Tender For Painting, Installation Of Interlocking Tiles, Smart Classrooms, Kitchen Repairs, And Toilet Facilities At Upper Primary School, Bonsa.
Tender Value
25.17 Lakhs
Estimated cost
Bid Submission
10 Nov 2026
4 days left
EMD
51000
Bank guarantee accepted
Document Fee
854
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Saharanpur → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Painting, Installation Of Interlocking Tiles, Smart Classrooms, Kitchen Repairs, And Toilet Facilities At Upper Primary School, Bonsa.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as irected by Engineer-incharge. All kinds of soil DSR 2.6.1 |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR 4.1.8 |
| 3 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) DSR 6.1.2 |
| 4 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size de rived from natural sources) DSR 5.1.3 |
| 5 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in uperstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) As DSR 6.4.2 |
| 6 | Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete. DSR 2.27 |
| 7 | 12 mm cement plaster of mix :DSR 13.4.1 |
| 8 | 15 mm cement plaster:1:6 (1 cement : 6 fine sand) DSR 13.2.2 |
| 9 | 12 mm cement plaster of mix :DSR 13.4.1 |
| 10 | Cement concrete pavement with 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.D.S.R.No-11.7 |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). DSR 5.3 |
| 12 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Mild steel and Medium Tensile steel bars As DSR 5.22.1 |
| 13 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)DSR-10.15.1 |
| 14 | Filling of brick ballast in soak pit. i/c all etc. comp item no-0362 |
| 15 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.100 mm nominal dia Pipes DSR 18.9.9 |
| 16 | Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded sqm stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate D.S.R.-11.3.1 |
| 17 | Providing and fixing glass strips in joints of terrazo / cement concrete floors 40 mm wide and 4 mm thick D.S.R.-11.13.1 |
| 18 | Providing and laying vitrified floor tiles In different sizes (thickness to be specified by the manufacturer) with water absorption lass than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand),jointing with gray cement slurry@ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.11 .41.2 Size of Tile 600x600 mm |
| 19 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and confonning to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bad of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc.11.46.2 |
| 20 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the urface even and smooth complete. DSR 13.80 |
| 21 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre. DSR 13.41.1 |
| 22 | Finishing walls with 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004,Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.13.48A.1 New work (Two or more coats applied @ 1.43 litre/ 10sqm. Over and including priming coat of exterior primerapplied @ 0.90 litre/10 sqm DSR 13.48A.1 |
| 23 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture DSR 13.48.3 |
| 24 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C.flushing cistern, including flush pipe, with manuall controlled device (handle lever), conforming to IS : 7231, wilh all fittings and fixtures complete, including cutting and making good the walls and floors wherever W.C. pan with ISi marked black solid plastic seat and lid D.S.R.No-17.2.1 |
| 25 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting_ of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps mm with integral type foot rests D.S.R.No-17.7.1 |
| 26 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden deals with C.P. brass screws and washers complete.D.S.R.No-17.31 |
| 27 | Providing and fixing toilet paper holder C.P. brass D.S.R.No-17.34.1 |
| 28 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.D.S.R.No-18.48 |
| 29 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc.,complete. as per DSR 17.33. |
| 30 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved uality and colour, weighing not less than 105 gms. as per DSR 17.71. |
| 31 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes. having thennal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of Joints complete as per direction of Engineer in Charge.15 mm nominal dia Pipes 18.7.1 15mm dia |
| 32 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes. having thennal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of Joints complete as per direction of Engineer in Charge.25 mm nominal dia Pipes 18.7.3 25mm dia |
| 33 | Providing and fixing brass stop cock of approved quality 15mm nominal bore. D S R NO- 18.16.1 |
| 34 | Providing and rlXing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore D.S.R.No-18.49 |
| 35 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. dsr 1.10.1 |
| 36 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ 1 recessed medium class PVC conduit as required. 2 x 10sq. mm + 1 X 6 sq. mm earth wire 1.14,5 |
| 37 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.DSR 10.28 |
| 38 | Dismantling old plasteror skirting raking out joint and claening the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead. DSR 15.56 |
| 39 | 12 mm cement plaster of mix :DSR 13.4.1 |
| 40 | Dismantling precast concrete or stone slabs in walls, partition walls etc. including stacking within 50 metres lead 15.40.1 Thickness up to 40 mm D.S.R.No-15.40.1 |
| 41 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and nufacture, including applying additional coats wherever required, to achieve even shade and colour. DSR 13.82 |
| 42 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2x2.5 sq. mm + 1 X 2.5 sq. mm earth wire Wiring for circuit/ submain wiring alongwith earth 1.14.2 |
| 43 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ 1 recessed medium class PVC conduit as required. 2 x 4 sq. mm + 1 X 4 sq. mm earth wire 1.14,3 |
| 44 | Supply and fixing of LED Tube Light batten fitting 9 suitable for up to 1 X 22 watt LED tube light on surface complete in all respect. - UPPWD1413(A) CAT-AAA |
| 45 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase 9.2.3 |
| 46 | Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A each modular socket outlet and 5/6 A modular switch, connections etc. as required .1.31 |
| 47 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 each & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. D.S.R.No-1.32 |
| 48 | nstallation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm D.S.R.No-1.50.1 |
| 49 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole 2.10.1 |
| 50 | .Supply and fixing of CO2 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. UPPWD 1132 |
| 51 | Supply and fixing of a sign board including necessary supply of all materials, labour, Tools & plants etc. required for proper completion of the workAs Per S.E. (R.E.D.), Saharanpur Sanction |
| 52 | Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 As Per Mord S.R..- 3.4 |
| 53 | Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 As Per Mord S.R..- 11.04(I) P C C M 10 Nominal mix 1:3:6 |
| 54 | Brick masonry work in cement mortar in substructure complete excepting pointing and plastering, as per drawing and technical specification Clauses 602, 603, 604, 1202 & 1204 As Per Mord S.R..- 12.1 (ii) |
| 55 | Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 As Per Mord S.R..- 11.04(III) P C C M 10 Nominal mix 1:2:4 |
| 56 | Plastering with cement mortar (1:4), 12 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204 As Per Mord S.R..- 12.3 |
| 57 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. As Per Mord S.R.- 4.1) |
| 58 | Providing and Laying of Interlocking Concrete Block Pavements having thickness 80 mm as per drawings and Technical Specification Clause 1504 ISI marked confirming to IS: 15658-2006 I shaped mechanically compressed interloking cement concerete paver blocks, smooth high gloss finish, skid resistant; manufactured from rubber moulds through vibrocompression mechanism. high pressure and control vibration machine having plan dimension 200 x (160+120mm) with minimum 5mm thick topping of O.P. cement mixed with 25% marble powder. The Compressive strength of concerete paver block shall not be less than 40 MPa and weight 4.50 kg per No. confirming to IS: 1565 As Per Mord S.R..- 6.7 |
| 59 | Providing and laying vitrified floor tiles In different sizes (thickness to be specified by the manufacturer) with water absorption lass than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand),jointing with gray cement slurry@ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.11 .41A.1.1 Size of Tile 600x600 mm Double Charge |
| 60 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete D.S.R.-15.88 |
| 61 | Finishing walls with 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004,Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.13.48A.1 New work (Two or more coats applied @ 1.43 litre/ 10sqm. Over and including priming coat of exterior primerapplied @ 0.90 litre/10 sqm DSR 13.44.1 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysNov 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender