Tender For Special Repair And Conversion Of Bituminous Road Into Concrete Road And Allied Works Of Internal Road At Pachmarhi Mil Station
Tender Value
60 Lakhs
Estimated cost
Bid Submission
01 Dec 2026
9 days left
EMD
1.15 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hoshangabad → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair And Conversion Of Bituminous Road Into Concrete Road And Allied Works Of Internal Road At Pachmarhi Mil Station
BOQ
| Sl. No. | Item Description |
| 1 | Schedule \\"A\\" |
| 2 | Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area n exc 400 sqm depth exc 50 mm but n exc 100 mm. Complete all as spd and directed. |
| 3 | Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exc 400 sqm depth exc 50 mm but n exc 100 mm. Complete all as spd and directed. |
| 4 | Removing excavated material exc 250m but n. exc 500m and depositing where directed at a level n. exc 1.5m above the starting point as specified and directed. |
| 5 | M&L for WBM 75 mm thick (compacted thickness) in one layer of 75mm thick with coarse aggregates (granite/ basalt/ trap) of grading-2 (63mm to 40mm size) or grading-3 (50mm to 20mm size), spread, rolled and consolidated to required gradient and camber with 8 to 10 tonne tandem vibratory roller complete all as specified and directed. |
| 6 | M&L for applying evenly a priming/ tack coat of bituminous primer with paving bitumen VG-30 @ 10Kg/ 10Sqm by using mechanical sprayer on black top surface of road complete all as specified. |
| 7 | M&L for bituminous premixed asphaltic semi dense concrete 40 mm consolidated thickness with minimum 5.5% binder content using paving bitumen VG-30 by weight of total mix, rolled and compacted to required camber and gradient using 8 to 12 tonne tandem vibratory roller complete all as specified and directed.Notes:- (i) Bituminous premixed asphaltic semi dense concrete shall be prepared in hot mix plant only.(ii) Bituminous premixed asphaltic semi dense concrete shall be laid with sensor paver only.(iii) Binder content shall be tested at site as directed by Engr-in-Charge. |
| 8 | Rolling and consolidating formation surface of road in cutting with 8-12 tonne power roller, including watering & filling indepressions which occur during rolling complete all as specified. |
| 9 | M&L for 100 mm thick dry lean cocrete (DLC) of aggregate gradation as per table 1 of SP 49:2014 having 7 days compressive strength not less than 7 MPa . minimum cement content not less than 140 kg/cum complete as directed. |
| 10 | M&L for 200mm thick cement concrete work in pavement / hardstanding of flexture strength 40 Kg per Sqcm in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less including necessary formwork complete as directed. |
| 11 | M & L for finishing surface of concrete roads pavements by belting as specified and directed. |
| 12 | M & L for forming 20 mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade `A' for 200mm thick concrete slab as specified and directed. |
| 13 | M & L for forming Dummy joints 65mm deep X 10mm wide, filled with sealing compound Grade A as specified and directed. |
| 14 | M & L for forming construction joints 30mm deep X 10mm wide, filled with sealing compound Grade A as specified and directed. |
| 15 | Supply and laying 400 micron thick HDPE sheet (vergin quality) water proof , wrinkle free without punchure having minimum weight 390 gm/Sqm over sand cushion with overlap between adjacent strips and at tranverse joint as minimum 300 mm as specified and directed. |
| 16 | M & L for Providing 10mm thick sand coushion with clean river sand duly clear of residual, organic and deleterious materials spread evenly to uniform thickness laid over DLC layer. The sand cushion must not contain stones/other hard or uneven matter as specified and directed. |
| 17 | S&F for Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 laid in trenches of 32 mm dia Complete all as specified and directed. |
| 18 | M & L for 25mm dia mild steel TMT bars as in dowel bar including suitable metal cap at both ends partly filled with cotton complete all as specified and directed. |
| 19 | Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete. |
| 20 | Reinforcement cement concerete M-25 (desing mix) grade using 20 mm graded stone aggregate as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses and mass concrete all as specified and as directed. |
| 21 | Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batterfor rough finished flat surfaces complete all as specified and as directed. |
| 22 | Material and Labour for TMT bars 10mm dia and over dia cut to length, bent to shape required, including cranking, bending, hooking ends and binding with MS wire (annealed) not less than 9mm dia or securing with clips complete all as specified and as directed. |
| 23 | Demolition and breaking up drain pipes (SGSW, AC or RCC ) of internaldia 600 mm set in cement moratar complete all as spd and sirected |
| 24 | Material and Labour for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in foundation, mass concrete etc complete all as specified and as directed. |
| 25 | S&F in repair 600 mm dia (bore) RCC Hume pipes class NP-3 laid to slope and jointed in cement morter (1:1) complete with collars complete all as specified. |
| 26 | Material and Labour for rendering in CM 1:4, 10 mm thick on fair faces of brick work or concrete surfaces finished even and fair without using extra cement complete all as specified and as directed. |
| 27 | Material and Labour for applying two coats cement base paints over one coat of alkali resistant priming paint on newly plastered wall surfaces including preparation complete all as specified and as directed. |
| 28 | Demolition of cement concrete in ground floor and paving n.exc 15 cm below or above ground level. |
| 29 | M & L for Plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in subbase 100 mm thick |
| 30 | M&L for Moorum/red bajri filling, laid in layers n. exc. 15 cm thick, spread, levelled and rammed including watering as required complete all as specified and directed.Note:consolidated thickness shall be measured.Note:- (i) Compacted thickness shall be measured and paid.(ii) Rolling/ compaction shall be done by vibromax roller only. |
| 31 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified & directed |
| 32 | M&L for 80 mm thick rubber moulded reflective surface PU coated, factory made, coloured, Machine pressed precast concrete interlocking paver blocks/ tiles conforming to IS 15658-2006, M-40 designation of concrete as approved by GE, in hard standing, laid dry over & including 50mm thick sand cushion and filling the voids of paver blocks/tiles with dry sand complete all as specified & directed. |
| 33 | M&L for PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in coping ,benching,bed block for hold fast etc and the like including weathering slightly rounded/ chamfered angles with & including necessary use and waste of form work for fair faces of concrete, complete all as specified and directed. |
| 34 | M&L for near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 35 | S&F for single W-Beam road crash barrier as per IRC-119-2015 Morth Section 810 Galvanization of Min 550 gm/sqm zinc coating and having steel of min yeild strength 250 Mpa & tensile strength-- 410 Mpa with following specification ;-Single W Beam - as per IS 5986 Grade Fe 410 of 3.00mm Thick Cold Rold formed Post & Spacer as per IS5986 of 5.00 thick ( Size 150 x 75 mm)with spacing of 2.0 meter centre to centr and 85 cm above GL Mandatory safety feature- End terminals must be turned down into the ground , Red retro-reflective tapes( 100mm x 100mm) must be provided at 2 meter intervakls for night time guidance and upstream beam should overlap downstream beam by at least 150 mm Complete all as specified and directed. |
| 36 | Schedule of credit amount of Rs 15,170.50 to be deducted during AOC Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysDec 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender