Tender For Restoration Of Bituminous Road From Chemaguri Jetty Ghat To Benuban Car Parking Stand At Sagar For Gangasagar Mela2027 Under Gbda, Dist.- South 24 Parganas.
Tender Value
38.36 Lakhs
Estimated cost
Bid Submission
20 Nov 2026
8 days left
EMD
76728
Bank guarantee accepted
Document Fee
2500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
24 Paraganas South → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Restoration Of Bituminous Road From Chemaguri Jetty Ghat To Benuban Car Parking Stand At Sagar For Gangasagar Mela2027 Under Gbda, Dist.- South 24 Parganas.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of Flexible Pavements Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately (Reference to MoRT&H's specification clause 202)05.(II). By Mechanical Means05.(II).A. Bituminous courses |
| 2 | Bamboo Pile Walling made of 6.5cm to 7.5cm dia bamboo (in single line) driven about half-length into ground at very close spacing of 30cm c/c side by side, with stout stays at an interval of 90cm fixed with bamboo post of length 1.25m driven 1m below G.L., 3 nos. of half split bamboo runner of same dia fitted and fixed with nails etc. and lining exposed portion with sheets made from Darma mat fitted and fixed with a lap width of 100 mm at each joint, complete as per direction including the cost of drum sheets and including the cost of nails, wires etc. (ii) With bamboos of length above 2.00m and upto 2.50m |
| 3 | Eucalyptus bullah walling with earth filled bags 1.30m (av.) high of 10cm. dia and 3.6m long bullah pin @ 0.375 mtr. c/c bullah walling of 2.7m (av) below G.L. including fitting, fixing 3 nos. of 10 cm dia bullah as runner providing 1.80 mtr. long 10.0 cm dia bullah as tie bar @ 2.25 mtr c/c and 10.0 cm dia. and 3.0 mtr. long bullah as tie post @ 2.25 mtr. c/c driven @ 2.5 m below G.L. and walling with filling empty cement bags with earth and placing them in position including tying or sewing mouth including cost of thread including cost of all materials and two coat of coal tarring to all Eucalyptus bullah etc. complete including the cost of materials as per direction. |
| 4 | Construction of Embankment with Material obtained from Borrow pitsConstruction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 & 300-1 .The size course material in the mix of earth ordinarily shall not be exceed 75mm. (Reference to MoRT&H's specification clause 305). (Cost of compensation for Earth material & its carriage from private land at 5km distance have been included in the rate.) |
| 5 | Wet Mix Macadam (Base Course)Providing, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400-13 revised vide table 2 of IRC:109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 6 | Prime Coat (Type SS1) Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer using mechanical means (Reference to MORT&H's specification clause 502).i) On WMM/WBM surface @ 0.70-1.0kg/sqm. |
| 7 | Tack Coat (Type RS1) Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular/cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503). i) On bituminous surface @ 0.20kg-0.3kg /sqm. |
| 8 | Open-Graded Premix Surfacing using cationic Bitumen Emulsion Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510). Case - II: Open-Graded PremixSurfacing using cationic BitumenEmulsion |
| 9 | Seal Coat (Type B) Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)12(ii) Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 10 | R.C. Guard post Supplying fitting and fixing R.C. guard post 1.37m long with C.C. 1:2:4 with graded stone chips of 13.2mm down casting, curing complete including cost of providing 4nos.of 12mm dia. rod of length 1.54m as main reinforcement and 6 nos. of round shaped 8mm dia rods used as binders; the placing of the first binder should be at 75mm below the top finished surface and the other 5 nos of binders should be placed at 245mm c/c ; the guard post is of octagonal section with inscribed circle of dia 24cm at the base tapering to corresponding dimensions of 16cm at the top including two coats of painting with best quality synthetic enamel paint of approved make and grade to form 6 nos. horizontal alternate bands in white/tannery yellow and black to 90 cm length standing up above ground after mending good damages if any |
| 11 | Painting (one coat) guard posts with 6nos. of 16cm wide horizontal alternate band in different colours after the scrapping the surface free from old paint etc. as directed with best quality synthetic enamel paint of approved make and brand after fixing old existing guard post in correct position true to line and level with repacking the ground at base properly and mending good damages if necessary completein all respect. |
| 12 | Providing & Fixing Highway Grade ABS Speed Breaker (Temporary bumps) ((Size 325 mm x 250 mm x 50 mm (H) complete in all respect )) |
| 13 | Painting Lines, Dashes, Arrows etc on Roads in Two Coats on New WorkPainting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control (Reference to MORT&H's specification 803). (ii) Up to 10 cm in width |
| 14 | Supplying & fixing of Raised Pavement Markers/Road Studs/Cats Eye Supplying & fixing of Raised Pavement Markers/Road Studs/Cats Eye made of polycarbonate moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face which shall support a load of 13635 kg tested in accordance to ASTM D 4280 Type H and compling to Specifications of Category A of MoR&TH Circular No. RW/NH/33023/10-97 - DO III Dt. 11.06.1997 & MoRT&H's specification for Road &Bridge Works (Fifth Rev.). Marker height shall not be less than 10 mm and shall not exceed 20 mm, width shall not exceed 130mm and with minimum reflective area of 13 sqcm on each side and slope to the base shall be 35 ± 5 degree. Fixing will be without nails but by using epoxy resin based adhesive as per manufacturer's recommendation including site clearence etc and complete as directed by the Engineer-in-Charge. The contractor will have to provide a test certificate from a reputable national/international laboratory comforming the above specifications. |
| 15 | Retro-Reflectorised Traffic Signs Providing and fixing of retroreflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick,when signs with maximum side dimensions do not exceed 600mm, or with aluminium sheeting 2.0mm thick when signs with maximum side dimensions exceeds 600mm, supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (Reference to MORT&H'sspecification 801).4.(ii) 60 cm equilateral triangle |
| 16 | Direction and Place IdentificationSigns upto 0.9 sqm Size Board :-Providing and erecting direction andplace identification retroreflectorisedsign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing (Reference to MORT&H's specification 801). |
| 17 | Providing & fixing Concrete Sign Board as per IRC specification of size 900 x 750 x 37 mm. thick made with RCC 1:1½:3 with pakur variety stone chips reinforced with double layer IRC febric (75 x 75 mm. mesh) and fixed with necessary nuts & bolts on two RC precast posts 100 mm. x 150 mm. of height 2.65m. of which top 750 mm. is of section 100 x 13 mm. and 1.90 metre above GL & 0.75 metre below GL including digging hole, repacking the same with cement concrete 1:3:6 with jhama khoa or with local stone chips etc. complete including painting two coats on both faces lettering sign marks etc. as per direction of the Engineer-in-Charge. (The rate is inclusive of cost of reinforcement, concrete, shuttering, nuts & bolts, washer etc. complete.) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender