Tender For Repair/Maint To Chain Link Fencing, Barbed Wire, Boundary Wall, Jaffery Wall ,Iron Gates, Hardstanding And Allied Work In Zone A Area Of Age B/R-I Under Ge (C) Khadki.
Tender Value
1 Crore
Estimated cost
Bid Submission
07 Dec 2026
22 days left
EMD
1.75 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pune → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/Maint To Chain Link Fencing, Barbed Wire, Boundary Wall, Jaffery Wall ,Iron Gates, Hardstanding And Allied Work In Zone A Area Of Age B/R-I Under Ge (C) Khadki.
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches in soft /loose soil,n exc 1.5m wide and n exc 1.5m in depth ;for foundation etc.or for shafts well cesspit,maholes, pier holes etc.n exc 10 sqm on plan and n exc 1.50m in depth complete all as specified and directed by Engineer-in-Charge. |
| 2 | Returing, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cms in soft /loose soil, complete all as specified and directed by Engineer-in-Charge. |
| 3 | Removing excavated material not exceed 50 m depositing where directed level n exc 1.5 mtr above the starting point, complete all as specified and directed by Engineer-in-Charge. |
| 4 | M & L for PCC 1:4:8 type D2 using 40mm graded aggregate as in foundation filling and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 5 | Demolition of RCC of any description and in any position complete all as specified and directed by Engineer-in-Charge. |
| 6 | Use and waste of Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed by Engineer-in-Charge. |
| 7 | M & L for RCC (Nominal mix) Type B1 1:2:4 using 20mm graded stone aggregate as in coloumn,pillars,piers, posts and struts complete all as specified and directed by Engineer-in-Charge. |
| 8 | M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in lintels upto 1.5 clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers ,apex stones, bed plates, water troughs and the like including use of formwork (straight or curved) ,including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed by Engineer-in-Charge. Note :-reinforcement where provided shall be measured and paid seprately |
| 9 | Demolition of cement concrete (un- reinforced) of any description in ground floor and paving n.exc 15 cm thickness (below or above GL) , complete all as specified and directed by Engineer-in-Charge. |
| 10 | M & L for 100mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded crushed stone agg) as in sub base complete all as specified and directed by Engineer-in-Charge. |
| 11 | M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including dismantling of old U/s paver blocks complete all as specified and directed by Engineer-in-Charge. |
| 12 | M & L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, including dismantling of old U/s paver blocks complete all as specified and directed by Engineer-in-Charge. |
| 13 | M&L for Chequred cement concrete tiles 30cm X 30cm X 20mm thick, set, pointed & jointed in neat cement slurry in floors polished with grey cement & pigments layed over 20mm thick cement screed base (1:6) including dismantling of old U/s Chequered tiles complete all as specified and directed by Engineer-in-Charge. |
| 14 | M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in kerbs slightly rounded or chamfered angles sides of path complete all as specified and directed by Engineer-in-Charge. |
| 15 | M & L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms,gate vertical surfaces of any ht and like over 15mm thick cement plaster in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including demolition of existing granite or stone slabs of any type and position complete all as specified and directed by Engineer-in-Charge. |
| 16 | Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-Charge. |
| 17 | M & L for pre-cast cement concrete solid block masonry with solid block of the Type C-1, (1:3:6) (using 20mm graded aggregate) set in CM (1:6) complete all as specified and directed by Engineer-in-Charge. |
| 18 | M&L for Brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in old size bricks in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 19 | M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 20 | M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 but except stone complete all as specified and directed by Engineer-in-Charge. |
| 21 | Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified of random rubble walling, coursed, hammer dressing with maximum depression on face from straight edge held against the dressed surface n.exc 40mm on Granite/Trap stone complete all as specified and directed by Engineer-in-Charge. |
| 22 | M&L for Raised pointing to RR masonry in CM 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 23 | M&L for providing 35mm thick precast cement concrete louvres and jallies, type B0 1:2:4 (12.5mm graded aggregate) measured solid,including all mouldings but excluding frame and set in cm 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 24 | M & L for rendering 15 mm thick on fair faces of brick work block work stone work or concrete surfaces on walls in CM 1:6 finished even and fair without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 25 | M & L for Preparation of new surfaces (Plastered or un-plastered) of walls or RCC Jaffries and applying two coats of cement base paint over a coat of alkali Resistant primer complete all as specified and directed by Engineer-in-Charge. |
| 26 | M & L for complete removal of existing treatment on wall surfaces of any description plastered or unplastered surfaces of wall and applying two coats of cement base paint including Priming plastered and other surfaces with alkali resistant primer complete all as specified and directed by Engineer-in-Charge. Note;- (i) filling of cracks,holes and dents are includes in the same rates (ii) Proper curing with water to be done before and after application of 1st coat.(iii) height upto 15 mtr . |
| 27 | Dismantling fencing wire mesh, any type and size, complete all as specified and directed by Engineer-in-Charge. |
| 28 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed by Engineer-in-Charge. |
| 29 | Supply only Chain link MS galvanised fencing, any size or type, complete all as specified and directed. |
| 30 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge. |
| 31 | Dismantling post or struts (wood,steel or RCC ) any dsection ,including taking out embeded portion in concrete or masonry and making good disturbed ground complete all as specified and directed by Engineer-in-Charge. |
| 32 | Excavation in soft/loose soil in post holes n.exc 0.5 Cum getting out and removing surplus soil to a distance n.exc 50m and making good surface complete all as specified and directed by Engineer-in-Charge. |
| 33 | M & L for PCC 1:2:4 type B2 (using 40mm graded aggregate) as in fixing fencing post complete all as specified and directed by Engineer-in-Charge. |
| 34 | S&F for Mild steel screw bolts dia of neck 5 to 10mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,exc 5cm & n.exc 10 cm long complete all as specified and directed by Engineer-in-Charge. |
| 35 | S&F for MS hand rails, half rounded or other stock section or core for wooden hand rail straight portion, drilled and counter sunk for balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc,) including all necessary drilling bolting or riveting, etc and similar work conforming to Fe290 Gde 165 complete all as specified and directed by Engineer-in-Charge. |
| 36 | M&L for mild steel round bars 10mm dia and over , Fe-410 (Gde- E-250) quality -'A' or Fe-290 (Gde-E-165), cut to length, bent to shape required, including cranking, hooking ends, complete all as specified and directed by Engineer-in-Charge. |
| 37 | M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete all as specified and directed by Engineer-in-Charge. |
| 38 | S & F for mild steel framed work (Conforming to FE-290, Gde E-165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge. |
| 39 | S&F 1.25mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed by Engineer-in-Charge. |
| 40 | M&L for preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge. |
| 41 | M&L for preparation of old steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 42 | S & F in repair for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed. |
| 43 | Taking down eaves gutters and rainwater pipes (any size or pattern ),including all fittings,heads,shoes,bends,swan necks etc.including cleaning or refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 44 | S&F 110 mm dia PVC (SWR ) pipes Single socketed in any length with rubber rings ljoits fixed to walls complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 22 daysDec 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender