Tender For Addition/Alteration And Special Repairs To Various Married Accommodations At Bhopal Military Station
Tender Value
12.14 Crore
Estimated cost
Bid Submission
02 Dec 2026
17 days left
EMD
9.32 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bhopal → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addition/Alteration And Special Repairs To Various Married Accommodations At Bhopal Military Station
BOQ
| Sl. No. | Item Description |
| 1 | Note: (i) Please refer schedule 'A' notes before quoting the tender. (ii) Amount of Schedule of credit shall be deducted off line by the department. |
| 2 | Demolition to cement concrete in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and directed. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the permises complete all as specified and directed. |
| 4 | M&L for 25mm thick PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in bedding layer for laying and fixing floor, levelling course etc. complete all as specifed and directed. |
| 5 | Hacking of cement concrete flooring including cleaning of surfaces etc. complete all as specifed and directed. |
| 6 | M&L for double charged vitrified ceramic tiles 8 to 9mm thick (square/rectangular) polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, as in floors etc.laid with cement based high polymer modified quick set tile adhesive (water based) Type 2 conforming to IS:15477, in average 6mm thickness and pointed in epoxy adhisive complete all as specified and directed. |
| 7 | M&L for Non skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. laid with cement based high polymer modified quick set tile adhesive (water based) Type 1 conforming to IS:15477, as in average 6mm thickness. and pointed in white or coloured cement to match the shades of tiles complete all as specified and directed. |
| 8 | M&L for double charged vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, as in skirting etc. laid with cement based high polymer modified quick set tile adhesive (water based) Type 2 conforming to IS:15477, in average 6 mm thickness and pointed in epoxy adhisive complete all as specified and directed. |
| 9 | M&L for coloured glazed ceramic tiles as in vertical surface 600 x 300 x 7mm thick set and jointed laid with cement based high polymer modified quick set tile adhesive (water based) Type 1 conforming to IS:15477, in average 3mm thickness and pointed in white or colour cement to match the shade of tiles complete all as specified and directed. |
| 10 | M&L for heavy duty flooring tiles, harsh weather & UV resistance, high abrasion resistance, MOH hardness >6 thickness 10mm thick, area of each tile not less than 0.09 sqm , anti slip type laid in floors, steps, edges etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with and including 15mm thick rendering in cement mortar 1:4 complete all as specified and directed |
| 11 | Demolition of stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar complete all as specified and directed. |
| 12 | M&L for granite of black / green / imperial red of any type machine cut as in shelves / steps / counter tops, 20mm thick, set and jointed in cement slurry over & including screed of 15mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified.Note:- Single piece should be used in steps / cills / jambs /shelves or equivalent as approved by GE. |
| 13 | M&L for kota stone slab 20 to 25mm thick in single piece in riser of steps skirting, dado and pillar laid over cement screed and jointed with including 15mm thick screed bed in CM 1:6 etc set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and pre finished nosing in treads of steps of Kota stone slab and the front portion of the tile, for a minimum length of 75mm from and including the nosing, must have grooves running parallel to the nosing at centers not exceeding 25mm for anti slippery surface etc complete all as specified and directed. |
| 14 | M&L for machine cut kota stone slab 20 to 25mm thick in riser of steps, skirting, dado in single piece over 10mm thick cement plaster 1:3 jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing complete, all as specified and directed. |
| 15 | M&L for plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified & directed. Note:- The unit rate include for use of form work (straight or curved). |
| 16 | M&L for PCC in 1:4:8 type B1 (using 40mm graded crushed stone aggregate) 100mm thick as in sub base concrete complete all as specified and directed. |
| 17 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in foot path, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand concrete complete all as specified and directed. |
| 18 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required concrete complete all as specified and directed. |
| 19 | M&L for cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation, filling, sub base and mass concrete complete all as specified and directed. |
| 20 | M&L for PCC M-15 (nominal mix) as in coping including formwork and finishing, complete all as specified and as directed. |
| 21 | Demolition to brick work built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work and precast concrete areicles complete all as specified and directed. |
| 22 | M&L for old size burnt brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 all as specified and directed. |
| 23 | M&L brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:6 complete all as specified and directed. |
| 24 | Taking down cement plaster on brick or stone walls etc including raking out joints, hackig for key, scrubbing down with water in cement or cement lime plaster any description complete all as specified and directed. |
| 25 | M&L for rendering 10mm thick ready mix plaster on internal wall by adding potable water by weight of material as mentioned by manufacturer ready mix plaster shall comply with IS- 1661-1972, IS-2402-1963, IS-2250-1981 and shall confirm 28 compressive days strength 10-15 MPA bulk dencity 1600-1800 kg/cum and pull out bond strength-> 0.5 MPA omplete all as specified and directed. |
| 26 | M&L for rendering 5mm thick ready mix self curing plaster on ceilling by adding potable water by weight of material as mentioned by manufacture ready mix plaster shall comply with IS- 1661-1972, IS-2402-1963, IS-2250-1981 and shall conform 28 compressive days strength 10-15 MPA bulk dencity 1600-1800 kg/cum and pull out bond strength-> 0.5 MPA complete all as specified and directed. |
| 27 | M&L for rendering 15mm thick (in two layers - first layer 10mm thick with readymix plaster and outer layer 5mm thick readymix waterproof plaster) on outer wall walls by adding potable water by weight of material as mentioned by manufacturer. Ready-mix plaster shall complies with IS 1661-1972, IS 2250-1981, IS 2402-1963 and shall conforms the compressive strength @ 28 days- 10-15 Mpa/ Bulk density- 1600-1800 Kg/Cum and pull out bond strength->0.5MPA complete all as specified and directed.Note:- The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 15.00m height all as specified and directed. |
| 28 | M&L rough cast plaster upto cill height above ground level with under coat of cement mortar (1:3 ) of 10mm thick, and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even complete all as specified and directed. |
| 29 | Supply only water prooofing compound all as specified and directed. |
| 30 | M&L for preparation of newly plastered surfaces and applying two coats of acrylic distemper over coat of putty as approved complete all as specified and directed.Note:- The putty shall be measured and paid separately. |
| 31 | M&L for complete removal of exiting treatment on wall surfaces and applying two coats of acrylic distemper, white or tinted over a one coat of putty complete all as specified and directed.Note:- The putty shall be measured and paid separately. |
| 32 | M&L for applying two coats of water based elastomeric exterior wall water proof acrylic (Prime less high build water based elastomeric exterior wall water proof acrylic coating for exterior surfaces) designed with weather resistant acrylate polymers, UV resistant and good hiding and spreading, developing a strong inter coat adhesion with substrate and features such as waterproofing, UV protection, anti-algae resistance, crack bridging of elastic films covering hair line cracks, long term protection, colour variants, preparation of surface by cleaning the surfaces till it is free from dust, grease and flaking paint, any unstable paint to be removed, using high pressure wash or scraper, whichever is appropriate complete all as specified and as directed.Note:-1. Application for vertical surface fresh plaster.2. Use water based elastomeric exterior wall water proof acrylic directly from the container. Stir contents well before use.3. Brush/Roller apply a self-priming coat of water based elastomeric exterior wall water proof acrylic on the vertical wall surface in SSD condition, diluting 1 ltr with 100ML clean potable water. Allow it to dry for 4 to 6 hrs.4. Apply a coat of water based elastomeric exterior wall water proof acrylic without dilution as water proof top coat, either by roller or brush with force coverage at the rate of 3.7 to 4.1 sqm/litre to achieve DFT of 100-110 microns. Allow it to dry for 4 to 6 hrs. Lighter shades base on the top of dark colours need additional coat of finishing.5. An addition coat should be applied in case of horizontal surfaces like top of windows, edges, parapet wall etc. Allow the coating to full air cure for 7 days. |
| 33 | M&L for complete removal of exiting treatment on wall surfaces complete all as specified and directed. |
| 34 | M&L for preparation of newly plastered or previously untreated ceiling surfaces and applying two coats of white wash complete all as specified and directed. |
| 35 | M&L for applying white wall care putty 1 mm thick on walls complete all as specifed and directed. |
| 36 | M&L for complete removal of exiting treatment on ceiling and applying two coats of white wash complete all as specified and directed. |
| 37 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each complete all as specified and directed. |
| 38 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm and not exc 4.0 Sqm each complete all as specified and directed. |
| 39 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete all as specified and directed. |
| 40 | S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. and including supply and fixing following items as approved by Engr-in-Charge : (a) Stainless Steel (304 Grade) finished butt hinges 125mm - 3 Nos per leaf(b) Stainless steel (304 Grade) finished tower bolt 200mm long - 2 Nos per leaf(c) Stainless Steel (304 Grade) finished handles 200mm - 2 Nos per leaf. Material test certificate and authentication should be compulsory provided by the manufacturing company : For Internal/Balcony/Main Doors. |
| 41 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x100mm comprisingof virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applyingPVC solvent cement and screwed with fullbody threaded star headed SS screwshavingminimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 modules ofelasticity 900 N/mm2 and resistance tospread of flame of Class A category withproperty of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/lugs/SS dash fasteners of required dia andlength complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid forseparately).Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 42 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x125mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugsor SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 43 | S&F factory made ISI marked WPC flush door shutters 35mm thick, comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. and including supply and fixing following items as approved by Engr-in-Charge : (a) Stainless steel (304 Grade) finished butt hinges 125mm - 3 Nos per leaf(b) Stainless steel (304 Grade) finished tower bolt 200mm long - 2 Nos per leaf(c) Stainless steel (304 Grade) finished handles 200mm - 2 Nos per leaf(d) Stainless steel (304 Grade) finished sliding door bolt/aldrop 16 x 300mm - 1 No per leaf(e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf. Material test certificate and authentication should be compulsory provided by the manufacturing company : For Internal/Balcony/Main Doors. |
| 44 | S&F factory made 30mm thick 100% Solid WPC ( Wood polymer Composite ) laminated wire mesh door shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cum manufactured by \\"RAJSHRI\\" an ISO 9001-2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter. XTN aluminum mosquito mesh is inclusive and combinly panel area of door except stiles and rails to be panelled with mesh with self tapping round headed screws at required distance, screws and edges covered with feathered PVC edge beading all around of mesh and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer-in-Charge, and including supply and fixing following items as approved by Engr-in-Charge : (a) Stainless steel (304 Grade) finished butt Hinges 125mm - 3 Nos per leaf(b) Stainless steel (304 Grade) finished tower bolt 200mm long - 2 Nos per leaf(c) Stainless steel (304 Grade) finished handles 20mm - 2 Nos per leaf(d) Stainless steel (304 Grade) finished floor door stooper - 1 No per leaf Material test certificate and authentication should be compulsory provided by the manufacturing company : For Internal/Balcony/Main Doors. |
| 45 | S&F powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 46 | S&F framed work such as grills, gratings, steel gate, purlin etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 gde E-165 complete all as specified and directed. |
| 47 | S&F factory made 18mm both side laminated HDHMR board in modular kitchen carcasse made of minifix joint with 1mm same colour edge banding including fixed with nut, screws and washers fevicol, nails complete all as specified and directed. |
| 48 | S&F fixing factory made 18mm acrylic HDHMR board in modular kitchen shutters with 1mm same edge bending on edges for kitchen cabinets/cupboards etc. including fixed with nut, screws, washers, nails all as specified and directed. |
| 49 | S&F factory made 12mm thick both side laminated HDHMR board in modular kitchen carcasse made of minifix joint with 1mm same colour edge banding including fixed with nut, screws and washers fevicol, nails complete all as specified and directed. |
| 50 | S&F factory made 9mm both side laminated board, interior grade, prelaminated both sides with decorative choice laminations, including fixed with nuts, screws, washers, nails all as specified and directed. |
| 51 | S&F powder coated stainless steel SS 304 sensys intergrated soft close hinges having size 103 x 64mm finish of nicle / silver complete all as specified and directed. |
| 52 | S&F continuous (piano) hinges, 30mm flaps stainless steel bright finish SS(304) grade complete all as specified and directed. |
| 53 | S&F magnetic catches for cupboards with plastic body and striking plate not less than 40mm including letting in and fixed complete all as specified and directed |
| 54 | S&F mortice lock brass 4 levers vertical type with handle, size 100mm complete all as specified and directed. |
| 55 | Supply only 125mm brass finish handle for cabinet shutters fancy type bright finish complete all as specified and as directed.Note :- ISI maked and shape as approved by GE. |
| 56 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperure 1.40 mm and fixed and with stainless steel wire staples fixed complete all as specified and directed. |
| 57 | S&F 4mm thick sheet glass, ordinary quality and glazing with ol putty in square not exc 0.5 sqm in each complete all as specified and directed. |
| 58 | S&F 4mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in pane complete all as specified and directed. |
| 59 | S&F in repairs stainless steel tubing of 20mm dia chromium plated minimum 1.00mm wall thickness as in curtain rod complete including 02 Nos stainless steel brackets / finials fancy type, stops fixed with stainless steel screws etc all as specified and directed Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered as approved by Engr-in-Charge. |
| 60 | Demolition of AC pipe of any dia complete all as specified and directed |
| 61 | S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed. |
| 62 | S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed. |
| 63 | S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 64 | S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 65 | S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 66 | S&F 75mm PVC (SWR) junction double, (Single T), equal or unequal complete all as specified and directed. |
| 67 | S&F 75mm PVC (SWR) junction double, (Double T), equal or unequal complete all as specified and directed. |
| 68 | S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 69 | S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 70 | S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 71 | S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 72 | S&F 75mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 73 | S&F 100mm dia grating doom of PTMT (Minimum weight 25 gms) complete all as specified and directed. |
| 74 | Taking up or down 15mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. |
| 75 | Taking up or down 20mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. |
| 76 | S&F 16mm CPVC pipes SDR 11 and plain CPVC SDR 11 with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed. |
| 77 | Refixing 15mm bore dia GI steel tubing and connection in new or old position (walls, ceiling, floors etc) complete all as specified and directed. |
| 78 | S&F 20mm CPVC pipes SDR 11 and plain CPVC SDR 11 with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed. |
| 79 | Refixing old 20 mm GI steel tubing and connection in new or old position (walls, ceiling, floors etc) complete all as specified and directed. |
| 80 | S&F in repairs 15mm bore bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferulle and fixed complete as specified and directed. |
| 81 | S&F in repairs 15mm bore stop cock, cast copper alloy, chromium plated with long shank and cut (concealed type), screwed down, screwed for iron pipe or union and fixed in repair complete as specified and directed. |
| 82 | S&F in repairs 15mm stop valves / angle valve, cast copper alloy chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete as specified and directed. |
| 83 | S/F in repairs brass chromium plated shower rose 125mm in size with or without swivel joints any size incl fixing to steel pipe or union, complete as specified and directed. |
| 84 | S&F in repairs vitreous china squatting pan \\"Orissa\\" pattern size 580 x 440mm white, with integral foot rest (exculding flushing cistern and flush pipe) including cement concrete bedding complete all as specified and directed. |
| 85 | S&F 20mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete as specified and directed. |
| 86 | S&F 15mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete as specified and directed. |
| 87 | S&F tubular towel rail chromium plated 20mm dia 'D' type 60cm long between flanges complete all as specified and directed. |
| 88 | S&F in repairs 10 Ltrs PVC flushing cistern low level white with inlet pipe, ball valve, float valve and handle including brackets complete all as specified and directed. |
| 89 | S&F PVC connection 15mm size with PTMT nuts of length 450 mm complete all as specified and directed. |
| 90 | S&F in repairs sink without drainage board made of stainless steel 1.00mm thick SS 304 grade kitchen or laboratory with plugs, washers, PTMT waste 40mm and waste pipe including bedding in cement morter to dwarf wall or including fixing in granite and connecting union to pipe bowl size 535mm x 455mm x 203mm glossy finish etc. complete all as specified and directed. |
| 91 | S&F in repairs vitreous china wash basin, white, flat back, size 550mm x 400mm including brackets and PVC waste pipe etc complete all as specified and directed. |
| 92 | S&F in repairs brass chromium plated central hole basin mixer with regular spout , popup waste system and 450mm long braided hoses with connection and nuts complete all as specified and directed. |
| 93 | S&F sink mixer with swinging spout (wall mounted model) chromium plated brass with connection and nut complete all as specified and directed. |
| 94 | S&F in repairs brass chromium plated wall mixer with non telephonic shower arrangement for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 95 | S&F in repairs 600mm x 450mm bevelled edge mirror of thickness 5 to 6mm selected quality glass, fixed with brass screws and cup washers complete all as specified and directed. |
| 96 | S&F towel ring chromium plated complete all as specified and directed. |
| 97 | S&F in repairs stainless steel plate rack complete assembeled set of (Size: 31 x 36 x 10 inch) fixed with screws as specified and directed |
| 98 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps,cills, sunshades, shelves, lintels, etc.;and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 10cm girth complete all as specified and directed. |
| 99 | S&F wall seperator wall clamps for SWR (PVC) 110mm + 75mm drainage pipes supply for pipe supporting clamping - two pipes of PVC dia 110 mm (4\\") and 75 mm (3\\") down take pipes running togethar fixing done with clamping system consists of profile bracket + continuous slotted 'C' channel + U bolt rubber sleeve mounted system running vertically with wall distance 100mm (4\\"): Pipe Support Clamping made of: 1. Profile Bracket having Wall Distance 100mm (4\\") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32mm x 3mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted \\"C\\" Channel with ribs to be used of size 450mm (18\\") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material 48mm x 3mm. 3. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 100 mm (4\\") - 2 Nos. 2. Continuous Slotted C Channel of Size 450 mm (18\\") - 1 No.; 3. U Bolt Rubber Sleeve mounted for 110 mm (4\\") Pipe Dia. - 1 No., U Bolt R/M for 75mm (3\\") Pipe Dia. - 1 No. 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63mm (2 1/2\\") - 4 Nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jodhpur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System . REF DRG NO. CEJZ/TD/102.Make: Shaivi or equivalent as approved by GE. |
| 100 | S&F wall seperator wall clamps two 20mm Water Supply Pipes Supply of Tollet Water Supply Pipe 3/4\\" (20mm) - 2 Nos. downtake pipes fixing done with Pipe Supporting Clamping System having Profile Bracket+ Slotted C Channel + U Bolt R/M System -1. Domestic Water Supply Down take lines 3/4\\" GI-2 nos. from Terrace to 1st & Ground Floor Vertical Fixed line with wall distance 4\\": Pipe Support Clamping made of: 1. Profile Bracket Wall Distance 4\\" made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079); material size 32mm x 3mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method-ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921 and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 13 with Serration as per DIN 6923. 2. Slotted \\"C\\" Channel B3 Type to be used of size 10\\" (Continuous Slotted \\"C\\" Channel with ribs) made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material 48mm x 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7mm approx, Zn Al Flake coated with noise absorbing transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923-Zn Al Flake coated. Hotdip Galvanizing as per IS 2629 (1985)-610 grams/m2 (>85 microns). Material Grade: IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty: 1. Profile Bracket Wall distance 4\\"-2 Nos. 2. Continuous Slotted C Channel of B3 Type Size 10\\" - 1 No.; 3. U Bolt R/M for 3/4\\" GI pipe Dia. - 2 nos. 4. Justi Khilla GI coated 2 1/2\\"-4 Nos. Fixing details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jodhpur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System . REF DRG NO. CEJZ/TD/102.Make: Shaivi or equivalent as approved by GE. |
| 101 | S&F wall seperator wall clamps for SWR (PVC) 75mm drainage pipes supply for pipe supporting clamping - pipes of PVC dia 75mm (3\\") down take pipes running togethar fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 100mm (4\\"): Pipe Support Clamping made of: 1. Profile Bracket having Wall Distance 100mm (4\\") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32mm x 3mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted \\"C\\" Channel with ribs to be used of size 450 mm (18\\") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material 48mm x 3mm. 3. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 100mm (4\\") - 2 Nos. 2. Continuous Slotted C Channel of Size 450mm (18\\") - 1 No.; 3. U Bolt Rubber Sleeve mounted for 110 mm (4\\") Pipe Dia. - 1 No., U Bolt R/M for 75 mm (3\\") Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63mm (2 1/2\\") - 4 Nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jodhpur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System . REF DRG NO. CEJZ/TD/102. Make: Shaivi or equivalent as approved by GE. |
| 102 | S&F mild steel work in supporting frame for chajjas, shed, ducts etc. grade conforming to Fe 410-0 or Fe310-0 all as specified and directed with crimp bend at edges. |
| 103 | S&F pre- painted galvalume aluminum zinc coating GI Based corrugated steel sheeting 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, chajjas, fixed with self tapping screws complete all as specified and directed. |
| 104 | Dismantling fencing wire mesh, any type complete all as specified and directed. |
| 105 | S&F PVC coated chain link fencing including linewires, any mesh, size and type to any type of standards, rails, straining bolts, etc.including provission of binding wire complete all as specified and directed |
| 106 | M&L for mild steel round bars conforming to Gde I (IS: 432 part-I) 8 to 10mm dia in bands, straps, clamps, hooks (pins) fixed in pillars of gate/fencing post for holding barbed wire fencing, chain link fence, etc cut to length, bent to shape required complete all as specified and directed |
| 107 | Dismantling posts or struts (wood, steel or RCC) any section embedded in concrete, masonry, brick work, including taking out embedded portion and making good disturbed ground complete all as specified and directed. |
| 108 | S&F for mild steel works as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc and flat iron fillets for securing wire mesh similar work conforming to Fe-290 Gde E-165 etc all as specified. |
| 109 | S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers and one hexagonal or square nuts, exc 5cm and n.exc 10cm complete complete all as specified and directed |
| 110 | Excavating in post holes in any type of soil (or similar holes) each n. exc. 0.5 cu.m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, including removing of surplus soil complete all as specified and directed |
| 111 | M&L plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified. |
| 112 | M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats synthetic enamal paint over one coat of red oxide primer complete all as specified and directed. |
| 113 | Taking down existing old roof treatment of any description , any type including removal old tar felt, screed, etc complete all as direcetd. |
| 114 | M&L for rendering 15mm thick on concrete surface, roof top surfaces in cement mortar ( 1:4) mixed with water proofing compound all as per manufacturer's instructions and finished the surfaces even and smooth without using extra cement complete all as specified and directed. Note:- The water proofing compound shall be measured and paid separately. |
| 115 | M&L for 40mm thk PCC (1:2:4) B0 using 12.5 mm graded crushed stone aggregate as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc., mixed with approved water proofing compound all as per manufacturer's instructions on the roof surface to achieve requisite slope complete all as specified and directed.Note:- The water proofing compound shall be measured and paid separately. |
| 116 | Preparation of roof top surfaces, Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric water proofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer in-Charge.Note:- 6 Hrs interval between two coats will be maintain & the work will be carried out through company applicator duly got approved from GE in writing before incorporation and paid only after receiving of the warranty certificate from the company. |
| 117 | M&L for water proofing treatment to RCC sunken slab (not exceeding 45cm depth of sunken) as specified below complete all as specified and directed.:- (a) Applying 15mm plaster in cement mortar 1:3 with WPC on raised vertical surface.(b) Cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc.(c) Creating fillet coving of 50 x 50mm with polymer modified mortar on the junction of slab and walls.(d) Apply first coat of two component modified polymer coating on the horizontal and verticle surface.(e) Provision of glass fiber mesh of 2 x 2mm immediately on above coating.(f) Applying second coat of two component modified polymer coating after 72 hrs.(g) Cement concrete 1:4:8 over the coating as per requirment(h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5mm.(j) Filling the gap between the wall opening and saintary pipe with non shrink cementitious grout complete as specified. Plan area shall be measured.Note:- The work will be carried out through company applicator duly got approved from accepting officer in writing before incorporation and paid only after receiving of the warranty certificate from the company. Please Enable Macros to View BoQ information |
| 118 | M&L for water proofing treatment to RCC sunken slab (not exceeding 45cm depth of sunken) as specified below complete all as specified and directed.:- (a) Applying 15mm plaster in cement mortar 1:3 with WPC on raised vertical surface.(b) Cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc.(c) Creating fillet coving of 50 x 50mm with polymer modified mortar on the junction of slab and walls.(d) Apply first coat of two component modified polymer coating on the horizontal and verticle surface.(e) Provision of glass fiber mesh of 2 x 2mm immediately on above coating.(f) Applying second coat of two component modified polymer coating after 72 hrs.(g) Cement concrete 1:4:8 over the coating as per requirment(h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5mm.(j) Filling the gap between the wall opening and saintary pipe with non shrink cementitious grout complete as specified. Plan area shall be measured.Note:- The work will be carried out through company applicator duly got approved from accepting officer in writing before incorporation and paid only after receiving of the warranty certificate from the company. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysDec 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender