Tender For Special Repair To Bldg No P-69 (Or Md Accn) At Chopra Lines And Otm Accn Bldg No T-05 At Fsd Samba Under Ge Samba
Tender Overview
Project Description
Tender For Special Repair To Bldg No P-69 (Or Md Accn) At Chopra Lines And Otm Accn Bldg No T-05 At Fsd Samba Under Ge Samba
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 17-Nov-2026 | corrigendum1 | BOQ | 25-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified. Note :- Work will be carried out upto 2nd storey of bldgs also as per pirection of Engr-in-charge including necessary formwok and scaffolding required as per site conditions & no extra payment shall be made on this account. |
| 2 | Rendering 10+5 mm thick on fair faces of brick or concrete surface walls in two layers, in cement mortar 1:4 , rendering is to be finished even and fair without using extra cement (up to 2nd storey with necessary scaffolding) complete all as specified |
| 3 | M&L Rendering cement plaster, 10 mm thick on fair faces of brick/concrete surfaces of wall in cement mortar 1:6 finished even and smooth w/o using extra cement complete all as specified. |
| 4 | Rendering 5 mm thick on fair faces of brick or concrete surface ceilings, in cement mortar 1:3 , rendering is to be finished even and smooth without using extra cement complete all as specified |
| 5 | Demolition of cement concrete (unreinforced) ground floor to second floors and pavings n exc 15 cm thickness (below or above ground level ) and removing the rubbish from the work site out side defence premises complete all as specified. |
| 6 | Rendering 15mm thck in CM 1:3 or Plain Cement Concrete as in sunken floors without extra cement on walls/floors and including mixing of water proofing compound (WPC shall be measured and paid separately) |
| 7 | Cleaning of dust removal to all loose existing sunken floor any material manually and with heat tark gun to get smooth plain finished surface including removing of vegetation/plantation with no loose material on surface. Repair all joints and cracks with highly elastic bituminous cold applied putty of tarplasic having penetration after setting upto 8mm. Levelling of surface to give proper slope will be done as per site requirements with Shalipatch or euqivalent make of approved by GE cold applied.Bituminous mortar and cold emulsion cum water proofing liquid of Shalikote-T-10 or equavalent make as approved by GE, created SSD condition on surface with water. Prime the surface with Tarfelt LM or equivalent make as approved by GE mixed with portable water in the ratio of 1:1 and apply @ 400gm per Sqm (as per surface condition). Apply first coat of Tarfelt LM or equivalent make as approved by GE having alongwith 200% conforming to ASTM-C-412 & having crack bridging of 8mm conforming to ASTM-C-836 with tensile strength after 7 days 0.50mm conforming to ASTM-C-412 with no diluation water on primed surface while the surface is still tacky with consumption of 700gm /Sqm. Apply 2nd coat on cured first coat with consumption @ 700gm/Sqm in opposite direction of 1st coat by brush or roller. Allow it to dry for 10-12 hrs after apply 3rd coat with consumption @ 700gm/Sqm. Ensure final curing time of 36 hrs before allowing/carrying out any further work. Conduct ponding test after minimum 7 days applying 2 coats of U V Resistand Elastomeric Exterior Axcrylic weather resistant water proof coating of Shalicryl - 215 or eauivalent make as approved by GE having elongation of 300% after curing of 14 days conforming to ASTM D-6083, for U V protection of bituminous Elastomeric Acrylic emulsified liquid membrance of Tarfelt LM or equivalent make as approved by GE to give long life and prevent its deterioration from sunlight. Note : Application of water proofing treatment will be done by authorised applicator only. |
| 8 | M&L Cement concrete type E-2, 1:5:10 ( 40 mm graded agregate) in Sunkan filling and mass concrete complete all as specified |
| 9 | M&L 40 mm dia G I tubing heavy grade galvanised laid over floors as a spout pipe in sunken floors all as specified. |
| 10 | Supply only Water proofing compound liquid. |
| 11 | M&L for repairing of concrete surfaces such as balcony, chajjas, upward or downward facias ,column, pillar, ceiling and similar items with plain cement concrete 1:2:4 type B-0 including minimum reinforcement or rendering 10-15mm thick as per site requirement in CM 1:3 without using extra cement finished even and fair complete all as specified and directed (Up to second storey bldgs and including necessory formwork and scaffolding and provision of minimum reinforcement required as per site condition also taking down or dismantling as required at site). |
| 12 | Demolition of reinforced cement concrete of any discription ground to 2nd floors and removing the rubbish from the work site out side defence premises complete all as specified. |
| 13 | M&L for Reinforced Cement Concrete 1:2:4 type B-1, (Using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs landings, balconies, canopies, deck slabs and in shelves and like , including demolition of Reinfored cement concrete of any description and in any position and removing the rubbish from the work site out side defence permises complete all as specified an as directed. |
| 14 | M&L for TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. |
| 15 | M&L for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified and directed. |
| 16 | M&L for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed |
| 17 | Complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster/demolition of cement concrete any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust. |
| 18 | M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed. |
| 19 | M&L Rendering 15mm thck in CM 1:4 on Concrete surfaces of roof finished fair & even and including mixing of water proofing compound (WPC shall be measured and paid separately) |
| 20 | M&L for water proofing treatment in the following sequences:-(a) Applying 1st course of bituminous primer conforming to IS -3384 @ 0.4 Kg/Sqm cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely (bi) Applying 2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (C) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat complete all as specified and as directed . |
| 21 | M&L for preparation of newly sufrace of APP Membrane and applying two coats of water based bituminious alumunium paint @ 200 ml per sqm etc |
| 22 | Cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified |
| 23 | Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material from the work site ouside defence premises complete all as specified. |
| 24 | Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified |
| 25 | Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 but except bricks complete all as specified |
| 26 | M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified. |
| 27 | Material and labour for Providing, cement concrete 1:2:4 type B-1 (using 20mm graded aggregate ), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed |
| 28 | Dismantling water tanks and removing to store of water storage tanks (Cap. 250 ltr to 500 ltr ) complete all as specified and directed by Engineer-in-charge. |
| 29 | Supply and fixing Rotational moulded polyethylene water storage tanks of 500 litres capacity,(cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified |
| 30 | Disconnecting of water tank of 500 ltr capacity setting aside (or lowering if required) for repairs, cleaning etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing,etc. measured separately). |
| 31 | Cleaning and removing all scale and dirt etc, from exc 250 & n exc 500 litres capacity tanks in any position and from mouths of circulating pipes etc, and disinfection completely by making all the arrangements and writing date of cleaning on side of tankscomplete all as directed. |
| 32 | Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 15 mm bore pipe, including making connections complete all as specified and fixed. |
| 33 | Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and fixed. |
| 34 | S&F in repair PVC tank covers required for 500 ltr to 1000 ltr PVC water tanks complete all as specified and fixed |
| 35 | Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store,complete all as specified and as directed. |
| 36 | Taking up or down steel tubing of 20 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed. |
| 37 | Supply and fixing 16 mm nominal outer dia Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11, having thermal stability for hot & cold water supply, including all Plain CPVC SDR 11 fittings & brass threaded fittings on walls/ceiling or laying in floors,including fixing the pipe with clamps. This includes jointing of pipes & fittings with one step CPVC solvent cement, complete all as specified and as directed. |
| 38 | Supply and fixing 20 mm nominal outer dia Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11, having thermal stability for hot & cold water supply, including all Plain CPVC SDR 11 fittings & brass threaded fittings on walls/ceiling or laying in floors,including fixing the pipe with clamps. This includes jointing of pipes & fittings with one step CPVC solvent cement, complete all as specified and as directed. |
| 39 | Supply and fixing tubes 'medium grade' galvanised, 20 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified |
| 40 | Supply and fixing tubes 'medium grade' galvanised, 25 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified |
| 41 | Repair to existing PVC pipe/CI pipe including making the joints water tight by using suitable material including cleaning if required and refixing of any dia. Note : Work to be carried out up to 2nd storey bldg in any condition of working place/area |
| 42 | Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the premises. Complete all as specied and directed. |
| 43 | Material and labour Non - skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4. Complete all as specied and directed. |
| 44 | Material and labour glazed ceramic coloured Digital tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified. |
| 45 | Material and labour Non - skid Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4. , complete all as specified |
| 46 | Description all as item No 45 but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete. |
| 47 | Taking down shutters of any description n.exc 1.00 Sqm each and removing from the site all as specified & directed. |
| 48 | Taking down shutters of any description exc 1.00 Sqm and n.exc. 2.00 sqm each and removing from the site all as specified & directed. |
| 49 | Taking down chowkats or frames with shutter (without taking off shutter from the frame) n.exc 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified. |
| 50 | Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm & n.exc 4 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified. |
| 51 | S&F pressed steel frames of size 125mm x 60mm made out of size 1.25mm thick MS sheet for doors single rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified. |
| 52 | S&F pressed steel frames of size 105mm x 60mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified. |
| 53 | Supply and fixing Factory made, plain framed, panelled shutter (two Panel) 35mm thick, 2nd class Hardwood with lock rail and panel of 9 mm B.W.P commercial ply. The size of rail and stiles as per as per IS:1003 (Part-I),kiln seasoned and chemically pressure treated complete all as Specified |
| 54 | Supply and fixing 35mm thick 2nd Class hard wood glazed,gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars,stiles and rails as specified in SSR Part-I Sec 8 clause 8.24 (a) complete all as specified |
| 55 | S&F Solid PVC Door Frame of size 50mm x 95mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all as specified |
| 56 | S&F Factory made solid PVC Moulded door shutter 28 to 30 mm thick (Stiles) with particle board core with 2, 4 ,or 6 raised panel design with 2 mm thick moulded Prelam PVC sheet on the front face & 2 mm Prelam PVC sheet on back face, to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the framme at site as per specification and drawing, complete all as specified and as directed. |
| 57 | Repair/ easing of wooden door any type, glazed or panelled, by trimming the side of door shutter where rubbing with chowkhat, unscrew the hinges screws and lift the door and fix with screws, tightening of wire mesh etc |
| 58 | Pressed steel cup board frame of MS sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 as in filling to back of chowkats including butt hinges 100 mm long. Piano hinges measured separately. |
| 59 | Prelaminated MDF board 19 mm thick as in shutters/shelves (exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame worknincluding lipping (15 mm thick three sides and 20 mm thick lipping hinge side) around the shutter complete all as specified and as directed by Engr-in-Charge. |
| 60 | Dismantling Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar |
| 61 | M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 incl dismantling Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortarias |
| 62 | M&L 16 to 18 mm thick green udaipur marble in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 |
| 63 | M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified. |
| 64 | Machine cut kota slab flooring 18 to 20mm thickness over cement screed base laid and jointed with gray cement slurry mixed with pigment to matches the shade of the slab including rubbing and polishing,and 20mm thick screed bed or bedding layer of mortar in cm 1:6 for laying floor finishes including Cement concrete type B-1 1:2:4 (20mm graded aggregate) as sub base, 25mm thick complete all as specified |
| 65 | Machine cut kota slab skirting 18 to 20mm thickness over cement screed base laid and jointed with gray cement slurry mixed with pigment to matches the shade of the slab including rubbing and polishing and taking down cement plaster on brick or concrete surface including racking out joints hacking for key scrubbing down with water etc and Rendering 10 mm thick in CM 1:4 as for backing coat of wall tiles complete all as specified |
| 66 | S&F 3.0 mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), Including hacking out old broken glass (any thickness,size quality or description) , Complete all as specified. |
| 67 | S&F 3.0 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), Including hacking out old broken glass (any thickness,size quality or description) , Complete all as specified. |
| 68 | Supply and fixing in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified fixed with stainless steel wire staples. |
| 69 | S&F butt hinges of mild steel cold rolled medium weight of size 100mm as specified. |
| 70 | S&F Aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified. (ISI Marked) |
| 71 | S&F Aluminium handles, fabricated type, anodised Size-100mm, anodised section and fixed complete all as specified. (ISI Marked) |
| 72 | S&F Aluminium alloy, anodised, sliding door bolt Size- 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. |
| 73 | S&F aluminium hanging floor door stopper,Twin rubber stopper,size 100mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 74 | S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified. ( ISI Marked) |
| 75 | S&F in repair aluminium bottom door seal with brushes, length 1.2 mtr, fix with screw, suitable for wooden door complete all as specified. |
| 76 | Supply and fixing in repair mild steel helical ordinary rat tail rod pattern springs 300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed. |
| 77 | Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings like bend,branch pieces, connectors, heel rest bend etc and removing from site all as specified and directed |
| 78 | Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge. |
| 79 | Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified . |
| 80 | Supply and fixing UPVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified |
| 81 | Supply and fixing UPVC(SWR) type B pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified |
| 82 | Supply and fixing, UPVC (SWR) , bends for 75 mm bore , complete all as specified |
| 83 | Supply and fixing, UPVC (SWR) , bends with access door for 75 mm bore , complete all as specified |
| 84 | Supply and fixing, UPVC(SWR) , bends for 110 mm bore complete all as specified and as directed by Engineer-in-charge. |
| 85 | Supply and fixing, UPVC(SWR) , bends with access door, for 110 mm bore complete all as specified and as directed by Engineer-in-charge. |
| 86 | S&F UPVC (SWR) , reducers 110 mm dia complete all as specified. |
| 87 | S&F UPVC (SWR) vent cowl 75 mm dia complete all as specified. |
| 88 | Supply and fixing in repair UPVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed. |
| 89 | S&F in repair, UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified. |
| 90 | S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings) |
| 91 | S&F in repair Sink Cock with swinging casted spout (Wall Mounted model) with wall flange complete all as specified |
| 92 | S&F in repair Bib Cock with wall flange cast copper alloy, chromium plated fancy type ,complete all as specified. |
| 93 | S&F in repair 15mm bore angle valve with wall flange , cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified. |
| 94 | S&F in repair 15mm bore CP Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified. |
| 95 | S&F in repair 15 mm bore CP Bib taps Long Body , fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified complete all as specified. |
| 96 | S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified |
| 97 | S&F in repair Chromium plated, towel ring , complete all as specified. |
| 98 | S&F in repair Corner Glass Shelf (with Bracket) as per directed by Engr-in-charge. |
| 99 | S&F in repair PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore. |
| 100 | S&F in repair Brass chromium plated shower rose with or without swivel joints, 125mm size, including fixing to steel pipe or union |
| 101 | S&F in repair stainless steel soap dish holder complete all as specified. |
| 102 | Supply and fixing in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 103 | S&F in repair waste coupling of chromium plated brass 32 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basin all as specified . |
| 104 | S&F in repair waste coupling of chromium plated brass 40 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basin all as specified . |
| 105 | S&F PVC connection 15mm size with PTMT nuts of length 450mm. |
| 106 | S&F PVC connection 15mm size with PTMT nuts of length 600mm. |
| 107 | S&F in repair Vitreous China, wash basin white, flat back , size 400mmx300 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass. complete all as specified and as directed by Engineer-in-charge.. |
| 108 | S&F in repair full pedestal for WHB complete all as specified. |
| 109 | S&F in repair PVC valveless,syphonic action type, flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and as directed by Engineer-in-charge. |
| 110 | S&F in repair WC Orissa pattern white with integral foot rest 580x 440 mm including L bend, & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified.(Rate of including in taking out and removal of old WC seat unhygienic condition) |
| 111 | Supply and fixing in repair Vitreous china ware pedestal type water closet white, with 'P' or 'S' trap including self closing seat cover, closed pattern with flat bottom,complete all as directed. |
| 112 | Supply and fixing in repair for bevelled edge mirror of size (600x450mm), selected quality glass approved size , mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with SS screws and cup washers |
| 113 | Supply and fixing in repair sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 610mm x 460mm bowl size 560mm x 410mm x 200mm complete with CP waste coupling & PVC waste pipe complete all as specified |
| 114 | S & F Kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size (30\\"x36\\"x10\\") fixed with steel fastners or steel screw complete. |
| 115 | S&F in repair stainless steel lock grating plain/hole size 100 mm dia including embeding in tiles with white cement. |
| 116 | Preparation of new plastered or unplastered surfaces of ceilings to achieve smooth and even surface and applying three coats of white washing complete all as specified and as directed by Engineer-in-charge. |
| 117 | Material ad labour for preparation of new plastered surfaces of walls & applying two coats oil bound distemper over a coat of wall care putty of 1to2 mm thick and one coat of primer complete all as specified. |
| 118 | Preparation of new plastered/ concrete surfaces of walls to achieve smooth and even surface and applying two coats of Weather proof exterior emulsion paint and one coat of primer (up to 2nd storey with necessary/scaffolding) complete all as specified and as directed by Engr-in-charge. |
| 119 | Preparation of old decorated brick /concrete, plastered /un-plastered surfaces of ceilings, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, oil, greasy spots , rubbing with sand paper and applying one coat of white wash on ceiling, complete all as specified and directed. |
| 120 | Preparation of old decorated brick/concrete/ plastered/unplastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying Two coat of oil bound distemper on walls, pillars,cornices surface including making good uneven surface/holes with birla wall care putty 1to 2mm thick and one coat of primer coloured in same shade where ever required etc. complete all as specified and directed. |
| 121 | Preparation of old decorated brick/concrete/ plastered/unplastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying Two coats of Weather proof exterior emulsion paint and one coat of primer on walls, pillars, cornice etc (upto 2nd storey with necessary scaffolding complete all as specified and directed. |
| 122 | Preparation of new painted wooden surfaces having width/girth exceeding 10 cm including necessry putty filling with knife of same colour where required to achieve smooth and even surface and applying two coat of synthetic enamel paint on wood surfaces of any description over a coat of pink primer ( up to 2nd storey with necessary scaffolding) complete all as specified and directed |
| 123 | Preparation of old painted wooden surfaces having width/girth exceeding 10 cm including necessry putty filling with knife of same colour where required to achieve smooth and even surface and applying one coat of synthetic enamel paint on wood surfaces of any description ( up to 2nd storey with necessary scaffolding) complete all as specified and directed |
| 124 | Preparation of new painted steel surfaces having width/girth exceeding 10 cm including necessry rubbing with sand paper or grinding by hand grinder to achieve smooth and even surface and applying two coat of synthetic enamel paint on steel surfaces over a coat of red oxide primer ( up to 2nd storey with necessary scaffolding) complete all as specified and directed |
| 125 | M&L for 50mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed. Please Enable Macros to View BoQ information |
| 126 | M&L for 50mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Tender Published
Tender notice published.
CompletedCorrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 6 daysBid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender