Tender For Provn Of Grease Traps And Connected E&M And B&R Works At Certain Locations At 503 Su Under Ge (Af) Gurgaon
Tender Value
43.66 Lakhs
Estimated cost
Bid Submission
25 Nov 2026
21 days left
EMD
88000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gurgaon → Haryana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Grease Traps And Connected E&M And B&R Works At Certain Locations At 503 Su Under Ge (Af) Gurgaon
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc completed all as specified. |
| 2 | M & L for rendering 15 mm thick on other than fair faces of brick wall finished fair & even in CM 1:6 complete all as specified and directed. |
| 3 | M & L for rendering 15 mm thick on fair faces of brick wall with mixing WPC @ 3% by wt of cement finished fair & even in CM 1:4 complete all as specified and directed. |
| 4 | M & L for rendering 10 mm thick on brick or concrete surface of ceiling finished fair & even in CM 1:3 complete all as specified and directed. |
| 5 | M&L Preparing of new surface of wall and applying two coats of exterior emulsion paint over a coat primer on walls complete all as specified and directed by Engineer-in-charge. complete all as specified and as directed by Engineer-in-Charge . |
| 6 | M & L preparation of newly plastered surfaces of wall and applying two coats of OBD over a coat of putty filling including preparation of surfaces on walls as specified and directed . |
| 7 | M & L preparation of newly plastered surfaces of ceiling and applying two coats of OBD over a coat of putty filling including preparation of surfaces on walls as specified and directed . |
| 8 | M&L for preparation(complete removal of existing treatment) of old decorated external wall/ceiling surface of existing treatment by scrapping with Trucare Wall Sander : L-01/H-01 (having mechanical vaccum mechanism) having RPM not less than 1500, sand pad of 80 grit having dia of 7\\"/9\\" to make the surface free from dust, loose paint etc or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and applying Two coats of wheather proofing exterior acrylic emulsion paint over priming coat premium quality on wall/ceiling surface including applying 2mm thick wall care putty over disturbed surface during preparation of any reason, sand papering thus make surface smooth upto 4th storey buildings complete all as specified and directed. Note : (a) Stage for Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes.(b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator. |
| 9 | M&L for preparation of plastered or unplastered old decorated surfaces by complete removal of existing treatment by mechanised sander of berger paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling of holes and cracks with with suitable material like cement or plaster of paris etc and thereafter applying two coat of oil bound distemper over a coat of1- 2 mm putty on walls. Note : (a) Stage for Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes.(b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator. |
| 10 | All as per item No.9 here-in-before but on surfaces of ceiling. |
| 11 | Material and labour for preparation of old painted surfaces of steel of any description and girth, not otherwise described and treated with one coat of synthetic enamel paint complete all as directed.Make of Paint : Asian(Apcolite)/ Nerolac (Goodlass)/ Berger paints/ICI Dulux |
| 12 | Preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-In-Charge. |
| 13 | Taking down chowkats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each all as specified and directed by Engineer - in – Charge. |
| 14 | Taking down chowkhats or frames with shutters without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each and all as specified and directed by Engineer - in - Charge. |
| 15 | S&F factory made uPVC white colour casement (Open-able) door with pleated mesh made of extruded profile with wall thickness of 2.0mm (+/- 0.2mm). door profile with hollow section with multi chamber, frame (60mmx58mm) T profile (One vertical length in between two shutters) (60mmx71mm) Glazing bead corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware EPDM gasket + -0.2 mm thick galvanized steel frame (28mmx21.5mm) 'T' profile (27mmx17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [ three track window/ door handle made of zinc alloyed (while powder coated) Corner strikers: cylinder, Door transmission gear made of mild steel with multi point locking system with strikes, 3D hinges of zinc alloyed (white powder coated)] and 6mm thick toughened glazing with selected quality glass. Note : Selected quality clear/frosted Glass and mesh cost of all other connected accessories deemed included in unit rate. Net opening will be measured for payment purpose. |
| 16 | S&F power coated aluminium frame work for doors, windows,partition s etc incl grill for windows for windows etc with one or more rebated section incl jointing cleats for fixing etc complete complete. |
| 17 | S&F powder coated anodised aluminium Window shutters, partition wall, aluminium section weighting 0.55 Kg/Rm incl necessary joining cleats glazing clips rubber neoprene packing, handles two Nos in each door, hinges anodised aluminium snap beading screws etc complete all as specified and as directed. |
| 18 | S&F powder coated anodised aluminium door shutters, partition wall, aluminium section weighting 0.55 Kg/Rm incl necessary joining cleats glazing clips rubber neoprene packing, handles two Nos in each door, hinges anodised aluminium snap beading screws etc complete all as specified and as directed. |
| 19 | S&F for 4.8/5.0 mm thick sheet glass ordinary quality and glazing each pane n exc 0.50 Sqm fixed with neoprene rubber gasket in aluminium frame work complete all as specified. |
| 20 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to steel frames with tinned tacks, or galvanized wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed. |
| 21 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. |
| 22 | Pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc and applying a shop coat of red oxide primer including providing PCC 1:3 :6 type C-0 using 12.5 mm graded crush stone aggregate for filling back of chowkhats complete all as specified and as directed by the Engineer-in-Charge |
| 23 | Pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc and applying a shop coat of red oxide primer including providing PCC 1:3 :6 type C-0 using 12.5 mm graded crush stone aggregate for filling back of chowkhats complete all as specified and as directed by the Engineer-in-Charge |
| 24 | S & F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats all as specified and directed by Engineer - in - Charge |
| 25 | S & F for flush shutters with both sides Matt finish laminate incl leeping on the edges, solid core construction , with block board core and plywood face panels , commercial type on both sides , thickness 30 mm , etc complete all as spd and directed |
| 26 | S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm long all as specified and directed by Engineer - in – Charge . |
| 27 | S&F 300mm Aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 28 | S & F aluminium handle cast type anodised, 125 mm long all as specified and directed by Engineer - in - Charge . |
| 29 | S & F Stainless Steel butt hinges, medium weight 100mm size all as specified and directed by Engineer - in - Charge . |
| 30 | Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded Wood Grain PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and Wood Grain PVC sheets for top rail, lock rail and bottom rail on either side and a gap insert for top rail and bottom rail; paneling of Wood Grain PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site all as specified in SSR part-II 2004 Section-8, clause 8B.1 to 8B.2.1 and shown on drawing in page No 146 of SSR part-II 2004. |
| 31 | Factory made PVC solid single door frame (chowkats) of size 50 mm x 47 mm made out of 5 mm Wood grain PVC sheet reinforced with MS square tube, supplying and fixing in opening all as specified in SSR part-II 2004 Section-8, clause 8B.3 to 8B.3.2 and shown on drawing in page No 150 of SSR part-II 2004. |
| 32 | Taking down of old /unserviceable kitchen cabinet / Cupboard incl all fixture and fittings. For measurement superficial area in elevation will be measure complete all as specified and as directed. |
| 33 | S&F 18 mm thick 100 % solid WPC (Wood polymer composit) plain board( minimum density 650 kg/cum ) of one side prelam/ rigidlam and the other side balancing laminate colour to make the kitchen cabinet shutter/ drawer front shutter . Complete all as specified and directed .Note:- Material testing certificate (MTC) and authentication of the product shall be mandatory to the manufacturing company |
| 34 | Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the permises complete all as specified and as directed |
| 35 | M&L Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick Screed bed or bedding layer of mortar for laying floor finishes in CM 1:6 |
| 36 | M & L for light shade , Virified Ceramic tiles 8-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20 mm thick Screed bed or bedding layer of mortar for laying floor finishes in CM 1:6 etc completed all as specified. |
| 37 | M & L for light shade , Virified Ceramic tiles 8-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. on vertical surface set and over including 10 mm thick rendering with cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified. |
| 38 | M & L first quality coloured glazed ceramic, joint free tiles fixed in pattern of different colour including border of size 300x450x7 mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid on and including 10 mm thick rendering in cement mortar (1:3), including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed. Note :- Pattern of the tiles will be decided by GE at the time of execution. |
| 39 | Taking down steel tubing/ PVC 15mm bore and connections including cleaning for refixing or removing to stores complete all as specified and directed by Engineer - in – Charge. |
| 40 | All as per Srl Item No 50 here in before but 20mm bore all as specified and directed by Engineer - in - Charge. |
| 41 | Supplying and laying of CPVC pipes 20 mm outer diameter SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 42 | Supplying and laying of CPVC pipes 25 mm outer diameter SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 43 | S&F 20mm dia Brass TEE for CPVC pipe |
| 44 | S&F 20mm dia Brass elbow for CPVC pipe |
| 45 | S&F 25mm dia Tank Adaptor |
| 46 | S&F 25mm dia union |
| 47 | S&F 25mm dia Ball Valve |
| 48 | Cutting chases, pinning in brick walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc; and cuttings chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth all as specified and directed by Engineer-in - Charge. |
| 49 | S & F in repairs 600 x 450 mm size beveled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed with wooden plugs with chromium plated brass screws and cup washers all as specified and directed by Engineer - in - Charge . |
| 50 | S & F in repairs stainless steel sinks with drainage board made out of 1.00 mm thick sheet for kitchen with plugs, washers, waste pipes, including bedding in cement mortar to dwarf wall or including fixing cast iron cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm with bowl size 410mm x 330mm x 160mm, with and including PVC waste pipe and CP waste coupling 32 mm dia and making good to disturbed surfaces, fixed in repairs, complete all as specified. |
| 51 | Dismantling water tanks of capacity exceeding 500 and not exceeding 1000 ltrs all as specified and directed by Engineer - in - Charge. |
| 52 | S & F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 1000 Litres all as specified and directed by Engineer - in - Charge . |
| 53 | M&L ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball with minimum weight 210 gm screwed for 20mm bore dia iron pipe supplied and fixed in repairs complete all as specified and as directed by Engineer-in-charge. |
| 54 | S&F in repair vitreous china coloured One piece EWCs with integrated cistern, seat cover , jet spray and twin flush fittings and including P or S trap etc. all as spfd and completed ( Cat part CARVEL of Cera or Equivalent ) |
| 55 | S&F in repair vitreous china pedestal pattern wash hand basin (flat back) white of size 550x400mm including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector, including cutting for and pinning in ends of brackets complete all as specified. |
| 56 | S & F in repairs PVC connection 15mm size with PTMT nuts of length 450mm all as specified and directed by Engineer - in – Charge. |
| 57 | S & F in repairs bib taps, long body,fancy type cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified. |
| 58 | S & F in repairs angle cock/stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe or for brass ferrule complete all as specified. |
| 59 | S&F in repairs Fancy type single leaver wall mixer with provision of hand shower, but without hand shower cat No DRC-37119 make Jaquar or equivalent out of makes spd in list of makes of any colour, 15mm chromium plated screwed down for iron pipes or brass ferrule complete all as specified and as directed. |
| 60 | S&F in repairs fancy type CP pillar tap single leaver basin mixer without popup waste system with 450 mm long braided hoses cat No DRC-37011B make Jaquar or equivalent out of makes spd in list of makes of any colour for basin 15 mm dia screwed down high pressure with long screwed shank sand fly nuts screwed for iron pipe fixed as in repairs complete all as specified and as directed. |
| 61 | S & F in repairs chromium plated shower rose 125mm size incl shower arm casted 3000 mm long flat shape for wall mounted showers with flange incl fixing to steel pipe or union all as specified and directed by Engineer - in - Charge. |
| 62 | S&F in repair health faucet with double lock 1 meter brass plated stainless steel flexible hose and wall hook complete all as specified and directed |
| 63 | S & F in repair CP paper holder of Make-AKP-35751P of Jaquar or equvelent in kohler. complete all as specified and directed. |
| 64 | S&F in repair Kitchen plate rack of stainless steel of silver colour ,1 mm thick of size 900mmx1200 mmx 250mm including fixing with screws complete all as spcified and as directed. |
| 65 | S & F soap dish brass chromium plated, fixed to plugs with brass chromium plated screws complete all as specified and directed by Engineer - in - Charge. |
| 66 | S & F Brass chromium plated, tubular towel rails 20 mm dia, D- type, 60 cm long between flanges, completed all as specified and directed. |
| 67 | S&F in repairs 19 mm dia Aluminium curtain rod with powder coated along with ornamental attachment at both ends and one set of ornamental decorative MS clamps to fixed to walls complete all as specified and directed. |
| 68 | Demolition of stone slabs and tiles of any description or thickness in floors/walls, aprons etc laid bedded and pointed in any mortar. |
| 69 | M&L for Z-Black granite stone slab of sizes as directed (of any type) 20 mm thick on cooking platform,shelves etc machine cut,bedded over 20 mm thick in CM1:4 and jointed with grey cement slurry and pointed with white cement with admitures of pigment to match with shade of granite stone incl grinding and polishing compelte all as specified. |
| 70 | Dismantling/removing old damaged worn out APP of any thickness incl screed bed or plastering of any thickness and removing the rubish materials outside MOD land at a dumping place earmarked marked by any state govt/municipalities etc any distance complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 71 | Dismantling/removing old damaged worn out APP of any thickness incl screed bed or plastering of any thickness and removing the rubish materials outside MOD land at a dumping place earmarked marked by any state govt/municipalities etc any distance complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 04, 2026
11:30 IST
Tender Published
Tender notice published.
TodayNov 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysNov 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender