Tender For special Repair To Swimming Pool Incl Replacemnt Of Pool Tiles, Internal Lightning And Allied Infra Under Ge Jaipur At Jaipur Mil Stn
Tender Value
1.12 Crore
Estimated cost
Bid Submission
20 Nov 2026
14 days left
EMD
1.87 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Swimming Pool Incl Replacemnt Of Pool Tiles, Internal Lightning And Allied Infra Under Ge Jaipur At Jaipur Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Item Rate BoQ 82596/E8 BoQ_Ver3.0 Item Rate Normal INR Only INR Select, Excess (+), Less (-) Less (-) Tender Inviting Authority: CWE JAIPUR Name of Work: SPL REPAIR TO SWIMMING POOL INCL REPLACEMNT OF POOL TILES, INTERNAL LIGHTNING AND ALLIED INFRA UNDER GE JAIPUR AT JAIPUR MIL STN CA NO: CWE/JPR- OF 2026-27 Bidder Name : PRICE SCHEDULE(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only ) NUMBER # TEXT # TEXT # NUMBER # TEXT # NUMBER NUMBER TEXT TEXT # NUMBER # TEXT# TEXT # NUMBER # NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER # NUMBER # TEXT TEXT NUMBER # NUMBER # DATE NUMBER # NUMBER # TEXT # NUMBER # SNo Item Description Item Code / Make Qty Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency Rate in Figure Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category TOTAL AMOUNT Without Taxes TOTAL AMOUNT With Taxes Rate in Words Total Amount |
| 2 | Demolition of cement concrete (unreinforced) including tiles in ground floors and paving not exceeding 15cm thickness (below or above ground level) and removal of same from outside MOD land complete all as specified and directed. |
| 3 | Demolition of brick work or stone boulder masonry built in cement mortar complete all as specified and directed. |
| 4 | M&L for brick work with sub-class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 5 | M & L for Brick work with sub-class `B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed. |
| 6 | Dismantling of floor hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish of the premises complete all as specified and directed. |
| 7 | M&L for 25 mm Thick PCC 1:2:4 type B0 under floor tiles complete all as specified and directed. |
| 8 | M&L for Non skid matt finish coloured ceramic tiles 7mm to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floor set and jointed in neat cement slurry and pointed in coloured cement match the shade of tiles over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 9 | M & L for Coloured Glazed ceramic tiles in vertical surface 300x450/600x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick backing coat on surfaces other than fair faces of brick work in CM 1:4 complete all as specified and directed. |
| 10 | M& L for 10-15 mm thick endura maxgrip tiles of size 300mm x 300mm with 3 mm spacers set and jointed using approved waterproof chemical Tile adhesive and pointed in epoxy grout to match the shade of tiles after cleaning the gaps properly by blowing air in gaps complete all as specified and directed. |
| 11 | Providing and applying waterproofing to vertical/Horizontal surfaces of swimming pool walls using two-component polymer-modified cementitious slurry in two coats with surface preparation, curing, including materials, labour, and all necessary scaffolding complete all as specified and directed. |
| 12 | M & L for Ceramic Pool tiles for vertical surface, 7 to 8 mm thick of low water absorption less than 3.0% and MOR more than 23 N/mm2 incl pool fittings like Internal Cove, External Cove, Internal Angles Wall, Floor Junction, etc. set and jointed in approved waterproof chemical Tile adhesive for vertical surface in swimming pools and pointed in epoxy grout to match the shade of tiles over complete all as specified and directed. |
| 13 | M & L for Ceramic Pool tiles for floor 7 to 8 mm thick of low water absorption less than 3.0% and MOR more than 23 N/mm2 incl pool fittings like Internal Cove, External Cove, Internal Angles Wall, Floor Junction, etc. set and jointed in approved waterproof chemical Tile adhesive and pointed in epoxy grout to match the shade of tiles complete all as specified and directed. |
| 14 | Taking down cement plaster on brick or stone walls incl.raking out joints hacking for key scrubbing down with water complete all as specified and directed. |
| 15 | M&L for rendering 15mm thick cement plaster on fair faces of brick or concrete surfaces in cement mortar 1:6, finished even and smooth w/o using extra cement complete all as specified and directed. |
| 16 | M&L for rendering 15mm thick cement plaster on fair faces of brick or concrete surfaces in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 17 | M&L for rendering 5 mm thick in CM 1:3 as on concrete surface of ceilings finished even and smooth without using extra cement complete all as specified and directed . |
| 18 | M&L for preparing newly plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted by mechanical means over 1mm thick wall care putty & a coat of primer to make smooth the undulated surfaces complete all as specified and directed. |
| 19 | M&L for Preparation of new plastered surfaces of walls and applying two coats of exterior emulsion paint over 1 mm thick birla wall care putty & a coat of primer with hand roller complete all as specified and directed. |
| 20 | M & L for preparation of newly plastered surfaces & applying two coats of distemper on ceilings complete all as specified and directed. |
| 21 | M&L for complete removal of existing treatment of old plastered surfaces of walls and applying two coats of exterior acrylic emulsion paint over a coat of putty and primer with hand roller/ by mechanical means complete all as specified and directed. |
| 22 | M&L for complete removal of existing treatment of old plastered surfaces of walls and applying two coats of distemper oil emulsion white or tinted with hand roller/ by mechanical means over a coat of putty and primer complete all as specified and directed. |
| 23 | M&L for complete removal of existing treatment of old plastered surfaces of ceileings and applying two coats of distemper oil emulsion white or tinted with hand roller/ by mechanical means complete all as specified and directed. |
| 24 | Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. |
| 25 | Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. |
| 26 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note :- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. |
| 27 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: stainless steel butt hinges and necessary S S screws shall be paid separately. |
| 28 | S&F stainless steel Butt hinges, medium weight and fixed 125 mm complete all as specified and directed |
| 29 | S&F 250 mm long stainless steel sliding bolt complete all as specified and directed. |
| 30 | S&F 150 mm long Stainless steel barrel tower bolt of extruded section complete all as specified and directed. |
| 31 | S&F stainless steel handles cast type anodised 150 mm size complete all as specified and directed. |
| 32 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket complete all as specified and directed. |
| 33 | Supply and fixing powder coated anodised aluminium window and ventilator shutters, side hung type without sash, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium fittings such as peg stays 150mm long 1 No, hinges type B-21, 100mm long (2 No) suitable handle 1 No complete all as specified and directed. |
| 34 | S& F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed. |
| 35 | S & F Stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 36 | S & F 5.0mm thick plain sheet glass ordinary quality to aluminium door/ window in sqaures not exc 0.5 sqm in each pane complete all as specified and directed by EIC. |
| 37 | S & F in repair 5.0mm thick frosted glass ordinary quality to steel window/ventilator in sqaures not exc 0.5 sqm in each pane with wooden beading complete all as specified and directed. |
| 38 | S & F 1000 Ltrs capacity rotational moulded polyethylene water storage tanks white in colour and three layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc incl dismantling of old existing tank complete all as specified in SSR Part I, complete all as specified and directed. |
| 39 | S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod &high density plastic bal screwed for iron pipe 20/25/40 mm dia and fixed (Minimum Weight 210 gms) complete all as specified and directed. |
| 40 | S&F in repair stop valve cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe 25 mm bore or union and fixed complete all as specified and directed. |
| 41 | S&F in repair angle valve cast copper alloy, screwed down high pressure, with quarter turn handle, screwed both ends for iron pipe 15 mm bore or union and fixed complete all as specified and directed. |
| 42 | S&F GI tubing medium grade with all fitting 15 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor incl taking up or down existing steel tubing complete all as specified and directed |
| 43 | S&F GI tubing medium grade with all fitting 20 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor incl taking up or down existing steel tubing complete all as specified and directed |
| 44 | S&F GI tubing medium grade with all fitting 25 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor incl taking up or down existing steel tubing complete all as specified and directed |
| 45 | S&F in repair vitreous china one piece EWC S trap snow white size 640mm x350mm x725 mm including cistern and seat cover complete all as specified and directed. |
| 46 | S&F in repair 15 mm bore bib cock, two way, cast copper alloy chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as directed. |
| 47 | S&F in repair cromium plated brass health faucet with 8mm dia 1.00m long flexible tube and wall hook complete all as directed. |
| 48 | S&F in repair Toilet paper roll holder with flap Vitreous china with CP brass screw complete all as specified and directed. |
| 49 | S & F in repair vitreous china wash basin, white flat back size 445 x 445x135 mm excluding taps, waste chain and plug and porcelain stopper but including brackets, CP coupling complete all as specified and directed. |
| 50 | S&F in repair SS bottle trap of 32mm bore with 300mm long wall connection pipes complete all as specified and directed. |
| 51 | S & F in repair 15 mm bore Pillar cock long body with swan neck spout and aerator complete all as specified and directed. |
| 52 | S& F Shower rose 300 mm long of square shape 150 mmx150 mm complete all as specified and directed. |
| 53 | S&F in repair vitreous China urinals with integrated Efs technology , half stall long body type(back or corner wall type) of size 360 x 330 x 740 mm complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, including waste pipe and couplings complete all as specified and directed. |
| 54 | S&F PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed. |
| 55 | S&F in repair soap dish, stainless steel, approx size 160x160x90 mm complete all as specified and directed. |
| 56 | S&F 1800mm x 750 mm bevelled edge mirror 5mm thick of selected quality glass mounded on 6 mm thick AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washer with aluminium channel of suitable section alround all as specified and directed |
| 57 | S&F in repairs 15 mm bore bib tap fancy type chromium plated cast copper alloy with cruth or butter fly handle screwed down, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. |
| 58 | Dismantling of PVC/ AC and cast iron drain pipes 75/110mm dia, jointed in cement mortar and taking out of trenches if required complete all as specified and directed. |
| 59 | S&F PVC (SWR) pipe single socketed, any in length with rubber ring joints laid in trenches or in floors type 'B' ISI marked of 75mm bore complete all as specified and directed. |
| 60 | S&F PVC (SWR) pipe single socketed, any in length with rubber ring joints laid in trenches or in floors type 'B' ISI marked of 110mm bore complete all as specified and directed. |
| 61 | S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, type type 'B' ISI marked of 75mm bore complete all as specified and directed. |
| 62 | S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, type type 'B' ISI marked of 110mm bore complete all as specified and directed. |
| 63 | M&L concrete bed to dain pipes 75 mm to 100mm dia cement concrete 1:3:6, type C-2 including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 64 | S&F PVC (SWR) bends of any radius 75mm bore complete all as specified and directed. |
| 65 | S&F PVC (SWR) bends of any radius 110mm bore complete all as specified and directed. |
| 66 | S&F PVC (SWR) junction single (single T) equal or unequal 75mm complete all as specified and directed. |
| 67 | S&F PVC (SWR) junction single (single T) equal or unequal 110mm complete all as specified and directed. |
| 68 | S&F PVC (SWR) vent cowl 75mm complete all as specified and directed. |
| 69 | S&F PVC (SWR) vent cowl 110mm complete all as specified and directed. |
| 70 | M & L for PVC (SWR) floor trap, plain with SS grating incl jointing with solvent cement complete all as specified and directed. |
| 71 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for etc (reinforcement cut as required to facilitate demolition) complete all as specified and directed. |
| 72 | M&L for providing precast cement concrete, type B1, 1:2:4 (20 mm graded aggregate ) set in cement mortar 1:4 in landing, cover slabs (for manholes etc.) chullah hoods,chajjas,water troughs, mangers,shelves and similar articles with plain faces including chamfers, weathering, throating etc complete all as specified and directed |
| 73 | M&L for reinforcement cement concrete (Nominal mix) type A1, 1:11/2:3 (20mm graded aggregate) as in slab support on walls, landing, balconies, deck slabs and in shelves and the like complete all as specified and directed. |
| 74 | M&L for use and waste of formwork to sides and soffits of suspended slabs such as roof slab, floor slabs landing horizontal or slopping and similar workks thikness n.exc 200mm including neccesarry sufficient supports etc for flat and rough finished surfaces of concrete etc complete all as specified and directed by Engineer-in-Charge. |
| 75 | M & L for use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20 cm wide complete all as specified and as directed. |
| 76 | M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape requried, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 77 | M&L for 15-16mm thick granite work (table rubbed & polished) (Rajasthan black) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & incl 15 mm screed thick in CM 1:4 complete all as specified and directed . |
| 78 | M& L for Rounding to edges of granite or stones slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed. |
| 79 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 80 | Demolition wall and ceiling boards (fibre pulp, insulation etc) or insulation board/ slabs/ blankets, any thickness including cover fillets complete all as specified and directed. |
| 81 | M&L in repair 19mm thick both side decorative laminates in kitchen cabinets door shutter, cub boards, lockers etc in coloured, complete all as specified and directed by EIC. |
| 82 | S&F continuous (piano) hinges, width of flaps 30mm, brass bright finished complete all as specified and directed. |
| 83 | S&F 40mm dia, cupboard knobs of Brass fixed with nut, screw and washer of mild steel, bright polished complete all as specified and directed. |
| 84 | S&F Multipurpose round Godrej lock for cupboard/drawer round type complete all as specified and directed. |
| 85 | Complete removal of existing roof treatment and properly cleaning the surfaces to remove loose particles with wire brushes complete all as specified and as directed. |
| 86 | M&L padding in PCC 1:2:4 type B-0 (using 12.5mm size graded stone aggregates) laid to average consolidated thickness of 30 mm to provide a proper slope of the RCC slab finished even and smoth without using extra cement complete all as specified and directed. |
| 87 | M&L for applying fibre reinforced, single component, elastomeric liquid applied water proofing membrane in white colour, Excellent in UV having Solar Reflective Index more than 105, with PU hybrid polymers and reinforcing acrylic fibers, % elongation greater than 300 and applied in three layer per litre complete all as specified and directed as follows :- (a) Surface shall be cleaned and moist that no loose particle is left on surface then apply first coat of liquid water proofinfg as a primer on the surface diluting as per manufacture instruction and allow the surface to dry for min 10-12 Hr time period. (b) Apply Second coat of Liquid water proofing without dilution on the primed surface and allow time to dry the surface for min 10-12 hr. (c) Apply Third coat of liquid water proofing without dilution over the second coat and Allow minimum 48 hours before subjecting the painted surface to service. |
| 88 | M&L for Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete and cleaning of the floor complete all as specified and directed. |
| 89 | Taking down carefully the existing aluminium/copper point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets, ceiling rose, fan regulators, lamp holders, call bell, bell pushes any type etc by unscrewing and taken away from site complete and make good the disturbed surface as existing. Note :(i) cost of unserviceable materials will be charged from the contractor against schedule of credit. (ii) Serviceable light fitting shall be kept in safe custody for reuse at site. (iii) Re-fixing shall be measured and paid seperately. |
| 90 | Taking down unserviceable submain wiring any size,complete all as specified and directed. |
| 91 | M&L for point wiring with 1.5 sqmm PVC insulated FRLS sheathed 1100 Volts grade copper multi stranded conductor drawn through and including rigid PVC conduit 20 mm dia concealed in walls ,roofs, etc including 1.5 sqmm PVC insulated copper conductor as earth continuity conductor and other accesories such as metal box, sheet cover, screws,nuts etc connecting it to the common earth dolly all as specified for one light/ceiling fan/Exhaust fan / wall fan each controller by one way switch |
| 92 | Description all as per item no 90.00 above but one 3 pin 5 Amps socket outlet on same board controlled by one switch. |
| 93 | Description all as per item no 90.00 above but with 2.5 sqmm cable copper for 6 Amps socket outlet on independent board,including 2.5 sqmm copper conductor PVC insulated sheathed continuous earth wire and connecting to common earth dolly. |
| 94 | Description all as per item no 90.00 above but with 4.0 sqmm cable copper for 15/16 Amps socket outlet on independent board,including 4.0 sqmm copper conductor PVC insulated sheathed continuous earth wire and connecting to common earth dolly ( for AC/ Water heater/ water cooler) |
| 95 | M & L Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed as required in PVC Conduit conceiled type 2x6.0 sq. mm + 1x6.0 sq. mm for earth wire all as specified and directed |
| 96 | Supply and fixing LED batten 20 Watt extruded housing, high power diffuser, slim and integrated design, lumen not less than 2100 lumen, energy efficient fixed to wall/ ceilling and connecting upto ceilling rose with three core twisted flexible 1.5 sqmm PVC copper conductor cable with earthing, wire should be passed through flexible PVC cover complete all as specified and as directed. |
| 97 | Supply and fixing LED batten 10 Watt extruded aluminium housing,high power diffuser, slim and integrated design, lumen not less than 2100 lumen polycarbonate, energy efficient fixed to wall/ ceilling and connecting upto ceilling rose with three core twisted flexible 1.5 sqmm PVC copper conductor cable with earthing, wire should be passed through flexible PVC cover complete all as specified and as directed. |
| 98 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. |
| 99 | M & L Switch Modular type single pole, one way 6 Amp complete all as specified and directed. |
| 100 | M & L Modular Socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed. |
| 101 | M & L Modular Switch socket combination outlet 3 pin 6 amp combined 3 module complete all as specified and directed. |
| 102 | M & L modular Switch socket combination multipurpose 3 pin, 16 amp and one pin, 6 amp controlled by one switch 3 module complete all as specified and directed. |
| 103 | S & F Modular Fan step regulator, 120W - 1/2 module complete all as specified and directed. |
| 104 | S & F ceiling rose 3 terminal PVC/polycarbonate isolated body type complete all as specified and directed. |
| 105 | Supply and fixing SP 6-32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 106 | Supply and fixing SPN 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 107 | Supply and fixing SPN 40-63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 108 | Supply and fixing MCCB 4P 125 Amp rating 415V, 16 KA in DB complete with connection testing and commissioning complete all as specified and directed. |
| 109 | Supply and fixing 2 way SPN with bus bar for flood light complete all as specified and directed. |
| 110 | Supply and fixing 8 way SPN Double door DB with 200 amps rated bus bar complete all as specified and directed. |
| 111 | Supply and fix 12 way TPN Double door DB with 200 amps rated bus bar complete all as specified and directed. |
| 112 | M & L Flush type AC starter 6 M with DP MCB and plug top with indicator complete all as specified and directed. |
| 113 | Supply and fixing blank plate of 1 module for switch and mcbs complete all as specified and directed. |
| 114 | Taking down ceiling fan/ exhaust fan/ wall fan, cealing cable end, dismantling blades and removing fan and blades Complete all as specified and directed. |
| 115 | Servicing of ceiling fan/exhaust fan incl open all parts, lubrication, cleaning, rewinding and other necessary job to make smooth run of the item Complete all as specified and directed. |
| 116 | M & L for Spray Painting of ceiling/ wall fans and Exhaust fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed. |
| 117 | Re-Hanging ceiling fan (M.D. supply), serviceable light fitting and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed. |
| 118 | Re-Fixing only exhaust fan (M.D. supply) and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified and directed. |
| 119 | Re-Fixing only LED batten, MCBs, LED lights which are obtained from items No 01 and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified and directed. |
| 120 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1400 mm sweep. Min air delivery 245 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 121 | Supply and fixing exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed by Engr-In-Charge. |
| 122 | Supply & fixing heavy duty wall mounted industrial turbo fan of metal body of 600 mm , 1440 RPM by help of nuts, bolts, screw complete all as specified and directed. |
| 123 | S & F Earthing complete with Galvanised steel earth plate electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of plate not less than 1.50 m below normal ground level connected to 25 X 3 mm GI Strip [Earth Lead] and GI pipe 50 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the plate by means of GI Bolts & Nuts complete all as per Electrical plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. complete all as specified and directed. |
| 124 | Labour for taking down flood light and held in store and refixing the same after completion of work in proper manner as per existing including nuts, bolts, fastner, long length brackets, aluminium strip for fixing brackets with wall complete all as specified and directed. |
| 125 | Supply and fixing of PVC sheathed multi stranded copper conductor cable of size 2.5 sqmm 3 core from switch board to LED light connection and cable should be pass through PVC conduit/ caping casing and fixed by heavy saddle apar 60 cm each complete all as specified and directed. (For flood light & building security light) |
| 126 | Supply and fixing MS ERW heavy grade pipe of 25 mm bore including fabrication, welding, grinding etc including taking down old unsv complete all as specified and directed. |
| 127 | Supply and fixing MS ERW heavy grade pipe of 80 mm bore including fabrication, welding, grinding etc including taking down old unsv complete all as specified and directed. |
| 128 | Supply and fixing MS ERW heavy grade pipe of 150 mm bore including fabrication, welding, grinding etc including taking down old unsv complete all as specified and directed. |
| 129 | Supply and fixing MS ERW pipe of 200 mm bore, 6.0 mm thickness including fabrication, welding, grinding etc including taking down old unsv complete all as specified and directed. |
| 130 | Supply and fixing MS ERW pipe of 250 mm bore, 6.0 mm thickness including fabrication, welding, grinding etc including taking down old unsv complete all as specified and directed. |
| 131 | Supply and fixing MS ERW pipe of 300 mm bore, 6.0 mm thickness including fabrication, welding, grinding etc including taking down old unsv complete all as specified and directed. |
| 132 | Supply and fixing MS fittings upto 300 mm bore pipe i.e long/short elbow, flanges, blank flanged, reducer, jointer, T joint, MS angle iron , MS sheet, MS frame etc complete all as specified and directed. |
| 133 | S & F CI foot valve of size 150 mm with gun metal working parts, ISI marked with all fittings i.e flanged, nuts, bollts, washer, welding, grinding incl taking down old unsv complete all as specified and directed by EIC |
| 134 | M & L for Dual plate check 150 mm bore PN1.6 of undermentioned type and size with cast iron body, double Disc of CS, Hinge pin, plate bearing, plugs of SS 410 and spring of SS316 and both ends flanged, ISI marked comlete with neoprene rubber gasket ,jointing material, connected with existing MS pipe by jointing through flanged and welding work, rubber gasket, nuts/bolts/washer of suitable size etc complete all as specified and directed |
| 135 | S&F for non return valves, class PN 1.6 of 150 mm size with cast iron body and both ends flanged, IS-14846 marked comlpete with neoprene rubber gasket, jointing material and incl nuts/bolts/washer of suitable size, welding, grinding, flanged etc including taking down old unsv complete all as specified and directed . |
| 136 | M & L for Pipe Support for all types of pipes including hangars / fastners / MS strips/ GI strips/ MS angles/ supports and taking down unsv complete all as specified and directed. |
| 137 | S&F in replacement for sluice valves, class PN 1.6 of 80mm bore size with cast iron body, non rising type and cast iron wheel head, both ends flanged, IS-14846 marked comlete with neoprene rubber gasket, jointing material and incl nuts / bolts / washer of suitable size, welding, grinding, flanged etc complete all as specified and directed. |
| 138 | S&F sluice valves, class PN 1.6 of 150mm bore size with cast iron body, non rising type and cast iron wheel head, both ends flanged, IS-14846 marked comlete with neoprene rubber gasket, jointing material and incl nuts / bolts / washer of suitable size, welding, grinding, flanged etc including taking down old unsv complete all as specified and directed. |
| 139 | M & L for Butterfly valve 80 mm dia, ISI marked complete with all fittings/accessories, nutts, bolts, washer, flanged, welding, grinding required for fixing in MS pipe of filter plant including taking down old unsv complete all as specified and directed. |
| 140 | M & L for Butterfly valve 200 mm dia, ISI marked complete with all fittings/accessories, nutts, bolts, washer, flanged, welding, grinding required for fixing in MS pipe of filter plant including taking down old unsv complete all as specified and directed. |
| 141 | M&L for water high pressure gauge including socket welded to measure pressure in the delivery pipe 0-300 Psi and taking down old unsv complete all as specified and directed. |
| 142 | M& L for boring for fixing the MS pipe upto 300 mm bore below hard standing for changing of existting rusted pipe in swimming pool area complete all as specified and direced. |
| 143 | Labour for taking out of old unsv filter media from 03 Nos filteration plant of size 3.0 mr X 2.0 mtr and thrown the material out from mil stn as per direction of Engg in charge complete all as specified and directed. |
| 144 | Labour for fixing of filter media/ sand gravels in 03 Nos filteration plant of size 3.0 mr X 2.0 mtr as per existing and black bituminious paint in side wall of filteration as per direction of Engg in charge complete all as specified and directed. |
| 145 | Supply only sand gravells of size 4-8 mm, 8-10 mm, 10-12 mm, 18-22 mm & 40-50 mm for filteration plant complete all as specified and directed. |
| 146 | M & L for preparation of old painted steel surface of centrifugal pump with motor and base of 30 HP -03 Nos, Various sizes MS pipes wih valves of 80 mm to 300 mm upto 180 mtr long, filteration plant of size 3 mtr X 2 mtr - 03 Nos, suction sweeper pump with rolley - 02 Nos and applying two coats of synthetic enameled paint over applying one coat of red oxide primer by spray machine with good finish, maitain color code and also mark the direction of flow and write the filteration cap, washout water, filteration water etc as per existing is specified by Engg in charge complete all as specified and directed. |
| 147 | Supply, fixing and testing 3 HP suction sweeper with pump, motor, MS material witth trolley mounted with wheels for easily to operatation with suitable size flexible pipe of 50 mtr long for drain out the water from swimming pool, heavy duty and heavy dead weighted steel vacuum head with brush of 24 inch and roller for move, suitable size and length wire rope for vacuum head, DOL starter and 2.5 sqmm copper cable of 50 mtr long complete all as specified and directed. |
| 148 | Excavation in trenches in any type of soil not exceeding 1.5m wide and not exceeding 1.50m in depth and getting out complete all as specified and directed by Engr-in-Charge. |
| 149 | Returning, filling in soil including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed by Engr-in-Charge. |
| 150 | Removing surplus excavated spoil(soil) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engr-in-Charge. |
| 151 | Sand cushioning to under ground cables 8cm thick before laying the cable and 15cm thick after laying, stretching and testing the cable complete all as specified and as directed. |
| 152 | Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1 with peak, size 250mm x 150mm x 40mm along length of cable in trenches after sand cushioning laid for underground cable protection complete all as specified and as directed |
| 153 | M&L for galvanised steel tubing, 'light grade' galvanised, with all fitting and fixed in wall/chases and in trenches for cable protection/earth lead protection complete 80 mm bore. |
| 154 | Supply and laying cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95.0 sq mm 3.5 core (Existing 2 pole structure LT Panel to building LT panel). |
| 155 | Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70.0 sq mm 3.5 core ( building LT panel TPN DB). |
| 156 | Supply and laying cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 4 core ( building LT panel to High mast). |
| 157 | Supply and laying cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0 sq mm 4 core (building LT panel to garden light). |
| 158 | Supply & fixing of 10 W decorative inverted tripod type LED Bollard with IP 65/66 protection soft 360 degree light distribution. Body made of die cast aluminium and in triangular shape with IP65 ingress protection and 4KV surge protection and grouted at PCC foundation with necessary nuts and bolts complete all as specified and directed by Engr-in-Charge. |
| 159 | Supply and fixing LED flood light 210 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp and flood light fixed at high mast complete all as specified and directed by Engr-in-Charge. |
| 160 | Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including brackes, GI pipe, nuts, bolts and taking down old unsv complete. |
| 161 | S & F Rigid non-metallic PVC conduit of size 40mm dia having wall thickness not less than 2mm exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. for cable protection and laying in tranches complete all as specified and directed by Engr-in-Charge. |
| 162 | M&L for PCC 1:2:4 Type B-2 (using 40mm graded crushed stone aggregate) as in foundation ,filings and mass concrete, road cutting complete all as specified and directed by Engr-in-Charge. |
| 163 | S&F outdoor Canopy type weather proof IP 54 LT panel board front opening hinged typed, double door with locking arrangement, made out of 3.15 mm thick CRCA sheet steel factory fabricated with powder coating with heat shrinkable PVC sleeves with colour code RYBN placed on insulators. The Aluminium bar RYBN having capacity is 2.0 times of main incomer MCCBs. The panel board shall be mounted 60 cm above ground level on a form work made out of MS channel of size 75 x 40 cm grouted on PCC Plateform. The sides of the form work shall be covered with 3.15 mm thick MS sheet and complete with necessary excavation PCC foundation, suitable cable glands for cable entry, cable lugs etc.The panel board shall be suitable housed with the following items:-(i) 4 Pole MCCB 200 Amp with rupturing capacity 25 KA (Main Incoming)-1 Nos(ii) 4 Pole MCCB 125 Amp with rupturing capacity 16 KA (Outgoing)- 1 Nos (iii) 4 Pole MCCB 63 Amp with rupturing capacity 16 KA (Outgoing)- 3 Nos (iv) 4 Pole MCCB 40 Amp with rupturing capacity 16 KA (Outgoing)- 2 Nos (v) 4 Pole MCCB 25 Amp with rupturing capacity 16 KA (Outgoing)- 2 Nos (iv) Volt meter 0-500 volts with selector switch (v) Amp meter 0-300 Amp with selector switch (vi) Phase indicator lamps LED type set of three (RYB) - 01 Set (vii) Street light timer for gardening light, building security light, high mast light - 02 Nos Note : Drawing, wire layout and BoQ should be submitted to department for Approval of GE before procurement. |
| 164 | S & F 15 mtr long High galvanized mast light suitable for 8 lantern symmetrically fitted along with their control gear and having two point suspension system with stainless steel wire rope of 6 mm dia 7/19 guage and double drum winch with luminaire mounting arm, pully assembly, aviation obstruction light, lightning arrester spike, foundation bolts, nuts, plates, trailing cable & integral power tool for raising and lowering operation of high mast with including RCC foundation as per height as per OEm recommendation, outdoor powder coated CRCA sheet Feeder pillar for high mast as per OEM recommendation etc. complete all as specified and directed. Note : Drawing of high mast and foundation as per OEM recommendation should be submitted to department for Approval of GE before procurement/ execution. |
| 165 | Schedule of Credit Total in Figures 0.0 0.0 -92041.0 Quoted Rate in Figures Select 0.0 0.0 Zero Only 0.0 Quoted Rate in Words INR Minus Ninety Two Thousand &Forty One Only Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysNov 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender