Tender For Reinforcement Of Sarei L.I. Projects Under Jamankira Block In Sambalpur District Of L.I. Division, Sambalpur
Tender Value
7.58 Lakhs
Estimated cost
Bid Submission
13 Nov 2026
0 days left
EMD
7587
Bank guarantee accepted
Document Fee
4720
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Sambalpur → Odisha
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Reinforcement Of Sarei L.I. Projects Under Jamankira Block In Sambalpur District Of L.I. Division, Sambalpur
BOQ
| Sl. No. | Item Description |
| 1 | Part-A |
| 2 | Earthwork in excavation of foundation in hard soil including dressing & levelling of bed within initial lead of 50mt. & lift of 1.5mtr etc complete as per the direction of the Engineer-incharge. |
| 3 | Earthwork in excavation of foundation in hard soil such as Hard stiff clay, stiff black cotton, hard red earth, shales, moorum ordinary gravels etc within 50m.Initial lead and 1.5m. Initial lift including rough dressing and levelling the bed and depositing the excavated materials within initial lead at nearby the worksite for reuse including breaking clods and stacking rubble for spreading and leveling as the case may be etc complete as per direction of the Engineer-in-charge. (Excavation by mechanical means 60% & manually 40%) |
| 4 | Filling in F&P with excavated materials in layers not exceeding 0.30m including breaking clods within 50m. initial lead including leveling the tranches as the case may be etc complete as per direction of the Engineer-in-charge.(Quantity by means of Mechanical 60% & mannually 40% |
| 5 | Filling in foundation & plinth with sand including watering & ramming etc complete as per the direction of the Engineer-incharge. |
| 6 | Cement concrete (1:4:8) with 4cm size h.g.b. crusher broken metal of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc. complete as per the direction of the Engineer-incharge. |
| 7 | Fly Ash Brick 25cm X 12cm X 8cm size masonary having crushing strength 75 kg/cm² with dimensional tolerance ± 2% in cm(1:6) in foundation and plinth complete as per the direction of the Engineer-incharge |
| 8 | Cement concrete (1:2:4) with 12mm size black h.g.b. crusher broken chips of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc complete as per the direction of the Engineer-incharge. |
| 9 | Rigid smooth centering & shuttering for R.C.C. works including false work & dismateling then after including cost of materials in ground floor complete an directed by the Engineer-incharge. (a) Walls & fins |
| 10 | Labour charges for MS reinforcement for RCC work including cutting, bending & tying the grills and placing in position including cost of binding wire 18 to 20 gauge & HYSD steel bar ( FE 415/ FE 500 ) |
| 11 | R.C.C. work in C.C. (1:2:4) including hoisting & laying & curring for 28days using 12mm. Size clean black hard granite crusher broken chips of approve quality and from approve quarry including cost taxes conveyance charges of all materials to the worksite with supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 12 | 12mm cement plaster in cement mortar (1:6) finished smooth to brick work after racking out joints including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 13 | Cement punning over plastering including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 14 | Writing charge of required information and data on both side of the transperancy pillar including supplying of approved paints and required material for writing etc. complete as per the direction of the Engineer-incharge. |
| 15 | Fitting of un plasticised 200 mm dia meter dia PVC Pipe for all classes including jointing the pipe with solvent cement by non-head application method including fitting and fixing of required no. of PVC Tee for outlet and PVC Shaddle and PVC Riser nipple for fitting air valve, equal Tee etc. including cost of PVC Pipe, cost of Solvent Cement, transportation of Pipe complete including conveyance pipe from village to worksite and testing of pipe line etc. complete as per the direction of the Engineer-incharge. |
| 16 | Supplying of 200 mm dia unplasticised rigid UPVC pipe ivory grey in colour having specific gravity of 1.40 to 1.46 gms/ cc of straight length of 6 (six) meter for potable water supplies conforming to IS - 4985/ 2000 of BIS - Ammendment - 2 read with Table - 1 of IS - specification bearing ISI marks for working pressure Cl - I UPVC pipe to withstand pressure of 2.5 kgf/cm² respectively & the specification and manufacturer's name should be prominently marked on body of each pipe as per the latest Ammendment of IS - 4985. It includes the cost of sockets in case of plain ended pipe. PDI test are to be conducted and should be marked on body of each pipe and report is to be obtained from CIPET, Bhubanweswar, necessary approval of authority including transportation to work site in complete shape |
| 17 | Filling the foundation and plinth with excavated material as directed by the Engineer-incharge. A) Hard Soil |
| 18 | 15 HP CentrifugalMonoblock pumpset total head of 24 mtr capable to discharge 1700 LPM with 15 HP/11.25 KW squirrel cage induction motor fitted with bronze impeller TB-2 of iS 318/1981, companion flanges & class 'F' insulation suitable for operation 415 volt + 6% - 15%, 3 phasde, 50 Hz aC power supply, suction/delivery = 100x100 mm with BEE star rated energy efficiency pump & as per IS-9079/2002 with overall efficiency 62 to 65% of reputed brand having wide dealership network for easy availibility of spares |
| 19 | Control panel with automatic star delta starter sheet steel enclosure vsuitable for operation of squirrel cage induction motor up to 15 HP with 16 Amp.(AC-3) duty contractor at 415 volt+6%-15%, 3 phase, 50 Hz AC supply with over load relay range 8.9 to 13.5 Amp & No volt coil with electronic timer suitable for operation at voltage range of 300 to 440 V. The starter should provide dependable protection against over load and single phasing fitted with Volt meter, Ammeter, MCB in complete shape including indicator lamp |
| 20 | Cost of 63 Amp -400 V.T.P. Main Switch confirming to IS No.4064 |
| 21 | 4 KVAR Capacitor |
| 22 | Motor Hood (size 0.45x0.45x0.60 mtr ) made with 18 SWG cold rolled mS sheet with one coat of red oxide primer and two coats of smoke gray / navy blue enamel paint both side (inside & outside) suitable to cover centrifugal monoblock Pump set from 10 to 15 HP and having provision for attachment with the groves on rear side of the panel board |
| 23 | Base frame for panel ( size 0.40x 0.20 m ) and for Motor ( size 0.50x 0.27 m ) made with 3\\" size MS channel having suitable holes for fitting of Panel board and different size & make 3 phase centrifugal monoblock pumpset from 10 to 15 HP, coloured with one coat of red oxide primer and two coats of smoke gray enamel paint |
| 24 | 3 x 16 mm² Tarpedore cable XLPE ( cross link polyethylin ) confirming to IS: 7098 (Part-II) including laying below 0.90 mtr of the ground and filling the excavated materials including watering and ramming |
| 25 | 100 mm dia nominal bore GI pipe having wall thickness 4.5 mm electrical resistance welded of medium class confirming to IS - 1239 (pt - 1 of 2004) with socketed at one end and the other end protected with plastic thread protector. The socket confirming to IS - 1239 (pt - II / 1992) with latest amendments in random length of 4 to 7 mtrs. Each pipe should bear ISI certification & manufacturer's name/ trademark |
| 26 | 100 mm dia GI Bend IS No. 1239(pt-II/1992) |
| 27 | 100 mm dia GI flange IS No. 6392 / 1971 |
| 28 | 100x100x25 mm GI Tee with plug for priming |
| 29 | 200 mmx100 mm PVC/G.I./M.S. Reducer |
| 30 | 100mm C.I. Foot Valve should be of swing type friction less with single disc confirming to iS - 4038/1979 of reputed brand |
| 31 | 100mm C.I. N.R. Valve double flanged swing type PN - 1.0 as per IS:5312 part - I with by-pass arrangement |
| 32 | 50 mm dia CI AR valve with saddle and riser pipe confirming to IS 14845 with ISI mark |
| 33 | 200 mm dia PVC Equal tee ( 4 kgf/cm²) confirming to IS - 4995 / 1988 with latest ammendment |
| 34 | 200 mm dia PVC end cap ( 10 kgf/cm²) confirming to IS - 4995/1988 with latest ammendment |
| 35 | 200x200x110 mm PVC/GI Raiser tee set with bend closing and opening arrangement |
| 36 | 200 mm dia PVC coupler ( 4 kgf/cm²) agricultural PVC fittings confirming to IS - 4995/1988 with latest ammendment |
| 37 | Construction of out let for Tee Tank |
| 38 | Electrical installation and energisation |
| 39 | Labour charges for installation of 15 HP MB Motors including transportation from village to work site, fitting & fixing of base frame, fitting & fixing suction and delivery pipe to motor, other fitting materials including cutting, welding etc. including Misc. Welding charges for \\"Z\\" joint, \\"S\\" bend, etc. complete as per the direction of the Engineer-incharge. |
| 40 | Cost of river embankment cutting, cleaning ; fitting of suction & delivery fittings with flanges, bend, foot valve, sluice valve, NR valve etc including cost 1/8\\" rubber insertion, Nut nolt, white lead paint etc vomplete |
| 41 | Part-B |
| 42 | Construction of 3 phase 11 KV Line as per REC standard confirming to RE Rules 1956 with 300Kg. 9 mtrs.long PSC Pole ( cost excluded ) support in 80Mtrs. Span 55 sqm. AAA Conductor, 11 KV \\"V\\" cross arm with required nos.of 11KV T &C disc.Insulators and 11KV Pin insulator,carping & padding of poles, danger board at each pole,anticlimbing devices. Stay set at each bending Point and double stay at end point with 18mm G.I. H.T. Stay, concreting of stay with anchor plate,guarding at road crossing etc. including cost of materials,labours, transportation, inspection and commissionng etc. complete. |
| 43 | Construction and errection of 11/0.4KV , D.P. mounted substation of different capacity confirming to RE Rules 1956 mounted on 2.44mtr. Long structure , supported in 300 Kg 9mtrs. Long PSC Poles, Transformer hard channel and top channel made of 2.8mtrs. long 100X50X6 mm M.S. Channel, Transformer belting on 2.8 mtrs. long 50X50X5 mm M.S. angle (all REC.SPN.Std F-3) with all accessories like3 poles 11 K.V. HG Fuse (F-5) & AB Switches (F-9) both mounted on 2.5 mtrs. long 75X40X6 mm M.S. Channel and supported by 1mtr. long 50X50X5 mm M.S. angle with 3nos. 11 KV lightening Arrestors and distribution box, Pipe earthing(F-2), including cost of 50 sqmm. 3.5 core PVC Cable carping and padding of poles, danger board at each poles, Anti climbing Devices & all other necessary fitting i.e. required size nuts & bolts, brackets Cable sockets etc., construction of barbed wire fencing with double leaf MS Gate with metal spreading, including cost of all materials , labour transportation complete with liasoning for testing inspection & commissioning ( excluding cost of PSC pole & including cost of Transformer ) 25 KVA Sub-station |
| 44 | 10 mtr 200 kg PSC pole |
| 45 | Boundary wall of S/S with metal spreading & MS Grill gate |
| 46 | Electrical earthing Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender