Tender For Repair To Floor Tile, Toilet/Bathroom, Joinery And Other Misc Repairs In Offrs Md Accn Under Age B/R-Ii At Mil Stn Yol
Tender Value
38 Lakhs
Estimated cost
Bid Submission
28 Nov 2026
14 days left
EMD
76000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Floor Tile, Toilet/Bathroom, Joinery And Other Misc Repairs In Offrs Md Accn Under Age B/R-Ii At Mil Stn Yol
BOQ
| Sl. No. | Item Description |
| 1 | Taking down Chowkats or Frame (without taking off shutter from the frame) exc. 1.50 sqm but n exc 4.00 Sqm each complete all as specified and as directed. |
| 2 | Taking down Chowkats or Frame (without taking off shutter from the frame) n exc. 1.50 sqm complete all as specified and as directed. |
| 3 | Taking down shutters of any description but exc. 1 Sqm and n exc. 2 Sqm each complete all as specified and as directed. |
| 4 | Taking down shutters of any description n.exc 1 Sqm each complete all as specified and as directed. |
| 5 | Dismantling fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section, framed or unframed work complete all as specified and directed. |
| 6 | M&L plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads exc 13 & n exc 25 sq. cm.2nd class hardwood. |
| 7 | Dismantling boarding, any description fixed in any position with nails complete all as specified and directed. |
| 8 | S & F MDF board 18/19 mm thickness , exterior grade prelaminated both side with decorative choice lamination and other side balancing white lamination andfixed with screws to timber frame work as in wall panelling cup boards shutters (sliding or fixed) in repairs complete all as speicified and directed. |
| 9 | S&F Pressed steel frames for doors of size 125mmx60mmx1.25mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed complete all as specified and directed. |
| 10 | M & L for PCC 1:2:4 type B0 with using 12.50mm graded crushed stone aggregate as in bed block, bed plates etc for embeding hold fasts etc complete all as specified and directed. |
| 11 | S&F 35 mm thick 2nd class hard wood glazed and skelton shutter open nrebated and prepared to receive glass gauze etc (without shas bar) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of numbers of shutter as specified in SSR Pt I Section 8, clause 8.2 (a) complete all as specified and as directed. |
| 12 | S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 13 | S/F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed. |
| 14 | S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and as directed. |
| 15 | Powder coated anodized aluminium door chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- a) Shutter vertical member 85.00 x 44.45 x 1.80mm weighing 1.302 Kg/RM.b) Shutter top member 83.5 x 44.45 x 1.70 mm weighing 1.243 Kg/RM.c) Shutter bottom member 114.30 x 44.45 x 1.29mm weighing 1.139 Kg/RM.d) Shutter lock rail 83.5x44.45x1.70mm weighing 1.243 Kg/RM.e) Anodised aluminium handle, fancy type, 350mm long and aluminium tower bolt of size 150mm.(f) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (g) Aluminium anodised frame of door of section 101.6 x 44.45 x 1.75mm weighing 1.367 Kg/M, with flat iron hold fasts and necessary concrete in PCC M-15, type B-I using 12.5 mm graded crushed stone aggregate to fix hold fasts all as directed.Note:- Shutter shall be fixed with ISI marked brass mortice lock with duplicate keys. |
| 16 | Powder coat three track sliding anodized aluminium window with chowkhat of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member, size varying from 40 x 20.0 x 1.00mm (weighing 0.313 Kg/RM) to 50.80 x 25.40 x 1.09 mm (weighing 0.489 Kg/RM).(b) Shutter top & bottom member, size varying from 40 x 20.0 x 1.00mm (weighing 0.313 Kg/RM) to 50.80 x 25.40 x 1.09 mm (weighing 0.489 Kg/RM).(c) Powder coated anodized aluminium frame of chowkhat (including track of suitable size) of section varying from 83.5 x 44.45 x 1.80 mm (weighing 1.302 Kg/RM) to 104 x 44.45 x 1.80 mm (weighing 1.60 Kg/RM), with flat iron hold fasts and necessary concrete to fix hold fasts all as directed.(d) 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets complete. (e) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos). |
| 17 | S&F Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including 10 mm thick square bar in grill and following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window.(ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf.(iii) MS tower bolt 150mm long - 2 No per leaf(iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf.(v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf.(vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf.(vii) Flat iron fillets of size 20X3 mm for fixing wire gauge.(viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day. |
| 18 | S & F Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed in repair with stainless steel wire staples or wooden beads complete all as specified and as directed. |
| 19 | S & F Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads complete all as specified and as directed. |
| 20 | Hacking old broken glass (any thickness, size, quality or description) from wooden Frames/steel frame glazed with wooden beads complete all as specified and as directed. |
| 21 | S & F for sheet glass, 4.0mm thick glazing with beads or oil putty with glazing clips, not exc. 0.50 sqm in each pane, complete all as specified and as directed. |
| 22 | S & F for Figured glass, pin head type, 4.0mm thick glazing with beads or oil putty with glazing clips, not exc. 0.50 sqm in each pane, complete all as specified and as directed. |
| 23 | S & F 150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed. |
| 24 | S & F 150 mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 25 | S & F 100 mm long stainless steel butt hinges medium weight, cold rolled and fixed complete all as specified and as directed. |
| 26 | S & F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 27 | S & F 100 mm long aluminium anodised barrel tower bolt complete all as specified and as directed. |
| 28 | S & F 100 mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 29 | S & F 75 mm long stainless steel butt hinges medium weight, and fixed complete all as specified and as directed. |
| 30 | M & L appying two coats synthetic enamel paint over a coat of pink primer on wooden surface any description over 10 cm in width or girth not otherwise described including preparation complete all as specified and as directed. |
| 31 | Preparation of new steel and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 32 | Dismantling of plain or corrugated steel sheeting of any gauge ,thickness as in roof covering complete all as specified and as directed. |
| 33 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed |
| 34 | Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 35 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 36 | S & F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc to Fe 290 Gde-E-165. complete all as specified and directed. |
| 37 | Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; flat iron for framing grills, framework of water tanks and similar work conforming to Fe.290. Gde-E-165, all as specified. |
| 38 | 4 mm thick non asbestos fibre cement building boards of size 600x600mm (E board)as in ceiling fixed or laid/ inserted to timber/ GI/ aluminium frame work fixed with nails, all as specified. Aluminium anodised snap grid frame work of size of size 605 mm X 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/ instructions), cutting holes for electrical fittings fixed on and including aluminium tee of size 25mmX25mmX1.50 mm as main runner, aluminium tee of size 25mmX25mmX1.25 mm as cross runner and aluminium angle of size 25mmX25mmX1.25mm at the perimeter suspended from soffit at approx 900 mm centre to centre with hangers 6 mm dia galvanised (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanised iron flat 40 mm X 3 mm size, 60 mm long and expansion hold fasteners 12.5 mm dia, 40 mm long including necessary scaffolding all as specified and directed including Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified. |
| 39 | Demolition of brick/stone work built in cement mortar including all quoins, arches, pillar including coping etc., complete all as specified and directed. |
| 40 | M&L brick work with fly ash old size bricks, straight or curved on plan exc 6m redius, in cement mortar 1:6 complete all as specified and directed. |
| 41 | Dismantling water tanks n. exc. 500 ltr capacity and removing from site complete all as specified and directed.. |
| 42 | Dismantling water tanks exc. 500 ltr & nexc 1000 ltrs capacity and removing from site complete all as specified and directed.. |
| 43 | M & L for rotational moulded polyethene water storage tanks 500 litrs capacity (cylindrical vertical with threaded closed top) hoisted and fixed in position all as specified in SSR part-I complete all as specified & directed |
| 44 | M & L for rotational moulded polyethene water storage tanks 1000 litrs capacity (cylindrical vertical with threaded closed top) hoisted and fixed in position all as specified in SSR part-I complete all as specified & directed |
| 45 | Demolition of cement concrete (unreinforced) of of any descriptions, in ground floors (Floor Topping, Sub Base etc) not exc 150mm thick, above or below ground level complete all as specified and directed. |
| 46 | M & L 25 mm thick PCC 1:2:4 type B0, using 12.5 mm graded stone aggregate as in floor finished for fixing of tiles complete all as specified and directed. |
| 47 | M&L for 75mm thick cement concrete 1:3:6, type C2 using 20mm graded stone aggregate as in plinth protection and similar works finished even and smooth without using extra cement complete all as specified and directed. |
| 48 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 49 | M&L Granite (of any type) tiles 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes CM 1:6 complete all as specified and directed |
| 50 | M & L Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) light shade, polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding layer of cement mortar in CM 1:6 complete all as specified and directed |
| 51 | M&L for Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in over and including 10mm thick rendering of cement mortar in CM 1:4 neat cement slurry and pointed in white or coloured cement to match. |
| 52 | M & L Non-skid ceramic tiles 7 to 8 mm m thick(square or rectangular) coloured joint free , area of each tiles exc 0.18 sqm but not exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding layer of cement mortar in CM 1:6 complete all as specified and directed |
| 53 | M&L for Non skid ceramic tiles 7 to 8 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in over and including 10mm thick rendering of cement mortar in CM 1:4 neat cement slurry and pointed in white or coloured cement to match. |
| 54 | M & L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) coloured, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match,laid over and including 15mm thick cement screed /rendering in CM 1:6 complete all as specified and as directed. |
| 55 | M & L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm/450x300mm thick set and jointed in neat cement slurry and pointed in white or colour cement tomatch as in Skirting, Dados, etc., laid over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed. |
| 56 | Taking down cement plaster of any description on brick/stone walls, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, remove dust, debries/rubbish etc complete all as specified and as directed. |
| 57 | M & L for rendering 15mm thick in cement mortar 1:6 on other than fair face of brick work or concrete surfaces, finished even and smooth with using using extra cement complete all as specified and as directed. |
| 58 | M & L rendering 15mm thick in cement mortar 1:4 on external fair faces of brick work or concrete surfaces plastered surfaces finished even and smooth without using extra cement with water proofing compound as per manufacture instruction complete all as specified and directed.Note: WPC shall be measured and paid separately as supply only. |
| 59 | M & L 5mm thick rendering in cement mortar 1:3 on ceiling surfaces, finished surface even and smooth, without using extra cement complete all as specified and as directed. |
| 60 | Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of 2 mm thick wall care putty including preparation of surface complete, all as specified and as directed by Engr-in-Charge. |
| 61 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint with mechanical roller having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete, all as specified and as directed by Engr-in-Charge |
| 62 | M & L for preparing new surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed. |
| 63 | Supply only liquid water proof compound complete all as specified and directed.. |
| 64 | M & L for preparing new surfaces of walls and applying three coats of white wash, complete all as specified and as directed. |
| 65 | M & L for PCC 1:2:4 type B-0 with using 12.5mm graded crushed stone aggregate as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounde or chamfered angles and throating, including use of form work,complete all as specified and directed. |
| 66 | S & F in repair Vitreous china wash down water closet pan (Pedestal pattern), white fixed in repair with plastic water closet seat, black,closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device including PVC valveless,syphonic action type, flushing cistern 10 ltrs capacity, low level,white, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32mm dia for low level cistern complete all as specified and as directed. |
| 67 | S & F in repair Vitreous china squatting pan, Orissa pattern, size 580x440mm white, with integral foot rests including provision of cement concrete bedding and PVC valveless, syphonic action type, flushing cistern 10 ltrs capacity, low level, white, with inlet, ball valv, float and handle including brackets with fixing of flushpipe of polyethyne of low or high density or PVC 32mm dia, for low level cistern complete all as specified and as directed. |
| 68 | S&F in repairs Wash hand basins, Vitreous China (oval type, coloured) size 435 mm x 505 mm x 180 mm, excluding tap etc including cast iron brackets duly painted including cutting and pinning in ends and making good disturbed surfaces in cement mortar (1:3) as well as matching with existing with 32 mm bore waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, PVC connections 15mm size with CP brass coupling nuts of length 450mm, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, chain and plug, PVC 32mm dia flush pipe and all accessories fixed in repairs complete as all specified. Make: Cat Part No. KUS-WHT-35601 of Jaquar or equivalent makes mentioned in Appx 'C' |
| 69 | S & F in repair Vitreous china wash basin size 550x400mm with Pedestal (flat back or angle back type) including 32mm dia waste fittings, brass chromium plated for glazed ware sinks,basins, etc. with long screwed shanks and flynuts, flange end bedded in red lead cement and other end fixed with provision of 15mm bore dia pillar mixer fancy type chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. |
| 70 | M &L HDPE waste pipe of 32mm dia fixed wash basin, sinks etc complete all as specified |
| 71 | Taking down or up steel 15mm bore water tubing and connections including cleaning for re fixing or removal to store complete all as specified and as directed. |
| 72 | Taking down or up steel 20mm bore water tubing and connections including cleaning for re fixing or removal to store complete all as specified and as directed. |
| 73 | M & L 15mm dia bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified & directed |
| 74 | M & L 20mm dia bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed. |
| 75 | S&F CP over head shower rose 150 mm x 150 mm, square shape, single flow with rubit cleaning system, complete all as specified. Make: Cat Part No. OHS-CHR- 35495 of Jaquar or equivalent makes mentioned in Appx 'C' in repair. |
| 76 | S&F in repairs Stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) , screwed down ,high pressure, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified. (Cat Part No CON-083KN/ CON-089KN of 'Jaquar' or equivalent in makes mentioned in Appendix 'C') in repair |
| 77 | S&F in repairs Stop valves/ angle valve, cast copper alloy, chromium plated, fancy type with wall flange, screwed down, high pressure, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified. (Cat Part No CON-053KN/ CON-059KN of 'Jaquar' or equivalent in makes mentioned in Appendix 'C'). |
| 78 | S&F in repiars Bib taps with wall flange, 15mm bore, cast copper alloy, chromium plated, fancy type, screwed down high pressure, screwed for iron pipe or for brass ferrule fixed in repairs, all as specified. (Cat Part No OPL-15037/ VGP-81037 of 'Jaquar' or equivalent in makes mentioned in Appendix 'C'). |
| 79 | S&F in repair basin CP Mixer for 15mm bore, cast copper alloy, fancy type, single lever basin mixer without pop up waste system with 450 mm long braided hoses and base flange for iron pipe, or brass ferrule, all as specified.(Cat Part No KUB-350511FB of 'Jaquar' or equivalent in makes mentioned in Appendix 'C'). |
| 80 | S&F in repair 15mm bore CP wall mixer with telephonic hand shower for mixing hot or cold water, screwed for iron pipe complete, all as specified. (Cat Part No FUS-29267 of 'Jaquar' or equivalent in makes mentioned in Appendix 'C'). |
| 81 | S&F in repair Toilet paper holder of stainless steeel fixed to walls chromium plated (CP) brass screws complete, all as specified and as directed by Engr-in-Charge. |
| 82 | S&F in repairs Brass Chromium Plated, tubular towel rail, 19mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed in repair, complete all as specified and directed. |
| 83 | S&F in repairs Soap dish, chromium plated, fixed to plugs with chromium plated, brass screws, fixed in repairs all as specified. Make: Cat Part No. ACN-1131N of Jaquar or equivalent makes mentioned in Appx 'C'. |
| 84 | S&F in repairs Waste coupling (half or full threaded) (Minimumu weight 32mm-45 gms) complete, all as specified and as directed by Engr-in-Charge |
| 85 | S&F in repairs PVC connections 15mm size with nuts of length 600mm complete, all as specified and as directed by Engr-in-Charge |
| 86 | S&F in repairs Glass shelf assembly consisiting of 5.5mm thick sheet glass shelf 12 cm wide with Stainless steel bracket guard & railing, 60 cms long, fixed with chromium plated brass screws, complete all as specified. Make: Cat Part No. ACN-1173N of Jaquar or equivalent makes mentioned in Appx 'C' |
| 87 | S&F in repairs Corner Glass shelf assembly consisiting of 5.5mm thick sheet glass shelf 30cm wide with Stainless steel bracket guard & railing, 40 cms long, fixed with chromium plated brass screws, complete all as specified. Make: Cat Part No. ACN-1173N of Jaquar or equivalent makes mentioned in Appx 'C' |
| 88 | S&F in repairs PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, in repairs, all as specified. Make: Cat Part No. 2602 of Cera or equivalent in makes mentioned in Appx 'C'. |
| 89 | S&F in repair Metal finish, fancy type, curtain rod, 25 mm dia including inticated brackets, globes, cleats, fixed to walls all as specified. |
| 90 | S & F in repair Looking mirror of size 600 x 450 , 6mm thick with bedding and 6mm thick commercial ply board complete all as specified & directed |
| 91 | S & F in repair Looking mirror of any size, 6mm thick with bevelled edge fixed with Stainless steel Screws as required complete all as specified & directed |
| 92 | S&F CP Towel Rail, 600 mm long without lower hangers, fixed in repairs all as specified. Make: Cat Part No. CAN-1181FHN of Jaquar or equivalent makes mentioned in Appx 'C' |
| 93 | S & F 20mm dia ball brass valve high pressure with polythene float and fly nut complete scrwed for iron pipe or brass ferrule and fixed complete all as specified and directed. |
| 94 | S & F 20mm dia ball brass valve high pressure with polythene float and fly nut complete scrwed for iron pipe or brass ferrule and fixed in repairs complete all as specified and directed.. |
| 95 | S & F in repairs stop valves 20mm bore cast copper alloy, screwed down high pressure, screwdd both ends for iron pipe or for unions and fixed including cutting, threading to existing 20 mm GI pipe line and providing 01 No. 20 mm GI union complete all as specified and as directed. (Note : To be fixed in existing inlet of service tanks at 1.80 metre hight from GL) |
| 96 | M & L for PVC (SWR) 110mm bore (dia) soil, waste and ventilating pipe, type 'B' ,singe socketed, in any length with Rubber Ring Joints fixed to walls with MS/PVC Clamps including taking down unserviceable pipe, fittings, etc, complete all as specified and directed.. |
| 97 | M & L for PVC (SWR) 110mm bore (dia) soil, waste and ventilating pipe , type 'B', singe socketed, in any length with Rubber Ring Joints fixed to foor , including taking down unserviceable pipe, fittings, etc, complete all as specified and directed.. |
| 98 | M & L for PVC (SWR) 75mm bore (dia) soil, waste and ventilating pipe , type 'B', singe socketed, in any length with Rubber Ring Joints fixed to walls with MS/PVC Clamps, including taking down unserviceable pipe, fittings, etc, complete all as specified and directed. |
| 99 | M & L for PVC (SWR) 75mm bore (dia) soil, waste and ventilating pipe , type 'B', singe socketed, in any length with Rubber Ring Joints fixed to floor, including taking down unserviceable pipe, fittings, etc, complete all as specified and directed. |
| 100 | M & L for PVC (SWR) 110mm bore (dia), Bends any type, with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed. |
| 101 | M & L for PVC (SWR) 75mm bore (dia), Bends any type, and Jointing with Solvent Cement, complete all as specified and as directed. |
| 102 | M & L for PVC (SWR) 110mm bore (dia), Single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed. |
| 103 | M & L for PVC (SWR) 75mm bore (dia), Single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed. |
| 104 | S & F for PVC (SWR) floor trap 75mm with gratings including Jointing to waste pipe with solvent cement complete all as specified and directed. . |
| 105 | S & F 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor complete all as specified and directed. |
| 106 | S & F sinks with drainage board made of stainless steel 1 mm thick kithcen or laboratory with plugs, washers and wastes, including bedding in cment mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 m bowl size 410 mm x 330 mm x 160 mm fixed in repair complete all as specified and directed. |
| 107 | S&F sinks without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm fixed in repair complete all as specified and directed. |
| 108 | S&F 40mm dia cupboard knobs fixed with nut, screw and washer of mild steel bright finished complete all as specified and directed. |
| 109 | Aluminium handles, cast type, anodised 75mm size complete all as specified and directed. |
| 110 | S&F 125mm Ditto, hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 111 | S & F Continuous (piano) hinges 30 mm flaps width,mild steel, bright finish or electrogalvanised fixed with screws complete all as specified and as directed complete all as specified and directed. |
| 112 | S & F mortice lock brass, 4 levers, vertical type, Size 100mm complete all as specified and directed. |
| 113 | S & F 5.5mm thick Sheet glass,ordinary quality and fixed with rubber packing and aluminium snap beading in aluminium doors in square exc 0.5 sq. m in each pane complete all as specified and directed. |
| 114 | S & F door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg. fixed in repair complete all as specified and directed. |
| 115 | S&F telescopic channel , 1mm thick, fixed to wooden sliding shutter of cup boards , kitchen racks/drawers etc with suitable size cadium screws complete complete all as specified and directed. |
| 116 | S & F magnet catcher with magnet for cupboards all as specified and directed |
| 117 | S & F in Steel Plate Rack made of stainless steel 1mm Thick size 900x900 x 250 mm deep, fixed in position with plugs, washers and steel screws complete, all as specified |
| 118 | S&F health faucet (ABS body with 1 metre long easy flex in chrome finish tube and wall hook complete with accessories, fixed in repairs complete all as specified and directed. Make Jaquar, Cera or Equivalent |
| 119 | S&F in PVC Cabinet with mirror of size 350x450mm,fixed to wall with screw all as speicifed and as directed. Make:-Prayag Cat No. 551 or equivalent. |
| 120 | S&F in repair jet spray stainless steel complete all as specified and directed. make Cera of equivalent. |
| 121 | S&F 20mm dia stainless steel curtain rails with fixing and brackets, stops , rollers and fixed to walls complete all as specified and as directed. |
| 122 | Taking down aluminium door shutter n. exc. 2 sqm each, taking out servicable glass panes, hydraulic door clocer, butt hinges, double action hydraulically regulated floor spring and other fittings, if required carefully and refixing in the same opening after repairs of unservicable or loosened joints/cleats of top rail/bottom rails/ lock rails and styles etc and fixing old servacable glass, any thickness with rubber packing and aluminium beadings, fixing of old servicable hydraulic door closer, double action door spring duly oiling/greasing and fixing all servicable fittings complete all as directed by Engr-in-charge. NOTE:- Unservicable door closer, double action floor spring, glass panes and other fittings etc shall be replaced and paid under separate items of schedule. |
| 123 | S&F Transulant Fibre Sheet 2mm thick Fibre glass reinforced translucent corrugated / plain sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall and fixed in any position upto 8mtr height in Chajjas etc including taking down of old Fibre Glass sheet any thickness complete all as specified and directed. . |
| 124 | S&F in repair of Modular Kitchen complete all as specified below and as directed by Engr-in-Charge :-Kitchen Cabinet Bottom Unit * :- Providing and fixing of machine crafted box type cabinet bottom unit 560mm depth using 19mm water proof HDHMR board with 0.6mm laminate both side. The shutters will also be machine crafted with the same water proof HDHMR board, with 0.6mm both side laminate while on the out side it will be 0.8mm laminate or 1mm laminate of glossy finish and a machined edge band of 2mm. The hinges will be auto loaded hinges of approved make , which is of IS marked. The shelf is to be adjustable with two slots provided at 300mm spacing so as to accommodate the shelf. The plywood should be of thickness 19mm water proof HDHMR board with 0.6mm laminate on top and bottom with machine cut edge band 0.5mm thick. |
| 125 | Kitchen Over head wall Unit* :- Providing and fixing of machine crafted box type over head unit 325mmmm depth using 19mm water proof HDHMR board with 0.6mm laminate the both side. The shutters will also be machine crafted with the same water proof HDHMR board, with 0.6mm laminate both side it will be 0.8mm laminate or 1mm laminate of glossy finish and a machined edge band of 2mm. The hinges will be auto loaded hinges of approved make , which is of IS marked. The shelf is to be adjustable with two slots provided at 300mm spacing so as to accommodate the shelf. The plywood should be of thickness 19mm water proof water proof HDHMR board with 0.6mm laminate on top and bottom with machine cut edge band 0.5mm thick. |
| 126 | Kitchen Accessories with soft closures :- (a) Cutlet basket 430mmx510mmx100mm(b) Cup & Soucer 430mmx510mmx100mm(c) Plate (Thali) 430mmx510mmx150mm(d) Plain 430mmx510mmx150mm(e) Plain 430mmx510mmx200mm(f) Degergent holder 430mmx510mmx200mm(g) Oil pullout 160mmx510mmx585mm(h) Telescopic drawer channels(j) Dustbin hoder |
| 127 | Full Height Storage and Loft Unit :- Providing and fixing of machine crafted frame work using 19mm water proof HDHMR board with 0.6mm laminate both side. The shutters will also be machine crafted with the same water proof HDHMR board, with 0.6mm both side laminate while on the out side it will be post form laminate or 1mm laminate and a machined edge band of 2mm. The hinges will be auto loaded hinges of approved make , which is of IS marked. The same is to be fixed in the location as directed.Note:- All measurement are to be maesured as Length x Height .However, the depth of the boxes are to be as per the specifications described above. |
| 128 | S & F 15mm bore brass CP sink mixer for mixing hot & cold water screwed down for iron pipe and fixed in repaircomplete all as specified and directed. Make : Jaquar, CERA, Hindware |
| 129 | S&F Door Seal 40mm wide Bottom Carbon Metal Seal Strip, Door Air Gap Rubber Shield, Dust Proof, Water Proof with 3 Nos self tapping carbon Screws all as directed by Engr-in-Charge |
| 130 | S&F Grating doom 100mm dia of PTMT without waste hole (Minimum weight 25gms) fixed in repair complete all as specified and directed. |
| 131 | S&F Grating doom 125mm dia of PTMT with waste hole (Minimum weight 25gms) fixed in repair complete all as specified and directed. |
| 132 | S&F Bottle trap 32 mm bore dia of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/ 40mm-270 gms) fixed in repair complete all as specified and directed. |
| 133 | S&F Helical Spring fixed by welding or tapping Screws in any type of chowkat Steel / wooden fixed in repair complete all as specified and directed. |
| 134 | S& F in repair one piece floor mounted toilet water closet of size (WxPxH) 360 x 675x750 mm white or tinted S trap 300 mm trendy square design slim UF ezee close seat cover wash down system dual flush (6/32 ltrs) mechaniism with necesary fixing bolts /screws etc complete all as specified. Make Jaquar / CERA Cat Part No.(S1013164) or Equivalent |
| 135 | Demolition of reinforcement cement concrete as in any position or any description n.exc 15 cm thick (below or above GL) (reinforcement cut as required to facilitate demolition), complete all as specified and as directed. |
| 136 | M&L for RCC 1:2:4 type B1(using 20mm graded crushed stone aggregate) as in slab supported on walls, beams and columns in floors, roofs , landings, balconies, deck slabs and in shelves and the like complete all as specified and as directed. |
| 137 | M & L for mild steel TMT bars,10 mm dia and over , cut to length, bent to shape required including cranking, bending spirally for hoopings for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and as directed. |
| 138 | Formwork to rough finished surfaces of concrete to soffits of suspended slabs such as roof slabs, floor slab landings and similar works including supports etc complete all as specified and as directed. |
| 139 | S & F 15mm bore CP two way Angle cock screwed down for iron pipe and fixed in repaircomplete all as specified and as directed. Make : Jaquar, CERA, Hindware |
| 140 | S & F 15mm bore CP two way Bib tap screwed down for iron pipe and fixed in repair complete all as specified and as directed. Make : Jaquar, CERA, Hindware |
| 141 | S & F 32mm bore two way waste pipe fixed in repair complete all as specified and as directed. |
| 142 | Deduction to be made from BOQ for Sch 'A' Part-II (Schedule of credit) Note: Tenderers shall not quote for this schedule. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysNov 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender