Tender For Renovation Of Wrd Office Campus, Jhalawar
Tender Value
25.77 Lakhs
Estimated cost
Bid Submission
16 Nov 2026
5 days left
EMD
51557
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jhalawar → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Wrd Office Campus, Jhalawar
BOQ
| Sl. No. | Item Description |
| 1 | Item Description |
| 2 | P&F Marble Urinal Partition slab both sides polished of approved design cut from marble size 900x600mm. |
| 3 | Makrana `Adanga` or Raj Nagar 1St Quality White or Andhi Indo-Italian marble. |
| 4 | As per PWD BSR 2026 CH S-1 item 1.16.3 |
| 5 | P & F C.P. brass Urinal Flush Pipe set complete with flanged brackets of approved make. For 4 Urinals |
| 6 | As per PWD BSR 2026 CH S-1 item 1.28.1 |
| 7 | P & F C.P. brass Urinal Flush Pipe set complete with flanged brackets of approved make. For 3 Urinals |
| 8 | As per PWD BSR 2026 CH S-1 item 1.28.2 |
| 9 | P & F C.P. brass Urinal Spreader for stall urinal of approved make. |
| 10 | As per PWD BSR 2026 CH S-1 item 1.29.1 |
| 11 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :Gun-metal 15mm nominal bore. |
| 12 | As per PWD BSR 2026 CH S-2 item 15.1 |
| 13 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :Gun-metal 25mm nominal bore. |
| 14 | As per PWD BSR 2026 CH S-2 item 15.3 |
| 15 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 litres capacity. |
| 16 | As per PWD BSR 2026 CH S-2 item 26.3 |
| 17 | Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint |
| 18 | As per PWD BSR 2026 CH B-9 item 9.17 |
| 19 | Washing floor with soda, soap or other cleaning material. |
| 20 | As per PWD BSR 2026 item 13.16 CH.-B-13 |
| 21 | Demolishingstone rubblemasonry includingstackingof usablematerialanddisposalofunuseablematerialwithin50metersleadinclusive of de-watering wherever required. |
| 22 | As Per WR JHALAWAR zone BSR 2026 XVII Item no 5(b) |
| 23 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide |
| 24 | As per PWD BSR 2026 item no 9.8 CH.-B-9 |
| 25 | Plaster on new surface on wall in cement sand mortar 1:4 including racking of joints etc. complete fine finish :20mm thick |
| 26 | As per PWD BSR 2026 CH B-12 item 12.2.2 |
| 27 | Providing and Laying 80 mm thick cement concrete blocks of M-40 Grade (Manufactured with fully mechanised dry cast process with forced action mixer whose arms revolve along the main axis and rotate about its own axis also, having humidity sensor for moisture control of w/c ratio in concrete mix. Manufactured with steel moulds(Milled and manufactured in CSI diamond or CSI Nitro process for accuracy) on steel base plate of min 16 mm thick; Having Vibration and pressing action both together with the help of mutiplesynchronised vibrators. Power of hydraulic station should be minimum 50KW for compaction and cured in controlled chambers having humidity control and automated air circulation system) spreading 25mm thick sand underneath and filling joints with sand on existing W.B.M.base, as per IS15658:2006 and all materials shall conform to MoRTH Specification Clause 602. |
| 28 | PWD BSR 2026 CH B-17 ITEM NO 17.16 |
| 29 | Kerb Stones of 1200x300x150, 1000x450x150, 1000x600x150, 600x300x150 size (M-30) Providing and Laying cement concrete Kerb Stones of different sizes in M-30 grade (Manufactured with fully mechanised dry cast process with forced action mixer whose arms revolve along the main axis and rotate about its own axis also, having humidity sensor for moisture control of w/c ratio in concrete mix. Manufactured with steel moulds (Milled and manufactured in CSI diamond or CSI Nitro process for accuracy) on steel base plate of min 16 mm thick; Having Vibration and pressing action both together with the help of mutiplesynchronised vibrators. Power of hydraulic station should be minimum 50KW for compaction and cured in controlled chambers having humidity control and automated air circulation system) in position to the required line, level and curvature jointed with cement mortar 1:3 (1 Cement : 3 Coarse sand) including making of joints, drainage opening wherever required. |
| 30 | PWD BSR 2026 B-17 17.22 |
| 31 | Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (PugMill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400-12 & 400-13 and MoRTH Specification Clause 406.By Mechanical Means with all lead |
| 32 | PWD BSR 2026 R4 ITEM NO 4.6.1 |
| 33 | Laying and spreading available soil in the subgrade on a prepared surface,pulverising, mixing the spread soil in place with rotavator with 2percent slaked lime having minimum 70 percent of contents of CaO,grading with motor grader and compacting with the smooth wheel road roller at OMC to the desired density to form a layer of improved Sub-grade as per MoRTH Specification Cluase 402. (b) By Mechanical Means |
| 34 | PWD BSR 2026 CH R-4 ITEM NO 4.3 (A) |
| 35 | Construction of un-reinforced,plain cement concrete pavement M30 (Grade), ,thickness as per design, ,over a prepared subbase, ,with 43/53 grade cement as per Clause 602, ,coarse and fine aggregates conforming to IS:383, ,maximum size of coarse aggregate not exceeding 31.5 mm, ,mixed in a fully automatic Batching Plant and transported to site in transit mixer for having continuous agitated mixer, ,manufactured as per approved mix design including pumping of R.M.C. from transit mixer to site of laying, ,with all lead and lift including cost of admixtures in recommended portion as per IS 9103 to accelerate/retard setting of concrete, ,improve workability without impairing strength and durability as per direction of Engineer in charge, laid with a Fixed Form Paver (laying and fixing of 150 micron thick polythene Film and finished in continuous operation including provision of contraction and expansion, ,construction joints,applying debonding strips, ,primer,sealant near approaches to bridge/culvert andconstruction joints,admixtures as approved, ,curing of concrete slabs for 14-days using water, finishing to lines and grade as per drawing and MoRTH Specification Clause 602, including vacuum dewatering process with all required equipments (Dowel Bars will be paid separately). |
| 36 | PWD BSR 2026 CH R-6 ITEM NO 6.1 |
| 37 | Random rubble stone masonry (using R. R. stones where 75 % stones to be not less than 15 cm in size in any direction and weighing not less than 23 kg.) for foundation including curing with all leads of all construction materials including curing etc. complete(b).In cement sand mortar 1:4 |
| 38 | wrd bsr 2026 JHALAWAR zone VII 1.b |
| 39 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: |
| 40 | Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. |
| 41 | AS PER PWD BSR 2026 CH-12 ITEM 12.40.1 |
| 42 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. |
| 43 | 1: 3: 6 or richer mix |
| 44 | As per PWD BSR 2026 CH B-14 item 14.2.1 |
| 45 | Labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc. |
| 46 | As per PWD BSR 2026 CH b-13 item 13.24 |
| 47 | L/C for fixing of GI/AC sheet include. Cutting jhiri and repair , cutting of sheet , fixing of sheet with J or L hook and bitumen washer as per direction of EI 13.25 |
| 48 | As per PWD BSR 2026 CH b-13 item 13.25 |
| 49 | Mechanised cleaning of storage tanks comprises of following 6 stage as mentioned below :1. Mechanical dewatering2. Desalting removal of leftover dirty water and sludge with sludge pump3. Cleaning of wall, ceiling and floor by high pressure water jet with help of equipments which creates a pressure of 100-150 bar4. Removal of remaing sludge from floor with the help of industrial vacuum cleaner.5. Spraying of non toxic, bio degradable ecofriendly and bacterial agent certified by a govt approved laborary to disinfect the tank from all harmfull pathogens. The dose should be safe as per the UECD guidelines & 23 adopted on 17 th december 2001.6. Treatment of inside tank by exposing UV radiation to kill further suspended or floating bacteria if any (ABOVE 1000 LTR) |
| 50 | As per PWD BSR 2026 CH b-13 item 13.32 |
| 51 | Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead :With cement mortar 1 :4 ( 1 cement : 4 coarse sand). 12 mm thick |
| 52 | As per PWD BSR 2026 CH b-13 item 13.1 |
| 53 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : Size 450 mm x 300 mm |
| 54 | As per PWD BSR 2026 CH S-1 item 36.1 |
| 55 | Removing & Re fixing of P.V.C. Cistern fittings (Syphon, Ball cock & Handle Set) complete as per direction of Enginner-in-Charge |
| 56 | PWD BSR 2026 CH S-1 ITEM NO 67 |
| 57 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall). 25 mm nominal outer dia pipes |
| 58 | AS PER PWD BSR 2026 CH-S-2 ITEM 37.3 |
| 59 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia |
| 60 | As per PWD BSR 2026 CH S-3 item 16.3 |
| 61 | Providing & Laying C.C. 1:3:6 (Stone Agreegate 20mm nominal size) all around PVC Pipe including 7.5 cm thick bed concerte [Width & Height = Dia of Pipe in CM+15CM] excluding cost of Pipe & Excavation of trenches etc. PVC pipe 110 mm dia |
| 62 | As per PWD BSR 2026 CH S-3 item 16.5.1 |
| 63 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 110mm dia |
| 64 | As per PWD BSR 2026 CH S-3 item 17.1.II |
| 65 | Plain Tee. 110mm dia |
| 66 | As per PWD BSR 2026 CH S-3 item 17.3.II |
| 67 | Door Tee . 110MM DIA |
| 68 | As per PWD BSR 2026 CH S-3 item 17.4.II |
| 69 | Door Bend (Left & Right). 110 MM DIA |
| 70 | As per PWD BSR 2026 CH S-3 item 17.11.II |
| 71 | Vent Cowel .110mm dia |
| 72 | As per PWD BSR 2026 CH S-3 item 3.17.12.ii |
| 73 | Door Cap. 110mm dia |
| 74 | As per PWD BSR 2026 CH S-3 item 3.17.14.ii |
| 75 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete. New Plastered Surface (three or more coats) |
| 76 | As per PWD BSR 2026 item 12.22.1 CH.-B-12 |
| 77 | Providing and Laying in position of Cement concrete Nominal mix (1:1.5:3) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. Well graded crusher broken stone aggregate of maximum size upto 20 mm |
| 78 | wrd bsr 2026 JHALAWAR zone IX 6(d) |
| 79 | Supplying of M.S. reionforcement including labour charges for bending binding and placing in position all reinforcement as per drawing including cost of binding wire and all leads and lifts using. (ii) Tor or ribbed bars (IS :1786-1985) |
| 80 | wrd bsr 2026 JHALAWAR zone X 9(b)ii |
| 81 | Side shuttering including propping etc. complete (to achieve finish F 2 for :Retaining wall, counterfort, abutment, wing walls up stream or down- stream slope facings of dams and open faces of construction joints etc. |
| 82 | wrd bsr 2026 JHALAWAR zone X 1(c) |
| 83 | Excavation including loading, unloading, disposal and dressing ofexcavatedearthwithin initial leadof 50mand lift up to1.5mincludingdressingofexcavatedareaanddewateringwherever requiredcompletein |
| 84 | wrd bsr 2026 JHALAWAR zone V 1.b |
| 85 | Brick masonry(usingwellburntclaybricksofsize230 x110x70mm,classdesignation75asperspecification)uptoplinthincludingallleadsofallconstructionmaterialsincludingcuringetc. complete. |
| 86 | wrd bsr 2026 JHALAWAR zone VII 10.a |
| 87 | Plaster on new surface on wall in cement sand mortar 1:4 including racking of joints etc. complete fine finish :12mm thick |
| 88 | As per PWD BSR 2026 CH B-12 item 12.2.3 |
| 89 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 90 | As per PWD BSR 2026 CH B-3 item 3.1.4 |
| 91 | Providing & Fixing BLDC technology step regulator compatible ceiling fan, with aluminium body & aluminium blade, power factor not less then 0.9 , following service value (CMM/W) , with following air delivery , speed 350 RPM ( tolerance as per IS:374 2019 ) THD less then 10%, copper winding with class of Insulation 'F' complete with with secondary support safety cable ( steel rope), down rod up to 30 cm, cotter pin, shackle kit with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. |
| 92 | As per PWD BSR 2026 CH E-15 item 15.4.1 |
| 93 | Providing & Fixing of of BLDC Technology ventilating fans , single phase with PVC impeller, ABS body, Double Ball bearing, automatic back lower shutter including making connection, testing etc. as required. 150 mm sweep with Min. Air delivery 350 Cubic meter/Hr, 2000 RPM |
| 94 | As per PWD BSR 2026 CH E-15 item 15.5.1 |
| 95 | P & F of Wall cowl with Bird Screen Suitable for Outside Wall of Exhaust Fan Opening of following size and made out from 24 SWG GI sheet as per instructions of Engineer in charge including fixing with suitable fasteners etc. as required. |
| 96 | As per PWD BSR 2026 CH E-15 item 15.20.1 |
| 97 | Providing and fixing Square bars or other flat welded to window, ventilatiors etc. |
| 98 | As per PWD BSR 2026 CH B-9 item 9.27 |
| 99 | P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: |
| 100 | 20mm dia nominal bore. B class |
| 101 | As per PWD BSR 2026 CH s-2 item 2.1.2 b |
| 102 | Making connection of G.I. distribution branch with G.I. main including all fitting. Upto 25mm dia |
| 103 | As per PWD BSR 2026 CH s-2 item 2.3.1 |
| 104 | P & F Ball Cock (IS :1703 Mark) with Rod & P.V.C. Ball complete : |
| 105 | Brass wt.Not less than 400 gm, 20mm. |
| 106 | As per PWD BSR 2026 CH s-2 item 2.11.2 |
| 107 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. |
| 108 | Inside size 300 X 300 mm depth upto 0.5 M Cement cover with frame |
| 109 | As per PWD BSR 2026 CH s-3 item 3.21.1 |
| 110 | Bend 87.5 Dg. 110mm dia |
| 111 | As per PWD BSR 2026 CH s-3 item 3.17.9 |
| 112 | Pipe Clip. 110mm dia |
| 113 | As per PWD BSR 2026 CH s-3 item 3.17.15.ii |
| 114 | Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). |
| 115 | Polyester Powder coating aluminum ( minimum thickness of powder coating 50 micron) |
| 116 | Extra for shutters of sliding aluminum windows |
| 117 | As per PWD BSR 2026 CH B-16 item 16.1.2.3 |
| 118 | Providing and fixing aluminium U shape handle of size 100mm with SS screws etc. Complete as per direction of Engineer-in-charge. Polyester powder coated minimum thickness 50 micron aluminium . |
| 119 | As per PWD BSR 2026 CH B-16 item 16.9.3 |
| 120 | Filling the gap upto 5 mm depth and 5 mm width in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. |
| 121 | As per PWD BSR 2026 CH B-16 item 16.7 |
| 122 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed in aluminium doors ,windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. |
| 123 | Prelaminated particle board with decorative lamination on both sides. |
| 124 | As per PWD BSR 2026 CH B-16 item 16.4.2 |
| 125 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item.) |
| 126 | With glass panes of 4.0 mm thickness ( weight not less than 10.0 kg/sqm) as per IS : 2835. |
| 127 | As per PWD BSR 2026 CH B-16 item 16.5.1 |
| 128 | SITC of Single Stage, water cooled, High Speed (2880 RPM), Horizontal, Centrifugal, Openwell Submersible pumps set pre filled with coolent water and fitted with mechanical seal. The motor body of single phase pump shall be of SS and rest of all shall be of cast iron. Shaft of three phase pump shall be of SS 410 grade. All casting parts should be cathod electro deposition (CED) coated. Motor winding shall be 100% copper wire material. Dynamically balanced rotating parts to ensure min. vibration etc. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. |
| 129 | 1.0 HP, 1-Ø, (12 -27) Mtr, (200- 30) LPM |
| 130 | As per PWD BSR 2026 CH E-21 item 21.5.2 |
| 131 | P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: |
| 132 | 25mm dia nominal bore |
| 133 | 'B' Class |
| 134 | As per PWD BSR 2026 CH S-2 item 2.1.3 |
| 135 | P & F foot valve of superior quality and approved make with fittings : |
| 136 | Brass 25 mm. |
| 137 | As per PWD BSR 2026 CH S-2 item 2.23.1 |
| 138 | Providing and fixing expandable fastners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/R.C.C. and making good etc. complete |
| 139 | 25 mm long |
| 140 | 32 mm long |
| 141 | 40 mm long |
| 142 | 50 mm long |
| 143 | As per PWD BSR 2026 CH B-8 item 8.22.1 22.2 22.3 22.4 |
| 144 | S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required on surface including heavy duty saddles with base at spacing of 0.60 mtr. etc as required. |
| 145 | 25 mm |
| 146 | 50 mm |
| 147 | As per PWD BSR 2026 CH E-1 item 1.12.2 1.12.5 |
| 148 | Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. |
| 149 | As per PWD BSR 2026 CH B-9 item 9.26 |
| 150 | Anti termite treatment of floor using Imidacloprid 30.5% EC non repellent, odorless, low dose, environmentally safe terniticide with rapid action non corrosive stain free, by drilling 12mm diameter holes 300mm apart injecting the emulsion as per specification and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area DPE 12mm dia termitube system with required number of junction boxes are to be installed. The termitube will run all along the perimeter wall both inside and outside. In the middle area the termitube to be installed at an interval of 1.00 Mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. After successful testing of termitube, pesticide emulsion of imidacloprid 30.5% EC mixed with water in the ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. The plinth area of the area treated will be measured for payment. |
| 151 | As per PWD BSR 2026 CH B-1 item 1.39 |
| 152 | P & F European type white glazed vitreous china 1st quality Double syphonic W.C (IS :2556 Mark) with P or S trap including cutting and making good the wall and floor |
| 153 | As per PWD BSR 2026 CH S-1 item 1.4 |
| 154 | Providing and fixing fully panelled /partly panelled double leaf shutters frame for windows and ventilators as per approved design and drawings with approved steel fittings as per Annexure ‘A’ and width of styles, bottom and top rails 75mm including intermediate rails 50mm wide, beading of 25mm x 15mm size on both faces : |
| 155 | As per PWD BSR 2026 CHB-8 item 8.5.1.3 |
| 156 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 157 | Short point (up to 3 mtr.) |
| 158 | Medium point (up to 6 mtr.) |
| 159 | Long point (up to 10 mtr.) |
| 160 | PWD Electrical BSR 2025 CH E1 item no 1.1.1, 1.1.2, 1.1.3 |
| 161 | Supplying and laying FR PVC insulated & unsheathed flexible copper conductor of following nominal sizes with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. |
| 162 | 1 x 1.5 sq.mm |
| 163 | As per Electrical BSR 2025 CH-E4 item no 4.1.1 |
| 164 | SITC of IP 20 box made out from 1.0 mm thick CRCA sheet steel with depth of minimun 30 mm and finished with powder coating and suitable for mounting LED tube including side covers, holders , internal wiring to illuminate the single sided connection LED tube. ( Without tube). As per PWD Electrical BSR 2025 CH E17 item no 17.11.1 |
| 165 | Suitable for 2' LED Tube shape fixture for single rod |
| 166 | PWD Electrical BSR 2025 CH E-17 item no 17.11.1 |
| 167 | Extra for Mirror polishing on terrazzo/Kota stone work where ever required to give high gloss finish complete. |
| 168 | As per PWD BSR 2026 CH B-11 item 11.25 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender