Tender For Conservation, Restoration & Develpment Works For Tourist Facility At Sheetla Mata Kund , Kanod , Bhallavhnagar (Udaipur)
Tender Value
1.25 Crore
Estimated cost
Bid Submission
16 Nov 2026
4 days left
EMD
2.51 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Conservation, Restoration & Develpment Works For Tourist Facility At Sheetla Mata Kund , Kanod , Bhallavhnagar (Udaipur)
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m , disposed earth to be levelled and neatly dressed : All kinds of soil |
| 2 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds ofsoils |
| 3 | Diluting and injection Chloropyrifos Emulsifiable concentrate 20% with 1% concentration for PRE-CONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which aproch is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment and excluding the cost of chemical emulsion) . |
| 4 | Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 5 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix, 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20rnm nominal size). |
| 6 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. - 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 7 | Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix |
| 8 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. M20 grade Nominal Mix / Design Mix |
| 9 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation in basements rafts, footings, straps beams, bases of columns etc. up to plinth level. |
| 10 | Columns, pillars, posts and struts etc. |
| 11 | Suspended floors, roofs landings staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam etc. |
| 12 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor V level. Thermo-mechanically Treated bars(Conforming of relevent IScode) |
| 13 | Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 14 | Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in : Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 15 | Add extra for Random Rubble stone masonry with hard stone in Square or Rectangular pillars |
| 16 | Brick work with clay flyash F.P.S. brick (IS 13757- 1993 ) of class designation 75 in superstructure above plinth level upto floor five level in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 17 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 18 | Half brick masonry in Superstructure , above plinth level upto floor V level using bricks of designation 75 Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 19 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats.or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with I Priming coat of red oxide |
| 20 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. |
| 21 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. |
| 22 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of : Above 3601 Cm2 Slabs |
| 23 | Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work (Full Edge moulding ) |
| 24 | Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete as per design approved by Engineer-in-Charge. |
| 25 | Plaster on new surface on walls in cement sand mortar 1:4 including raking of joints etc. complete fine finished :-20 mm thick |
| 26 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete |
| 27 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: :Two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. |
| 28 | Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Engineer-in-Charge. |
| 29 | 30mm thick factory made solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15 mm x15mm , top & bottom rails. M.S .frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC ‘C channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick, 95mm wide PVC sheet out of which 75 mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75 mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet shall be provided as gap insert for top rail & bottom rail. Panelling of 5mm thick PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with 7mm (5mm +2mm) thick x 15mm wide PVC sheet bending on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the ‘C Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacture’s specification & drawing.(For W.C.and bathroom door shutter). Including all door fittings such as Hinges, L-drop, Handles, Locking bolts etc. as per approved of Engineer-In-Charge. |
| 30 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : |
| 31 | Making khurras 450 x 450mm with average minimum thickness 50mm cement concrete 1 : 2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1 : 3 and one coat of neat cement, rounding edges and making and finishing the out let complete. |
| 32 | Extra if square,rectangular hollow tubelar sections are used or grill made by flats only |
| 33 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick |
| 34 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 35 | Carriage of building Rubbish Stone Metal(Grit and Ballast etc.)with lead of 10 KMs |
| 36 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth , consolidating each deposited layer by ramming and watering including lead upto 50Mtr. With all lift. |
| 37 | Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge: In lime mortar. |
| 38 | Supplying and fixing stone lintels/bed plates of approved quarry rough dressed in cement mortar 1:4 : Upto 15 cm. thick. |
| 39 | Providing and fixing double scaffolding system on the exterior side, upto five story made with 4\\" wooden member 1.5 m c/c horizontal and vertical direction joining with rassi, clamps, challies. The scaffolding system shall be stiffened with bracing, runner, connection of building if necessary with all essential safty features for the workmen etc complete as per direction of El.The lavation area of the scaffolding shall be measured for payment. The payment will be made once irrespective of duration of scaffolding. Note : This item to be used for maintence work iudiciallv |
| 40 | Fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:4 ( 1cement : 4 coarse sand) with joints finished flush. Red Sand stone size not less than 1350 Cm2, 75mm thick. |
| 41 | Supplying and fixing machine cut fine dressed Red/Pink sand stone dasa or coping, with full moulding if required laid on cement mortar 1:4 including pointing with admixture of pigment matching with the stone shade. 75 mm thick |
| 42 | Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision New Work |
| 43 | Supply and fixing Jodhpur sand stone Machine cut Kerb stone (1Ocm wide 40 cm. height) fixed in white cement sand mortar 1:4 with pigment includinq Earthwork. |
| 44 | Carriage of Earth, Sand, Lime, Morrum manure or sludge etc with a lead of 10 Km |
| 45 | Providing & Fixing Premium Quality white glazed vitreous china Sanitary Wares (IS:2556 Mark) of approved make as per direction of Engineer-in-charge including cutting and making good the wall and floor. |
| 46 | W.C. orissa pan with 100 mm vitreous china P or S trap |
| 47 | P & F European type white glazed vitreous china 1st quality Double syphonic W.C (IS :2556 Mark) with P or S trap including cutting and making good the wall and floor |
| 48 | P & F water closet Seat Covers with brass hinges complete : White |
| 49 | P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball (IS: 1703 mark) complete including cutting and making good the wall : PVC with PVC bend and superior internal fittings as per IS : 7231 |
| 50 | P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. |
| 51 | P & F C.P. Health Faucet with 1Mtr. Long Tube & Hook of approved make and heavy as per direction of Enginner-in-Charge |
| 52 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : Size 550 mm x 400 mm dia for counter top |
| 53 | P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. Flat Back (small) size 456x355x265mm. |
| 54 | P & F W.V.C. Urinal Partition Plate of approved standard make of size 630x315mm including making good the wall. |
| 55 | P & F C.P. brass Urinal Spreader for stall urinal of approved make. |
| 56 | Providing & Fixing Premium quality Bottle trap internal portion 32mm, size 250mm long wall connection pipe & wall flange as per approved by Engineer in Charge. As Per Wash Basin Qty |
| 57 | P & F 15 mm. Dia Connection Pipe of approved quality/make : PVC pipe with C.P. Brass nuts upto length, 600mm. |
| 58 | P & F Ball Cock (IS :1703 Mark) with Rod & P.V.C. Ball complete : Brass wt.Not less than 400 gm, 20mm. |
| 59 | P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. Size 600 x 450mm x 4 mm thick |
| 60 | P & F Soap Dish or Tray of approved quality/make. C.P. brass |
| 61 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge. Swan neck pillar cock 15 mm nominal size |
| 62 | P & F Grating of approved quality/make : Stainless Steel Sheet size 125mm dia. Heavy Quality of approved make |
| 63 | Drainage |
| 64 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 65 | Coupler (socket) |
| 66 | 110mm dia |
| 67 | Bend 45 |
| 68 | 110mm dia |
| 69 | Pipe Clip |
| 70 | 110mm dia |
| 71 | Bend 87 .5 |
| 72 | 110mm dia |
| 73 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metrespacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) |
| 74 | 15 mm nominal size |
| 75 | 25mm nominal size |
| 76 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,) |
| 77 | 15 mm nominal size |
| 78 | 25mm nominal size |
| 79 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: C.P. Brass bib cock,15mm nominal bore. |
| 80 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:Long body, 15mm nominal bore weight not less than 690 gm |
| 81 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc.with 37 cm long pipe and nut. |
| 82 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : Gun-metal 25mm nominal bore. |
| 83 | P & F rigid pvc pipe (IS:4985 mark) class II/ (4 kg./cm2) approved quality I make including joining the pipe with solvent cement rubber ring and lubricant: 110mm dia |
| 84 | P & F PVC Storage Tank ISi Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of aooroved desiqn :.500 litres capacity. |
| 85 | Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr.lead.: Oepth up to 0.5 M |
| 86 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work. |
| 87 | Short point (up to 3 mtr.) |
| 88 | Medium point (up to 6 mtr.) |
| 89 | Long point (up to 10 mtr.) |
| 90 | Wiring of twin control light point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 2 Nos Hot Dipped Galvanized M.S Modular box of 1.2 mm thick with earth terminal,2 Nos10 A two way Modular switch, 3 pin ceiling rose / holder / 3 way connector ,Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work. Long point (up to 10 mtr.) |
| 91 | Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work. On board |
| 92 | S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work. |
| 93 | 20 mm |
| 94 | 25 mm |
| 95 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work. |
| 96 | 1 x 1.5 sq.mm |
| 97 | 3x 1.5 sq.mm |
| 98 | 2 x 2.5 sq. mm. + 1x1.5 sq. mm. |
| 99 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. |
| 100 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work. |
| 101 | Single pole MCB (With B/C curve tripping Characteristics) |
| 102 | 6 A to 32 A rating |
| 103 | For Switch Board & AC |
| 104 | Four pole MCB (With B/C curve tripping Characteristics) |
| 105 | 50/63 A rating |
| 106 | Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work. Metal door (Three phase) IK-09 and IP-43 with Metal end box. 6 Way |
| 107 | P & F of Industrial plug and socket conforming to IEC 60309-1/2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. For additional technical parameters of product / work. IP -67 Surface/Wall mounted socket. 32 A 3 pin(2P+E) |
| 108 | Providing & Fixing of ding dong/musical chime bell as per PWD specification for electrical Works, including making connection testing etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. |
| 109 | Providing & Fixing of modular type lockable feature socket duly made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work. 6/16 A shuttered socket |
| 110 | Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work. 5 step fan regulator 2 Module 360 dgree rotating |
| 111 | Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification of Wiring accessories refer Chapter E - 07 related item & For additional technical parameters of product / work. |
| 112 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work. 10.0 Sq. mm- 4 core |
| 113 | Supplying and making one end termination with Nickel plated heavy duty brass single compression gland (as per IS 12943-1990)) SIBG type consisting of Check Nut, Gland Body, Metal Washer(3 Nos.), Outer Seal Rubber Ring, Compression Nut, heavy duty aluminium lugs (as per IS 8309 -1993) duly crimped with crimping tool, PVC tape as per IS 8337-1976 of following size of PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. 4 x 10.0 sq.mm |
| 114 | Supply and installation of high tensile low carbon steel rod molecularly bonded with 99.9 % Copper thickness (250 microns) and confirming to UL 467, IS/IEC 62561-2 of following size and length and as per point mentioned (a), (b), [c), (d), (e) below :- |
| 115 | (a) Bore a hole of dia. 100 mm of required length, Place the rod in the centre of Hole |
| 116 | (b) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, CPRI/ ERDA tested with RMS capacity of minimum 30 KA for withstanding 1 second .To ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 Kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. The compound shall be tested form NABL acredeated lab for low resistivity ( less than 0.12 Ohm - meter ) & high conductivity in nature with carbon as a major content as per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 with latest amendemnts |
| 117 | © Connect the rod with copper Strip/Conductor/Wire with suitable clamp made from tinned copper and SS 304 Bolt |
| 118 | (d) Place Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. |
| 119 | (d) Testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. |
| 120 | (e) Test certificates for confirming above standards from OEM is mandatory. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. |
| 121 | 17.2 mm thick and 3 Mtr. Long |
| 122 | Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. 8 SWG copper Wire |
| 123 | Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. 1200 mm Sweep BEE 1 Star rated (service value >=4.0 to < 4.5 ) |
| 124 | Providing & Fixing of of Double ball bearing, copper wounded capacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor ,making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. 300 mm sweep |
| 125 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. 1170mm(+/-10%) LED batten with min. lumen output 2200 lm |
| 126 | Site clearance Dy uprooting of trunk vegetation, bush, wood, trees and sapplings of girth upto 15cms and disposal of rubbish with in 50mtr. Including leveling and dressing of ground as per direction of Engineer incharae. |
| 127 | Tuman masonry by brick bats/ stones in grinded mortar of Lime Surkhi mortar 1:2/lime sand mortar 1:2 including racking and removal of all old loose plaster and cleaning the wall surface properly as per direction of Engineer Incharge. |
| 128 | Providing and laying lime Dhar on roofing as per Rajasthan, Jaipur traditional practice with lime, Surkhi, old lime powder, brick aggregate 12 to 20mm (1:2:2:2) and using Methi, Gur, Hemp, Belgiri etc. including beating and temping 100 to 150mm thick as per specifications. Including dismantling of old detoriated roofing |
| 129 | Lime Surkhi Plaster 1:2 (1 Lime : 2 Surkhi) including preparation of mortar by traditional practice (by grinding) in 3 course for base coarse and subsequent course & Loi, tamping, beating, curring till the shrinkage cracks are disappear. The work is to be done with all lead as the work is of restoration nature as per Jaipur practice including adding gur,methi & gugal on old walls including removal of all old loose and decade plaster, each coat to be done after 3 days of previous coat. 45 mm thick in four coats |
| 130 | Add extra over item no. 3.1 to 3.3.3 for Lime plaster work done over curved/circular masonary work (curved or circular surface.) |
| 131 | Khamira Colour Washing as per old traditional practice to prepare the Khamira the lime should be slaked at least for 7-10 days and regularly it should be stirred by adding cured, Gugal, for non-synthetic colour adding gum (babool gum) as per specification. Then applying prepared solution on walls three to four thin coats as desired finishing. |
| 132 | Providing & applying Lime kara 1:2 (1lime cream : 2 Zikki powder) grinding mortar with grinding mill/manually on lime base,on all flat surface in two coats.First coat applying 3mm to 4mm thick and curing properly at least 7 days,second finishing coat done after 7days of previous coat as per traditional practice.(thickness not more than 6 mm.) |
| 133 | Add extra for Lime kara work (on lime plaster base) other than flat surface as per traditional practice with all lead & lift with fine finishing complete in all respect on (a) curved surface. |
| 134 | Providing & fixing fine dressed machine cut sand stone Stone steps (Treads & risers) with round nising as per existing matching fixing in lime surkhi mortar 1:2 including pointing in lime cream and stone dust 1:1 with an admixture (50mm to 60mm thick) |
| 135 | Stucco work in lime, Surkhi, mortar (1:2) as per existingdesign work/ traditional practices by skilled craftsman,the stucco work should be done as per restoration nature, the mortar should be prepared by grinding mill adding gur,methi & gugal.. The thickness varies from 50mm to 100mm as per the design. |
| 136 | Providing & applying Lime kara 1:2 (1lime cream : 2 Zikki powder) grinding mortar with grinding mill/manually (on lime surkhi/sand plaster base) on decorative/ornamental lime plaster in two coats. First coat applying 3mm to 4mm thick and curing properly at least 7 days, second finishing coat done after 7days of previous coat as per traditional practice.(thickness not more than 6 mm.) |
| 137 | Providing and Fixing fine dressed sand stone /approved stone \\"Chajja\\" for palaces,chattries,forts and jharokas with fine dressed surface both sides and front edges should be round shape/moulding, fixing in grinded lime surkhi mortar 1:2 joint flush with proper adhesive with pigment to match the shade of stone (thickness of chajja on front edge 50mm and 75mm on fixing end) exposed surface is to be measured only. |
| 138 | Chemical treatment of sand stone to clean from yellowness, blackness, algal growth, dust, dirt oily accretions, lime & gypsum deposits, filling of cracks/ joining of gaps/ pointing, strengthening of weak stone, removal of salt effect and application of preservative coating to prevent algal growth and make the stone water proof. |
| 139 | Providing and fixing fine dressed sand stone/approved stone \\"Katahara Jali\\"(Jali for balustrade) as per existing matching and design including moulding fixing with thambli by proper adhesive and white cement with pigment including making groove etc. complete in all respect. (50mm thick.) |
| 140 | Providing and Fixing fine dressed sand stone /approved stone \\"Thambli\\" (katahara pillers including) kalash on top,fixing on dasa as per existing design for fixing of stone jalies/railings including making grooves as per required size.(a) Size 100x100x750mm including kalash with moulding. |
| 141 | Providing and fixing fine dressed sand stone \\"Todies\\" (Brackets) as per existing matching stone with moulding work with fine finishing , fixing in grinded lime surkhi mortar 1:2 including scaffolding, lead & lift complete in all respect. (c) Size : 90cm X 60cm X 10cm (exposed part only.) |
| 142 | Providing and fixing double leaf door wooden shutters made of Ist grade wood as per trditional design (Deshi pattern) planks thickness 40mm and width of Binies, Andheri 50mm and 35mm, including Adwa etc. with fittings (nails, sankal, kunda, cheri, handle and patti etc.) as per existing matching/ as per approved design with moulding/ carving complete in all respect : Sheesham wood grade Ist |
| 143 | Providing and fixing double leaf Window wooden shutters made of Ist grade wood as per trditional design (Deshi pattern) planks thickness 25mm and width of Binies, Andheri 35mm and 25mm, including Adwa etc. with fittings (nails, sankal, kunda, cheri, handle and patti etc.) as per existing matching/ as per approved design with moulding/ carving complete in all respect :Sheesham wood grade Ist |
| 144 | Providing and fixing \\"Stone Kalasha\\" as per existing matching on doms od chattries/jharokhas as per existing design & dimensions as per traditional practices, fixing of kalash carefully without damaging the doms complete in all respect. |
| 145 | Providing & fixing in lime surkhi mortar 1:2, single paitam (rebated) store doors, window and ventilator frames as per existing matching or approved quarry including removing of damaged parts of frame, the cuting of corner as per drawing complete in all respect.(d) size 125mm x 125mm |
| 146 | Flush pointing over joints of dressed stone cladding, chajjas, jali etc. with neat cement, sand & colour including racking the joints as per Jodhpur practice including all leads and lifts with grinded mortar of lime putty and stone powder mixed in 1:1 ratio and gur, methi, gugal etc. are to be mixed as per old traditional practice. |
| 147 | Providing & fixing ashlar \\"Rain water Spouts\\" (3) lines dressed as per traditional practice / existing design / approved design size 60 x 30 x 25 cm, fixing the rain water spout with lime surkhi mortar 1:2, with proper slope complete in all respect. |
| 148 | Providing and fixing of fine dressed \\"Ashlar stone work\\" (Plain work) of temple by machenical/manual system carefully with proper order and sequence, fixing with grinded lime surkhi/ sand mortar 1:2 and joints flush with lime cream and stone dust 1:1 including all scaffolding and shuttering work, the place as directed by Engineer incharge. |
| 149 | Steel-rod stitching incracked stone patties, beam,and lintels.Providing and fixing stainless steel rods of 90cms length of which 15cm on either side and cold bending at 90degrees. The stainless steel clamps to be fixed perpendicular to the crack by drilling in stone and fixing with cement and aradite mixture in such a way that the entire length of the rod is in complete contact of the stone and the bent ends are fully inserted in the cracked stone. Use 316 grade stainless steel charge per hole.steel rod charges are counted per kg.Holes with 6mm, 8mm, 10mm or 12mm dia.as per requirement of position. |
| 150 | Crack filling in masonary walls with grinded masaldar lime surkhi mortar 1:2 (adding gugal, gugal, methi, belgiri ) including cleaning the crack properly complete in all respect |
| 151 | Crack thickness above 25mm and upto 50mm (average) |
| 152 | De-vegetation from monument by removing bushes, trees including complete uprooting from the wall & roofs/structures carefully including sutaible chemical treatment to roots to avoid further growth including disposal of rubbish with in 50mtr. Lead as per direction of Engineer incharge. |
| 153 | Add extra for decorative/ornamental Lime surkhi 1:2 plaster work with fine finish making kangoora, flowers, geometrical designs upto (khat) including preparation of Lime surkhi mortar 1:2 as per tradititional practice adding gur,methi,gugal etc. Upto 25mm thick/depth |
| 154 | Add extra over item no. 3.1 to 3.3.3 for Lime plaster work done over Spherical or groin ceiling/ladao ceiling of doms.80% 3.1.2 |
| 155 | Add extra for Lime kara work (on lime plaster base) other than flat surface as per traditional practice with all lead & lift with fine finishing complete in all respect on : (a) domical surface/spherical/domical ceiling.Item no 4.8 |
| 156 | Making Gardana under ceiling/ chajja with katla stone and grinded Lime surkhi mortar 1:2 including moulding work and fine finishing with grinded Lime surkhi mortar 1:2 as per existing matching/ traditional practice completev in all respect;. |
| 157 | Making Bend -patta, Cornice, Gola & String course with katla stone and Lime surkhi mortar 1:2 (projected ) and finishing with grinded Lime surkhi mortar 1:2 including moulding/ design work as per existing matching at site complete in all respect. |
| 158 | Providing and fixing fine dressed sand stone \\"Cladding\\" (Plain dressing only) as per existing matching , fixing in grinded lime surkhi mortar 1:2 including pointing in cream and stone powder 1:1 with an admixture of pigment to match the shade of stone complete in all respect including removal of damaged cladding.(a) 50mm to 60mm thick. |
| 159 | Silt and Sludge clearance of the entire Kund with sewage pumps or with labour/sweepers etc. to clean all the water sources below and on the sides of the Kund complete and disposal of the sludge including all leads and lift to some remote dumping ground, location of such dumping ground will be the responsibility of the Contractor and he had to comply with all statutory reauirements. |
| 160 | Random Rubble stone masonary for foundation and plinth in Lime surkhi mortar 1:2 above 30cm. thick walls in : ( 1 Lime putty : 2 Surkhi including adding admixture like qur, methi etc. in mortar.) |
| 161 | Random Rubble stone masonary for superstructure, 4.50mtr. Height above plinth level/ one storey height above 30cm. thick walls in : Lime surkhi mortar 1:2 ( 1 Lime : 2 Surkhi including adding admixture like qur, methi etc. in mortar.) |
| 162 | Providing, carving and Fixing of interpretive signages in Bansi paharpur stone of size 1000x1300x50 mm on inclined plane .Engraving,painting of letters as per drawing and design. The signage stone shall be fixed on the post of same stone of size 300x 300 x 1050 above ground and 1/3 of total height of post shall be embedded in ground with necessary earthwork and concreting etc. complete as per |
| 163 | Stone Dustbin Providing/Carving/Fixing of placing of Dustbin in Bansi Paharpur stone with Carved Arch pattern and wire mash litter bin inside , over all size of dust bin will be 900x900x1200 as per detail drawing and as directed by engineer incharge complete in all respect. |
| 164 | Cast Iron Benches: Providing and Fixing Cast iron benches of size 1500x500-1800x600 approx with iron Recangular tube battens on top and rest of iron Rectangular tube battens on cast iron members and on 150 mm thick PCC 1:2:4 as per design and drawing in all recpect as per direted by Enginner-in-Charge |
| 165 | Tour Taxi(ie Sedan type four wheeler & four seater)jaipur to site and return including toll tax driver expenses (food,night stay Misc.) Including GST and other taxes and charges |
| 166 | Pumping out water caused by springs,tidal or river seepage broken water or drains and the like as per Engineer in charge |
| 167 | Providing and Fixing \\"Cobbles\\" 1OOmm thick on path way I open court yards over 40mm thick cement sand mortar 1:3, including keeping 1Omm joint between cobbles filled with cement sand mortar 1:3 complete in all respects. The mortar should remain recessed by 5mm from the top surface of the cobble stone. |
| 168 | S& F of all in one solar LED street light fixture with Integrated high efficient Monocrystalline panel with Lithium (LiFeP04) Ferro Phosphate battery with BIS approved make .luminaire should be secondary optic lenses for better distribution with delivered efficacy of> 100 Lumen perwatt.Bidder shall have in house R&D Laboratory which is recognised by ministry of Science & Technology department, Govt. Oflndia/ NABL. Bidder shall have inhouse pole & luminaire manufacturing facility. Luminaire can be supplied with Hybrid switch along with indicator to understand the source of power( either from solar or AC supply).shall have certificate tested fromMNRE approved Lab. Guarantee for total system is two years .Note: All the above should be integrated and should be 1 system. make: Bajaj/Philips I Crompton. Compact Solar LED Street Light - 35W(MONO) 18V/12.8V9Ah/12W Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender