Tender For Repairing, Fitting And Fixing Of Ms Penstock Gate Of Size 1500 Mm × 1800 Mm Including Other Allied Works At 73, Manik Bandyopadhyay Sarani Road, Beside Girder No. 94 Under Kudghat Unit/S&D Department
Tender Value
Ref. Documents
Estimated cost
Bid Submission
14 Nov 2026
8 days left
EMD
4500
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
24 Paraganas South → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairing, Fitting And Fixing Of Ms Penstock Gate Of Size 1500 Mm × 1800 Mm Including Other Allied Works At 73, Manik Bandyopadhyay Sarani Road, Beside Girder No. 94 Under Kudghat Unit/S&D Department
BOQ
| Sl. No. | Item Description |
| 1 | Supplying to site empty cement polythene bags(capacity 50kg) in good condition including stacking, incedental charges etc. all complete (capacity 50 kg). |
| 2 | Materials delivered and stacked at site Medium Sand(Finenses moduls 1.8 to 2) |
| 3 | Labour charges for filling empty cement gunny bag / polythene bag (capacity 50 kg) with all kinds of earth (wet or dry), sand or agreegates(stone/brick) and sewing as done in case of cement bags,( tying with a knot after filling will not be accepted),and stacking with in a lead of 30 metre as per direction of Engr-in-charge(cost is excluding the cost of any types of filling materials). NB:-Volume of earth/ sand filled bags shouldn ot be less than 0.028 cum/ bag. |
| 4 | Dumping in position earth/sandfilled gunny/polybags (capacity50 kg) within a lead of 30 metre inclusive of all lifts. |
| 5 | Dewatering by pumps including all leads, lifts and making all arrangements of disposal, where continuous flow of water from a source other than natural or ground water is encountered in case of emergency maintenance works related to leakage, breakage and making wet connections. [Note :- In case of any other situation demanding such emergency dewatering. use of this item is to be approved by the Superintending Engineer/Tender Accepting Authority. This item shall be executed on the specific direction duly supported by proper clarification of the E.I.C. who will be satisfied in absolute discretion that such work has not been necessitated due to any natural source of water or any fault of the Contractor |
| 6 | Fabrication , Supply, erection and commissioning of new Slide type vertical lift regulator service gates of Distributories /BranchCanal /Minor Canal/Channel as per IS: 5620 - 2000/Latest Revision consisting of skin plate, vertical and horizantal grider, stiffener etc. made of MS material consisting of angle , channel, beam, plate, flat, etc. conforming to IS : 2062 -2011/latest revision manufactured as per approved drawing and direction of Engineer in charge. The Cost includes cost of Materials, Machinaries , Manpower, Cutting, Aligning, drilling, Welding, Finishing, Consumables, Carriages and all overheads with all leads and lifts complete as per specification (without painting). |
| 7 | Cost for dismantling different types rubber seal from gate shutter as per direction of E.I.C. The cost includes cost of man power employed for dismantling, hire charges of tools & tackles, scaffolding and safety equipments etc including carriage loading & Gate shuteer size upto 10 Sq.m |
| 8 | Cost for supplying and fifling fixing of bulb/musical node/J- type rubber seal (Make : Universal Moulders & Engineer/Popular Rubber Works (Pvt) Ltd/SAB Industries/Unique Polymer Works/equivelant approved make conforming to lS : 11855 -2011/Latest Revision) for different types of gate as per direction of E.I.C. The cost includes cost of man power employed for fitting fixing, cost of rubber seal, hire charges of tools & tackles, scaffolding and safety equipments etc including carriage loading & unloading but excluding supply of ms clamp/ flat plate, bolts, nuts and washer. solid bulb: size- 40⌀ 140 X 12 mm |
| 9 | Supplying of M.S flat for clamping Rubber seal with hole as per direction of EIC. |
| 10 | Supplying of M.S bolts with nut for clamping Rubber seal as per direction of EIC |
| 11 | Surface cleaning of metal surfaces by chemical cleaners and then by hand with emary paper, wire brush and power tool cleaners and removing dust and preparation o f surface including cost of all materials, labour, machinery, scaffolding, etc., complete with initial lead for sand upto 1 km and all lifts. |
| 12 | Painting of embedded parts, all types of gates, stoplogs and barscreen/ gratings etc on prepared surfaces with one coat of inorganic zinc silicate primer (airless spray preferred)70+/ - 5 micron and two super coats with a total thickness of 300 microns (each 150+/- 5) of solventless coaltar epoxy paint each coat 150 microns ( total 300 microns) including cost of all materials, labour, scaffolding etc., complete with all leads and all lifts. |
| 13 | Removing earth/sand filledpolybags/gunnybags from the channel bed/slope and initially depositing the same near channel bank at a place as directed by the Engineer-in Charge for measurement of Bag. & then disposing off the same at a distance not less than 150 metre from the channel site. |
| 14 | Dismantling and taking out the broken MS gate and guide channel from the existing position by chain pulley block, tripod and necessary gas cutting and other lifting arrangements. |
| 15 | Repairing of existing lifting gear assembly and replacement of worn-out bushes, bearings with other components including lubrication as required. |
| 16 | Repairing of existing spindle & lead screw assembly including cleaning, checking of threads, alignment, lubrication and rectification as required. |
| 17 | Supply, fitting and fixing of base plate, studs, nut-bolts and washers to replace the old and broken base plate, studs, nut bolt as required. |
| 18 | Repairing of existing M.S. guide channel, including welding, straightening, alignment, cleaning, lubrication etc. as required. |
| 19 | Mfg. supply and installation of MS gratings as per existing dimensions. |
| 20 | Installation of manufactured MS gate and channel in its position by necessary civil work and fitting, fixing with nut bolts, studs including lowering the whole assembly. |
| 21 | Underwater Diver charges Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender