Tender For Live Line Back Pulling Of Earth Wire And Supply And Stringing Of 48 Fiber (Dwsm) Opgw, Fiber Optic Terminal Equipment For Connectivity Of 132Kv Dhekiajuli-Rowta Transmission Line
Tender Value
Ref. Documents
Estimated cost
Bid Submission
26 Nov 2026
12 days left
EMD
8.67 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Sonitpur → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Live Line Back Pulling Of Earth Wire And Supply And Stringing Of 48 Fiber (Dwsm) Opgw, Fiber Optic Terminal Equipment For Connectivity Of 132Kv Dhekiajuli-Rowta Transmission Line
BOQ
| Sl. No. | Item Description |
| 1 | 48 Fiber (DWSM) OPGW fibre optic cable |
| 2 | 48 Fiber Optic Approach Cable ( DWSM48F) |
| 3 | OPGW Suspension Assembly with twisted link c/w pre-formed armour rods and tower bond clamps |
| 4 | OPGW Double Tension Pass through Assembly |
| 5 | OPGW Double Tension Assembly for splicing location c/w pre-formed armour rods and tower bond clamps |
| 6 | OPGW Tension single dead- end set for termination/ run-in c/w pre-formed armour rods and tower bond clamps |
| 7 | OPGW Splicing Tension Assembly in Suspension tower |
| 8 | OPGW Vibration damper c/w pre-formed armour rods |
| 9 | Downlead clamp |
| 10 | OPGW Optical Splice Kit (48 Fibre) including Junction Box |
| 11 | OPGW Fiber Optic Distribution Panel Indoor Type 48F |
| 12 | Hardware set for above 48 Fiber, Fiber Optic Approach Cable vizties/clips/cleats, conduits, ducts, supports, fittings, accessories etc for extending OPGW from sub-station and tower/gantry to FODP at control/communication room by splicing fibers of OPGW with FOAC in joint box at tower/gantry and splicing FOAC in FODP at control/communication room. |
| 13 | Base Equipment (Common Cards,Cross Connect/Control Cards, Optical Base cards,Power supply cards, power cabling, other hardware & accessories including sub-Control Cards, DDF etc fully equipped with redundant control cards, Optical Base cards, Power Supply Cards. |
| 14 | Optical Interface/SFP for: S1:1 |
| 15 | Optical Interface/SFP for: S4:1 |
| 16 | SFP to support STM-16 upto 60km |
| 17 | Line Interface to support STM-16 upto 100km |
| 18 | E1 Interface card (Minimum 63 Interfaces per card) |
| 19 | Ethernet interfaces with minimum of 10/100/1000Mbps configurable with Layer-2 switching (Minimum 8 interfaces card) |
| 20 | 8 Port VOIP for remort locations |
| 21 | Analog Telephone (2-wire telephone for VOIP Gateway location) |
| 22 | Drop and Insert Multiplexer Base Equipment (Common CardsCross Connect/Control Cards, Optical Base cards,Power supply cards, power cabling, other hardware & accessories including sub-racks, patch cords, DDF etc fully equipped with redundant control cards, Optical Base cards, Power Supply Cards) |
| 23 | 2 wire (sub/sub) voice channel cards (min 8 channels per card) |
| 24 | 4 wire (E&M) voice channel cards (min 8 channels per card) |
| 25 | 2 wire (sub/Exch) voice channel cards (min 8 channels per card) |
| 26 | Asynchronous Sub-Channel Data Cards (V.24/V.28) minimum 4 channel per card with opto-coupler interface |
| 27 | Synchronous Data card(N*64Kbps) |
| 28 | Tele-protection signalling equipment complying IEC 60834 (8 commands) and having E1 and optical interface equipment (with voltage selection for commands with 48VDC/11)VDC/220VDC) |
| 29 | IEEE C37.94 for direct connection of line differential protection relays |
| 30 | For primary multiplexer,Drop/Insert |
| 31 | For SDH Equipment(including DDF patching facilities and other accessories |
| 32 | Main Distribution Frame(100 pair) |
| 33 | Pre connectorized optical patch cords(minimum 8 patch cords per station) |
| 34 | Firewall with deep inspection over IEC 104 |
| 35 | GPS CLOCK MTCTE certified |
| 36 | 48 Fiber (DWSM) OPGW fibre optic cable |
| 37 | 48 Fiber Optic Approach Cable ( DWSM48F) |
| 38 | OPGW Suspension Assembly with twisted link c/w pre-formed armour rods and tower bond clamps |
| 39 | OPGW Double Tension Pass through Assembly |
| 40 | OPGW Double Tension Assembly for splicing location c/w pre-formed armour rods and tower bond clamps |
| 41 | OPGW Tension single dead- end set for termination/ run-in c/w pre-formed armour rods and tower bond clamps |
| 42 | OPGW Splicing Tension Assembly in Suspension tower |
| 43 | OPGW Vibration damper c/w pre-formed armour rods |
| 44 | Downlead clamp |
| 45 | OPGW Optical Splice Kit (48 Fibre) including Junction Box |
| 46 | OPGW Fiber Optic Distribution Panel Indoor Type 48F |
| 47 | Hardware set for above 48 Fiber, Fiber Optic Approach Cable vizties/clips/cleats, conduits, ducts, supports, fittings, accessories etc for extending OPGW from sub-station and tower/gantry to FODP at control/communication room by splicing fibers of OPGW with FOAC in joint box at tower/gantry and splicing FOAC in FODP at control/communication room. |
| 48 | Base Equipment (Common Cards,Cross Connect/Control Cards, Optical Base cards,Power supply cards, power cabling, other hardware & accessories including sub-Control Cards, DDF etc fully equipped with redundant control cards, Optical Base cards, Power Supply Cards. |
| 49 | Optical Interface/SFP for: S1:1 |
| 50 | Optical Interface/SFP for: S4:1 |
| 51 | SFP to support STM-16 upto 60km |
| 52 | Line Interface to support STM-16 upto 100km |
| 53 | E1 Interface card (Minimum 63 Interfaces per card) |
| 54 | Ethernet interfaces with minimum of 10/100/1000Mbps configurable with Layer-2 switching (Minimum 8 interfaces card) |
| 55 | 8 Port VOIP for remort locations |
| 56 | Analog Telephone (2-wire telephone for VOIP Gateway location) |
| 57 | Drop and Insert Multiplexer Base Equipment (Common CardsCross Connect/Control Cards, Optical Base cards,Power supply cards, power cabling, other hardware & accessories including sub-racks, patch cords, DDF etc fully equipped with redundant control cards, Optical Base cards, Power Supply Cards) |
| 58 | 2 wire (sub/sub) voice channel cards (min 8 channels per card) |
| 59 | 4 wire (E&M) voice channel cards (min 8 channels per card) |
| 60 | 2 wire (sub/Exch) voice channel cards (min 8 channels per card) |
| 61 | Asynchronous Sub-Channel Data Cards (V.24/V.28) minimum 4 channel per card with opto-coupler interface |
| 62 | Synchronous Data card(N*64Kbps) |
| 63 | Tele-protection signalling equipment complying IEC 60834 (8 commands) and having E1 and optical interface equipment (with voltage selection for commands with 48VDC/11)VDC/220VDC) |
| 64 | IEEE C37.94 for direct connection of line differential protection relays |
| 65 | For primary multiplexer,Drop/Insert |
| 66 | For SDH Equipment(including DDF patching facilities and other accessories |
| 67 | Main Distribution Frame(100 pair) |
| 68 | Pre connectorized optical patch cords(minimum 8 patch cords per station) |
| 69 | Firewall with deep inspection over IEC 104 |
| 70 | GPS CLOCK MTCTE certified |
| 71 | Survey of Transmission line for live line OPGW |
| 72 | Fiber optic Approach Cable(DWSM Fiber) |
| 73 | OPGW Suspension Assembly with twisted link c/w pre-formed armour rods and tower bond clamps |
| 74 | OPGW Double Tension Pass through Assembly |
| 75 | OPGW Double Tension Assembly for splicing location c/w pre-formed armour rods and tower bond clamps |
| 76 | OPGW Tension single dead- end set for termination/ run-in c/w pre-formed armour rods and tower bond clamps |
| 77 | OPGW Splicing Tension Assembly in Suspension tower |
| 78 | OPGW Vibration damper c/w pre-formed armour rods |
| 79 | Downlead clamp |
| 80 | Installation of Joint Box Above ground (including Splicing and Testing) |
| 81 | Live line Backpulling of OPGW/earthwire and fresh laying of OPGW |
| 82 | To & Fro trasportation of tools and tackles for stringing work |
| 83 | OPGW Fiber Optic Distribution Panel Indoor Type 48F |
| 84 | Installation hardware set for above 48 Fiber, Fiber Optic Approach Cable vizties/clips/cleats, conduits, ducts, supports, fittings, accessories etc for extending OPGW from sub-station and tower/gantry to FODP at control/communication room by splicing fibers of OPGW with FOAC in joint box at tower/gantry and splicing FOAC in FODP at control/communication room. |
| 85 | CD, PMD and AP Pre and Post Test for Fiber OPGW |
| 86 | OPGW Drum Testing |
| 87 | Link Comissioning LSPM OTDR |
| 88 | Base Equipment (Common Cards,Cross Connect/Control Cards, Optical Base cards,Power supply cards, power cabling, other hardware & accessories including sub-Control Cards, DDF etc fully equipped with redundant control cards, Optical Base cards, Power Supply Cards. |
| 89 | Optical Interface/SFP for: S1:1 |
| 90 | Optical Interface/SFP for: S4:1 |
| 91 | SFP to support STM-16 upto 60km |
| 92 | Line Interface to support STM-16 upto 100km |
| 93 | E1 Interface card (Minimum 63 Interfaces per card) |
| 94 | Ethernet interfaces with minimum of 10/100/1000Mbps configurable with Layer-2 switching (Minimum 8 interfaces card) |
| 95 | 8 Port VOIP for remort locations |
| 96 | Analog Telephone (2-wire telephone for VOIP Gateway location) |
| 97 | Drop and Insert Multiplexer Base Equipment (Common CardsCross Connect/Control Cards, Optical Base cards,Power supply cards, power cabling, other hardware & accessories including sub-racks, patch cords, DDF etc fully equipped with redundant control cards, Optical Base cards, Power Supply Cards) |
| 98 | 2 wire (sub/sub) voice channel cards (min 8 channels per card) |
| 99 | 4 wire (E&M) voice channel cards (min 8 channels per card) |
| 100 | 2 wire (sub/Exch) voice channel cards (min 8 channels per card) |
| 101 | Asynchronous Sub-Channel Data Cards (V.24/V.28) minimum 4 channel per card with opto-coupler interface |
| 102 | Synchronous Data card(N*64Kbps) |
| 103 | Tele-protection signalling equipment complying IEC 60834 (8 commands) and having E1 and optical interface equipment (with voltage selection for commands with 48VDC/11)VDC/220VDC) |
| 104 | IEEE C37.94 for direct connection of line differential protection relays |
| 105 | For primary multiplexer,Drop/Insert |
| 106 | For SDH Equipment(including DDF patching facilities and other accessories |
| 107 | Main Distribution Frame(100 pair) |
| 108 | Pre connectorized optical patch cords(minimum 8 patch cords per station) |
| 109 | Firewall with deep inspection over IEC 104 |
| 110 | GPS CLOCK MTCTE certified Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysNov 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender