Defence Statutory Bodies & Commissions/Committees Closing in 8 days TDR #58361829

Tender For special Repair To Bldg No Tw/44 At Mtn Arty Bde, Fd Wksp Pump And Misc Connected Works And Provn Of Open Shed With Hard Standing Surface For Genr Set Of Age B/R And Age E/M Under Ge Tenga

Issued by Statutory Bodies & Commissions/Committees · kameng, Arunachal Pradesh
Tender Value
35.80 Lakhs
Estimated cost
Bid Submission
24 Nov 2026
8 days left
EMD
71600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
kameng → Arunachal Pradesh
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for special Repair To Bldg No Tw/44 At Mtn Arty Bde, Fd Wksp Pump And Misc Connected Works And Provn Of Open Shed With Hard Standing Surface For Genr Set Of Age B/R And Age E/M Under Ge Tenga

BOQ

Name of Work:-
Sl. No. Item Description
1Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off from the site, complete all as specified & directed.
2M&L for 25 mm thick PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in sub floor complete all as specified & directed.
3M&L for 15 mm thick screed bed in CM 1:4 for laying floor tiles, complete all as specified and directed
4M&L for light shade Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.
5M&L for light shade Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.
6M & L for 10mm thick rendering in CM 1:3 on fair faces of brick work or concrete surfaces finished rough to receive tiles .
7M & L for 450x300x7mm thick glazed coloured ceramic tiles on vertical surface of wall set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade complete all as specified and directed.
8Dismantling of wall and ceiling board or insulation boards/slabs/blanckets/any thickness including cover fillets
9M & L for providing 4mm thick \\"E\\" Board in ceiling with galvanised iron snap frame of 'T' section 24 x 38 x 0.70 mm wall/ceiling angle 25x25x0.35mm thick and hanging with 4mm GI wire all fixed arrangement will be done as per manufacturer instruction incl two coat of oil bound distemper over one coat of white wash complete all as specified and directed
10S & F for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing
11S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame complete all as specified and directed.
12Taking down of cement or cement lime plaster/tile work any description from brick or stone wall etc. including raking out of joints, hacking for key, scrubbing down with water etc.
13M&L rendering 15 mm thick cement plaster on external surface in CM 1:6 on brick & concrete surfaces and finished even and smooth (without using extra cement) all as specified and directed.
14Material and labour for 10mm thick rendering in cement mortar (1:6) on brick or concrete surfaces finished even & smooth W/O using extra cement complete all as specified and directed
15M&L for Preparing new plastered surfaces of walls and applying Two coats of cement base paint over one coat of white wash surfaces of walls complete all as specified and directed
16M&L for Preparing new plastered surface of wall applying two coats of distemper oil emultion over a coat of white wash complete all specified and directed
17Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar and removal of rubbish from site, complete all as specified and directed.
18M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in cooking platforms in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including moulding of edged,complete all as specified and directed.
19M&L for 20mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including moulding of edges if reqd, complete all as specified and directed.
20Hacking out old broken glass (any thickness, size quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones.
21S & F sheet glass 3mm thick ordinary quality and glazing with oil putty/glazing clips/beadings in squares n exc 0.50 Sqm in each pane complete all as specified and directed.
22M&L for Toughned glass as in wall , hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes as required complete all as specified and directed.
23Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in hard/dense soil all as specified and directed.
24M&L for hard core broken to guage n exc 63mm with broken stone/ boulders complete all as specified and directed.
25M&L for PCC type C-2, 1:3:6 (40mm graded aggregate) as in Cement concrete in foundations, filling and mass concrete sub-base, floors and pavings, post & struts etc complete all as specified and directed.
26M&L for 100 mm thick PCC type B-1, 1:2:4 (20mm graded aggregate) as in sub-base, floors and pavings etc complete all as secified and directed.
27M&L for Providing Plain cement concrete type B-1, (1:2:4) using 20 mm graded aggregate in roof kerbs or mud stops, rounded or chamfered on edges complete all as secified and directed.
28Removing excavated material n.exc 50m and depositing where directed at a level n exc 1.5m above the starting point.
29M&L for 100 mm thick PCC type B-2, 1:2:4 (40mm graded aggregate) as in sub-base, floors and pavings etc complete all as specified and directed.
30M&L for Chequered cement concrete tiles 20cm x 20cmx 25mm thick,set,jointed and pointed in neat cement slurry layer finish with grey cement & pigment with glossy finish, with 15mm thick screed bed 1:6 cement mortar all as specified & directed.
31Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard / dense soil all as specified & directed.
32M&L for rolled mild steel for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc, Fe- 290 (Gde E- 165).complete all as specified and directed
33S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed .
34M&L for Preparation of new steel Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of black japan paint over a coat of red oxide complete all as specified and directed.
35Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed
36Demolition of cement concrete in floors not exceeding 15 cm thick in ground floor (below or above ground lelvel) and in any position all as specified and directed.
37M & L for PCC 1:4:8 type D2 (40 mm graded stone agreegate) cement in foundation filling and mass concrete complete all as specified and directed .
38M & L for reinforced cement conceret (Nominal Mix) type B0, 1:2:4 , 12.5mm graded in walls, retaining walls, basement walls, ballast walls and the like, any thickness, above top footing incl att headpilaster and buttresses all as specified & directed.
39Use & Waste of flat Formwork to faces of Baffle walls, retaining walls, abutments, parapets and staircase railings and similar work incl att pillasters, buttresses etc, vertical or curved and finished fair complete all specified and directed.
40M & L for rendering 15 mm thick on fair faces of brick work or conceret surface in CM 1:4 with WPC 3% by weight of cement finished even and smooth finishing without using extra cement completed all specified and directed.Note :- WPC will be measured and paid seperately
41Supply only integral water proofing compound all as specified and directed.
42M & L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required un incl cranking bending spirally for hooping for columns, hooking ends and binding with end incl mild steel wire (annealed) not less then 0.9 mm dia or securing with clips.
43M & L for Reinforcement cement concrete type B1 1:2:4 in slabs supported on wall, beams and columns in floors, foofs, landing, balconies, canopies, deck slabs and in shelves all as specified and directed
44Use & Waste of flat fromwork to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work not exceeding 200 mm thicks , (Horizontal OR slopping) all as specified and directed.
45M&L for PCC (1:2:4) type B-2 (40 mm graded stone aggreegate ) cement concrete in surface of channels and drain complete all as specified and directed.
46Dismentling wrought iron or mild steel of any description not otherwise provided for complete all as specified and directed.
47M & L for two coats of synthetic enamel paints to steel surface over a coat of red oxide primer exc 10 cm width or girth incl preparation of new surfaces all as specified and directed.
48Material & Labour for Light /fan point wiring with 1.5 sq mm (nominal area), PVC insulated unsheathed (FRLSH), 1100 volts grade, multi-stranded copper conductor, in and including PVC casing capping of adequate size with all fittings and accessories including PVC boxes for housing the switches (Make of box Prestoplast,Prestoteak), including PVC insulated and unsheathed (FRLSH)single core multi-stranded copper conductor cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.
49Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm , two to three terminals complete all as specified & directed.
50Supply & fixing switch piano flush type (ISI marked), single pole, one way 6 Amp, 240 Volts complete all as specified & directed.
51Supply and fixing LED light fitting 1 x 20 Watt 220 volt AC decorative box type with driver, holder including LED tub light connecting up with three core flexible copper conductor cable of size from ceiling rose complete all as directed.
52S&F of new generation energy saving and environmental friendly long life LED building security light made up of innovative die cast aluminium housing high power LED as lighting source with IP - 66 power consumption 45 watt complete input voltage of 150-240 Volt (nominal rated voltage 240 Volt) complete including twisted 3 core copper cable of size 1.5 Sqmm dia for connecting phase, neutral and earth from ceiling rose to light length as required at site,GI bracket 32 mm dia pipe and 02 numbersclmaps, all fixing arrangements such as fastners, bilts, nuts washers etc all as specified and directed.
53Supply and fix sheet metal enclosures for DBs double door when MCBs to be used 230 volts 4 way 200 Amp rated busbar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board.
54S&F MCB SPN having breaking capacity 10KA, 32 Amps, 'C' curve,240 V complete all as specified and directed.
55S&F MCB SP having breaking capacity 10KA, 6 to 32 Amps, 'C' curve, 240 V complete all as specified and directed.
56Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15 mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as specified and directed by Engineer-in-Charge.
57Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric cables with stranded aluminium conductor, 1100 volts grade, of 10 Sqmm 2 core complete all as specified and directed.
58Excavation in trenches in any type of soil not exc 1.5 mtrs wide and not exc 1.5 mtr in depth for laying of pipe/ cables/ poles/fencing posts etc and getting out complete all as specified and as directed.
59Returning filling in any type of soil including spreading leveling watering and well ramming in layers n.exc 25 cm complete all as specified and as directed.
60Supply and laying 50mm HDPE Pipe PE-80, PN 10 Blue Line Confirming to IS 4984-2016 of black colour with clamps and fittings for fixing on wall/ laid in tenches complete all as specified and directed.
61Supply and fix Air termination, single pointed, copper rod 12mm dia 300 mm long
62S&F GI strip 32x6mm as earth continuity conductor buried in ground for loop earthing or through wall on insulators as required.
63Supply and fix Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex head screw. Please Enable Macros to View BoQ information
64Supply and fix Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex head screw. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58361829
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 35.80 Lakhs
LAST DATE 24-11-2026
Authority
Authority Name Military Engineer Services
Work Description Tender for special Repair To Bldg No Tw/44 At Mtn Arty Bde, Fd Wksp Pump And Misc Connected Works And Provn Of Open Shed With Hard Standing Surface For Genr Set Of Age B/R And Age E/M Under Ge Tenga
Basic Detail
Tender No 8293/E8
Bidding Type Tender
Location
City kameng
State Arunachal Pradesh
Key Dates
Publish Date 03 Nov 2026
Submission Date 24 Nov 2026
Open Date 01 Dec 2026
Finance
Tender Value 35.80 Lakhs
Tender Fee 500
EMD 71600
Exemption Available
Document List
8385b44b-678d-4e91-9dc4-4284f2dbd138.html
BOQ_894159.xls
Tender.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 03, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 24, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 8 days
Dec 01, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 15 days

Tender Documents

Download All (ZIP) ↓
html

8385b44b-678d-4e91-9dc4-4284f2dbd138.html

xls

BOQ_894159.xls

pdf

Tender.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender