Tender For Repair To Floor Tile, Toilet/ Bathrooms, Joinery And Other Misc Repair In Jco(S)/Or Md Accn & Key Pers Qtrs Under Age B/R-Ii At Mil Stn Yol
Tender Value
37 Lakhs
Estimated cost
Bid Submission
28 Nov 2026
10 days left
EMD
74000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Floor Tile, Toilet/ Bathrooms, Joinery And Other Misc Repair In Jco(S)/Or Md Accn & Key Pers Qtrs Under Age B/R-Ii At Mil Stn Yol
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering all as specified and directed. |
| 2 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified Complete all as specified and directed. |
| 3 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in ridge/flusing board of width or girth not less than 610mm Complete all as specified and directed. |
| 4 | Dismantling timber in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section (Unframed work) all as specified and directed. |
| 5 | S&F for Rolled mild steel work in roof trusses (framed) trussed, purlins crane gantries, rails and fastenings and heavy bracket framing)beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe 410- W (Gde-E-250 quality A), complete all as specified. |
| 6 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets Complete all as specified and directed. |
| 7 | S&F false ceiling of Non asbestos fibre cement building boards (E classic board), manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process confirming to IS-14862, of size 600 mm x 600 mm x 4 mm thick fixed over and including anodised aluminium powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25 mm x 25 mm x 1.5 mm thick in square pattern of grid size 600mm X 600mm . The aluminium fram work will supported on side wall with the used of aluminium 'L' section of size 25 mm x 25 mm x 1.5 angles etc. Snap grid shall be supported with hangers of 4 mm dia Galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling cleats made out of Galvanised iron flat of size 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified directed by the Engineer-in-Charge. Make:- Everest or equivalent as approved by GE |
| 8 | Dismantling timber scantlings 40 sq. cm and over Framed work (as in chowkhats) or Unframed work and over in section, in any position complete all as specified directed by the Engineer-in-Charge. |
| 9 | M & L for 2nd class hard wood timber scantling Clean swan fixed for Framed work (as in chowkhats) or unframed work all as directed. |
| 10 | Taking down chowkats or frames with shutters n,exc 1.50Sqm (without taking off shutters from the frames) complete all as specified directed by the Engineer-in-Charge. |
| 11 | Taking down chowkats or frames with shutters exc 1.50 Sqm but n. exc 4 Sqm Each (without taking off shutters from the frames) complete all as specified directed by the Engineer-in-Charge. |
| 12 | Taking down shutters n, exc 1 Sqm each complete all as specified directed by the Engineer-in-Charge. |
| 13 | Taking down shutters exc 1 Sqm and n. exc 2 Sqm each complete all as specified directed by the Engineer-in-Charge. |
| 14 | S&F Factory made fully glazed (frosted/grounds/obscured) fully guaged PVC window/Ventilator shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC Sheet for top and bottom rail on either side and as gap inserted for top anndbottom rails complete all as specified and directed. |
| 15 | S&F for Pressed steel frames for doors of size 125mm X 60mm X 1.25mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed including one shop coat of red oxide zinc chrome primer and filling frame and hold fast with PCC m-15, type B-0 using 12.5 mm graded crushed stone aggregate, all as specified and directed. |
| 16 | S&F for 35mm thick second class hard wood plain framed panelled shutters (any numbers of panels) with panels of 9 mm B.W.P. commercial ply or 12 mm vennering particle board with commercial veneering on both face, timber flat on bolts side (feather edged or veneered particles board medium density wood particles with commercial face veneers etc, complete all as specified and directed. |
| 17 | S&F for 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 18 | S&F for 35mm thick glazed and skeleton shutter open rebated and prepared to receive with sash bars edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc, size of members of shutter complete all as specified and directed. |
| 19 | M&L for two coats of synthetic enamel paint over one coat of pink primer on newly prepared wooden surfaces of any description, not otherwise described over 10cm width or girth complete all as specified directed by the Engineer-in-Charge. |
| 20 | S & F solid PVC door frame of size 50 x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube, in opening all as specified and as directed. |
| 21 | S&F for Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face wth wood free EPS, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed. |
| 22 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. all as specified and directed by Engineer-in-Charge. |
| 23 | S&F for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 24 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. |
| 25 | Dismantling boarding, any description, fixed in any position with nails or screws Complete all as specified and directed. |
| 26 | S&F 16-18 mm thick HDHMR particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. |
| 27 | S&F 18/19 mm thick Pre- Laminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. |
| 28 | External teakwood lipping 6mm thick fixed with nails complete all as specified and directed. |
| 29 | S&F for Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flap (when open) 40mm, complete all as specified. |
| 30 | S&F in repair magnet catcher with magnet for cupboards complete all as specified and directed. |
| 31 | S&F for MS butt hinges 100mm size, medium weight cold rolled mild steel, and fixed complete all as specified directed by the Engineer-in-Charge. |
| 32 | S&F for 200mm length aluminum, anodised, barrel tower bolts of extruded section and fixed complete all as specified directed by the Engineer-in-Charge. |
| 33 | S&F for 150mm length aluminum, anodised, barrel tower bolts of extruded section and fixed complete all as specified directed by the Engineer-in-Charge. |
| 34 | S&F 100mm size of aluminum handles, fabricated type anodised complete all as specified directed by the Engineer-in-Charge. |
| 35 | S&F 125mm size of aluminum handles, fabricated type anodised complete all as specified directed by the Engineer-in-Charge. |
| 36 | M&L Hasp and staple size 100mm , aluminium anodised , including bolt to hinge plate and fixed with screws complete all as specified directed by the Engineer-in-Charge. |
| 37 | S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed. |
| 38 | S&F Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including 10 mm thick square bar in grill and following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window.(ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf.(iii) MS tower bolt 150mm long - 2 No per leaf(iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf.(v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf.(vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf.(vii) Flat iron fillets of size 20X3 mm for fixing wire gauge.(viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 354/09 sheet 1/3 to 3/3.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day. |
| 39 | S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples Complete all as specified and directed. |
| 40 | S&F in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples in repair Complete all as specified and directed. |
| 41 | M&L for Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring Complete all as specified and directed. |
| 42 | S&F MS prepainted sheet type door spring heavy duty, 200mm long including roller and roller plate complete all as specified and directed. Make-Ritf/Everest |
| 43 | S&F for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n,exc 0.50 Sqm in each pane all as specified and directed. |
| 44 | S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares in n.exc 0.5 sq.m in each pane all as specified and directed. |
| 45 | Hacking old broken glass (any thickness,size, quality or description ) from metal frame/wooden frames, glazed with putty/glazes with wooden beads Complete all as specified and direcetd by Engineer in Charge. |
| 46 | Preparation of new steel and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 47 | Demolition of stone/boulders or brick masonary built in cement mortor including all quoins, arches, pillars, etc but excluding ashlar facings, dresses stone work and precast concrete articles etc, complete all as specified. |
| 48 | Walling random rubble masonry with best quality locally available stone, brought upto course, well bonded, bedded, solidly hearted and built in cement mortar 1:4, complete all as specified and directed. |
| 49 | All as per Item No 48 above, but except stone |
| 50 | M&L for Brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed. |
| 51 | M&L for plain cement concrete 1:2:4, type B1 (Using 20 mm graded crushed stone aggragate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and holdfast and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including use of form work, complete all as specified and directed. |
| 52 | M&L PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggragate) as in surface channel and drain including use of form work, complete all as specified and directed. |
| 53 | Taking down cement plaster on brick or stone walls etc, including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed. |
| 54 | M&L for Rendering 15mm thick on fair faces of brick or concrete surfaces of wall in CM 1:6 and finished even and smooth without using extra cement (Internal surfaces) complete all as specified and directed. |
| 55 | M&L for Rendering 15mm thick on stone masonry or surface other than fair faces brick or concrete surfaces of wall in CM 1:6 and finished even and smooth without using extra cement complete all as specified and directed. |
| 56 | M&L for rendering 5mm thick in cement mortar 1:3 on fair faces of RCC concrete surfaces and including applying cement slurry on bottom of slab, chajjas, fin, facias etc complete all as specified and directed. |
| 57 | M & L rendering 15mm thick in cement mortar 1:4 on external fair faces of brick work or concrete surfaces plastered surfaces finished even and smooth without using extra cement with water proofing compound as per manufacture instruction complete all as specified and directed.Note: WPC shall be measured and paid separately as supply only. |
| 58 | M&L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper over 2mm wall care putty to achieve smooth surface complete all as specified and as directed. |
| 59 | M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 60 | M&L for preparation of newly plastered surface of walls and applying two coats of cement base paint over a coat of primer complete all as specified and as directed. |
| 61 | Material and Labour for exterior painting work including complete preperation of newly/ Old Plastered Surface plastered surface and crack filling with crack seal upto 3mm where required and making good/smooth the surface with wall putty with silicon additives and sanding these surface for removal of loose particles and applying one coat of SmartCare waterproof primer (Damp Prime Suprema) on walls and chajjas with 10% of dilution of water and applying two coats of 100% acrylic smooth emulsion exterior grade with silicon additives and anti-algal properties (Apex Ultima Suprema). complete all as sepcified and directed. |
| 62 | Supply only Liquid water proofing compound complete all as specified and directed by Engineer in Charge. |
| 63 | M&L for taking down of old decayed plaster from RCC fin, facia,ceiling cleaning of all surfcae by brooming, scraping etc applying one coat of anti corrision paint to visible reinforcement and replastering the same or finishing with 1:2:4 (1 Cement:2 sand:4 mm micro chips) including necessary formwork if required as per existing surface and applying two coat of cement base paint over a coat of chalk whitingng primer including preparation and necessary scaffolding etc. complete all as specified and directed. |
| 64 | Demolition of cement concrete (un-reinforced) in ground floor and pavings n. exc 15cm thickness (below or above ground level) all as specified and as directed including removal of surplus soils/demolished materials not exc 100m and depositing complete all as specified and directed by Engineer in Charge. |
| 65 | Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc Laid, bedded complete all as specified and directed by Engineer in Charge. |
| 66 | M&L for 14 to 16mm thick green marble slab for kitchen plateform/shelf and vertical faces duly machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry including cutting and polishing of type including 15mm thick sceed bed layer of cement mortar 1:6 complete all as specified and directed by Engineer in Charge. |
| 67 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer in Charge. |
| 68 | M&L for coloured non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer in Charge. |
| 69 | S&F for glazed ceramic tiles coloured of size (300x200x7/450x300x 7)mm thick fixed in verticle surfaces, set and jointed in neat cement slurry and pointed in white and colour cement to match including 10mm thick rendering in CM 1:4 complete all as specified and directed by Engineer in Charge. |
| 70 | M&L for Mat finish, premium quality, coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar 1:6 (01 cement : 6 coarse sand) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed. |
| 71 | M&L for Mat finish, premium quality, coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in skirting, dado etc . set and jointed in neat cement slurry and including 10mm thick rendering in cement mortar (1:4) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed. |
| 72 | M&L for 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in flooring/subbase etc complete all as specified and directed. |
| 73 | Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer in Charge.. |
| 74 | M&L for RCC 1:2:4 (using 20mm gradded crushed stone aggregate) as in slab supported on walls, beams and colums in floors,roofs ,landing ,balconies,canopies,deck slabs and in shelves and the like including form work, complete all as specified. |
| 75 | M&L MS TMT bars 10mm dia and over cut to length,bent to shape required incl. cutting,cranking,hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer in Charge. |
| 76 | Taking up or down 15mm dia steel tubing and connections from wall / ceiling or laid floors including cleaning for refixing complete all as specified and directed by Engineer in Charge. |
| 77 | S&F 15mm bore medium grade galvanised tubes with all fittings and fixed complete to walls etc. complete all as specified and directed by Engineer in Charge. |
| 78 | Refixing old GI tubing 15mm bore medium grade galvanised tubes and connections in new or old position (walls, ceiling floor etc) complete all as specified and directed by Engineer in Charge. |
| 79 | Taking up or down 20mm dia steel tubing and connections from wall / ceiling or laid floors including cleaning for refixing all as directed. |
| 80 | S&F 20mm bore medium grade galvanised tubes with all fittings and fixed complete to walls etc. complete all as specified and directed by Engineer in Charge. |
| 81 | Refixing old GI tubing 20mm bore medium grade galvanised tubes and connections in new or old position (walls, ceiling floor etc) complete all as specified and directed by Engineer in Charge. |
| 82 | Taking up or down 25mm dia steel tubing and connections from wall / ceiling or laid floors including cleaning for refixing all as directed. |
| 83 | S&F 25mm bore medium grade galvanised tubes with all fittings and fixed complete to walls etc. complete all as specified and directed by Engineer in Charge. |
| 84 | S&F in repairs Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm, including bedding in cement mortar to dwarf wall fixing on RCC slab and connecting unions to pipe all as directed. |
| 85 | S&F in repairs for vitreous china wash basin white flat back, size 550x400mm and size as per available space incl brackets, cutting for and pinning in ends or brackets including fixing of waste coupling and pipe complete all as specified and directed by Engineer in Charge. |
| 86 | Supply and fixing Pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or cold with long screwed shanks and flynuts, scewed for union pipe and fixed to 15mm dia pipe complete all as specified and directed by Engineer in Charge. |
| 87 | S&F in repair 15mm bore dia of stop valves cast copper alloy screwed down high presure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer in Charge. |
| 88 | S&F in repair 15mm bore dia of conceled stop valves cast copper alloy screwed down high presure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer in Charge. |
| 89 | S&F in repair 15mm bore dia of angle valves cast copper alloy screwed down high presure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer in Charge. |
| 90 | S&F in repiars Bib taps with wall flange, 15mm bore, cast copper alloy, chromium plated, fancy type, screwed down high pressure, screwed for iron pipe or for brass ferrule fixed in repairs, all as specified. (Cat Part No OPL-15037/ VGP-81037 of 'Jaquar' or equivalent in makes mentioned in Appendix 'C'). |
| 91 | S&F in repairs Vitreous china water closet pan (pedestal pattern), white including fixing bolts etc including fixing of plastic water closet seat cover, black/white closed pattern with flat bottom and cover and mild steel chromium plated hinging device, flushing cistern etc. complete all as specified and directed by Engineer in Charge. |
| 92 | Supply and fixing plastic water closet seat, black or white closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified and directed by Engineer in Charge. |
| 93 | S&F in repairs Vitreous china squatting pan, 'Orissa pattern, size 580 x 440mm white, with intergal foot rest including flushing cistern and flush pipe etc complete all as specified and directed by Engineer in Charge. |
| 94 | S&F in repairs for 10 ltr capacity PVC valveless syphonic action type flushing cistern, low level white with inlet ball valve float and handle including brackets complete all as specified and directed by Engineer in Charge. |
| 95 | S&F in repairs 25mm dia Stainless steel curtain rod including brackets and Globes as in repairs complete pair, complete all as specified and directed by Engineer in Charge. |
| 96 | Taking down existing water proofing/ cement plaster/treatment on slab/ walls/ facias and cleaning with wire brushes roughening the surface and hacking out dirt, where directed and disposal of rubbish n,exc 50mm distance from the starting point complete all as specified and directed by Engineer in Charge. |
| 97 | M&L for 50 mm thick PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregate as in repair to padding on roof slab finishing even and smooth without using extra cement to ascertain the proper slope complete all as specified and as directed. |
| 98 | M & L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick / concrete surfaces and finished even and smooth without using extra cement mixed with WPC @ 3% by Wt. of cement (External surfaces) all as specified and directed. Note:- WPC shall be measured and paid seperately) |
| 99 | Supply & providing water proofing treatment with hyperplas fiber 4 kgs/sqm APP polymeric membrane of 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gm/Sqm) including coating the surface with water based bituminous primer @0.70 sqm/ltr, blown bitumen 85/25 or 90/15 at 1.20 kgs/sqm over primer all as specified and directed. |
| 100 | M&L for Plain cement concrete 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in sunken floors all as specified and directed. |
| 101 | M&L for Water proofing treatment of sunken portion/ Water Tank Portion/slab in two coat @1kg/sqm (each coat) using shaliurethane-BTD of STP make or equivalent mentioned in Appendix 'C' high solid content component water based liquid applied elastometric water proofing membrane as ASTMC 836 and ASTMD 6083, thickness of the membrane shall be 1.50 mm having solid content of more than 80% elongation of 500+(-) 50% laid over reinforcing layer on non woven geotextile mesh of 40/ 50 gms including applying self primer coat by diluting with 1:1 ratio @ 0.40 Kg per square metre and surface preparation including taking down existing waterproofing treatment/ plaster, complete all as per manufacturer's instructions/ specifications and as directed. |
| 102 | M&L for Rendering cement plaster 10mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (5mm thick first layer and 5mm thick second layer), mixed with water proofing compound @ 3% by weight of cement on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified. |
| 103 | S&F for 32 mm dia, 450 mm long, galvanised iron, medium grade pipe as in spout of sunken floor all as specified and directed. |
| 104 | S&F for PVC (SWR) pipes,type B,single socketed in any length with rubber ring joints laid in trenches or fixed to walls of bore 110 mm , in repairs, complete all as specified. |
| 105 | S&F for PVC (SWR) pipes, type B, single socketed in any length with rubber ring joints laid inyrenches/fixed to walls of bore 75 mm , laid in repairs, complete all as specified. |
| 106 | S&F for PVC (SWR) junction single (Single T) equal or unequal, 75 mm bore provided with oval access door, fixed in repairs, complete all as specified. |
| 107 | S&F for PVC (SWR) bend any radius with access door, 110 mm bore, fixed in repairs, complete all as specified. |
| 108 | S&F for PVC (SWR) junction single (Single T) equal or unequal, 110 mm bore provided with oval access door, fixed in repairs, complete all as specified. |
| 109 | S&F in repair for PVC (SWR) bend any radius with access door, 75 mm bore, fixed in repairs, complete all as specified. |
| 110 | S&F for 110 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified. |
| 111 | S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including chamber of PCC 1:2:4 of size 300x300x300 mm including precast cement concrete covercomplete all as specified.. |
| 112 | Disconnection of existing PVC/ferro cement/MS tank of capacity exc 250 ltr but n.exc 500 ltrs for cleaning and removing all scale and dirt etc from tanks and from mouth circulating pipes etc and hoisting if required, reconnecting and re fixing in position all as directed by Engr-in-Charge. |
| 113 | S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position of 500 liters capacity confiring to IS specification incl dismantling HDPE/PVC/cement water tank all as specificed and directed. |
| 114 | M&:L for Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved). |
| 115 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 all as specified and directed. |
| 116 | Supply & fixing pvc connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed. |
| 117 | supply & fixing 32 mm bore HDPE waste pipe for wash basin, sink, urinal etc complete all as specified and directed. |
| 118 | S&F in repairs steel plate rack of size 600mmx600mmx250mm made of stainless steel 1mm thick fixing over 40 cm long MS angle of size 25x25x3mm-02 Nos each complete all as specified and directed. |
| 119 | S&F in Repair Sheet glass shelf/Corner Shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with Stainless steel bracket guard (Standard Quality) and railing 60cm long complete all as specified and directed. |
| 120 | S&F for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engineer-in-Charge |
| 121 | Supply & fixing 600x450mm bevelled edge mirror of selected guantity glass, moulded on 6mm thick AC building board or commercial plywood and fixed to wooden pluges with cromium plated srews and cup washers complete all as specified and directed by Engineer-in-Charge |
| 122 | Supply & fixing in repair chromium plated shower rose 125mm size complete all as specified and directed by Engineer-in-Charge |
| 123 | Supply & fixing 100mm size steel locking bolts with mild steel electrogalvanised plate and bright bolt not less than 10mm dia complete all as specified and directed. |
| 124 | S & F for welded steel wire fabric,weight n. exc. 4.00 kg/sqm, fixed to steel members complete all as specified. |
| 125 | Supply & fixing in repair Brass CP mixer (center hole mixer/ wall mixer/ sink mixer ) for mixing hot & cold water screwed down for iron pipe and and fixed to 15mm dia pipe complete all as specified and directed by Engineer-in-Charge. |
| 126 | Supply & fixing CP soap dish 150mm size complete all as specified and directed by Engineer-in-Charge |
| 127 | S&F in repair Stainless steel Jet spray complete all as specified and directed by Engineer-in-Charge |
| 128 | Plain cement concrete M-15, nominal mix, type B-2, using 40mm graded mechanically crushed stone aggregate as in path/paving/hard standing, 75mm thick, surface finished broom finish without using extra cement, complete all as specified and directed. |
| 129 | M & L machine cut Kota stone slab flooring 18-20 mm thick ,laid over and incl 15mm thick cement screed /rendering in CM 1:6 ,laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl cutting, rubbing, gridding and mirror polshing complete all as specified and directed. |
| 130 | Material & Labour for kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including 10mm cement screed plaster in CM 1:4 complete all as specified and directed. (Note:- The kota stone on treads & risers shall be fixed in one piece only. No joints shall be provided. Contractor shall keep this aspect in his mind while quoting his rates). |
| 131 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 132 | S&F for door seal of length exc 0.70 m and n.exc. 1.40 m to protect from outside insects etc complete all as specified and directed. |
| 133 | Deduction to be made from BOQ for Sch 'A' Part-II (Schedule of credit) Note: Tenderers shall not quote for this schedule. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender