Tender For Balance Works Of Multipurpose Hostel For Girls At Marampilly, Perumbavoor (General Civil, Electrical, Fire Fighting And Phe Works)
Tender Value
54.09 Lakhs
Estimated cost
Bid Submission
25 Nov 2026
10 days left
EMD
50000
Bank guarantee accepted
Document Fee
2950
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ernakulam → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Balance Works Of Multipurpose Hostel For Girls At Marampilly, Perumbavoor (General Civil, Electrical, Fire Fighting And Phe Works)
BOQ
| Sl. No. | Item Description |
| 1 | CIVIL WORKS |
| 2 | 21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) |
| 3 | 21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 4 | OD143292/2026-2027:Providing and fixing windows & ventilators, fabricated from roll formed sections made of Galvanized steel, prepainted(base steel as per IS 513\\"D\\" quality, Galvanised as per IS 277 with zinc of 120 grams per sq. mtr) with total coated thickness of 0.60 mm. Coated sections should be painted with primer coat of Epoxy primer of 5-7 microns thick, finish painted with pollyster paint of 12-16 microns thick and back coated woth alkyd backer of 5-7 microns thick or powder coated withpure polyester powder coated up to 50-60 microns thick.Section for Shutter should be of 46mm x 46mm and External Frame should be of 46mm x 52mm. Section for Glass Beading should be of 18mm x 25mm and center mullion should be of 46mm x 70mm and 50mm x 50mm box sections for Louvered Ventilators. The Frame & Shutter Sections should be cut to length and mitre joined with Corner Bracket made of CRCA electroplated. Mullion Section should be joined with Frame/ Mullion using Nylon Mullion Cap, box sections for Ventilators should be joined with aluminium ‘L’ brackets and PVC glass holders will be used for Louvered Ventilators. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter, between frame and glazed shutter and both sides of fixed glass.Handle made of high grade Aluminium powder coated and with nylon receiver. Gaskets made of Ethyl Propylene Diamine Monomer (EPDM). Corner brackets made of CRCA with zinc phosphating. Mullion caps made of Glass filled nylon.The assembled outer frame should be fixed to brick/concrete masonry using nylon self-expanding caps driving MS elecroplated 80 mm long screws in to the caps through outer frames. Glazed shutters are connected to outer frames using GI powder coated friction hinges of 250mm long. The infill for shutter can be 4mm float glass of saint gobain/mosy make complete. |
| 5 | 50.12.2.5:Providing & fixing Poly carbonate multi wall plain sheet 8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size ( 5.5x55mm) with EPDM seal complete upto any pitch in horizontal /vertical / curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size and shapes where ever required. |
| 6 | OD143212/2026-2027:Providing and fixing bright finished brass door latch with brass patta and necessary screws etc. complete: 450x19 mm |
| 7 | OD143259/2026-2027:Providing and fixing bright finished stainless steel door latch with necessary screws etc. complete:12x19mm |
| 8 | 9.100.1:Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm |
| 9 | Water Supply And Sanitary works |
| 10 | 17.3.1 : Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid |
| 11 | 17.7.1 Providing and fixing wash basin with C.I. brackets , 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm |
| 12 | 17.10.1.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board |
| 13 | 18.52.1 Providing and fixing CP brass stop cock (concealed) of standared design and of approved make conforming to IS:8931- 15 mm nominal bore |
| 14 | Providing and fixing sanitary fixtures for handicapped toilet including one wash basin, one number pillar cock with aerator all other related fittings like CP brass bottle trap,CP brass angle valve, CP brass waste coupling, etc, one number EWC Cistern complete with fittings seat cover, one no. hinged rail 4 nos. of grab rails 60cm etc, designed for people with special needs comes with as per manufacturers specification including cutting and making good the walls and floors wherever required as directed by Engineer-in-Charge. Hindware Matrix Set, Hindware F650003CP or equivalent. |
| 15 | Providing and fixing CP brass sink cock of approved quality and specifications with water conservation mechanism as required by the Engineer in Charge.Model no: Hindware- F650023CP or equivalent. |
| 16 | Providing and fixing premium quality wall shower and shower arm with wall flanges of approved quality and specifications including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. Model no: Hindware- F160145CP or equivalent. |
| 17 | 50.17.1.5 : Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. |
| 18 | 18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore |
| 19 | 18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore |
| 20 | Providing and fixing C.P. brass pillar cock of approved quality conforming to IS standards and15 mm nominal bore.Model no: Hindware- F650003CP or equivalent. |
| 21 | Providing and fixing C.P. brass bottle trap of approved quality conforming to IS standards and 15 mm nominal bore |
| 22 | 50.17.1.1 Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge |
| 23 | Supplying and fixing liquid soap container including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.Model no:Hindware- F102018CP or equivalent. |
| 24 | 50.17.1.3 Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. |
| 25 | Supplying and fixing of centrifugal pump, with CI construction, CI impeller complete with motor, base plate, foundation bolts, nuts,pressure guage and all accessories. and working with 415V, 3ph and 50 Hz frequency including cost and conveyance of all materials,labour charges etc complete as directed by the Engineer in charge at all levelsCapacity : 139 LpmHead : 24m |
| 26 | Supplying, laying, and jointing schedule 40 UPVC ASTM pipe and Schedule 80 ASTM-UPVC specials of approved make such as tees elbows, unions,bends,sockets bends,flanges, reducers, end caps,saddles, plugs,coupling, etc. including cost of all jointing materials like solvent cement, bolts, nuts, rubber washers,ferrule,pipe supports, cost of extra wastage of fittings during laying of pipe line such as rectification and recharging of the existing line as and when required etc.hire of tools and plant, cost and conveyance of water for testing after connecting to mains including all testing pipe line to the specified hydrostatic test pressure,rectifying any leakage or defects etc. complete.as directed by Engineer-in-Charge for water supply.: 32 mm dia pipe |
| 27 | Supplying, laying, and jointing schedule 40 UPVC ASTM pipe and Schedule 80 ASTM-UPVC specials of approved make such as tees elbows, unions,bends,sockets bends,flanges, reducers, end caps,saddles, plugs,coupling, etc. including cost of all jointing materials like solvent cement, bolts, nuts, rubber washers,ferrule,pipe supports, cost of extra wastage of fittings during laying of pipe line such as rectification and recharging of the existing line as and when required etc.hire of tools and plant, cost and conveyance of water for testing after connecting to mains including all testing pipe line to the specified hydrostatic test pressure,rectifying any leakage or defects etc. complete.as directed by Engineer-in-Charge for water supply.: 40 mm dia pipe |
| 28 | Supplying, laying, and jointing schedule 40 UPVC ASTM pipe and Schedule 80 ASTM-UPVC specials of approved make such as tees elbows, unions,bends,sockets bends,flanges, reducers, end caps,saddles, plugs,coupling, etc. including cost of all jointing materials like solvent cement, bolts, nuts, rubber washers,ferrule,pipe supports, cost of extra wastage of fittings during laying of pipe line such as rectification and recharging of the existing line as and when required etc.hire of tools and plant, cost and conveyance of water for testing after connecting to mains including all testing pipe line to the specified hydrostatic test pressure,rectifying any leakage or defects etc. complete.as directed by Engineer-in-Charge for water supply.:50 mm dia pipe |
| 29 | Supplying, laying, and jointing schedule 40 UPVC ASTM pipe and Schedule 80 ASTM-UPVC specials of approved make such as tees elbows, unions,bends,sockets bends,flanges, reducers, end caps,saddles, plugs,coupling, etc. including cost of all jointing materials like solvent cement, bolts, nuts, rubber washers,ferrule,pipe supports, cost of extra wastage of fittings during laying of pipe line such as rectification and recharging of the existing line as and when required etc.hire of tools and plant, cost and conveyance of water for testing after connecting to mains including all testing pipe line to the specified hydrostatic test pressure,rectifying any leakage or defects etc. complete.as directed by Engineer-in-Charge for water supply.: 65 mm dia pipe |
| 30 | Supplying, laying, and jointing schedule 40 UPVC ASTM pipe and Schedule 80 ASTM-UPVC specials of approved make such as tees elbows, unions,bends,sockets bends,flanges, reducers, end caps,saddles, plugs,coupling, etc. including cost of all jointing materials like solvent cement, bolts, nuts, rubber washers,ferrule,pipe supports, cost of extra wastage of fittings during laying of pipe line such as rectification and recharging of the existing line as and when required etc.hire of tools and plant, cost and conveyance of water for testing after connecting to mains including all testing pipe line to the specified hydrostatic test pressure,rectifying any leakage or defects etc. complete.as directed by Engineer-in-Charge for water supply.: 80 mm dia pipe |
| 31 | 18.17.6Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 80mm nominal bore |
| 32 | 18.17.5Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 65mm nominal bore |
| 33 | 18.17.4Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 50mm nominal bore |
| 34 | 18.17.3Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 40mm nominal bore |
| 35 | 18.17.2Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 32mm nominal bore |
| 36 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soilPipes, cables etc, not exceeding 80 mm dia |
| 37 | PORTABLE FIRE EXTINGUISHERS |
| 38 | od7476/2025_2026Refilling of existing installed of ABC type Fire Extinguisher 6 Kg Capacity made of Mild steel body, with opening and closing lever of squeeze grip type with Mono Ammonium Phosphate based Dry Chemical Powder as per IS 14609 with ISI Mark for Fighting ABC Class of Fire, with Co2 Gas Cartridge as per IS: 4947 with ISI mark, complete with wall bracket. The Extinguisher will be Manufactured Strictly as per IS: 15683:2006 with ISI mark. (Refilling shall be done based on the date of expiry on the extinguisher) |
| 39 | SIGNAGES |
| 40 | od10815/2025_2026Supply and installation of glow signage (photoluminescent) such as Fire Duct/Fire Lift/Staircase signage etc. of standard size (500*200 MM) as per NBC 2016 and conforming to IS 9457, IS 12349, IS 12407 design/ colour code on 3 mm thick aluminium composite panel. The signage will be either fixed on the wall with the help of screws & double tape or hanged from the false ceiling with the help of chain & screws etc. complete as required as per the technical specification. |
| 41 | FIRE HYDRANT SYSTEM |
| 42 | Supply, installation, testing and commissioning of electric driven pump set (terrace pump) suitable for automatic operation and consisting of following: Monoblock Pump rated for 450lpm, 40m head C.I body, bronze impeller, SS shaft with mechanical seal, volute type with suitable HP SQ cage induction motor, suitable for operation on 415V, 3phase 50Hz, AC with IP 55 class of protection for enclosure, horizontal foot mounted type with class F insulation.M.S. fabricated common base plate and suitable cement concrete foundation, suitable capacity DOL starter, incomer cable to the starter from the electrical panel, outgoing cable from starter to pump, cable terminations, earthing and all other related electrical items shall be included in this line at no additional cost, complete as required as per the technical specification. |
| 43 | Supply, installation, testing and commissioning of butterfly valve of 100 mm diameter, PN 16, with Cast iron/Carbon steel body, SS disc complete with all accessories including flanges, rubber gasket, GI bolts, GI nuts, washers etc. complete as required as per the technical specification and conforming to IS 13095. |
| 44 | Supply, installation, testing and commissioning of 20 mm (nominal internal) dia gun metal globe valve & nozzle for connecting to First-aid Hose Reel 20 mm (nominal internal) water hose. |
| 45 | Supply, installation, testing and commissioning single headed internal hydrant valve with instantaneous Gunmetal coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank cap and chain, complete as required as per technical specification. |
| 46 | Supply, installation, testing and commissioning of 63 mm dia, 15 mtr. Long RRL hose pipe with 63 mm dia Male and Female Gun metal couplings duly binded with GI/MS/SS wire, rivets etc. conforming to IS 636 (type-1) as required as per technical specification. |
| 47 | Supply, installation, testing and commissioning of 63 mm dia Gun metal branch pipe with 20 mm (nominal internal diameter) size Gun Metal nozzle conforming to IS 903, suitable for instantaneous connection to inter-connect hose pipe coupling as required as per technical specification. |
| 48 | Supply, installation, testing and commissioning of 2-WAY FIRE BRIGADE inlet connection made of CI Body, 100mm dia. flanged inlet with 2 Nos. of inbuilt gunmetal, NRV (Body type) with PVC Blank cap & Chain complete with GI nuts, bolts, gasket etc as required as per technical specification. |
| 49 | Supply, installation, testing and commissioning of Gun metal Air release valve, 25mm male threaded inlet, complete with all accessories as required as per the technical specification. |
| 50 | PORTABLE FIRE EXTINGUISHERS |
| 51 | Supply and installation of ABC Stored pressure type Fire Extinguisher 6 Kgs Capacity Mono Ammonium Phosphate based Dry Chemical Powder as per IS 14609 with ISI Mark for Fighting ABC Class of Fire, stored Pressure type of Mild steel body pressurized by Nitrogen Gas. The Extinguisher shall have pressure gauge for indicating inside pressure with opening and closing lever of squeeze grip type withtamper proof seal, complete with wall bracket. The Extinguisher should be manufactured strictly as per IS: 15683:2018 with ISI mark. |
| 52 | Supply and installation of Carbon-dioxide extinguisher of ISI marked 4.5 Kg capacity made of high pressure seamless steel cylinder (CCE marked ) complete with wheel type valve with one meter long braided high pressure discharge hose complete in all respects including initial fill with CO2 gas, conforming to IS:15683:2018 complete as required as per the technical specification. |
| 53 | SIGNAGES |
| 54 | Supply and installation of glow signage (photoluminescent) such as Fire Duct/Fire Lift/Staircase signage etc. of standard size (500*200 MM) as per NBC 2016 and conforming to IS 9457, IS 12349, IS 12407 design/ colour code on 3 mm thick aluminium composite panel. The signage will be either fixed on the wall with the help of screws & double tape or hanged from the false ceiling with the help of chain & screws etc. complete as required as per the technical specification. |
| 55 | REPAINTING |
| 56 | 13.50.3Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron /steel works |
| 57 | 13.99.1Painting with synthetic enamel paint of approved brand and manufacture ofrequired colour to give aneven shade :One or more coats on old work |
| 58 | (SH : DG SET)(Sl No. 1) Supply, Installation, Testing and Commissioning of outdoor 82.5 KVA prime rated D.G Set with acoustic enclosure and Control panel ,protection and digital metering,controls and interlocks, CTs and transducers for all metering and protection and suitable FP MCCB etc. , including antivibration mountings, exhaust silencer and exhaust pipe conforming to latest environment protection regulations for emission and noise levels complete with , water/ coolant cooled, (radiator type) four stroke, electric start conforming to BS: 5514 82.5 KVA prime rating, brushless, self excited, self regulated and suitable for continuous operation at 1500RPM, generating 415 V+/-5% Volts at 0.8 p.f (lag), 50Hz,3 phase, 4 wire system generally conforming to BS: 2613 & IS: 4722. Both Engine and Alternator shall be mounted on common channel iron base frame, and with standard accessories such as lead acid batteries and engine driven battery charger along with leads,battery stand, necessary control wiring with control cables, first fill of lubricating oil, and earthing as per standards Fuel tank , fuel piping from fuel tank to Engine, Residential silencer, suitable size Cable termination box with extended Alternator terminal with bus bars etc as required and as per specifications.Rate shall be inclusive of all the civil work including RCC foundation. The work should be as per Electrical Inspectorate/ Pollution control board standards. |
| 59 | (SH : CABLES AND CABLING) (Sl No. 5 - 19)SUPPLY Supply of following size 1.1 KV grade XLPE insulated, PVC sheathed, armoured Aluminium /copper conductor cable conforming to IS 7098 (Part 1) amended upto date. |
| 60 | 3.5C 185 Sq.mm Al |
| 61 | 3.5C 95 Sq.mm Al |
| 62 | 3.5C 70 Sq.mm Al |
| 63 | 3.5C 35 Sq.mm Al |
| 64 | 4C 16 Sq.mm Al |
| 65 | 4C 6 Sq.mm Al |
| 66 | 2C 6 Sq.mm Al |
| 67 | 3C x 2.5 sqmm Cu |
| 68 | 4C x 1.5 sqmm Cu |
| 69 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 70 | 3.5C 185 Sq.mm Al |
| 71 | 3.5C 95 Sq.mm Al |
| 72 | 3.5C 70 Sq.mm Al |
| 73 | 3.5C 35 Sq.mm Al |
| 74 | 4C 16 Sq.mm Al |
| 75 | 4C 6 Sq.mm Al |
| 76 | 2C 6 Sq.mm Al |
| 77 | 3C x 2.5 sqmm Cu |
| 78 | 4C x 1.5 sqmm Cu |
| 79 | LAYING Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall or surface as required. |
| 80 | Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 81 | Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) |
| 82 | Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) |
| 83 | Laying of one number PVC insulated and PVC sheathed armoured power cable of 1.1kV grade fo the following sizes in ground including excavation ,sand cushioning , providing protective covering and refilling the trench etc. as required |
| 84 | Upto 35 sq. mm |
| 85 | Above 35 sq. mm and upto 95 sq. mm |
| 86 | Above 95 sq. mm and upto 185 sq. mm |
| 87 | Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.'Upto 35 sq. mm |
| 88 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. |
| 89 | Upto 35 sq mm |
| 90 | Above 35 sq. mm and upto 95 sq. mm |
| 91 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.Upto 35 sq mm |
| 92 | Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size on cable tray as required. |
| 93 | Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 94 | Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) |
| 95 | Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) |
| 96 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc as required |
| 97 | 50 mm |
| 98 | 100 mm |
| 99 | Providing, laying and fixing following dia RCC pipe NP 2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required.100 mm dia |
| 100 | Fabrication, supply and installation of following size of Ladder GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with MS suspenders and painting etc as required |
| 101 | 300 MM WIDTH X 50 MM DEPTH X 2MM THICK |
| 102 | 150 MM WIDTH X 50 MM DEPTH X 2 MM THICK |
| 103 | Supply, fabricating and installing MS items such as Tees/ angles/ channels etc. on floor/ ceiling/ wall including necessary civil work such as grouting, finishing etc. and painting with two coats of primer and two coats of synthetic enamel paint as required |
| 104 | Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required. |
| 105 | Supply and fixing of chequered plate of 6 mm thick including cutting to required size using gas cutter and lay the same over the trench, fixing of nosing angle and supports for chequered plate, related civil works, finishing etc. and painting with two coats of enamel paint over one coat of Zinchromate primer as required. |
| 106 | Providing & fixing Fire Barrier mortar with minimum 2 hours fire rating when tested in accordance with BS 476 part 20 and UL 1479 for horizontal openings in fire rated floors or slabs and vertical openings in walls for passing service shafts. The service lines could be of various types like electrical cables trays, metal pipes, GI Ducts for AC, etc.The mortar shall have minimum hardened density of 0.8 g/cm3 and It should have a compressive strength of 2.9N/Sq mm . The product shall be Smoke & Air Seal and 30 years Age tested as per Dafstb and DIBT standards. The product shall be tested and approved by third party agencies such as UL and FM. The mortar should be tested in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. The product shall bear the UL and FM approval logo on the packing where applicable. |
| 107 | (SH : WIRING AND ACCESSORIES)Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. (Note:The total distance from the switch box to the point will not exceed 5mtr, incase if length increases above 5 metres, the wiring shall be measured under item 26) |
| 108 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.. (Note:The total distance from the switch box to the point will not exceed 5mtr) |
| 109 | Group controlled light point with 1.5 sq. mm wire - Wiring for Group controlled light point (from one point to another point) with 3X 1.5 sq. mm PVC insulated, (FRLS), copper conductor cable in surface/recessed mounted rigid medium class 20mm PVC conduit with all accessories as required. ( Note: This item does not include the cost of MCB or 16Amp/ 6Amp one way switches. The total distance from one point to another point will not exceed 5meters. In case if the total length increases 5meters, the additional lengtth shall be measured under item 4.4.1. The distance from DB to 1st point will be measured under item point wiring. |
| 110 | Circuit wiring -Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 111 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 112 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 113 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 114 | Supplying and fixing following modular switch/ socket with modular plate & cover on surface or in recess, including proving and fixing suitable size GI box,inter connection etc as required complete. |
| 115 | 15/16 amp switch |
| 116 | 6 pin 15/16 amp socket outlet |
| 117 | Telephone socket outlet |
| 118 | TV antenna socket outlet |
| 119 | Bell push |
| 120 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 121 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). |
| 122 | Supply, fixing of Network point, UTP RJ45, CAT 6 modular type socket in existing GI box, inter connection etc as required complete. |
| 123 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 124 | 20 mm |
| 125 | 25 mm |
| 126 | 32 mm |
| 127 | Supplying and fixing following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB’s, with provision of FP 16 KA MCCB as incomer, interconnection between incomer MCCB and bus bars (but without MCB’s/ MCCB) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 Way TP |
| 128 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB’s (but without MCB’s and incomer ) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door |
| 129 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 130 | 4 way (4 + 12), Double door |
| 131 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator)2 + 12 way, Double door |
| 132 | Supply and fixing of following rating residual current circuit breaker with MCB having earth leakage and overload protection (RCCB+MCB) as per specification as required |
| 133 | 2 pole 25 amps. (415 Volts), 30mA sensitivity. |
| 134 | 4 pole 25 amps. (415 Volts), 100mA sensitivity. |
| 135 | 4 pole 25 amps. (415 Volts),30mA sensitivity. |
| 136 | 4 pole 40amps. (415 Volts),30mA sensitivity. |
| 137 | 4 pole 63amps. (415 Volts),100mA sensitivity. |
| 138 | Supply and fixing of following rating, 10 KA, Miniature Circuit Breakers as required. |
| 139 | 6A to 32A, SP, C-CURVE |
| 140 | 40 A to 63 A TP MCB, C-CURVE |
| 141 | Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.100 A, 30KA, FP MCCB |
| 142 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 143 | 40 amps |
| 144 | 63 amps |
| 145 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 146 | Supply and fixing of 32A DP isolator with DP enclosure |
| 147 | Supply and fixing of 32A FP isolator with FP enclosure |
| 148 | Supply of following sizes of 1200 mm sweep. 5 star rated ceiling fan, with double ball bearing, Aluminium pressure die cast body with Aluminium blades, canopies, hanging shackle, 30 cm down rod and without speed regulator suitable for 240V 50 HZ, AC supply confirms to IS 374/1979 as required complete. (Make crompton-High breeze or equivalent approved make). . |
| 149 | Supply of 250 mm sweep,900 rpm light duty exhaust fan in plastic body with self opening louvers working on 230 V AC supply complete with all accessories as required. (Crompton Brisk Air or equivalant approved make) |
| 150 | Supply of 380 mm sweep heavy duty exhaust fan indie cast aluminium with self opening louvers working on 230 V AC supply complete with all accessories as required. (Crompton EXHD-380-6-1 or equivalant approved make) |
| 151 | ITC LIGHT FITTINGS AND FANSInstallation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 152 | Installation, testing and commissioning of fluorescent fittings with down rod and copper wiring - Installation testing and commissioning of prewired fittings of all types including complete with all accessories, lamps etc. including supplying painting and wiring the down rod upto 2x60 cm length and connections with using 3 runs of 1.5 sqmm FR PVC insulated stranded copper conductor as required. |
| 153 | Installation, testing and commissioning of High bay/LED/ FLOOD type fittings on wall/Column/truss/false ceiling using suitable MS clamps, nuts, bolts/ 20mm heavy duty GI chain/ pipe (upto 50cm)etc including connections with 3C 1.5 Sq.mm PVC insulated flexible copper conductor cable as required. |
| 154 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
| 155 | Installation, testing and commissioning of exhaust fan upto 380mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing & commissioning etc as required. |
| 156 | Numbering of ceiling fan / exhaust fan/ fluorescent fitting as required. |
| 157 | Supply, installation, testing and commissioning of 3.0 meter long GI pole suitable for mounting 18W CFL luminarie with built- in control box( control box should be prewired with MCB, terminal connectors for loop-in, loop-out, service door ), base plate and , concealed wiring with 3Cx 2.5 sq.mm copper wire from the control box to light fixture, complete with all necessary accessories as required including foundation with M25 as per design drawing , excavation,plastering,painting,finishing etc as required complete and directed by the engineer in charge. Note:Incoming and outgoing cable at termination box shall be terminated with glands properly.(Pole Model : K-Lite : MC-6005 or other equivalent approved make) |
| 158 | Supply |
| 159 | (SH : EARTHING AND SAFETY EQUIPMENTS)(Sl No. 59 - 62)Earthing with C.I. earth pipe 4 metre long, 100 mm dia including accessories, and providing masonry enclosure with heavy duty CI cover plate of 300X300mm having locking arrangement and watering pipe etc. with 64kg charcoal/ coke and 5kg salt as required. (As per IS 3043 ammended uptodate) |
| 160 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 161 | Providing and fixing GI/Cu strip/wire on surface or in recess for connections etc. as required. |
| 162 | 25mm X 6mm GI |
| 163 | 3.15mm Cu (10 SWG) |
| 164 | 4mm GI (8 SWG) |
| 165 | Supplying and laying G.I/Copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 166 | 25mm X 6mm GI |
| 167 | 3.15mm Cu (10 SWG) |
| 168 | 4mm GI (8 SWG) |
| 169 | (SH : LIGHTNING PROTECTION)(Sl No. 63 - 66) |
| 170 | Providing and fixing Test box with testing joint made of 30x3mm thick GI strip 125mm long with 4No. G.I. bolts, nuts, check nuts, spring washer etc. complete as required. |
| 171 | Providing and laying GI tape 32mm x 6mm thick from earth electrode directly in ground as required. |
| 172 | SCHEDULE B -(SH : CABLES AND CABLING) (Sl No. 5 - 19)SUPPLY Supply of following size 1.1 KV grade XLPE insulated, PVC sheathed, armoured Aluminium /copper conductor cable conforming to IS 7098 (Part 1) amended upto date. |
| 173 | 3.5C 185 Sq.mm Al |
| 174 | 3.5C 35 Sq.mm Al |
| 175 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 176 | 3.5C 35 Sq.mm Al |
| 177 | LAYING Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall or surface as required. |
| 178 | Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 179 | Laying of one number PVC insulated and PVC sheathed armoured power cable of 1.1kV grade fo the following sizes in ground including excavation ,sand cushioning , providing protective covering and refilling the trench etc. as required |
| 180 | Upto 35 sq. mm |
| 181 | Above 95 sq. mm and upto 185 sq. mm |
| 182 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. |
| 183 | Above 95 sq. mm and upto 185 sq. mm |
| 184 | (SH : WIRING AND ACCESSORIES) |
| 185 | Supply & fixing Computer points with 3 nos 3 pin 5/6A socket with 2no.5/6A switch in existing GI boxes, its interconnections etc as required complete. (Note: 2 nos 5/6Asocket fixed at 60cm above FFL and 2 nos 6A switch with 1no 5/6A socket at 1m above FFL)Note: The rate shall be inclusive of dismantling of damaged components such as wires, switches, exclusive of back boxes |
| 186 | Supply, fixing of Network point, UTP RJ45, CAT 6 modular type socket in existingGI box, inter connection etc as required complete. |
| 187 | (SH : LIGHT FIXTURES AND FANS)Supply of 12W (+/-2), High efficient surface mounted LED round downlighter with white powder coated, Aluminium die cast aluminium housing. System efficacy not less than100 lm/w, pf > 0.95, THD 80, SDM<5, life - 50000 hrs @L70, ccr 5700+300 K and EMI/EMC compatible, surge protection: at least 4 KV inbuilt with the electronic drive system. |
| 188 | Supply of surface mountable 10W LED batten , with aluminum extrusion slim shape type led light fixtures, and having complete with all necessary accessories 6500k;PF>0.95;THD<10% prewired upto a terminal block including one number of 10W LED lamp, necessary accessories and connections. |
| 189 | Supply of 20W Surface/Suspended Mounted LED Batten of maximum wattage below 20W with Systemefficacy of more than 120 lm/W and lumen output of luminaire greater than 2160 lumen for use on 230V AC supply. LED luminaire shall have sleek design with Extruded Aluminum Section. The luminaire shall have Optically Efficient Polycarbonate Diffuser for Uniform illumination and wider light distribution. The LED shall be compliant with LM80 standard with Useful L70 life of 50000 Hrs tested at maximum current. The CRI of Minimum80 and 4 KV internal surge protection. Power factor greater than 0.95 ,CCT 5000-6000 K,ripplefactor<5 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire andEMI/EMC compatible |
| 190 | Supply of 40W Surface/Suspended Mounted LED Batten of maximum wattage below 40W with Systemefficacy of more than 120 lm/W and lumen output of luminaire greater than 4320 lumen for use on on230 V AC supply. LED luminaire shall have sleek design with Extruded Aluminum Section. Theluminaire shall have Optically Efficient.Polycarbonate Diffuser for Uniform illumination and wider lightdistribution. The LED shall be compliant with LM80 standard with Useful L70 life of 50000 Hrs tested atmaximum current. The CRI of Minimum 80 and 4 KV internal surge protection. Power factor greaterthan 0.95 ,CCT 5000-6000K,ripple factor<5, and total harmonic distortion (THD) of less than 10%should be integral to the luminaire and EMI/EMC compatible |
| 191 | Supply of 36/40W LED street light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing,acrylic cover complete with THD less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer) |
| 192 | Supply of 400 mm size wall mounting oscillating type fan having three speed control, oscillation control at bottom and suitable for operation on single phase 230 volt, 50Hz AC supply complete with continuous duty motor, chrome plated front and rear guards and all accessories as required complete. |
| 193 | Installation, testing and commissioning of Wall fan, including all the supports as required and wiring using 3 runs of 1.5 sqmm FR PVC insulated stranded copper conductor etc complete |
| 194 | (SH : EXTERNAL LIGHTING SYSTEM)Supply, Installation, Testing and Commissioning of LED bollard, IP 65, made out of diecast Aluminium /MS, antirust treated, with polyurethane coating required foundation bolts and base plate, of height 1 (+/-0.5)m prewired with terminal connectors for loop-in-loop-out.The item includes LED module, along with driver of approved make, system wattage of 10+/-2W, with efficacy greater than 60,with THD<10%, power factor > 0.9,rated life of L70 @ 50,000 hours,CCT 3000K, with CRI >=80, with all necessary accessories as required complete. |
| 195 | Supply, Installation, Testing and Commissioning of LED post top luminaire, IP 65, made out of diecast Aluminium /MS, antirust treated, with polyurethane coating required foundation bolts and base plate, prewired with terminal connectors for loop in-loop-out. The item includes LED module, along with driver of approved make, system wattage of 20+/-5W, system efficacy shall be >=100lm/W, with power factor > 0.9,rated life of L70 @ 50,000 hours, CCT -as per site requirement, with CRI >=80, with all necessary accessories as required complete. |
| 196 | SCHEDULE C |
| 197 | Supply & fixing Computer points with 3 nos 3 pin 5/6A socket with 2no.5/6A switch in existing GI boxes, its interconnections etc as required complete. (Note: 2 nos 5/6A socket fixed at 60cm above FFL and 2 nos 6A switch with 1no 5/6A socket at 1m above FFL) Note: The rate shall be inclusive of dismantling of damaged components such as wires, switches, exclusive of back boxes |
| 198 | Supply, fixing of Network point, UTP RJ45, CAT 6 modular type socket in existingGI box, inter connection etc as required complete. Please Enable Macros to View BoQ information |
| 199 | Supply, fixing of Network point, UTP RJ45, CAT 6 modular type socket in existingGI box, inter connection etc as required complete. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender