Tender For Special Repair To Building No. Ht-31 (Or Living Area) Of Ad Msl Regt Wksp Under Ge (South) Ambala Cantt
Tender Value
63.23 Lakhs
Estimated cost
Bid Submission
30 Nov 2026
26 days left
EMD
1.19 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ambala → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Building No. Ht-31 (Or Living Area) Of Ad Msl Regt Wksp Under Ge (South) Ambala Cantt
BOQ
| Sl. No. | Item Description |
| 1 | SCHEDULE 'A' PART-I (BUILDING WORKS):Demolition of brick work built in CM incl all quions arches, pillar etc all as specified and directed. |
| 2 | Material and labour for brick work with flyash bricks of class designation 75, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified & directed |
| 3 | Material & labour for flyash Brickwork having class designation 75, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 etc complete all as specified and directed . |
| 4 | Taking down Cement plaster on brick or stone walls incl raking out joints hacking for key & scrubbing down with water etc complete all as specified and directed. |
| 5 | Material & labour for Rendering 15 mm thick on surface of any description of brick work or concrete surfaces, finished even and fair (without using extra cement) on walls in cement mortar (1:6), complete all as specified and directed . |
| 6 | Material & labour for rendering 15mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), using water proofing compound complete all as specified and directed . NOTE:WPC will be measured and paid for separately. |
| 7 | Material & labour for rough cast plastering over and incl 10 mm thick rendering in cement mortar 1:3 and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered. Rough cast plaster shall be applied as specified clause 14.22 of SSR Part-I . |
| 8 | Supply only integral water proofing comound ISI Marked complete all as specified and directed. |
| 9 | Material & labour for preparation of new plastered surface of walls & applicataion of two coats of 100% premium acrylic emulsion paint with fully automatic airless spray machine & paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance , dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @1.43 lit/10 sqm over & including priming coat of exterior primer applied @2.20kg/10 Sqm complete all as specified & directed |
| 10 | Material & labour for preparation of old plastered surface of walls including removal of existing treatment by mechanical dry wall sander machine & applicataion of two coats of 100% premium acrylic emulsion paint with fully automatic airless spray machine & paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance , dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @1.43 lit/10 sqm over & including priming coat of exterior primer applied @2.20kg/10 Sqm complete all as specified & directed |
| 11 | Material & labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with fully automatic airless spray machine ,over a coat of alkaline resistant primer & a coat of birla wall care putty surface having minimum thickness 1.50mm complete all as specified and directed. |
| 12 | Material and labour for complete removal of existing treatment on surface of walls by using mechanical dry wall sander machine for complete removal of all layers of treatment and reaching upto old plastered surface and applying a coat of wall care putty not less than 1.5mm thick as per manufacture instructions and applying two coats of oil emulsion paint with fully automatic airless spray machine over a coat of alkaline resistant primer complete all as specified and directed. |
| 13 | Dismantling of AC corrugated, semi corrugated sheet including ridges etc. in roof covering complete all as specified and directed. |
| 14 | Dismantling of ceiling boards (fibre, pulp, insulation, etc.) or insulation boards /slabs/ blankets, any thickness, including cover fillets, false ceilings etc complete all as specified and directed. |
| 15 | Material and labour for Roof Trusses (framed) , trussed , purlins, rafter ,crane gantries, rails and fastenings and heavy bracket framing ( Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed. |
| 16 | Supply and fixing for steel work in struts, tubular trusses, stanchions including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 Grade St-240 complete all as specified and directed. |
| 17 | Material and labour for plates (plain and chequered) channels, square cut or notched ( ordinary and counter sunk) forming holes without any attachment of Fe-410W(gde-E-250) quality A complete all as specified and directed. |
| 18 | Supply and fixing for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed. |
| 19 | Supply and fixing for Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall fixed with self tapping screws etc complete all as specified and directed. |
| 20 | Supply and fixing for mild steel sheet 1.25mm thick eaves gutters 150mm diameter, galvanised class 3 half rounded with rounded edges complete all as specified and directed. |
| 21 | Supply and fixing for angles (internal or external) or nozzle pieces outlet of 150mm dia & 1.25mm thick galvanised sheet complete all as specifed & directed |
| 22 | Supply and fixing for stop ends of 150mm dia & 1.25mm thick galvanised sheet complete all as specifed & directed |
| 23 | Supply & fixing for false ceiling with semi perforated 12mm thick micro tegular edged GRG false ceiling tiles at all heights with glass fibre reinforced gypsum false ceiling tiles of size 595x595 mm of approved texture, design & patterns having moisture content less than 2%, humidity resistance of 99% , NRCO 0.50 to 0.75 as per IS 8225:1987, noncombustible as per BS 476 (part 4)- 1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @120 gms per sqm on both sides) comprising of main T runners of size 15x32mm of length 3000mm, cross T of size 15x32mm of length 1200mm & secondary intermediate cross T of size 15x32mm of length 600mm to form grid module of size 600x600mm , suspended from ceiling using galvanised mild steel item (galvanising @ 80 grms per sqm) ie 50mm long , 8mm outer dia M-6 dash fasterners or 4mm galvanised hook , 4mm dia galvanised wire for hanging upto 1000mm length and L shape level adjuster of size 85x25x2mm . Galvanised iron perimeter wall angle of size 24x24x0.4mm of length 3000mm to be fixed on periphery wall /partition with the help of plastic rawl plugs at 450mm centre to centre & 40mm long dry wall wood screws complete all as specified and directed. |
| 24 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as specified and directed. |
| 25 | Demolition of Cement Concrete as in G.F & paving n. exc. 15cm thick (above or below ground level) complete all as specified and directed. |
| 26 | Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar complete all as specified and directed. |
| 27 | Material and labour for 50 mm thick PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in plinth protection finished fair and even smooth without using extra cement complete all as specified and directed. Note:- The plinth protection shall be laid in panels and length of each panel shall not be more than 2.00 m all as directed 6mm joints filled with 85/25 grade bitumen and sand in the ratio (1:3) shall be provided. |
| 28 | Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 8 to 9 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or layer in cement mortar (1:4) complete all as specified and directed. |
| 29 | Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 8 to 9 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed. |
| 30 | Material and labour for premium quality coloured glazed ceramic tiles (350 x 250 x 7 mm thick / 450 x 300 x 7 mm thick) and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match including rendering 10 mm thick in cement plaster 1:4 as in vertical surfaces complete all as specified and directed. |
| 31 | Material and labour for 18 to 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in 15mm thick cement mortar (1:4) and jointed with grey cement slurry @ 3 Kg/Sqm, and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding, polishing, rounding and moulding of stone slabs on edges, complete all as specified and directed. |
| 32 | Taking down chowkaths or frames exc 1.5 sqm but n exc 4.0 Sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc complete all as specified and directed. |
| 33 | Supply and fixing for mild steel 300 mm, helical door spring with roller plate for door shutter including welding if necessary fixed in repair complete all as specified and directed. |
| 34 | Supply and fixing for floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 150mm complete all as specified and as directed. |
| 35 | Supply and fixing for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 125 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made. |
| 36 | Supply & fixing for stainless steel butt hinges 100 mm long medium weight complete all as specified & directed. |
| 37 | Supply & fixing for factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) complete all as specified and directed. Note: Material Test Certificate & Authentication should be provided by the manufacturing company. |
| 38 | Supply & fixing for 30 mm thick Factory Made 100% Solid WPC ( Wood polymer Composite ) gauzed and skeleton Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ),alcium Carbonate andnatural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheetSingle Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured and an ISO 9001 -2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 Modulus of elasticity 850N/mm2and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. rate inslusive for Fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws incl Aluminum Jali and Stainless wiremess as per required. complete all as specified and directed. Material test certificate and authentication should be compulsory provided by the manufacturing company |
| 39 | Supply & fixing for aluminium anodised extruded fabricated type handle 150 mm long complete all as specified & directed. |
| 40 | Supply & fixing for 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified & directed. |
| 41 | Supply & fixing for aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing with bolts extruded sections complete all as specified & directed. |
| 42 | Supply & fixing for of windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2 Nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work including of all taxes. |
| 43 | Material & labour for painting to steel surfaces of any description not other wise described over 10cm width or girth with two coats of synthetic enamel paint over one coat of red oxide primer incl preparation of new surfaces complete all as specified and directed. |
| 44 | Material & labour for preparation of old steel surface & painting to steel surfaces of any description not other wise described over 10cm width or girth with one coat of synthetic enamel paint complete all as specified & as directed |
| 45 | Supply & fixing in repair of 4.0mm dia plain mild steel wire galvanised class 3 for hanging arrangement for mosquito net ,including securing hanging including straining and fixing to wood ,concrete or steel hooks to or with straining bolts including necessary arrangement as per site requirement complete all as specified and directed.(Each line of wire to be measured). |
| 46 | Supply & fixing for stainless steel curtain rod 25mm dia having wall thickness 1.6mm fixed with and including stainless steel decorative brackets, two lotto for each road length at both end etc as in repair complete all as specified and directed. |
| 47 | Supply & fixing for in repair SS peg set of 5 size 300x20x2.5mm complete all as specified and directed. |
| 48 | Excavating in post holes (or similar holes) each n.exc 0.50 Cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in any type of soil complete all as specified and directed. |
| 49 | Material and Labour for PCC (1:3:6) type C2 by using 40 mm well graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed. |
| 50 | Supply & fixing for mild steel TMT bar 10mm dia and over cut to length bent to shape required, including cranking bending spirally and binding with and including mild steel sire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 51 | Demolition of RCC n exc 15cm thick in any position complete all as specified & directed |
| 52 | Material and Labour for RCC (Nominal Mix) type B-0 1:2:4 (using 12.5 mm graded aggregate) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 53 | Material and Labour for machine cut kota stone slab flooring 20-25mm thick over cement screed bed CM 1:6 15mm thick, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed. |
| 54 | Material and Labour for 75mm thick PCC type D-2 , (1:4:8) using 40mm graded stone aggregates as in subbse complete all as specified & as directed |
| 55 | Material and Labour for machine pressed precast concrete interlocking paver block with grey cement & no pigment, any shape & size conforming to IS 15658-2006 of 60mm thickness M-35 grade complete all as specified & as directed |
| 56 | Material and Labour for 25mm thick sand filling under floors including watering & consolidation complete all as specified & as directed |
| 57 | Supply & laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level & curvature , jointed with cement mortar 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening whereever required complete all as specified and as directed |
| 58 | Supply and Fixing in repair prepainted (of approved colour) 18 gauze thick MS sheet shutter fixed with necessary hinge support, 7 lever lock with three keys, SS handle 200 mm length including locking bar arrangement complete all as specified & as directed |
| 59 | Formwork to soffit of suspended slabs such as roof slabs, floor slabs, landings,and similar work not exceeding 200mm thick complete all as specified and as directed |
| 60 | Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings, in concrete walls, floor & roofs exc 5cm but not exc 10cm wide complete all as specified & as directed |
| 61 | Dismantling structural steel work including doors, gates etc complete all as specified and as directed |
| 62 | Supply and Fixing in repair 4mm sheet glass, ordinary quality and glazing with oil putty in opening n. exc 0.5 Sqm in each pane complete all as specified & as directed |
| 63 | Supply and Fixing in repair galvanised mild steel wire cloth,0.63mm nominal dia of wire & average width of aperture 1.40mm & fixed with tinned tacks or galvanised wire staples complete all as specified and as directed |
| 64 | Material and Labour for cement concrete Type D-2 , 1:4:8 , 100 mm thick in subbase floor complete all as specified & as directed |
| 65 | Material and Labour for PCC 1:2: 4 type-B1 as in sub base to floor 25 mm thick using 20mm graded aggregate complete all as specified & directed |
| 66 | Supply and fixing of steel plate including mention on Bar Code, letter writing not exc 10 cm Height each word any discription not exc. 200 words total fixed on brick work/ concrete work etc with steelness steel screwed complete all as specified & directed. |
| 67 | SCHEDULE 'A' PART-II (INTERNAL ELECTRIFICATION WORKS):Taking down carefully aluminium/ copper point wiring (light, fan,socket or power) complete, including fixtures and fittings such as switches, ceiling rosees, pendants, regulators , sockets, light fittings etc., removing materials to stores for keeping in safe custody for taking credit and making good the disturbed surfaces of walls,ceilings etc. |
| 68 | Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed/surface type on wall/ceiling and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including GI/Pressed steel terminal boxes suitable for modular covered plate over sunken box for housing the modular switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for the following :- (a) Metal flush/sunken Box, modular switch/socket cover plate & sheet are inclusive in the item rate quoted. (b) Only switches, socketes and fan regulators to be measured and paid seperately. |
| 69 | Description all as per item No 68 here in before but for socket out let point 6 Amps on same board |
| 70 | Description all as per item No 68 here in before but for socket out let point 6 Amps on independent board |
| 71 | All as per srl item No 68 above but point wiring for one socket out let 16 & 6 Amps (independent) controlled by one switch with using 2.5 Sq mm (nominal area) stranded copper conductor |
| 72 | Supply and fixing for ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified. |
| 73 | Supply and fixing for modular switches, one way, 6 amps one module, 230V, 50 Hz supply, complete all as specified and directed. |
| 74 | Supply and fixing for modular switches, one way, 16/20 Amps, one module, 230 volt , AC supply, complete all as specified and directed. |
| 75 | Supply and fix for modular socket outlet 6 amps, 2/3 pin combined 2 module, 230 volt, complete all as specified and directed. |
| 76 | Supply and fix for modular socket outlet 16/20 amps,3 pin, 2 module, complete all as specified and directed. |
| 77 | Supply and fix for modular fan regulator step type one module / 2 module, 100 W, 230 Volts, 50 Hz, AC complete all as specified and directed. |
| 78 | Supply and fixing for LED luminaries of capacity 20 watt integrated aluminium batten with including Oppel diffuser,PF not less than 0.9,lumen efficacy not less than 100 lumen/Watt,marked with relevent IS complete including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and as directed. |
| 79 | Supply and fixing in repair Bulk Head Fitting 10 Watt and connected with copper conductor cable of size 1.50 Sqmm, for fixing the light fitting complete all as specified & directed. |
| 80 | Supply and fixing for recess/ surface mounted LED flat panel 2' x 2' with high efficient LEDs and glare free full decorative light fitting, energy efficient provided with including LED 36 watt, Cool White / Warm White, duly marked with relevent IS, PF not less than 0.9,lumen efiicacy not less than 100 lumen/watt with provision of 2/3 core PVC copper conductor cable 1.5 Sqmm size to light fitting and complete including disconnecting and taking down existing light fitting and removal complete all as specified and directed. |
| 81 | Supply and fixing in repair aesthetically designed wall bracket light (Wall Light) metal base in B22 holder with 7 watt LED lamp warm white, compact and energy efficient, epoxy powder coated light luminaire, PF not less than 0.9,lumen efficacy not less than 100 lumen/Watt,marked with relevent IS complete all as specified and as directed. |
| 82 | Supply & fixing for bracket for security light made up of 32 mm dia,suitable for security light,0.6 meter long GI pipe, light grade, 120 degree bent to required length, fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos, 8mm dia bolts with nuts complete all as specified and directed. |
| 83 | Supply & fixing for LED security light luminaire 35 watt , pressure die cast aluminum housing, toughened heat resistant glass, IP66 protection, better optics for uniform distribution with multiplte LEDs not less than 2 W each and having optical grade polycarbonate lens with all accessories internally pre wired and including connecting up with two core 1.5 sq mm copper conductor cable from connector to ceiling rose to connection of light complete all as specified and directed by the Engineer-in-Charge. |
| 84 | Supply & fixing for prewired metal enclosure modular power unit with 20 Amp modular mini MCB and 1x No. power socket with 1xNo 15 Amp 3 pin top plug for Geyser and taking down existing power unit complete all as specified and directed. |
| 85 | Supply & fixing for sheet metal enclosures vertical distribution board VTPN,(MCCB DB) 4 ways, double door , 415 volts with suitable size of rated bus bar IP 54 protection, with shrouded neutral bar and insulated bus bar and earth link, with and including MCCB 4 pole adjustable thermal release type ,125Amps ,25 kA as incomer and MCB s as out going complete with making suitable size of MS cabinet 1.2 mm thick dully grouted on the wall (flush) with opening arrangement including making connections with suitable size of lugs/thimbles and making good the disturbed surface matching with existing surface complete all as specified and directed. |
| 86 | Supply and fixing in repair SPN distibution board 8 way, double door, IP 43, as per IS 8623 including fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles complete all as specified and directed. |
| 87 | Supply and fixing for 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 88 | Supply and fixing for 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 40 to 63 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 89 | Supply and fixing for 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of SP and current carrying capacity 40 to 63 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 90 | Material and labour for sub main wiring with two single core FRLSH, PVC insulated unsheathed copper conductor cable 6.0 sq mm drawn in and including rigid non metallic PVC medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated , stranded copper conductor FRLSH of 6.0 sqmm,green colour for earth continuity conductor including including taking down old unserviceable sub main wiring and making good the disturbed surface complete, all as specified and directed.Note:- Three run of wiring and one run of conduit shall be measured and paid as one lenght only. |
| 91 | Material and labour for sub main wiring with two single core FRLSH, PVC insulated unsheathed copper conductor cable 4.0 Sqmm drawn in and including rigid non metallic PVC medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated , stranded copper conductor FRLSH of 4.0 Sqmm,green colour for earth continuity conductor including including taking down old unserviceable sub main wiring and making good the disturbed surface complete, all as specified and directed .Note:- Three run of wiring and one run of conduit shall be measured and paid as one lenght only. Please Enable Macros to View BoQ information |
| 92 | Material and labour for sub main wiring with two single core FRLSH, PVC insulated unsheathed copper conductor cable 4.0 Sqmm drawn in and including rigid non metallic PVC medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated , stranded copper conductor FRLSH of 4.0 Sqmm,green colour for earth continuity conductor including including taking down old unserviceable sub main wiring and making good the disturbed surface complete, all as specified and directed .Note:- Three run of wiring and one run of conduit shall be measured and paid as one lenght only. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 26 daysDec 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 28 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender