Tender For Special Repairs To Booster Pump House - Ii And Ug Sump At Af Station Chimney Hills
Tender Value
38.47 Lakhs
Estimated cost
Bid Submission
25 Nov 2026
6 days left
EMD
77000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bengaluru Urban → Karnataka
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Booster Pump House - Ii And Ug Sump At Af Station Chimney Hills
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick work or stone walls etc incl raking out joints hacking for key scrubbng down with water complete all as specified and directed. |
| 2 | Taking down chowkats or frames with shutters ( without taking of shutter from the frame) not exceeding 1.5 sqm each complete all as specified and directed. |
| 3 | Taking down chowkats or frames with shutters ( without taking of shutter from the frame) exceeding 1.5 sqm but not exceeding 4.00 sqm each complete all as specified and directed. |
| 4 | Material & Labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth without using extra cement in internal surfaces complete all as specified and directed. |
| 5 | Material & Labour for rendering 10 mm thick on ceiling as in chajja in CM 1:3 even and smooth without using extra cement complete all as specified and directed. |
| 6 | Material & Labour for preparing new plaster surface apply two coat of oil bound distemper over a coat of wall care putty to obtained smoothness of wall surfaces over one coat of primer complete all as specified and directed. |
| 7 | Material & Labour for preparing new plaster surface apply two coat of oil bound distemper over a coat of wall care putty to obtained smoothness of ceiling surfaces over one coat of primer complete all as specified and directed. |
| 8 | Material & Labour for preparation and washing, rubbing down and stopping of distempered and painted surfaces of wall including cornices and applying two coats of acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete as per manufacturer's specification complete all as specified and directed. |
| 9 | Material & Labour for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) of 25mm thick as in correction/levelling course, finished surfces even and rough to receive floor finish complete all as specified and directed. |
| 10 | Material & Labour for Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl over screed bed or bedding layer of mortar 15mm thick for laying tiles in cement mortar 1:6 complete all as specified and directed. |
| 11 | Material & Labour for Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in skirting over 10mm thick rendering as in backing coat of CM 1:4 complete all as specified and directed. |
| 12 | Material and labour for 75mm thick PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in paving/plinth protection, finish the surface even and fair without using extra cement complete all as specified and directed |
| 13 | S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 140mm long complete complete all as specified and directed. |
| 14 | Supply & Fixing for Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 15 | Supply & Fixing for Powder coated aluminium frames and shutters/grills for door and window, ventilator or framing with one or more rebates joining cleat for fixing etc of any thpe, side hung shutter, sliding shutters etc complete all as specified and directed by Engr-in-Charge. |
| 16 | Material & Labour for Rubber gasket EPDM/Neoprene for fixing glass pane in aluminium frame work/door/window complete all as specified and directed |
| 17 | Supply & Fixing for Sheet glass 4mm thick, ordinary quality and glazing with oil putty in square of any size in each pane all as directed |
| 18 | Supply & Fixing for Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples |
| 19 | Material & Labour for PCC 1:2:4 type B0 using 12.5mm graded stone aggregate of 25mm thick as inpadding course, finishsurface even & rough for roof treatment all as specified and as directed. |
| 20 | Material & Labour for 10 mm thick rendering in cement mortar 1:3 , on ceiling surfaces and finishing the surface with even and smooth without using extra cement all as specified and as directed. |
| 21 | Applying Oil bound Bitumen primer @ 0.20 Kg/Sqm all as specified and directed |
| 22 | Material & Labour for APP minimum 4mm thick polymeric membrane minimum weight not less than 4kg/sqm and reinforced with polyster nonwoven fabric matt(wt. not less than 150 gms/sqm) & applying a coat of blown hot Bitumen over the membrane @ 12.0 kg/sqm complete all as specified and directed |
| 23 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in di mension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made all as specifie and directed by Engr-in-Charge. |
| 24 | Demolition reinforced cement concrete in any description and in any position complete and thrown at low lying area all as specified and as directed |
| 25 | Excavation over areas n exc 1.5m in depth , getting out in hard dense soil complete all as specified and as directed |
| 26 | Excavation over areas exc 1.5m & n.exc 3.00 depth , getting out in hard dense soil complete all as specified and as directed |
| 27 | Material & Labour for Cement concrete 1:4 :8 type D2 using (40 mm graded aggregate) as in filling, fdn, mass concrete and sub base of floors etc. |
| 28 | Material & Labour for RCC M-30 (20mm graded aggregate) design mix in foundations including rafts, footings, foundation beams, plinth beams, copings , bases for columns etc basement slabs, under reamed piles and mass concrete complete all as specified and directed. |
| 29 | Material & Labour for RCC M-30 (20mm graded aggregate) design mix in Walls, retaining walls, basement walls, ballast walls and the like, any thickness above top of footings complete all as specified and directed. |
| 30 | Material & Labour for RCC M-30 Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 31 | Material & Labour for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia for securing with clips quality conforming to deformed or twisted bars complete all as specified and directed.. |
| 32 | Material & Labour for mild steel TMT bars 6 to 8 mm spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia for securing with clips quality conforming to deformed or twisted bars complete all as specified and directed. |
| 33 | Material & Labour for form work for fair finished surfaces to side of concrete foundations, footings, bases of coloumns,raft and raft beams, sides and soffits (If any) of foundation and plinth beams and similar work all as specified and as directed |
| 34 | Material & Labour for form work for fair finished surfaces to walls, retaining walls, abutments, parapets and staircase railings and similar work complete all as specified and directed. |
| 35 | Material & Labour for form work for rough finished surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick(Horizontal or sloping) complete all as specified and directed. |
| 36 | Material & Labour for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide fair finished complete all as specified and directed . |
| 37 | Material & Labour for 12mm thick rendering in CM 1:3 on brick or concrete surfaces finished even and smooth complete all as specified and as directed. |
| 38 | Supply only Liquid water proofing compound all as directed. |
| 39 | Material & Labour for applying the first coat of Dr. Fixit Roofseal Classic New or equivalent in other brands at a rate of 2 sq. m./ltr./coat and then applying a second coat at 90° to the first coat at the rate of 2 sq. m./ltr./coat. over a coat of self priming Dr.fixit Roofseal classic new or equivalent in other brands (diluted with water in the ratio of 2:1 at the rate of 1 lit /10 sqm) including preparation of surface by removing loose particles/dust as per manufacturer instructions on dry surface of source complete all as specified and as directed |
| 40 | S&F Cast iron soil sand cast pipe, waste and vent pipes 100mm in any length with or without ears, with cement joints, laid in wall/trenches or in floors or walls complete all as specified and directed. |
| 41 | Material & Labour for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment as in Base plate/Gusset plate, cleats for securing purlins/rafters and smilar articless conforming to Fe 290 (Gde E 165) all as directed |
| 42 | Material & Labour for Framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, frame balusters walkways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165 all as specified and directed |
| 43 | Material & Labour for preparation steel surfaces with two coats of Synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. |
| 44 | Material & Labour for precast cement concrete block masonry exc. 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:4) all complete all as specified and directed. |
| 45 | Returning, filling in including spreading leveling watering and well ramming in layers not exc 25 cm (soil) complete all as specified and directed. |
| 46 | Removing excavated materials not exc 50 Metre and deposition where directed at a level not exc 1.5 M above the starting point (soil) complete all as specified and directed. |
| 47 | Dismantling posts or struts (wood, steel or R.C.C.) any section embedded in concrete brick work, masonary etc, including taking out embedded portion and making good disturbed ground complete all as specified and directed. |
| 48 | Dismantling old fencing , any type complete all as specified and directed. |
| 49 | Demolition of stone boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 50 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out hard soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed. |
| 51 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed. |
| 52 | Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed. |
| 53 | Material & Labour for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 54 | Material & Labour for walling of random rubble masonry un coursed well bonded and solidly hearted built in CM 1:4 complete all as specified and directed. |
| 55 | Material & Labour for walling of random rubble masonry un coursed well bonded and solidly hearted built in CM 1:4 (except stones) complete all as specified and directed. |
| 56 | Supply & Fixing for 110 mm dia PVC (SWR) pipes single socketed fixed in walls and floors or trenches etc. as in weep holes of retaining wall complete all as specified and directed. |
| 57 | Material & Labour for hand packing broken stone or boulders (any thickness) at back of walls over arches and raising (or lowering) to the required level complete all as specified and directed. |
| 58 | Extra for hammer dressing to face stone and dressing of face, beds, joints for a maximum depression of 40mm from the straight edde held against the dressed faces of Random rubble walling, uncoursed brought upto courses complete all as specified and all as directed. |
| 59 | Material & Labour for walling of random rubble masonry un coursed well bonded and solidly hearted built in CM 1:4 cement mortar 1:3 raised pointing to randam or polygonal rubble uncoursed or brought upto courses complete all as specified and directed. |
| 60 | Supply & Fixing in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured). |
| 61 | Demolition of unreinforced cement concrete in ground floor and paving n.exc 15cm thick (below or above ground level) etc complete all as specified and directed. |
| 62 | Material & Labour for PCC 75mm thick, 1:4:8 type D-2 40mm stone aggregate as in sub base of flooring complete all as specified and directed. |
| 63 | Material & Labour hard core of broken bricks gauge n. exc 63 mm, deposited spreaded and leveled in layer not exc 15 cm thick, watered and rammed to atrue surface, broken stone or boulder complete all as specified and directed. |
| 64 | Material & Labour for Prepolished Chequered cement concrete tiles of size 30cm X30cm X 25mm thick, set and jointed and pointed in neat cement slurry in floors with grey cement and pigments over 15 mm thich screed bed in CM 1:6 complete all as specified and directed. |
| 65 | Material & Labour for provinding 100mm thick cement concrete in 1:2:4 type B1, (using 20mm graded stone aggregate) finishing cement concrete surface even and fair without using extra cement as in plinth, Path/hardstanding complete all as directed. |
| 66 | Material & Labour for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed. |
| 67 | Material & Labour for Sand cushioning for laying interlocking tiles complete all as specified and directed. |
| 68 | Material & Labour for Plain cement concrete 1:3:6 type C-1(using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 69 | Supply , laying, jointing and leakage testing GI Pipe 50 mm bore medium grade (ISI marked) including all fittings such as bend, tee, elbow, union, reducer etc, laid in trenches / floor/ walls etc complete all as specified and directed.Notes: (i) The laying and jointing of pipes are required to be carried out in short / long streches catering to specific requirements of a particular quarter, building block or a group of blocks.(ii) Excavation & earth work shall be measured & paid seperately under respective item of BOQ. |
| 70 | Excavation in trenches not exc 1.5 m wide and not exc 1.5 min depth for laying of UG Pipe/ UG cable and getting out in hard dense soil all as specified and directed. Note- Exacavation shall be done by Manual process. |
| 71 | Returning, filling, including spreading, levelling, watering and well ramming in layers not exc 25cm thick in any type of exacavated soil all as specified and directed. |
| 72 | Removing excavated material to a distance not exc 50 m and deposited where as directed at a level not exc 1.5 m above the starting point all as specified and directed. |
| 73 | Supply and fix Foot valve heavy duty 50 mm size of Brass body with screwed/flanged ends as required at site |
| 74 | Supply & Fixing for 50 mm bore non return valve (ISI Marked) class PN-1.6 , IS-5312 both end flanged suitable forCI/MS pipe including all fittings washer, nuts & bolt etc complete all as specified and directed. |
| 75 | Supply & Fixing for Gun metal Gate valve (ISI Marked) with iron wheel head, screwed both ends for iron pipe of the size 50 mm bore complete all as specified and directed. |
| 76 | Supply, laying & testing of M.S ERW black pipes of 50 mm bore of class 'B' (as per IS 3589 & 1239) for wet riser system. The pipes shall be laid in trenches or fixed on walls in any position or to be use in common headers of suction/delivery line of pump with necessary specials, such as bends, Reducers, orifice plates, if any tees, flanges, tapers etc at any required lenght complete all as specified and as directed. The rates shall include the cost of consumables for cutting and welding, painting with a coat of red oxide over two coats of colour/approved colour |
| 77 | Material & Labour for Drilling and Tapping GI/CI water mains (in position) for branch connection of 50mm including all fittings such as bend,elbows,tees,reducers and unions etc all as directed by engineer in charge. |
| 78 | Material & Labour for cutting road / hard standing to depth not exceeding 60 CM and to width not exceeding 45 CM for laying GI Pipes and making good the disturbed surfaces by 1:3:6 type C1 using 20 mm graded stone aggregate complete all as specified and as directed by Engineer-in-Charge. |
| 79 | Material & Labour for Construction of valve chamber of size 900mm x 900mm x 600mm internal size including necessary earth work excavation, PCC 1:4:8 type D2 for foundation, brick work in cement mortar 1:4, PCC 1:2:4 type B1 for coping, 15mm thick rendering in cement mortar 1:4 including provision of mild steel cover 3mm thick on 40 x 40 x6 mm angle iron frame work with 2 coats of synthetic enamel paint over a coat of zinc chrome primer and locking arrangements complete all as specified and as shown on drawings. |
| 80 | Taking down 50 mm dia GI pipe, including dismantling, removal from existing position, lowering and stacking serviceable material as directed, complete all as specified and directed |
| 81 | Taking down carefully aluminium/copper point wiring light, fan, sockets or power complete from surface wiring or from concealed wiring without disturbing concealed conduit including fittings such as ceiling rose, light fittings of any type, fan regulators etc and making good to the disturbed surfaces wall ceiling floors to match existing surfaces complete all as specified and directed. |
| 82 | Supply & Fixing for Point wiring complete with 1.5 Sqmm single core multi stranded copper conductor FRLS PVC insulated unsheathed 1100 V grade cable including 1.5 Sqrnm copper conductor multi stranded PVC insulated unsheathed cable for earth continuity conductor in and including PVC casing and capping/conduit with all accessories and l.2mm thick PVC bóx with 3 mm uniform thick laminated ISI marked sheet cover for mounting of switches sockets regulators etc complete for one light point, controlled by one switch /5 amps one way one fan point controlled by one switch and regulator / one socket outlet point three pin 5 amps complete all as specified and directed.. |
| 83 | Supply & Fix in repair switch piano 6 Amps one way flush type complete all as specified and directed. |
| 84 | Supply & Fix in repair Switch socket combination , 2 in 1, 5 pin 6 Amps flush type with Box All complete all as specified and directed. |
| 85 | Supply & Fix in repair fan regulator AC 230 V electronic socket type complete all as specified and directed. |
| 86 | Supply & Fix in repair ceiling rose ,ISI Marked complete all as specified and directed. |
| 87 | Supply & Fix Retrofit LED Tube 1x 20 W of lumens 100 /Watt ,4 feet,220V, 6500 K,Both side Connection complete all as specified and directed. |
| 88 | Supply & Fix MCB SP 6 to 32 Amps10 KA 240V 50HZ, ISI Marked complete all as specified and directed.. |
| 89 | Supply & Fix MCB SPN 6 to 32 Amps10 KA 240V 50HZ, ISI Marked complete all as specified and directed.. |
| 90 | Material & Labour in replacement submain wiring /Circuit wiring with PVC insulated, 1100 volts grade unsheathed copper conductor cable in and including PVC Conduit/Casing capping with accessories fixed on wall /ceiling with GI screws complete with 2X2.5 sqmm+1 X2.5 Sqmm for earth continuity conductor all as directed. |
| 91 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor and suitable lugs of size 50 sq mm 3.5 core all as per directed by engr in charge . |
| 92 | Material & Labour for submersible cable, PVC insulated and sheathed, 3 core, 16 Sqmm, multistranded copper conductor, 1100 volt grade, heavy duty with suitable lugs complete all as specified and directed. |
| 93 | Material & Labour for all burnt old size bricks, sub class B brick laid dry flat with width equal to length of whole brick, as cable protection complete all as specified and directed. |
| 94 | Supply and filling fine sand to the full width of trench for cushioning of cable for cable protection including spreading and punning down complete all as specified and directed |
| 95 | Supply & Fixing for MK1 Dol-10 HP DOL starter incl suitable relays, connection with existing pump set and testing in presence of Engr-in-Charge . |
| 96 | Material & Labour for fixing MCCB 4 Pole, 415 V, Adjustable type, 63 Amps with breaking capacity 25 kA ,at existing LT panel and making good connection with nut bolts and washers and wire connections etc. to be fixed in the existing TR panel complete all as specified and directed. |
| 97 | Supply, installation, testing and commissioning of 415V, 3 Phase, 4 Wire LT Distribution Panel fabricated from 1.6 mm thick CRCA sheet steel, powder coated, wall/floor mounted, IP54 protection, comprising: following specifications are as under:- * 01 Nos. 63A TPN MCCB as Incomer * 02 Nos. 32A TPN MCCB as Outgoing Feeders* Aluminium busbar of suitable rating (minimum 100A)* RYB phase indication lamps* Digital Ampere meter and Voltmeter with selector switch (optional)* Neutral link and Aluminium earth bar* Removable gland plate for cable entry* Complete internal wiring, interconnections, hardware and accessories* Testing and commissioning completeRecommended Panel Size:* Plinth mounted: 500 mm (H) × 400 mm (W) × 200 mm (D)* CRCA sheet steel, powder-coated finish, IP54.Including required PCC work |
| 98 | Taking down existing 50 sq.mm LT power cable from its existing position, including disconnection, removal from cable trench/supports, dismantling of clamps/cleats and accessories wherever required, coiling and stacking the cable at site as directed |
AI Tender Summary
Tender Timeline
Nov 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysDec 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender