Tender For Repairing Of 02 Nos. Dy Gate At Dy -A Ch-0.00 (Ch 770 Of Lbmc) At Rondia Under Dhw Division, Durgapur During The Year 2026-27
Tender Value
2.45 Lakhs
Estimated cost
Bid Submission
25 Nov 2026
19 days left
EMD
4911
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bankura → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairing Of 02 Nos. Dy Gate At Dy -A Ch-0.00 (Ch 770 Of Lbmc) At Rondia Under Dhw Division, Durgapur During The Year 2026-27
BOQ
| Sl. No. | Item Description |
| 1 | Supplying to site empty cement polythene bags (capacity 50kg) in good condition including stacking, incedental charges etc. all complete (capacity 50 kg). |
| 2 | Dumping in position earth / sand filled gunny / poly bags (capacity 50 kg) within a lead of 30 metre inclusive of all lifts. |
| 3 | Labour charges for filling empty cement gunny bag / polythene bag (capacity 50 kg) with all kinds of earth (wet or dry), sand or agreegates(stone / brick) and sewing as done in case of cement bags ,( tying with a knot after filling will not be accepted ) , and stacking within a lead of 30 metre as per direction of Engr-in-charge (cost is excluding the cost of any types of filling materials).NB:- Volume of earth/ sand filled bags should not be less than 0.028 cum/ bag. |
| 4 | Removing earth/sand filled poly bags/gunny bags from the channel bed/slope and initially depositing the same near channel bank at a place as directed by the Engineer-in Charge for measurement of Bag. & then disposing off the same at a distance not less than 150 metre from the channel site. |
| 5 | Bailing out water by pump including all leads and lifts and including making all arrangement for disposal, where continous flow or seepage of water is encountered and rating of pumps and hours of operation is specifically of ascertained as per direction of Engineer-in-charge. |
| 6 | Surface cleaning of metal surfaces by chemical cleaners and then by hand with emary paper, wire brush and power tool cleaners and removing dust and preparation of surface including cost of all materials, labour, machinery, scaffolding, etc., complete with initial lead for sand upto 1 km and all lifts. |
| 7 | Painting of Gates of Distributory/Branch/Minor canal/ Pump Coloum pipe/Pump Discharge Pipe & other similar components on prepared surfaces with one coats of zinc phosphate primer (airless spray preferred) 50microns/coat and one coal tar epoxy, 150 microns/coat including cost of all materials, labour, scaffolding etc., complete with all leads and all lifts. |
| 8 | Taking out old existing unservicable damaged gate shutter of canal/river completely after disengaging from hoisting system completely for installation of new gate shutter. The work includes cutting of gates into suitable pieces by gas cutting, removing the same by mechanical means or suitable crane, stacking all the pieces at the suitable place or as directed by the Engineer in charge upto a lead of 1000 m. The cost includes cost of man power employed for dismantling and cost of consumables like oxygen, accetylene gas, welding rod, hire charges of machineries, like chain pulley block, gas set, grinding machine, welding set, tools & tackles, scaffolding and safety equipments etc including carriage loading & unloading. The cost of complete dismantling of hoisting system & cost of old unservisable materials handed over to departmental godown including loading & unloading will be provided extra. a) Gate shuteer size upto 4.00 sq.m |
| 9 | Fabrication , Supply, erection and commissioning of new Slide type vertical lift regulator service gates of Distributories /BranchCanal/Minor Canal/Channel as per IS: 5620 - 2000/Latest Revision consisting of skin plate, vertical and horizantal grider, stiffener etc. made of MS material consisting of angle , channel, beam, plate, flat, etc. conforming to IS : 2062 -2011/latest revision manufactured as per approved drawing and direction of Engineer in charge. The Cost includes cost of Materials, Machinaries , Manpower, Cutting,aligning, drilling, Welding, Finishing, Consumables, Carriages and all overheads with all leads and lifts complete as per specification.(without painting). |
| 10 | Cost of transportation for shifting the scrap materials fro site to durgapur Division officew including loading and unloading at both end etc to complete the job at site as per direction of E.I.C |
| 11 | Supplying, fitting & fixing of screw rod having square thread of 1.5/2 T.P.I, Material bright\ steel [EN‐8/EN9/forged Cl‐4 (45C8) as per IS :1875 1992/latest Revision]. dia and thread length as required and providing with a drilled hole of required dia on the other end after flattened and supplying with one no. bolt and nut of required size and all other components as required as per direction of Engineer‐In ‐ Charge. The cost includes cost of material man power employed, consumables like cutting tools, emery paper, cloths, , hire charges of machineries, tools & tackles, grease, mobil etc including carriage loading & unloading as per direction of Engineer in charge.40 ,50 MM DIAa) upto length 3 metre. |
| 12 | Supplying, fitting & fixing M.S fabricated wheel in the screw hoisting system for lifting or lowering the draw shutter.The wheel consisting of suitable size ms hub to accomodate any size of G.M/C.I nut. The rim and four nos arm of wheel are made of 25mm. to 36mm. dia m.s rod complete as per direction of the Engineer‐in‐charge. The cost includes cost of materials,man power employed for dismantling and fitting fixing, consumables like cutting tools,welding rod, hire charges of machineries, like bending machine, lathe machine, grindingmachine welding set, tools & tackles etc including carriage loading & unloading. a) Up to 600mm dia M.S wheel |
| 13 | Supplying, fitting & fixing Gun Metal Nut as per requirement having 1.5/2 T.P.I square thread for screw gearing arrangement, perfectly metting with the screw rod/gear rod for lifting the draw shutter as per direction of E.I.C. The cost includes cost of materials, man power employed, consumables like cutting tools, emery paper, cloths, , hire charges of machineries, tools & tackles etc including carriage loading & unloading. |
| 14 | Supply of thrust bearing (s.K.F) for shaft dia size =50 mm(SKF51111) |
| 15 | Supplying, fitting & fixing of screw hoisting arrangement made of MS bottom plate, top plate, collar with necessary holes on base plate and top plate to accommodate thrust bearing of suitable size as per approved drawing & design and as per direction of Engineer in charge. The cost includes cost of ms plate as per IS : 2062 -2011/ latest revision, man power employed for dismantling and fitting fixing, consumables like cutting tools, bolt & nuts of required size, hire charges of machineries, like lathe/shaping machine, grinding machine, drilling machine, tools & tackles etc including carriage loading & unloading but excluding the cost of lifting Nut/Bush, thrust bearing & wheel supplied separately. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysNov 26, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender