Tender For Repair/Maint And Misc B/R Works In Mes Installation In Domestic Area At Af Stn Utarlai
Tender Value
20 Lakhs
Estimated cost
Bid Submission
25 Nov 2026
15 days left
EMD
40000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Barmer → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/Maint And Misc B/R Works In Mes Installation In Domestic Area At Af Stn Utarlai
BOQ
| Sl. No. | Item Description |
| 1 | Taking down frames with shutters (without taking off shutters from the frame) area not exc 1.5 sqm each incl iron mangery complete. |
| 2 | Taking down frames with shutters (without taking off shutters from the frame ) area exc 1.5 sqm but n.exc 4 sqm mtr each incl iron mongery complete. |
| 3 | Taking down shutters of any description exc 1 sqm but n.exc 2 sqm each for resecuring or easing & adjusting and refixing in same opening complete all as spcified and as directed. |
| 4 | S&F pressed steel frames of size 105 x 60mm for doors with one or more rebate including necessary fixing lugs, MS hinges, lock strike plate etc. including a coat of zinc chrome primer complete all as specified and directed by Engineer-in-Charge. |
| 5 | M&L Cement concrete 1:2:4 type B–1 filling of pressed steel frame and hold fast blocks etc all as specified and directed by Engineer - in - Charge. |
| 6 | S&F 35mm thick plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of vennered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified & directed by Engineer-in-Charge. |
| 7 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 8 | S&F 200 mm long, aluminum anodised barrel tower bolts of extruded section complete as specified. |
| 9 | S&F 150mm long aluminum alloy handles, anodized complete as specified. |
| 10 | S&F 250mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts and sliding bolts of extruded sections or cast-aluminium alloy. |
| 11 | S&F for aluminium door stopper of any descripion all as specified and directed by Engineer-in-charge. |
| 12 | S&F in repair drapery curtain rod, mild steel, rubber moulded 25mm dia with brackets, knobs, end stops etc all as specified and directed by Engineer - in - Charge . |
| 13 | M&L for preparation of new or untreated wooden surfaces of any description over 10cm width or girth not otherwise described and applying two coat of synthetic enamel paint over one coat of primer complete all as specified and directed by Engineer-in-Charge. |
| 14 | S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 15 | S&F in repair floor mounted door closer machine suitable for aluminium doors of upto 1 mtr opening complete all as specified and as directed. |
| 16 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified. |
| 17 | S&F for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane cut to required size complete all as as specified and directed. (Aluminium snap beading shall be paid separately) |
| 18 | S&F 3 mm thick figured glass pin headed and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engineer - in-Charge. |
| 19 | S&F powder coated (thickness or powder coating not less than 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing/sliding etc. complete all as specified and directed by Engineer-in-Charge. |
| 20 | S&F powder coated (thickness or powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, side/top hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) Complete all as specified and directed by Engineer-in-Charge. |
| 21 | S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed by Engr-in-charge. |
| 22 | S&F 4mm thick sheet glass ordinary quality, fixed in alum door/window shutter cut to required size and fixed with PVC/Neopane gasket etc. complete all as as specified and directed. (Aluminium snap beading shall be paid separately) |
| 23 | M&L powder coated (thickness or powder coating not less than 50 micron) anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, Complete all as specified and directed by Engineer-in-Charge. |
| 24 | Demolition of pcc block/brick work or stone masonry, built in cement mortar, complete all as specified and directed. |
| 25 | M&L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C1 using 20 mm graded stone aggregate, exc. 10 cm in width and setting in CM 1:6 complete. |
| 26 | Taking down cement plaster of any description on bricks, concrete or stone walls etc. including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed. |
| 27 | M&L for rendering 15mm in CM 1:4 thick on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement similar work up to 12 mtr height of the bldg complete all as specified and directed by Engineer-in-Charge. |
| 28 | M&L for rendering 15mm thick in CM 1:6 on concrete surface or brick work finished even and smooth with out using extra cement similar work up to 12 mtr height of the bldg complete all as specified and directed by Engineer-in-Charge. |
| 29 | M&L for rendering 5mm thick in CM (1:3) on concrete surface such as roof projection, chajja, fin and similar work incl. ceiling up to 12 mtr height of the bldg, finishing even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 30 | M&L for preparation of new plastered wall surfaces and applying two coats of acrylic smooth exterior weather coat paint @ 1.67 ltr/10 Sqm over one coat of exterior primer @ 2.20 Kg/10 Sqm (upto G+1 bldg) complete all as specified and directed by Engineer-in-Charge. |
| 31 | M&L for preparation of new plastered wall surfaces and applying two coat of oil bound distemper over one coat of interior wall primer over a coat of wall care putty complete all as specified & directed by Engineer-in-Charge |
| 32 | M&L for preparation on new plastered ceiling surfaces and applying three coats of white wash complete all as specified & directed by Engineer-in-Charge |
| 33 | M&L for preparation of old distempered wall surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and effloescent salts and trading oil and greasy spots and applying a coat of distemper oil emulsion any tinted complete all as specified and directed by Engineer-in-Charge. |
| 34 | M&L for complete removal of existing treeatment and applying two coats of oil bound distemper on wall surface over a coat of 1.5 mm thick wall care putty complete all as specified and directed by Engineer-in-Charge. |
| 35 | M&L for preparation on old plastered surfaces of ceiling & applying one coat of white wash (upto 12 mtr height of bldg) complete all as specified and directed by Engr-in-charge. |
| 36 | M&L complete removal of existing wall surfaces & applying two coats of acrylic smooth exterior weather coat paint @ 1.67 ltr/10 Sqm over one coat of exterior primer @ 2.20 Kg/10 Sqm (upto G+1 bldg) complete all as specified and directed by Engineer-in-Charge. |
| 37 | M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 38 | M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 39 | M&L complete removal of existing wall/coloumn/beam/cone wall/dome etc. surfaces of RCC overhead tank of staging 21 meter and capacity 50000 Gln & applying two coats of acrylic smooth exterior weather coat paint @ 1.67 ltr/10 Sqm over one coat of exterior primer @ 2.20 Kg/10 Sqm complete all as specified and directed by Engineer-in-Charge.Note : Work shall be executed for RCC overhead tank of staging 21 meter and capacity 50000 Gln at Gupta Pump House and rates are inclusive of all necessary scaffolding, T&P and also for removing beehives/ honeycombs. |
| 40 | M&L complete removal of existing wall/coloumn/beam/cone wall/dome etc. surfaces of RCC overhead tank of staging 18 meter and capacity 50000 Gln & applying two coats of acrylic smooth exterior weather coat paint @ 1.67 ltr/10 Sqm over one coat of exterior primer @ 2.20 Kg/10 Sqm complete all as specified and directed by Engineer-in-Charge.Note : Work shall be executed for RCC overhead tank of staging 18 meter and capacity 50000 Gln near RO Plant and rates are inclusive of all necessary scaffolding, T&P and also for removing beehives/ honeycombs. |
| 41 | M&L complete removal of existing wall/coloumn/beam/cone wall/dome etc. surfaces of RCC overhead tank of staging 6 meter and capacity 30000 Gln & applying two coats of acrylic smooth exterior weather coat paint @ 1.67 ltr/10 Sqm over one coat of exterior primer @ 2.20 Kg/10 Sqm complete all as specified and directed by Engineer-in-Charge.Note : Work shall be executed for RCC overhead tank of staging 6 meter and capacity 30000 Gln near RO Plant and rates are inclusive of all necessary scaffolding, T&P and also for removing beehives/ honeycombs. |
| 42 | M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces by forced application complete all as specified and as directed by Engineer-in-Charge. |
| 43 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed. |
| 44 | M&L for non skid coloured ceramic tiles 7 to 8 mm thick ( square/rectangular) in any shade area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors, skirting and similar work etc over screed bed or bedding layer 15mm thick in CM (1:4), set and jointed in neat cement slurry and pointed white or coloured cement to match complete all as specified and directed by Engineer-in-Charge. |
| 45 | M&L for non skid coloured ceramic tiles 7 to 8 mm thick ( square/rectangular) in any shade are of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors, skirting and similar work etc over screed bed or bedding layer 15mm thick in CM(1:4), set and jointed in neat cement slurry and pointed white or coloured cement to match. Complete all as specified and directed by Engineer-in-Charge. |
| 46 | M&L for coloured glazed ceramic tiles 350x250x7mm/450x350x7mm 7-8mm thick in vertical surface set and jointed in neat cement slurry and pointed with white/coloured cement to match the surface over rendering 10mm thick in CM (1:4) as in backing coat complete all as specified and directed by Engineer-in-Charge. |
| 47 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge. |
| 48 | M&L for 20-25 mm thick machine cut kota stone slab flooring as in floor, treads of staircase, window cills etc. in single piece over screed bed or bedding layer 20mm thick in CM(1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer-in-Charge. |
| 49 | Demolition of un-reinforced cement concrete in ground floors or pavings n. exc. 15 cm thick (below or above ground level) complete all as specified and directed by Engineer-in-Charge. |
| 50 | M&L for cement concrete 1:2:4 type B2 (using 40mm graded aggregate) in foundations, filling and mass concrete |
| 51 | M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded aggregate) as in sub base complete all as specified and directed. |
| 52 | M&L for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded aggr) as in level course finished even and rough with out using extra cement complete all as specified and directed. |
| 53 | M&L for 40 mm thick cement concrete (1:2:4) type B1 using 20mm graded aggregate finished even and smooth with using extra cement all as specified and directed. |
| 54 | M&L glass dividing strips, 3mm thick, width of strip 38mm and inserted in position to conform to design complete all as specified and directed by Engineer-in-Charge. |
| 55 | Provding and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour design & pattern as in footpath parks lowns drive ways or light traffic parking etc of requied strength, thickness & size shape, made by table vibratory mathod using PU monld, laid in required clolur & pattern over and inclding 50mm thick compacted bed fine sand compacting and proper embeddiing /laying of inter locking paver balocks into the sand bedding layer through vibratry compacton by using plate vibrator filling the joints with sand and cutting of paver blocks as per requird size and pattern finishing and sweeping extra sand.Complete all as specified and directed. |
| 56 | Provding and laying at or near ground lavel factory made kerb stone of M-25 grade cement concrete in position to the requied line, line, level and corvture jointed with cement mortar 1:3 including making joints with or without grooves (thickness of joints except at sharp curve shapp not to more than 5mm) incl making drainage opening wherver required complete all as specified and directed. |
| 57 | Dismantling stone slabs and tiles of any description or thickness laid/bedded dry in floors, aprons etc. |
| 58 | M&L for sand filling under floors or in foundations including spreading and levelling complete all as specified and as directed. |
| 59 | M&L (except tiles) i.e. laying only for machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed.Note :- Old tiles obtained from item No.57.00 will be reused in this item. |
| 60 | M&L for 75mm thick cement concrete (1:3:6) type C2 using 20mm graded stone aggregate as in paving/plinth protection incl. bitumen filler/mastic filling in joints complete all as specified and directed by Engineer-in-Charge. |
| 61 | S&F for framed work such as grill, gratings, etc with ends of bars shouldered and/or riveted or forged in to spikes, framed guard bars, barred iron doors ladders framed balusters and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed by Engineer-in-Charge. |
| 62 | S&F mild steel work as in hold fasts of flat iron, hooks, pintle hinges, cleats hand made sliding bolts and smilar items conforming to Fe-290 Gde-E-165 complete all as specified. |
| 63 | S&F 1.25mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed by Engineer-in-Charge. |
| 64 | Dismantling posts or struts (wood, steel or RCC) any section embedded in concrete including taking out embedded portion of concrete and making good distrubed ground all as directed. |
| 65 | Dismantling existing barbed wire of any thickness from fencing and remove to store complete all as specified and as directed. |
| 66 | M&L Cement concrete (1:3:6) type C2 (using 40 mm graded aggregate as in foundation of post, filling and mass concrete. |
| 67 | S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 all as directed. |
| 68 | Supply only chain link MS galvanised fencing any size all as specified and directed. |
| 69 | Fixing only chain link fencing any type of standards, rails straining bolts, etc including provision of binding wire. |
| 70 | S&F MS round bar 10mm dia and over for line wire to chain link fencing etc conforming to Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde-E-165) complete all as specified and as directed. |
| 71 | M&L for drilling and tapping holes upto 12 mm dia (and countersunk, if required), depth of hole exc. 3 mm but n exc. 12 mm in existing MS posts for securing fencing wire mesh etc. complete all as specified and as directed. |
| 72 | S&F MS screw bolt (machine made) with hexonal or screwed head at one end and screwed the other end, and fitted with washer and one hexagonal or square nut n. exc 5cm long and 5 mm to 10mm dia bolt. |
| 73 | M&L for preparation of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 74 | M&L for preparation of new steel surfaces of any description n.exc.10cm in width or girth and when unconnected with other painting or when painted in a different tint applying two coats of synthetic enamel paint over a coat of red oxide zinc chrom primer complete all as specified and directed. |
| 75 | S&F in repair PVC water tank cover best quality suitable for 10000 ltrs capacity water tank complete as specified and directed by Engr-in-charge. |
| 76 | Disconnecting existing tanks of capacity exc. 250 and n exc. 500 ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) |
| 77 | Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. from water tanks of capacity exc. 250 and n exc. 500 ltrs incl. writing date of cleaning of tank in DD-MM-YY format complete all as specified and as directed. |
| 78 | S&F in repair gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia complete all as specified and as directed. |
| 79 | S&F 15mm bore galvanised iron steel water tubing medium grade with all fittings and fixed to wall/ceiling or laid in floors incl taking up or down existing steel tubing and connections fixed/laid in any situation and removing to store complete as specified and directed by Engr-in-charge. |
| 80 | S&F in repair 15mm bore CP Angle cock two way, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified . |
| 81 | S&F in repair 15mm stop valves fancy type, chromium plated with long shank and cup (concealed type) ,cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed. |
| 82 | S&F in repair pillar taps 15mm bore fancy type chromium plated cast copper alloy with capstan heads scre-wed down high pressure with or without lettered hot' or'cold' with long screwed shanks and fly nuts screwed for iron pipe . ISI marked. |
| 83 | S&F in repair CP grating suitable for 75/100 mm bore floor trap and fixed with white cement. |
| 84 | S&F in repair PVC connection both side brass unions internal for size 15mm dia and 600mm long all as specified and directed by Engineer-in-Charge. |
| 85 | S&F PVC waste pipe 32mm dia & 90 cm long all as specified and directed by Engineer-in-Charge |
| 86 | S&F in repair stainless steel towel ring holder of square shape and of size 185x100mm superior quality and fixed with chromium plated screws complete all as specified and directed. |
| 87 | S&F in repair stainless steel soap dish of size 250x100mm, with double soap holder for bathroom, fixed to wall with plugs with chromium plated screws complete all as specified and directed. |
| 88 | S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) but including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, seat cover complete. |
| 89 | S&F in repair PVC low level flushing cistern 10 Ltr capacity with 10 ltr discharge option flush pipe complete as approved by Eng-in charge. |
| 90 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 91 | S&F in repair EWC Jet spray mild steel chromium plated suitable for 15 mm dia pipe including making connections and fixed in position complete in all respect as specified. |
| 92 | S&F in repair vitreous china,white wash hand basin ,pedestal type, flat back size 550x400mm complete all as specified and directed by Engineer-in-Charge. |
| 93 | S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed. |
| 94 | S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (minimum weight 60gms) complete all as specified and as directed. |
| 95 | Taking down eves and gutter and rain water of any size all as specified and directed by Engineer - in - Charge . |
| 96 | S&F 75mm PVC (SWR) pipes of 4 kg/cm² pressure rating, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 97 | S & F 110mm PVC (SWR) pipes of 4 kg/cm² pressure rating, single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed. |
| 98 | S&F 75mm PVC (SWR) junction single, (single T) equal or unequal provided with access door complete all as specified and directed. |
| 99 | S&F 75mm PVC (SWR) vent cowl fixed in position complete all as specified and directed. |
| 100 | S&F 75mm PVC (SWR) bends any radius complete all as specified and directed. |
| 101 | S&F PVC (SWR) floor trap 100/75 mm bore with grating including jointing to waste pipe and fixed with PCC 1:2:4 complete all as specified. |
| 102 | S&F PVC stack clamps of suitable for 75mm and 110mm bore pipes fixed to walls including bolts and nuts and securing ends of stays completeall as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysNov 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender