing & Commissioning of Hydraulic power pack assembly, including oil tank, seamless piping between power pack and cylinders and pipe fittings/supports and other accessories like flexible pressure hoses, pipe connectors, ball valves etc. complete in all respect as per scope of works and technical specifications. |
| 526 | Erection, Testing & Commissioning of Local electrical control panel for hoist (1 set for each hoist) including all components, instruments, enclosure, ducts, cabling between local control panel & hydraulic power pack, etc. complete in all respect as per scope of works and technical specifications. |
| 527 | Erection, Testing & Commissioning of EOT cranes of 10 T (minimum) capacity and Three numbers (03) of U hooks, each of 5 T capacity at the crown of each Silt flushing tunnel complete in all respect as per scope of works and technical specifications. |
| 528 | Erection, Testing & Commissioning of Seals & seal assemblies etc. complete in all respect as per scope of works and technical specifications. |
| 529 | INSTRUMENTATION & CONTROL SYSTEM |
| 530 | Erection, Testing & Commissioning of PLC based remote control system complete with all accessories complete in all respect as per scope of works and technical specifications. |
| 531 | Erection, Testing & Commissioning of Power distribution board, Feeder Panels and Local Control Panels for all HM equipment with necessary auxiliaries complete in all respect as per scope of works and technical specifications. |
| 532 | Erection, Testing & Commissioning of Redundant AC-DC and / or DC-DC convertors along with 24V sub-distribution DC distribution boards etc. complete in all respect as per scope of works and technical specifications. |
| 533 | Erection, Testing & Commissioning of Power, Control, Instrumentation cables etc. along with all necessary accessories like lugs, cable trays etc complete in all respect as per scope of works and technical specifications. |
| 534 | Erection, Testing & Commissioning of Illumination of all gate decks and hoists etc. complete in all respect as per scope of works and technical specifications. |
| 535 | Erection, Testing & Commissioning of Earthing of all gates, hoists and electrical system etc. complete in all respect as per scope of works and technical specifications. |
| 536 | Erection, Testing & Commissioning of Instrumentation system complete in all respect as per scope of works and technical specifications. |
| 537 | DG SETS |
| 538 | Erection, Testing & Commissioning of 500 kVA, 415V, 0.80 P.F. 50Hz, 3 phase, CPCB 4 Plus silent diesel generator complete in all respect as per scope of work and technical specifications. |
| 539 | Recommended spare parts item - 1 |
| 540 | Recommended spare parts item - 2 |
| 541 | Recommended spare parts item - 3 |
| 542 | Recommended spare parts item - 4 |
| 543 | Recommended spare parts item - 5 |
| 544 | Recommended spare parts item - 6 |
| 545 | Recommended spare parts item - 7 |
| 546 | Recommended spare parts item - 8 |
| 547 | Recommended spare parts item - 9 |
| 548 | Recommended spare parts item - 10 |
| 549 | Recommended spare parts item - 11 |
| 550 | Recommended spare parts item - 12 |
| 551 | Recommended spare parts item - 13 |
| 552 | Recommended spare parts item - 14 |
| 553 | Recommended spare parts item - 15 |
| 554 | Recommended spare parts item - 16 |
| 555 | Recommended spare parts item - 17 |
| 556 | Recommended spare parts item - 18 |
| 557 | Recommended spare parts item - 19 |
| 558 | Recommended spare parts item - 20 |
| 559 | Recommended spare parts item - 21 |
| 560 | Recommended spare parts item - 22 |
| 561 | Recommended spare parts item - 23 |
| 562 | Recommended spare parts item - 24 |
| 563 | Recommended spare parts item - 25 |
| 564 | Recommended spare parts item - 26 |
| 565 | Recommended spare parts item - 27 |
| 566 | Recommended spare parts item - 28 |
| 567 | Recommended spare parts item - 29 |
| 568 | Recommended spare parts item - 30 |
| 569 | Recommended spare parts item - 31 |
| 570 | Recommended spare parts item - 32 |
| 571 | Recommended spare parts item - 33 |
| 572 | Recommended spare parts item - 34 |
| 573 | Recommended spare parts item - 35 |
| 574 | Recommended spare parts item - 36 |
| 575 | Recommended spare parts item - 37 |
| 576 | Recommended spare parts item - 38 |
| 577 | Recommended spare parts item - 39 |
| 578 | Recommended spare parts item - 40 |
| 579 | Recommended spare parts item - 41 |
| 580 | Recommended spare parts item - 42 |
| 581 | Recommended spare parts item - 43 |
| 582 | Recommended spare parts item - 44 |
| 583 | Recommended spare parts item - 45 |
| 584 | Recommended spare parts item - 46 |
| 585 | Recommended spare parts item - 47 |
| 586 | Recommended spare parts item - 48 |
| 587 | Recommended spare parts item - 49 |
| 588 | Recommended spare parts item - 50 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysDec 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender