Tender For Improvement Works To Skill Development Centre, Madhavaram Milk Colony, Chennai-51.
Tender Value
16.80 Lakhs
Estimated cost
Bid Submission
20 Nov 2026
14 days left
EMD
16800
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chennai → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Improvement Works To Skill Development Centre, Madhavaram Milk Colony, Chennai-51.
BOQ
| Sl. No. | Item Description |
| 1 | Civil Works |
| 2 | Earth work open excavation by manual means in all soils and sub-soils and to fulldepth as may be directed except in rock requiring blasting inclusive of shoring shuttering,bailing out water wherever necessary and depositing the excavated earth with a lead of10 mts. within the compound in places shown by the departmental officers and clearingand levelling the site, etc., complete complying with standard specification and as directedby the departmental officers. |
| 3 | Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard brokenstone jelly) using 40 mm gauge hard broken granite stone jelly for foundation includingdewatering wherever necessary and laid in layers of not more than 15 cm thick wellrammed, consolidated and including curing etc. complete complying with standardspecification and as directed by the departmental officers. For Foundation and Basement |
| 4 | Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specifications and as directed by the departmental officers.- For Foundation and Basement |
| 5 | Supplying and fixing in position of Mild Steel Angles / Mild Steel pipes and embedding it in plain cement concrete of 50cm depth for fixing chain link fencing including necessary cleat support applying red oxide primer etc., complete complying with standard specifications and as directed by the department officers. |
| 6 | Dismantling Brick Masonry in Cement mortar walls under 3m high complete complying with standard specifications and as directed by the department officers. |
| 7 | Dismantling Doors and Windows including removal of frames, hinges and fastenings complete complying with standard specifications and as directed by the departmental officers. |
| 8 | Stainless Steel (Salem Stainless Steel) Door Frame - Box Section using Stainless Steel Plate with following thickness with the size of 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel Hold fast etc including dismantling, making necessary chipping and holes in RCC columns, walls with power drills to the extent required ,including providing concrete 1:2:4 inside the box curing etc complete complying with standard specification and as directed by the departmental officers - SS Door Frame with thickness of 1.60mm. |
| 9 | Supplying and fixing Country wood fully panelled (Single Leaf) shutters using Country wood scantlings of size 100x40mm for styles & rails, 22mm thick planks for panels (5 Nos) and Brass / SS Furniture fittings (3 Nos - Brass / SS Hinges 125x30mm, 2 Nos - Brass / SS Tower bolt 300x12mm, 1 Nos - Brass/ SS Tower bolt 200x12mm, 1 Nos - Brass / SS Aldrop 250x16mm, 2 Nos - Brass / SS Handle 200mm) including cost of wind appliances and labour charges for fixing the furniture fittings in position etc., complete complying with standard specification and as directed by the departmental officers |
| 10 | Brick work In in Cement Mortar 1:5 (One cement and five sand) using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. Other type of bond shall be done as directed by the Executive Engineer in charge. |
| 11 | For Foundation and basement |
| 12 | For Superstructure in Ground floor |
| 13 | Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 14 | White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. |
| 15 | Supplying and fixing Mild Steel grills for grill work to gate and windows openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specifications and as directed by the departmental officers. |
| 16 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 17 | Supplying and fixing in position of 2''x2'' size chain link fencing 10 gauge Galvanised Iron Wire and fixing with M.S. Angle post using Binding Wire (Galvanised-18 G) including running the 2 ply and 4 pin G.I. barbed wire 12 gauge at bottom, middle and top of M.S. angle posts (As stiffener to the chain link fencing) etc, complete complying with standard specification. |
| 18 | Dismantling and clearing away carefully Flooring / glazed tiles etc complete complying with standard specification and as directed by the departmental officers. |
| 19 | Supplying and filling with filling stone dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 20 | Supplying and laying of Interlocking Paver Block Stone 63mm thick Over a base layer of crushed stone sandfilling including cost of materials laying and Labour charges etc complete complying with the standard specification and as directed by the departmental officers. |
| 21 | Supply and installation of two-track sliding uPVC windows with integrated fly mesh shall utilize uPVC profile sections with an outer wall thickness of 2.30mm (±0.2mm), featuring an outer frame of 92mm x 52mm x 52mm, a shutter of 66mm x42mm x 50mm, an interlock of 45mm x 36mm, a glazing bead of 24.5mm x 16mm, and a fly mesh shutter of 66mm x 30mm. All profiles of frames, sash, and mullion shall be reinforced, where required, with 1mm thick GI steel sections. Each window will be equipped with various security devices, such as touch locks or crescent locks, along with nylon rollers and an aluminium track forsmooth operation, all supplied as per requirements, compliant with relevant specifications, and as directed by departmental personnel. The windows shall incorporate 5mm thick Plain or Pinhead glass, held securely by TPE (Grey) weather-sealed gaskets. All corners and mullion joints of the frame and sash are to be mitred cut and fusion welded without any mechanical joints, with all welded joints neatly trimmed and finished with a grooved nib toensure the final products are free from sharp edges. The complete window units shall be fixed into prefinished openings by drilling and fastening through the outer frame using high-quality fasteners, and silicon sealant will be applied to fill the gap between the wall and window frame for a leak-proof installation and complete finish etc., Complete and as directed by the department officers. |
| 22 | Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 3.50 x 2.88m. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/ m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with necessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column, masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing etc... complete complying with standard specification and as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be got approved by Executive Engineer before use. |
| 23 | Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top. The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - Each., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete complying with standard specification and as directed by the departmental officers. All the Alu. Section are to be anodised with matt finish under electrically controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete. Aluminium sections, and furniture fittings shall be got approved by the Executive Engineer incharge. |
| 24 | Supply and fixing of auto ingress automatic double leaf Sliding Door system, Model : lS220b EMS 4.2 , Type-B without EM lock including following: automatic linear Sliding Door track with all electrical and mechanical components. Track length Approx. : 4200mm base profile and cover profile finish : Silver anodized 1 no. 3 position programme selector switch (auto/open/close) 1 no standard motion sensor concealed glass clamping with positive hold (anti-sagging feature 1 no integrated motion + safety sensor 2 Nos standard floor guide to suitable door 10/12mm glass thickness soft nose seal - 2 nos, brush profile - 2 nos, façade mounting bolt - 14 nos, installation and commissioning of automatic operator with 1 year onsite service warranty material transport 12mm clear toughened safety glass suitable for automatic sliding doors, manufactured from high-quality gold plus float glass and thermally toughened as per applicable bis standard . Glass shall have machine polished edges, with all required holes and cut outs completed before toughening. Approximate glass weight is 30kg/m2, with high strength and resistance to impact and thermal stress. Glass shall be supplied with suitable automatic sliding door fittings/carriers and safety sensors, designed according to the door panel size and total weight including consumables like (WCP Channel, big l-connector, CSK holes) installation handling and delivery charges. |
| 25 | Supplying and fixing the Wall Panelling with the following specification fixing horizontally and vertically in position of wall. Fixing the water proof ply wood 9mm thick board over the country wood planks. Over the ply wood OST sheet of 4mm thick will be fixed with necessary screws and adhesives giving neat finish. The top will be finished with two coats of sanding polishing. The surface will be finished with necessary design as directed by the Departmental Officers. The rate inclusive of all materials, labour power and conveyance of materials to the work site, loading & unloading etc., and as per drawing and design by the Departmental Officers. The water proof ply wood and OST sheet and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification. |
| 26 | GST at 18% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysNov 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender