Road Transport and Highways Government Departments Closing in 4 days TDR #58387264

Tender For Improvement Of Alternate Road To Maa Kamakhya Temple By Providing Reinforced Cement Concrete Bridge To Eliminate Hair Pin Bend, Rock Fall Protection & Improvement Of Junction At Entry Point Under Sopd-G For The Year 2023-24.(Construction O

Issued by Government Departments · Kamrup Metro, Assam
Tender Value
Ref. Documents
Estimated cost
Bid Submission
25 Nov 2026
4 days left
EMD
4.92 Lakhs
Bank guarantee accepted
Document Fee
7395
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Kamrup Metro → Assam
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Improvement Of Alternate Road To Maa Kamakhya Temple By Providing Reinforced Cement Concrete Bridge To Eliminate Hair Pin Bend, Rock Fall Protection & Improvement Of Junction At Entry Point Under Sopd-G For The Year 2023-24.(Construction Of Office Building For The Executive Engineer,Pwrd, Jalukbari Division, And 2 (Two) Nos. Of Offices For The Assistant Executive Engineers, Pwrd, Jalukbari Territorial Road Division At The 2Nd Floor Of Cdc, Jalukbari Office

BOQ

Name of Work:- Improvement of Alternate Road to Maa Kamakhya Temple by Providing RCC Bridge to Eliminate Hair Pin Bend, Rock Fall Protection & Improvement of Junction at Entry Point under SOPD-G for the Year 2023-24.(Construction of Office Building for the Executive Engineer,PWRD, Jalukbari Division, and 2 (two) Nos. of Offices for the Assistant Executive Engineers, PWRD, Jalukbari Territorial Road Division at the 2nd Floor of CDC, Jalukbari Office
Sl. No. Item Description
1Civil Works (Schedule Works)
2Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand)
315 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand)
4Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded.star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Frame size 65 x 150 mm
5Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded.star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dashfasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Frame size 45 x 85 mm
6Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). 35 mm thick
7Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). 35 mm thick
8Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.
9Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size
10Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm
11Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shadecomplete.
12Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)
13Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing completewith :Makrana white second quality
14Extra for pre finished nosing to treads of steps of marble stone.
15Mirror polishing on marble work/Granite work/stone work where everrequired to give high gloss finish complete.
16Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.
17Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).
18Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge.
19Providing and fixing Scaffolding net of required width made of high density Polyethylene UV stabilized knitted on warp knitting machines having density 100grams/sqm and shading coefficient minimum 75% around the construction site/ for vertical extension as per requirement including fastening/tying with building/scaffolding pipes or with any other fixtures etc. complete as per direction of Engineer-in-Charge. (One time payment shall be made for providing Scaffolding net from start of work till completion of work including shifting if any. The Scaffolding net shall be the property of the contractor on completion of the work)
20Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
21Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer
22Wall painting with acrylic emulsion paint of approved brand andmanufacture to give an even shade :Two or more coats on new work
23Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied
24Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works
25Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
26Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portionPolyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)
27For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)
28Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight notless than 12.50 kg/sqm)
29Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.Upto 5mm depth and 5 mm width
30Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. .
31Centering and shuttering including strutting, propping etc. and removalof form forColumns, Pillars, Piers, Abutments, Posts and Struts Mullion post
32Centering and shuttering including strutting, propping etc. and removalof form forLintels, beams, plinth beams, girders, bressumers and cantilevers
33Centering and shuttering including strutting, propping etc. and removalof form for Suspended floors, roofs, landings, balconies and access platform
34Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering,finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate. 20 mm nominal size derived from natural sources)
35Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
36Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.
37Providing and fixing bright finished brass tower bolts (barrel type) withnecessary screws etc. complete : 250x10 mm
38Providing and fixing bright finished brass tower bolts (barrel type) withnecessary screws etc. complete : 100x10 mm
39Providing and fixing bright finished brass butt hinges with necessaryscrews etc. complete : 125x85x5.5 mm (heavy type)
40Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm
41Providing and fixing chromium plated brass handles with necessaryscrews etc. complete: 125 mm
42Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
43Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete
44Structural steel work riveted, bolted or welded in built up sections, trussesand framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
45Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 withcharacteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately).0.56 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm.
46Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
47Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.
48Civil Works (Non Schedule Works)
49Providing and fixing modular partition wall of overall height 1.80 m, comprising a 75 mm thick timber frame fabricated with 19 mm thick solid plywood, arranged in a grid of 0.60 m × 0.60 m. The lower 1.20 m height shall be finished with 12 mm thick solid plywood fixed on both sides of the frame. The upper 0.60 m height shall consist of 5 mm thick fixed clear glass securely fixed with approved glazing beads and accessories. The exposed plywood surfaces shall be finished with 1.5 mm thick decorative laminate (mica) of approved shade and make, pasted using approved synthetic adhesive to provide a smooth and even finish. The work shall include all necessary screws, fasteners, adhesives, edge beading, polishing of exposed edges, cutting, fitting, and all incidental materials and labour required for complete installation as directed by the Engineer-in-Charge.
50Providing and fixing modular toilet cubicle/cabinet of overall size 1.00 m (Width) × 1.50 m (Length) × 2.10 m (Height), fabricated using 18 mm thick single extruded solid WPC (Wood Plastic Composite) plain white colour boards fixed over a supporting framework made of 40 mm × 40 mm MS L-angle sections, complete with anti-corrosive primer and two coats of synthetic enamel paint. The cubicle shall be provided with a 650 mm wide WPC door of matching thickness, complete with approved quality SS hinges, tower bolt, aldrop, door handle, lock, door stopper, and all necessary hardware fittings. All exposed WPC surfaces shall be finished with 1.0 mm thick decorative laminate of approved shade and make, fixed with approved synthetic adhesive to provide a smooth and durable finish. The work shall include all necessary screws, fasteners, edge finishing, cutting, fitting, sealing, and all incidental materials and labour required for complete installation as per the approved drawing and as directed by the Engineer-in-Charge.
51Providing and fixing of all exposed WPC surfaces shall be finished with 1.5 mm thick decorative laminate of an approved shade, colour, pattern, and make. The laminate shall be securely fixed using an approved synthetic adhesive to provide a smooth, uniform, durable, and aesthetically pleasing finish, complete in all respects and as directed by the Engineer-in-Charge.
52Plumbing & Sanitary Works ( Schedule Works)
53Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.1 Kitchen sink with drain board 510x1040 mm bowl depth 250 mmPantry
54Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.17.28.2 Flexible pipe 40 mm dia
55Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
56Providing and fixing toilet paper holder : C.P. brass
57Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe withclamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 25 mm nominal dia Pipes
58Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe withclamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 32 mm nominal dia Pipes
59Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe withclamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 40 mm nominal dia Pipes
60Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe withclamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 50 mm nominal dia Pipes
61Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the wallsetc. 20 mm nominal dia Pipes
62Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the wallsetc. 25 mm nominal dia Pipes
63Providing and fixing uplasticised PVC connection pipe with brassunions : 45 cm length 15 mm nominal bore
64Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore
65Providing and fixing uplasticised PVC connection pipe with brassunions : 45 cm length 15 mm nominal bore
66Providing and fixing brass stop cock of approved quality : 20 mm nominal bore
67Providing and fixing on wall face unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.75 mm diameter
68Providing and fixing on wall face unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.110 mm diameter
69Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conformingto IS : 13592 Type A, including jointing with seal ring conforming toIS : 5382, leaving 10 mm gap for thermal expansion.Coupler 75 mm
70Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conformingto IS : 13592 Type A, including jointing with seal ring conforming toIS : 5382, leaving 10 mm gap for thermal expansion.Coupler 110 mm
71Single tee with door 75x75x75 mm
72Single tee with door 110x110x110 mm
73Single tee without door 75x75x75 mm
74Single tee without door110x110x110 mm
75Bend 87.5° 75 mm bend
76Bend 87.5° 110 mm bend
77Plumbing & Sanitary Works (Non Schedule Works)
78Providing and fixing CP 2 in 1 Bib Cock. Make: Jaquar or Equivalent as directed by Engineer in Charge
79Providing and fixing CP Health Faucet .Make: Jaquar or Equivalent as directed by Engineer in Charge
80Providing and fixing Floor mounted SIngle piece EWC .Make: Jaquar or Equivalent as directed by Engineer in Charge
81Providing and fixing Table Top Wash Basin .Make: Jaquar or Equivalent as directed by Engineer in Charge
82Providing and fixing Conceal single lever Bib cock with Diverter .Make: Jaquar or Equivalent as directed by Engineer in Charge
83Providing and fixing Urinal with automatic flushing .Make: Jaquar or Equivalent as directed by Engineer in Charge
84Providing and fixing CP Towel Rail 600mm Long .Make: Jaquar or Equivalent as directed by Engineer in Charge
85Providing and fixing CP Towel Ring .Make: Jaquar or Equivalent as directed by Engineer in Charge
86Furniture and Utility
87Providing and installing of Cabin Table, MODEL: HT-528 1 89411 89411MIAN TABLE SIZE: 1800 X 750 X 780HT MM nos eachEXTENSION SIZE: 905 X 440 X 750HT MMSpecifications:Main Table top: 50mm thick Pre-laminate MDF board finished with 2mm PVC Edge Banding. Under Structure: Supported on MS Powder Coated Brackets and cross beams.16mm thick pre‐laminated MDF gable end or Main table desk is Supported on Side storage unit and other side 3 drawer Pdestal. Pedestal Configuaration and usign Laminate board and Thickes. Modesty panel :18mm Thick pre-laminated MDF Modesty panel of 450HT.Wire Management: 1 No. of 450mm Aluminium Flip Up and provision to mount swicthes and sockets on metal cable Dump and vertebra considered for wire uptake from floor to cable dump.Side Storage : (Openable Shutter and 3 drawers) The structure is made out of 16mm thick pre-laminated MDF boards. Make: Featherlite
88Providing and installing MODEL: FST TABLETable top: Made of 25mm thick prelaminated particle board of approved shade confirming to E1 norms. All the edges of workstation surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Modesty Panle: Made up of 18mm thick PLB modesty panel of 450 ht.Under Structure Support: Table top is supported on 25mm thick PLB Gable End.Wire Management: 65mm dia grommet hole for wire access.KEYBOARD TRAYMOBILE PEDESTAL: 400 X 450 X 600HT MM2 Drawers & 1 Filing CabinetMake: FeatherliteSize: 1200X600X750
89WORKSTATIONSMODEL: NEO-50Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade confirming to E1 norms. All the edges of workstation surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Main Return, Intermediate & End Partitions: Height - 1200mm frame with top and sides in Aluminium trims and junctions with diecast caps. Partition is made of 50mm thick 1200mm ht NEO based system with fabric above and lamiante below the table top. Fabric magnetic and glass markers are provided for each workstation.Under Structure: 18mm thick PLT gable end.Wire Management: Raceways are provided BTT only main spine and skirting on main (inside) spine for power and data cable management. 65mm dia grommet hole is provided for wire access.KEYBOARD TRAYMOBILE PEDESTAL: 400 X 450 X 600HT MM2 Drawers & 1 Filing CabinetMake: FeatherliteSize: 1350X600X750
90WORKSTATIONSMODEL: NEO-50Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade confirming to E1 norms. All the edges of workstation surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Main Return, Intermediate & End Partitions: Height - 1200mm frame with top and sides in Aluminium trims and junctions with diecast caps. Partition is made of 50mm thick 1200mm ht NEO based system with fabric above and lamiante below the table top. Fabric magnetic and glass markers are provided for each workstation.Under Structure: 18mm thick PLT gable end.Wire Management: Raceways are provided BTT only main spine and skirting on main (inside) spine for power and data cable management. 65mm dia grommet hole is provided for wire access.KEYBOARD TRAYMOBILE PEDESTAL: 400 X 450 X 600HT MM2 Drawers & 1 Filing CabinetMake: FeatherliteSize: 1350X600X750
91WORKSTATIONSMODEL: NEO-50Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade confirming to E1 norms. All the edges of workstation surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Main Return, Intermediate & End Partitions: Height - 1200mm frame with top and sides in Aluminium trims and junctions with diecast caps. Partition is made of 50mm thick 1200mm ht NEO based system with fabric above and lamiante below the table top. Fabric magnetic and glass markers are provided for each workstation.Under Structure: 18mm thick PLT gable end.Wire Management: Raceways are provided BTT only main spine and skirting on main (inside) spine for power and data cable management. 65mm dia grommet hole is provided for wire access.KEYBOARD TRAYMOBILE PEDESTAL: 400 X 450 X 600HT MM2 Drawers & 1 Filing CabinetMake: FeatherliteSize: 1200X600X750
92MODEL: FST 5 15200 76000SIZE: 900 X 600 X 750HT MM nos eachSpecifications: Table top: Made of 25mm thick prelaminated particle board of approved shade confirming to E1 norms. All the edges of workstation surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Modesty Panle: Made up of 18mm thick PLB modesty panel of 450 ht. Under Structure Support: Table top is supported on 25mm thick PLB Gable End.Wire Management: 65mm dia grommet hole for wire access.KEYBOARD TRAYCPU TROLLEYMake: Featherlite
93STORAGESMODEL: PLB STORAGE SIZE: 900 X 450 X 2100HT MMSpecifications:Top & Sides: 18mm Thk pre laminated particle boardBack: 9mm Thk pre laminated particle boardShutters: 18mm Thk pre laminated particle boardEdge: All exposed area with 2mm thick PVC edge lippingHandle: Finger groove handleMake: Featherlite
94MODEL: SENATOR HB Specifications: High Back Chair Leather Seat & Back Aluminium Fixed Arms Multilock Mechanism Aluminium BaseMake: Featherlite
95MODEL: FP INVENTION VA Specifications:Visitor ChairLeatherette Upholstered Cushioned Seat & Back Fixed Arms Chromeplated Sledge BaseMake: Featherlite
96MODEL: AMAZE MB Specifications:Medium Back Mesh Chair Self Calibrating Multilock MechanismAdjustable Lumbar Support Fabric Upholstered Cushioned SeatHeight Adjustable Arms Nylon BaseMake: Featherlite
97VISITOR CHAIRSMODEL: CONTACT VA Specifications: Mesh Back Visitors Chair Fixed ArmsPowdercoated Sledge Base Make: Featherlite
98Providing and installing Sony 189 cm (75 inches) BRAVIA 2 4K Ultra HD Smart LED Google TV, K-75S25M2, Black, Make:Sonybravia or Equivalent as directed by Engineer in Charge
99Providing and installing Sony 127 cm (50 inch) BRAVIA 2 II 4K Ultra HD Smart Google TV, K-50S25M2, Black Make:Sony or Equivalent as directed by Engineer in Charge
100Providing and installinghp Intel Core i3-12100T All in One PC hpR(HP 440 G9 AIO i3 12100T Win11P 1611 23.8\\") Make:HP or Equivalent as directed by Engineer in Charge
101Providing and installing (Laser/LED) Monochrome (Black) A4 and Legal Size Multifunction Printer (MFP) Make:HP or Equivalent as directed by Engineer in Charge
102Providing and installing Prestige PIC 3.1 V3 2000 Watts Induction Cooktop, Touch Panel,Anti-Magnetic Wall, Black Stove Make:Prestige or Equivalent as directed by Engineer in Charge
103Providing Bone China Elvis Plate Small White (Dia-12 in_White), Brand -Clay craft/ La opala or similar
104Providing Bone China Elvis Plate Small White (Dia-7 in_White), Brand -Clay craft/ La opala or similar
105Providing Bone china Single Portion and double portion Bowls set Brand -Clay craft/ La opala or similar as directed by Engineer in Charge
106Providing Bone china Serving Bowl & Servish Dish, Brand -Clay craft/ La opala or similar as directed by Engineer in Charge
107Providing fixing and Fixiing (AQUAGUARD ASPIRE DESIGNO UTC RO+UV 2X)Brand :Eureka Forbes or Equivalent as directed by engineer in charge.
108Fire ExtinguisherSupply, Installation and Commissioning of NBF SAFETY FIRST Portable Fire Extinguishers (V3) ISI Marked to IS 15683 Carbon dioxide 2 kg.
109Internal Electrical Works
110Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
111Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
112Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire
113Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required4 X 6 sq. mm + 2 X 6 sq. mm earth wire
114Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required4 X 10 sq. mm + 2 X 6 sq. mm earth wire
115Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections butexcluding modular plate etc. as required.5/6 A switch
116Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections butexcluding modular plate etc. as required.15/16 A switch
117Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections butexcluding modular plate etc. as required.3 pin 5/6 A socket outlet
118Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections butexcluding modular plate etc. as required6 pin 15/16 A socket outlet
119Supplying and fixing two module stepped type electronic fanregulator on the existing modular plate switch box includingconnections but excluding modular plate etc. as required.
120Supplying and fixing modular blanking plate on the existingmodular plate & switch box excluding modular plate asrequired.
121Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.
122Supplying and fixing brass batten/ angle holder including connection etc. as required.
123Supplying and fixing following size/ modules, GI box alongwithmodular base & cover plate for modular switches in recess etc.as required.1 or 2 Module (75mmX75mm)
124Supplying and fixing following size/ modules, GI box alongwithmodular base & cover plate for modular switches in recess etc.as required.3 Module (100mmX75mm)
125Supplying and fixing following size/ modules, GI box alongwithmodular base & cover plate for modular switches in recess etc.as required.4 Module (125mmX75mm)
126Supplying and fixing following size/ modules, GI box alongwithmodular base & cover plate for modular switches in recess etc.as required.6 Module (200mmX75mm)
127Supplying and fixing following size/ modules, GI box alongwithmodular base & cover plate for modular switches in recess etc.as required.12 Module (200mmX150mm)
128Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 way (4 + 12), Double door
129Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door
130Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole
131Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral
132Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required.2 run of cable
133Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required.3 run of cable
134Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness
135Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness
136Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase ACSupply, earthing etc. complete as required.
137Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door
138UPSSupplying, installation, testing and commissioning of online 3 phase UPS system with 30 minutes back up including batteries, interconnecting cables, battery racks etc.
139ADD ADDITIONAL 30MIN BACK UP KVA 3
140Supplying with fitting fixing of surface & wall mounted LED luminaries complete with all accessories including driver directly on wall / ceiling including connection with 1.5 sq mm P.V.C. insulated S.C.copper conductor as required and as directed by the department. (Crompton/PHILIPS/ BAJAJ/ Havells or equivalent considering the mother items rate and specification)18W 4ft LED Batten
141Supplying and commissioning of the following indoor recessed Type Round Luminairs complete with all accessories including driver in the false ceiling (Armstrong / Gypsum or similar type) mounted with necessary support and connection with 1.5sqmm PVC insulated SC copper conductor as required and as directed by the deptt. (Crompton or equivalent make)a)15w reccesed down light
142Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. (hevells /bajaj or equivelent make) 250 MM SWEEP NON-METTALIC
143AC/CCTV/ dataSupplying & installation of 3-Star Rated Inverter Hi-Wall split type air conditioning unit with Inverter Rottary Compressor, Cu Condenser Coil, Microprocessor based controller with Cordless Remote and R32/R410A . The scope of work will include initial gas charging , ODU , canvas connection , nitrogen flushing , pressure testing and electrical connection between lDU and ODU.as required and as directed by the department. ( Carrier /VOLTAS/diakin or equivalent considering the mother items rate and specification)a) 2.0 Ton Inverter Split AC
144Supplying & installation of 3-Star Rated Inverter Hi-Wall split type air conditioning unit with Inverter Rottary Compressor, Cu Condenser Coil, Microprocessor based controller with Cordless Remote and R32/R410A . The scope of work will include initial gas charging , ODU , canvas connection , nitrogen flushing , pressure testing and electrical connection between lDU and ODU.as required and as directed by the department. ( Carrier /VOLTAS/diakin or equivalent considering the mother items rate and specification)a) 1.5 Ton Inverter Split AC
145Providing Copper pipe including control cable fitting for Split /Cassetter AC as per required size inclduing Nitrile Insulation complete.For 1.5Tr to 2 Tr Capacity
146Supplying including fitting fixing of AC Starter of 20 A Motor Starter for AC machine in the existing 2/3 Module modular box with front plate as directed by the department.
147Supplying with fitting fixing of 2MP Bullet IP Camera for CCTV System as required and as directed by the department. ( cp plus/hik vision orv equivalent as approved by dept.)
148Supplying with fitting fixing of 2MP Dome IP Camera for CCTV System as required and as directed by the department. ( cp plus/hik vision orv equivalent as approved by dept.)
149Supplying with fitting fixing of 16 Channels NVR for CCTV System as required and as directed by the department. ( cp plus/hik vision orv equivalent as approved by dept.)
150Supplying with fitting fixing of 8-Ports Managed PoE Layer Network Switch in CCTV System as required and as directed by the department. ( Digisol/ D-link/ Netgear or equivalent as approved by dept.)
151Supplying with fitting fixing of 6U LAN RACK in LAN/cctv System as required and as directed by the department. ( D-link/VELRACK or equivalent as approved by dept.)
152Supplying with fitting fixing of 32\\" LED screen/TV for displaying in CCTV System as required and as directed by the department. ( lg/zebronics or equivalent as approved by dept.)
153Supplying with fitting fixing of 2TB DRIVE in CCTV System as required and as directed by the department. (DUGONG / WD or equivalent as approved by dept.)
154Supplying with fitting fixing of RJ 45 SOCKET with IO BOX for displaying in LAN System as required and as directed by the department. ( D-LINK/DIGISOL or equivalent as approved by dept.)
155Installation charge of Split type AC machine of 1.00 Ton to 2.00 Ton capacity
156External Electrical Works
157Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
158Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
159Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
160Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.
161Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 35 sq. mm and upto 95 sq. mm
162Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical indoordoor type floor mounting compartmentalize LT MAIN PANNEL BOARD of made of 16 SWG (1.66 mm) thick C.R. sheet and required size angle having 4 nos legs at the bottom complete neatly wiring done with provision for 160a 4P MCCB one no as incomer and out going as specified and directed by the deptt. confirming to IP 65 protection comprising of the following electrical items.1. 160a 4P MCCB one no as incomer,2. 100a 4P MCCB -1nos as outgoings 3. 63A 4P MCB- 4NOS
163Supply of following size PVC/XLPE insulated and PVC sheathed 1.1KV gd Solid Aluminum conductor up to 10 sqmm, balance stranded conductor, XLPE Insulated, cores laid up, PVC tape innersheathed, Armour (Aluminium wire for single core up to 70 sqmm, balance Aluminium strip, Glavanised wire for cables upto 2x10 sqmm,, 3x10 sqmm,,4x6 sqmm, & balance all galvanised steel strip), extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable as specified and directed by the deptt. ( Havells or equivelent make) 50.00Sqmm 3.5core Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58387264
AUTHORITY Government Departments
TENDER VALUE Ref. Documents
LAST DATE 25-11-2026
Authority
Authority Name Public Works Roads Department
Work Description Tender for Improvement Of Alternate Road To Maa Kamakhya Temple By Providing Reinforced Cement Concrete Bridge To Eliminate Hair Pin Bend, Rock Fall Protection & Improvement Of Junction At Entry Point Under Sopd-G For The Year 2023-24.(Construction Of Office Building For The Executive Engineer,Pwrd, Jalukbari Division, And 2 (Two) Nos. Of Offices For The Assistant Executive Engineers, Pwrd, Jalukbari Territorial Road Division At The 2Nd Floor Of Cdc, Jalukbari Office
Basic Detail
Tender No No.GRC/NIT/510/2021 -22/Pt.I/2263-69 Dtd.02.11.2026
Bidding Type Tender
Location
City Kamrup Metro
State Assam
Key Dates
Publish Date 05 Nov 2026
Submission Date 25 Nov 2026
Open Date 25 Nov 2026
Finance
Tender Value Ref. Documents
Tender Fee 7395
EMD 4.92 Lakhs
Exemption Available
Document List
1276748d-8741-481b-bcd7-c744880fe686.html
BOQ_85815.xls
FOB_SOPD_2026_27Pkg05.pdf
SBD_SOPD_2026_27pkg05.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 05, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 25, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 4 days
Nov 25, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 4 days

Tender Documents

Download All (ZIP) ↓
html

1276748d-8741-481b-bcd7-c744880fe686.html

xls

BOQ_85815.xls

pdf

FOB_SOPD_2026_27Pkg05.pdf

pdf

SBD_SOPD_2026_27pkg05.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender