Defence Statutory Bodies & Commissions/Committees Closing in 9 days TDR #58340060

Tender For Additional / Alteration And Special Repairs To Selected Officers Married Accommodation At Saugor Military Station

Issued by Statutory Bodies & Commissions/Committees · Sagar, Madhya Pradesh
Tender Value
3.39 Crore
Estimated cost
Bid Submission
01 Dec 2026
9 days left
EMD
4.15 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Sagar → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Additional / Alteration And Special Repairs To Selected Officers Married Accommodation At Saugor Military Station

BOQ

Name of Work:- ADDITIONAL / ALTERATION AND SPECIAL REPAIRS TO SELECTED OFFICERS MARRIED ACCOMMODATION AT SAUGOR MILITARY STATION
Sl. No. Item Description
1Note: (i) Please refer schedule 'A' notes before quoting the tender. (ii) Amount of Schedule of credit shall be deducted off line by the department.
2Demolition of cement Concrete unreinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed.
3Demolition of reinforced cement concrete any description and in any position n.exc 15cm thickness complete all as specified and directed.
4Demolition of brick work or stone/boulder masonry, built in cement mortor incl all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.
5M&L for Brick work with kiln burnt bricks ( old size) subclass 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6, complete all as specified and directed.
6M&L for Brick work with old size subclass 'B' bricks, straight or curved on plan in half brick thick wall built in CM 1:4, complete all as specified and directed.
7M&L for Raking out joints/ pointing in cement mortar to squared rubble masonry, coursed or uncoursed complete all as specified and directed.
8Taking down cement plaster on brick work or stone walls, etc incl raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.
9S&F checken wire mesh 0.5mm dia and aperture size 25mm fixed in position etc complete all as specified and directed.
10M&L for rendering 15 mm thick on brick work or concrete surfaces in CM 1:6 and finished the sufarce fair and even complete all as specified and directed.
11M&L for doubbing out average 15 mm thick cement plaster in CM 1:6 on irregular faces of stone masonary wall, and second coat cement plaster 10 mm thick in CM 1:4 on stone masonry finished the surface fair and even complete all as specified.
12M&L doubbing out average 15 mm thick cement plaster in CM 1:6 on irregular faces of stone masonary wall and second coat cement plaster 5mm thick in CM 1:4 with WPC @ 200 ml per bag of cement on brick work or concrete surfaces finished even and fair (WPC will be paid seperately under respective item) complete all as specified and directed.
13M&L two coat cement plaster, first coat 10 mm thick CM 1:6 and second coat cement plaster 5mm thick in CM 1:4 with WPC @ 200 ml per bag of cement on brick work or concrete surface finished surface fair and even. (WPC will be paid seperately under respective item) complete all as specified and directed.
14M&L Rendering 10 mm thick on fair faces of brickwork /concrete surfaces in CM (1:3) in ceiling finishing the surface fair and even complete all as specified and directed.
15M&L Rendering 10 mm thick on fair faces of brickwork concrete surfaces in CM (1:3) in ceiling in patch work (not exc 3 sqm each patch) finishing the surface fair and even complete all as specified and directed.
16M&L for two coat cement plaster, first coat 15 mm thick CM 1:6 and second coat cement plaster 10mm thick in CM 1:4 for rendering in patch work ( n exc 3 sqm each patch) on brick work , stone or concrete surfaces finished the sufarce fair and even complete all as specified and directed.
17Supply only liquid water proofing compound complete all as specified and directed.
18M & L for complete removal of existing treatment and applying two coat of acrylic distemper over a coat of interior primer and applying white putty of approved make 1 mm thick in two layer for levelling the surfaces incl. preparation of old surfaces of walls etc complete all as specified and directed. NOTE :- The VOC contents of the distemper shall be less than 50 gms per litre. The shade & colour shall be as approved by GE.
19M & L for applying two coat of acrylic distemper over a coat of interior primer and applying white putty of approved make 1mm thick in two layer for levelling the surfaces incl. preparation of new surfaces of walls etc complete all as specified and directed. NOTE :- The VOC contents of the distemper shall be less than 50 gms per litre. The shade & colour shall be as approved by GE.
20M & L for complete removal of existing treatment mechanically and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 sqm including properly making of V shape crakes wherever applicable and filling of all crakes with crakes seal over and including priming coat of exterior primer applied @ 0.90 litre / 10sqm over old surfaces and applying white putty of approved make 1 mm thick in two layer for levelling the surfaces including preparation of surfaces of old decorated walls etc complete all as specified and directed.
21M & L for applying two of 100% Premium acrylic emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 sqm including priming coat of exterior primer applied @ 0.90 litre / 10sqm over new surfaces and applying white putty of approved make 1 mm thick in two layer for levelling the surfaces including preparation of surfaces of new walls etc complete all as specified and directed.
22M&L for complete removal of existing treatment of old wall surfaces and applying two coats of White wash on wall surfaces complete all as specified and directed.
23M&L for Applying three coats of white wash on new wall surface including preparation of surface complete all as specified and directed.
24M&L for complete removal of existing treatment of old ceiling surfaces and applying two coats of White wash on ceiling surfaces complete all as specified and directed.
25M&L three coats of White wash on newly plaster surface of ceiling including preparation of newly surface complete all as specified and directed.
26Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.50 but n exc n.exc 4 Sqm each complete all as specified and directed.
27Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) n.exc 1.5 Sqm each complete all as specified and directed.
28S&F 105 mm X 60 mm size pressed steel frames for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of red oxide primer including cutting holes and making good in P:C:C 1.2.4 type B-1 using 20 mm graded stone aggregate and M&L PCC 1:3:6 type C-0 using 12.5 mm graded store aggregate for filling in pressed steel frame complete all as specified and directed.
29S&F 125 mm X 60 mm size pressed steel frames for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of red oxide primer including cutting holes and making good in P:C:C 1.2.4 type B-1 using 20 mm graded stone aggregate and M&L PCC 1:3:6 type C-0 using 12.5 mm graded store aggregate for filling in pressed steel frame complete all as specified and directed
30S&F 35mm thick flush shutters factory made, solid core construction, with block board core and plywood face panels commercial type on both side including both side decorative laminate 0.9mm thick type 1 of surface finish, colour and pattern as approved & fixed with approved adhesive as per manufacturer instruction complete all as specified and directed.
31S&F, second class hard wood, 35mm thick glazed and skeleton shutters factory made, open rebated and prepared to receive glass, gauge, etc. (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats complete all as specified and directed.
32M&L two coats of synthetic enamel paint over a coat of pink primer on newly wood/wood based surfaces over 10cm width or girth incl preparation of new surface.
33S&F 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.
34S&F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.
35M&L for 300mm Aluminium alloy, anodised, sliding door bolt (not less than 15 mm dia) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.
36S&F MS 150 mm ordinary rat rail tail rod pattern springs including roller and roller plate complete
37S & F door stopper of aluminium alloy body and tounge 150 mm long, anodised fixed in door with screw etc
38S&F Solid PVC door frame of size 50mmX47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet (edges will be painted to match with prelam sheet) reinforced with MS square tube, suppling & fixing in opening as per specification complete all as specified and as directed.
39S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 5 mm thick moulded prelam PVC sheet on the front face & 5 mm thick prelam PVC sheet on back face, 18- 20 mm thick centre core will be PVC battern supplying & fixing in frame at site complete all as specified and directed by Engineer-in-Charge
40S&F 100 mm butt hinges extruded aluminium alloy with galvanised mild steel hinges pin, anodised and fixed.
41S&F 125 mm long aluminium handles cast type anodised etc all as specified complete all as specified and directed.
42S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.
43S&F aluminium windows sliding type three track powder coated consisting of frame bottom with sutter of size min 92 X 31.75 mm,side and top of size min 92 X31.75, shutters vertical 39X20 mm,shutter top &bottom of size min 20X39 mm ,shutter interlock min size 39X20 mm with rollers and concealed locking arrangements with 5 mm thick plain sheet glass with rubber gasket,brush and aluminium beading , aluminium grill with fixing arrangement stainless steel mess 0.36 mm dia and aperture 1.45 mm etc including necessary cutting holes on wall and floor and confirming to IS complete all as directed by Engineer-in- Charge.(Al. section thickness 1.50 mm ).
44Providing and fixing of double rebate openable / fixed windows aluminium anodised consisting of frame of size min 63 X 38.1 mm, shutters frame for glass and wire gauzed shutter of size 38.1X19.05 mm, with locking arrangements with 5 mm thick plain sheet glass with rubber gasket,brush and aluminium beading , aluminium wire mess 0.36 mm dia and aperture size 1.45 mm etc including necessary cutting holes on wall and floor and confirming to IS complete all as directed by Engineer- in- Charge (Al. section thickness 1.50 mm }
45S&F fixed type ventilators aluminium powder coated of frame size 50.80X 25.40mm,1.5 mm thick half portion will be fixed with 4mm thick frosted glass and half portion will be fixed with louvers with 4mm thick frusted glass with rubber gasket and aluminium beading ,aluminium grill with fixing arrangement (wt. of grill not less then 2.50 kg/sqm),aluminium wire mess 0.36 mm dia and aperture size 1.45 mm to be fixed over louvers portion only including necessary cutting holes on wall and fixing arrangements complete all as specified and directed by Engr-in- Charge (Al. section thickness 1.50 mm }
46S&F MS framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors etc conforming to Fe 410-O or Fe 310-O including PCC 1:3:6 type C1 using 20mm graded stone aggregate as in hold fasts, coping, filling of ms frame bed blocks, etc complete all as specified and directed.
47M&L Two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces over 10cm width or girth incl preparation of new steel surfaces complete all as specified and directed.
48M&L for one coat of synthetic enamel paint including preparation of old steel surface of any description, over 10cm in width or girth, not otherwise described complete all as specifed and directed.
49S&F galvanised mild steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.45mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.
50M&L for second class hardwood plain, solid, straight chowkhat and frames, wrought framed rebated on the solid, rounded on the solid or chamfered put together with glue pinned at joints, supplied and fixed complete all as specified and directed.
51S&F in repair 18 mm thick marine plywood interior grade with 1 mm thick white mica lamination on one side and 1 mm thick coloured mica on another side fixed in cubboard shutter and kitchen cabinet complete all as specified and directed .
52M& L for external teak wood lipping, 6mm thick, fixed with nails for 18/19mm thick plywood including necessary preparation of surfaces and polishing complete all as specified and directed.
53S&F for continuous (piano) hinges mild steel bright finish or electro galvanised width of width of flaps nexc 30 mm (when open), complete all as specified and directed.
54S&F for extruded aluminium alloy handle of 100 mm size fabricated type, anodised complete all as specified and directed.
55S&F 100 mm Hasp and staple, safety type, aluminium anodised, with mild steel hinge pin including bolting hinge plate and fixed with screws complete all as specified and directed.
56S&F for magnate catcher of metal body and striking plate heavy duty including fixed with screw, complete all as specified and directed.
57S&F stainless steel hat pegs solid body set of six Nos fix to wall complete all as specified and directed.
58S&F in repair 25mm dia stainless steel curtain rod not less than 0.70mm thick including fixing of sufficient brackets ( minium 2 nos at every 1.50m length) & end Knobs complete all as specified and directed.
59M&L RCC 1:2:4 (nominal mix) type B1 using 20mm graded stone aggregate as in landing, cooking platforms, shelves and the like complete all as specified and directed.
60Use and waste of formwork to soffits of suspended slabs, landings, shelves and similar work n exc 200mmm thick horizontal or sloping complete all as specified and directed.
61M&L Mild steel TMT bars 10mm dia and over cut to length bend to shape as required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe 410-O or Fe 310-O complete all as specified and directed.
62M&L Mild steel TMT bars above but 6 to 8mm dia bar and over cut to length bend to shape as required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe 410-O or Fe 310-O.Ditto complete all as specified and directed.
63Excavation over areas , n exc 1.5 m deep and getting out soft/loose soil complete all as specified and directed.
64Approved earth filling with approved soil brought from out side MD land, filling in trenches or paving laid in layers not exceeding 25 cm thick spread, levelled and rammed including watering etc complete all as specified and directed.
65M & L broken stone or boulders hard core of gauge n.exc 63mm deposited spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface complete all as specified and directed.
66M&L for 75mm thick PCC 1:3:6, type C-1 (using 20mm graded stone aggregates) as in plinth protection surface finished even and smooth without using extra cement & provided with construction joint on the interval not more than 3.0m and filled with bitumen and sand mortar in 1:3 complete all as specified & directed.
67M&L for plain cement concrete type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundations, foundation filling and mass concrete complete all as specified and directed.
68Dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding ,removal servicable tiles to store and rubbish off the premises, complete all as specified and directed.
69M&L 25mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in sub base of floor complete all as specified and directed.
70S&F for 8-10 mm thick coloured vitrified tiles area of each tiles not exceeding 0.36 sqm in floors set & jointed in neat cement slurry and pointed in white /coloured cement to match the tiles over and including 15 mm thick screed bed in CM 1:4 all as specified and directed.
71S&F for 8-10 mm thick coloured vitrified tiles area of each tiles not exceeding 0.36 sqm in dado / skirting etc. set & jointed in neat cement slurry and pointed in white /coloured cement to match the tiles over and including 10mm thick rendering in cm (1:4) complete all as specified and directed.
72M&L Non skid ceramic coloured tiles 7 to 8mm mm thick (Square/ rectangular) area of each tiles exceeding 0.11sqm but not exceeding 0.18 Sqm, in floors etc over and including 15 mm thick cement screed bed in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.
73M&L Non skid ceramic coloured tiles 7 to 8mm mm thick (Square/ rectangular) area of each tiles exceeding 0.11sqm but not exceeding 0.18 Sqm, in dado / skirting etc over and including 10mm thick rendering in cm (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed
74M&L for glazed ceramic tiles area of each tiles exceeding 0.11 sqm but not exceeding 0.18sqm 7 mm thick,(joint free (rectified)) coloured, on vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed in white/ coloured cement to match over 15 mm thick rendering in CM 1:4 complete all as specified and directed.
75M & L for granite stone 18 to 20mm thick machine cut, bedding & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone, fixed over 15mm thick screed bed in CM 1:4 as in cooking plaform and fixed in window cill as in single piece including cutting and polishing, rounding the edges etc complete all as specified and directed
76M&L for Machine cut kota stone single piece slab as in steps tread,windows cill,18-20 mm thick ,over and including 15 mm thick screed in CM(1:4) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing , polishing and rounding the edges complete all as specified and directed.
77M&L Kota stone slab 12-15 mm thick in skirting, steps riser etc over and including 10mm thick plater in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including, rubbing & polishing complete all as specified and directed.
78M&L for Machine cut kota stone slab flooring as in landing and entrance of staircase 18-20 mm thick over 15mm thick screed in CM(1:4) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including, rubbing & polishing complete all as specified and directed.
79Taking down steel tubing 15mm bore and connection, incl cleaning for refixing or removal from site complete all as specified and directed.
80S&F 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors incl fittings and the holes in walls and floors shall be made by drilling with drill or jumper and not by dismantiing the brick/concrete. After fixing holes shall be made good with CM 1:3 properly, complete all as specified and directed.
81Taking down steel tubing 20mm bore and connection, incl cleaning for refixing or removal from site complete all as specified and directed.
82S&F 20mm dia tubes medium grade gavanised with all fittings and fixed complete to walls and ceiling or laid in floors complete incl the holes in walls and floors shall be bade by drilling with drill or jumper and not by dismantiing the brick/concrete. After fixing holes shall be made good with CM 1:3 properly complete all as specified and directed.
83Cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, cutting n exc 10cm girth. pinning in, making good to facings where required and pointing in CM 1:3 on stone walls complete all as specified and directed.
84S&F in repair sink mixture cast copper alloy, chromium plated screwed for iron pipes and fixed complete all as specified and directed.
85S&F in repair 15mm bore CP fancy type brass bib taps cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed (weight not less than 400gms).
86S&F in repairs Two way bib cock with wall flage chromium plated brass complete all as specified and directed.
87S&F CP hot & cold water wall mixure unit with with arrangement for overhead shower and with hot & cold valves cast copper alloy type heavy duty fixed to 15mm bore of pipe complete fixed in repair complete all as specified and directed.
88S&F in repair 15mm bore stop valves/angle valve and concealed valve, cast copper alloy fancy type chromium plated, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.
89S&F in repair 125 mm size brass chormium plated shower rose fancy type including fixing to steel pipe or union complete all as specified.
90S&F in repair Wash hand basin mixture15mm bore cast copper alloy, with capastan heads, chromium plated, screwd down high pressure, with lettered 'hot' or 'cold' with long screwed shanks and fly-nuts, screwed for iron pipes and fixed complete all as specified and directed.
91S&F in repair Vitreous China wash down water closet pan (pedestal pattern), P or S trap colour white or Ivory with connecting all fitment including white seat cover complete.
92S&F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.
93S&F in repair vitreous china squatting pan 'Orrisa pattern' size 580x440mm white with integral foot rests any pattern including provn of cement concrete bedding and making connection with & including Por S Trap, etc complete all as specified and directed.
94S&F in repair vitreous china WHB white flat back size 550x400mm including S&F angle iron brackets, CP waste coupling, 32mm dia,PVC connection and PVC waste pipe 32mm dia complete all as specified & directed.
95S&F Vitreous China full size pedestal for wash hand basin complete all as specified and directed.
96S&F in repairs Sink single bowl made of stainless steel 1mm thick kitchen or laboratory with plugs, washers ,waste pipes and brass waste coupling, incl bedding in cement mortar to dwarf wall or incl fixing cantilever brackets and connecting union to pipe overall size of bowl 610mmx460mmx254mm , complete all as specified and directed.
97S&F in repair Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x420mm with bowl size 410mm x330mm x160mm complete all as specified and directed.
98S&F Stainless steel kitchen plate rack of thickness 0.6 mm thick and size 31\\" X 36\\" X 10\\" fixed with screws complete all as specified and directed.
99S&F in repair PVC low level flushing cistern of 10 Ltr capacity(dual5 Ltr/10 Ltr) valve less including flushing pipe bend PVC bend,Pvc connection etc. complete all as specified and directed.
100S&F CP tubular towel rail 600mm long between flanges, 20mm dia, D type etc all as specified.
101S&F in repair PVC bath room cabinet with mirror of approved make complete all as specified and as directed.
102S&F in repairs purposely moulded looking mirror 5 mm thick glass fixed with studs all as specified and directed by Engr-in- charge.
103S&F in repair Bevelled edge looking mirror of size 600x450 selected quality glass mounted 6mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated screws and cup washer all as specified & directed.
104S&F soap dish brass chromium plated fixed to wall with brass chromium plated screw and wooden/ plastic plug etc.
105S&F corner Sheet glass shelf assembly complete all specified and directed.
106S&F in repairs Toilet paper holder with flap chromium plated brass complete all as specified and directed.
107S&F 500 ltr capacity of rotational moulded polyethyline water storage tank (Cylindrical vertical with closed tape) hoisted & fixed in position incl S&F 20mm dia GI Pipe medium grade washout pipe 450mm long with plug & 20mm dia GI pipe medium grade overflow pipe 600 mm long with fittings complete all as specified & as directed incl. Dismantling water tanks complete all as specified and directed.
108M & L Disconnecting existing PVC tanks exc 500Ltrs and not exc 1000ltrs , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.
109S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 1000 Ltrs Capacity incl. Dismantling water tanks complete all as specified and directed.
110S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.
111S&F 20mm bore Ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed in repairs.
112S&F in repair PVC (SWR) Pipe single socketed in any length with adhesive joint laid in floor or fixed to wall with clamps for 110mm dia
113S&F in repair PVC (SWR) Pipe single socketed in any length with adhesive joints laid in floor for or fixed to wall with clamps 75mm dia
114S&F PVC in repair bends any radius 110mm dia provided without access door
115S&F PVC in repair Bends any redius 75mm dia provided with access door
116S&F PVC in repair (SWR) Junction single T equal or unequal 110mm dia provided with access door
117S&F PVC in repair (SWR) Junction single T equal or unequal 75mm dia provided with eccess door
118S&F in repair PVC vent cowl 110mm dia
119S&F in repair for 75mm outlet dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.
120M & L for PCC ( 1: 2: 4) type B-0 using (12.5mm graded stone aggregate) etc on roof top as a leveling course / padding to maintain the slope,finished the surfaces even and smooth without using extra cement etc complete all as specified and directed.
121M&L rendering 10 mm thick in cement mortar 1:4 mixed with and including water proofing compound @ 200 ml per bag of cement applied over roof slab ,complete all as specified and directed.
122Taking down of old roof treatment of any description including mud phushka, lime, concrete,tiles , cement plaster, padding upto 30cm depth from roof surfaces etc including cleaning, brushing and watering to joints and grooves and throwing the same to a distance exc 250 mtr and n exc 500 mtr from the roof of height 3 to 9 m height etc .
123M&L for provn of water proffing roof treatment to RCC roof with approved modified membrane of weighing not less than 3 kg/sqm comprising with following items and all as specified. (1) The surface of roof,parpet and gutters drain mouths etc over which water proofing treatment is to be applied shall be cleaned of all foreign matter such as fungus,mass dust etc by wire brushing and dusting. For cast iron drain outlets a groove shall be cut as specified and directed. A fillet of PCC (1:2:4) of 100x100mm shall be provided at all junctions of vertical and horizontal surfaces and wherever there is a change of dirction. The membrane should not be taken over at any steep turns and hence all corners/timers should be rounded. (2) Oil based Bitumen primer conforming to IS-3384-1986 @ 0.3 kgs per sqm to be applied on prepared surface till the surface is properly impregnated. (3) Applying one coat of hot blown grade bitumen 85/25 grade @ 1.20 kg/Sqm (4) Laying of water proofing teratment of weight not less than 3 Kg / sqm APP modified polymeric water proofing membrane composed of 100 micron (+10% ) high density polyethylene sheet ( HMHDPE) as center core, which is standwiched between high quality polymeric bitumen mix having softening , high heat resistance and cold flexible protected on either side with a thin thermo fusible HMHDPE film with side and laps 75 mm and 100 mm as per manufacture instruction etc. (5) Applying one coat of hot blown grade bitumen 85/25 grade @ 1.20 kg/Sqm over the membrane (6) Applying aluminium paint in two coat @ 100 gm/sqm in each coat on finished membrane surfaces complete all as specified and directed at site .
124M&L for provn of water proofing roof treatment to RCC roof with approved modified membrane of weighing not less than 3 kg/sqm comprising with following items and all as specified as under:- (1) The surface of roof,parpet and gutters drain mouths etc over which water proofing treatment is to be applied shall be cleaned of all foreign matter such as fungus,mass dust etc by wire brushing and dusting. For cast iron drain outlets a groove shall be cut as specified and directed. A fillet of PCC (1:2:4) of 100x100mm shall be provided at all junctions of vertical and horizontal surfaces and wherever there is a change of dirction. The membrane should not be taken over at any steep turns and hence all corners/timers should be rounded. (2) Oil based Bitumen primer conforming to IS-3384-1986 @ 0.3 kgs per sqm to be applied on prepared surface till the surface is properly impregnated. (3) Applying one coat of hot blown grade bitumen 85/25 grade @ 1.20 kg/Sqm; (4) Laying of water proofing treatment of weight not less than 3 Kg / sqm APP modified polymeric water proofing membrane composed of 100 micron (+10% ) high density polyethylene sheet ( HMHDPE) as center core, which is standwiched between high quality polymeric bitumen mix having softening , high heat resistance and cold flexible protected on either side with a thin thermo fusible HMHDPE film with side and laps 75 mm and 100 mm as per manufacturer instructions etc.; (5) Applying one coat of hot blown grade bitumen 85/25 grade @ 1.20 kg/Sqm
125M&L for cool roof ceramic tiles 8-10mm thick 300x300mm size , white confirming to sun reflective Index (SRI) value minimum of 70-80, laid with minimum 3 mm thick spacers, & joints should be filled with epoxy joint filling compound on 15 mm thick over & including 1:3 CM screed bed complete all as specified and directed.
126Treatement for sunken portion is as follows :- (1) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (2) M&L for providing 12 mm dia holes of 40mm deep @200mm c/c at junction of beams and columns as co-ordinal points for inserting/pouring cement slurry with grouting compound of approved make by pressure grouting for sunken floors of toilet , includindg sealing the holes with CM 1:3, all as specified and directed by EIC. (3) M&L for water proofing plaster for sunken portion in CM 1:3, 20 mm thick in two coats with water proofing compound at the rate of 200 ml per 50 kg bag of cement and finishing the surface even and smooth without using extra cement. (4) M&L for applying two coats of compound of approved make suitable for sunkun treatment as per manufacturer instructions over vertical surfaces and floors of sunken of toilet including cleaning of surfaces. (5) M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in filling (sunken portion). etc. (6) M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate, mixed with WPC @ 200 ml per 50 kg bag of cement, as sub base, 75mm thick on top. Note :- Above includes (a) Test again of water tightness by pounding for 72 hours & rectify defects if any till total elimination of defect.(b) The sunken portion shall be tested for leakage / seepage / dampness by pounding with water for 72 hours. In case any defect is noticed the portion shall be grouted with suitable chemical of approved make & tested again. The process of grouting and testing shall be repeated till leakage / seepage / dampness is eliminated (c) Horizontal flat area to be measured complete all as specified and directed.
127S&F in repair mild steel, plain, black sheet 1.25 mm thick welded to existing steel gate farmes and similarwork, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.o 2.10 M.]
128M&L for cement concrete ( 1:2:4) type B-0 (12.50 mm graded agrregate) in lintels upto 1.5m clear span, cills, stes, seimic and other similar bands, plinth course, string course, lacing cours, arapets and railings upto 60cm in height, coping, kneelers, apex stones, bed plates, kerbs, water throughs and the like including wheathering slightly rounded or chamfered angle and throating, including form work, complete all as specified and directed.
129Labour only for removal of unsound RCC by hammer chiseling or pneumatic chopper and exposing reinforcement all around including providing jacking up arrangement or temporary supports of adequate strength to avoid any damage to the existing structure and removing rubbish to outside MD land complete all as specified as directed.
130M & L for cleaning exposed rusted reinforcement in site with wire brushes and applying polymer based rust remover (Rust removing chemical) of approved make as per manufacturers instructions complete all as specified and as defected
131Labour only for welding with new additional reinforcement bars as required of site i.e. where dia of existing bar is found reduced than the original size of bars complete all as specified and directed Note: supply only reinforcement bars will be measured and paid separately under respective items here in before
132M&L for priming the old and / or new steel reinforcement with one coat of epoxy zinc primer of approved make by brush application
133M&L for hard drawn steel wire fabric cut to length bent to shape, dia of fabric 3 mm and aperture 50 mm, cover entire steel surface, not exceeding 4 kg per Sqm complete all as specified and directed
134M&L for bounding the entire exposed surface with one coat of SBR bonding agent of approved make as per manufacturers instructions complete all as specified and directed
135M & L for one layer of spray concrete 20mm thick (comprises composition 1:2:1 plain cement concrete i.e. one part of cement two parts of fine aggregate and one part of 10mm and down size trap stone aggregate) mixed with chloride free accelerating admixture of approved make 2 to 2.5 % weight of cement and 12.5 to 16.5 liter of water mixed as per manufacturers instructions an gunnting pressure nozzle with a delivery capacity of 2.5 kg Sqm over column beam roof slab and other similar work.
136M & L for 10 mm thick rendering in cement mortar 1:4 over guniting concrete surface and finished the surfaces even and smooth or matching/ flushing with adjoining plastered surfaces .
137S&F Stainless steel wire cloth 0.36 mm nominal dia and wire and average width of aperture 1.40 mm fixed with stainless steel staples complete all as specied and directed.
138S&F Aluminium alloy, anodised, sliding door bolt 250 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed.
139S&F provn of door closer hydraulically regulated, aluminium body, designation No. 3, universal type, suitable for door shutters of weight between 61 to 80 Kg complete all as specified and directed.
140S&F 18mm to 20mm thick solid factory made PVC board for cupboard /kitchen cabinate shutter with one side 1mm thick printed pvc sheet other side plain pvc sheet suitable fixed with &including suitable pvc frame, matching coloured beading to cover all edges & screwed portion of frame, Magnetic catcher with all necessary fixing arrangement as per specification & drawing complete all as specified & directed.
141S&F 100 mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.
142S&F glass shelf assembly 60 cm long 5 mm thick glass , chromium plated guard and fixed to wooden plug with chromium plated screws and cup washer as specified.
143S&F in repairs 110mm dia PVC(SWR) pipes single socketed in any length with rubber ring jointed laid in trenches or in floors complete all as specified
144S&F in repairs 110mm dia PVC(SWR) pipes single soketed in any length with rubber ring jointed and fixed to walls with & including clamps complete all as specified
145S&F in repairs 75 mm dia PVC(SWR) pipes single soketed in any length with rubber ring jointed laid in trenches or in floors complete all as specified
146SS&F 75 mm dia PVC(SWR) pipes single soketed in any length with rubber ring jointed fixed to wall with & including clamps complete all as specified
147S&F in repairs 75mm dia PVC (SWR) multi floor trap with Hinge type SS grating including jointing with solvent cement complete all as specified & directed.
148S&F PVC (SWR) bends 75 mm dia with accessable door complete all as specified & directed.
149M&L provn for coloured designer (anti slip with grip) tiles for parking / pathway of size 300x300mm exterior grade, heavy duty 10 mm thick laid over and including 15 mm thick cement mortar 1:6 set and jointed in floor and pointed in neat cement slurry with grey cement and pigment in floor etc and removing rubbish from site complete all as specified and directed.
150M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces (for manholes etc.)in CM (1:4) finished fair and even complete all as specified and directed.
151M&L Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:4) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including use and waste form work complete all as specified & directed.
152M & L provn for Green Marble work 18 to 20mm thick(table rubbed and polished,) in steps, window jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and as directed.
153Dismantling unframed timber scantlings 40 sq. cm & over in section, in any position complete all as specified and directed.
154S&F Rolled mild steel sections in roof trusses (framed), trussed,purlin,crane gantries,rails and fastenings and heavy bracket framing (beams,tee,angle,channel or flat sections) including distance pieces,cleats etc (welded/reviting) confirming to Fe 410 -W Gde E-250 Quality 'A' complete all as specified and directed
155S&F structural steel work as in tubular trusses ,purlin,rafters including special shaped washer complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.
156S&F rolled mild steel Plates (plain or chequered) channels. Square cut or notched (ordinary & counter sunk) forming holes, with riveted, bolted or welded attachment Gde Fe 410-O or Fe 310-O complete all as specified and directed
157S&F Mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5 Cm long and dia of shank 5 to 10mm complete all as specified and directed.
158Dismantling of Asbestos cement (corrugated, semi corrugated, ec) sheets roofing complete all as specified.
159S&F pre-coated galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa AZ150 crimping sheet at end as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.
160S&F 0.50 mm thick galvalume sheet pre-coated coloured for ridge or fixing for closing gable truss suitable for profile pattern sheet fixed with self driving screws complete all as specified & directed.
161Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness and any description, including cover fillets etc, complete all as specified.
162Supply and fix 600mmx600mmx4mm thick 'E' Board Classic ,Design Lake & hill as in false ceiling including supply and fixing GI 'Tee\\" grid frame work made of special section of M.S galvanized sheet 0.30mm thick , bottom portion painted with cellular nitro painting, warping the suspending wire around the existing wooden/steel purlin /rafter for suspending grid frame work of size 605mmx605mm suspended with 4 mm dia GI wire @ 1200mm c/c on main Tee and fixed to T-grid with the help of level clip or as per manufacturer direction. The section consisting of main Tee 37mmx24mmx0.60mm, cross runner tee 37mmx24mmx0.60mm and perimeter angle of 24mmx24mmx0.50mm thick. Perimeter angle to be fixed to wall with GI screw of 40mm long @ 450 mm c/c along the perimeter of wall including applying two coats of distemper oil emulsion complete all as specified and directed
163Excavating in post holes (or similar holes) each n exc 0.50 Cum in hard/dense soil, getting out and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified.
164M & L PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation, filling, mass concrete, sub-floors, floors etc all as specified
165S&F mild steel Angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire , etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling bolting or riveting, etc, and similar work conforming to Fe-290 Gde E-165
166S&F Mild steel Round bars 12mm dia and over, cut to length, bent to shape required, includinig cranking, bending spirally for hooping of columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips quality confirming to Fe-410 W
167S&F mild steel screw bolts (machine made) with hexagonal or sguare heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or screw nut n.exc 10 cm long dia of shank 12 mm complete all as specified.
168Supply and Fixing chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified.
169M&L preparation of newly steel surfaces over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat primer complete all as specified and directed.
170M&L PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in coping, benching to hold to lower portion of chain-link fencing, benching, floors and the like, including weathering, slightly rounded or chamfered angles and throating, including form work, complete all as specified and directed.
171Surface excavation not exceeding 30cm deep and average 15cm deep and getting out in soft/loose soil all as specified and as directed.
172M&L precast cement concrete coloured glazed interlocking tiles 60mm thick in floor/pavement laid over 20 to 30mm thick stone dust/sand cushioning laid dry to the profile all as directed by Engineer-in-Charge
173Dismantling of barbed wire of any thickness or size.
174M &L for hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified & directed.
175MS Flats for supports or stays for chain link fencing and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.
176Supply only Chain link fencing incl line wires, any mesh, size and type to any standarards, rails straining bolts etc incl provn of binding wire.
177Fixing of Chain link fencing incl line wires, any mesh, size and type to any standarards, rails straining bolts etc incl provn of binding wire. Note : Supply only chain link fencing and line wire will be measeured and paid separetly.
178S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers and one hexagonal or square nuts, exc 5cm and n.exc 10cm complete.
179S&F Mild steel round bars 10mm dia and over as in strengthening bars for bending cranking spiralit for hooking for chain link, hooking end and welding with flats of chain link fencing FE-290 (Gde E-165)complete all as specified .
180M&L for preparation of new iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer
181M & L Surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint
182S&F framed work (ornamental) as in steel gate of angle or other section with gusset plate ,rails braces etc complete drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hook and hinges and also fastening and fixing complete. of Fe -290(Gde E-165) complete all as specified and directed
183Dismantling of wrought iron or mild steel work of any description not other wise provided for complete all as specified and directed.
184Dismantling posts or struts (wood,steel or RCC ) in natural ground any section, including taking out embedded portion and making good disturbed ground etc all as specified. Note:post hole excavation not measured seperatly and making good old post hole and use the same complete all as specified and directed.
185Taking down copper/aluminium point wiring (light fan, socket or power) complete including fittings such as switch, sockets, c/rose, lamp holders, tube light fittings, sketch fitting , wooden boards, bell push, call bell, MCBs & regulators etc & making good to disturbed surfaces & matching with the existing colour of wall floor etc complete all as specified and directed.
186Taking down main switch, DB/change over/VTPN, MCCB AC box of any capacity complete all as specified and directed.
187M&L for concealed point wiring with 1.5 Sqmm PVC-FRLSH insulated, sheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit, including modular metal flush boxes & modular white cover plate with frame as per site requirement all fittings such as tees, bends, elbows, etc. of External diameter 20mm all as per site requirements PVC insulated & sheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead complete all as specified and directed by Engr-in-charge.
188For one light, fan point controlled by one switch
189For one call bell point controlled by one push button switch.
190For one 5 Amp independent socket point controlled by one switch
191For one 3 pin ,5 Amp socket point with other switch on the same board
192For one light, point controlled by two way switch
193M&L for concealed point wiring with 1.5 Sqmm PVC-FRLSH insulated, sheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit, including modular metal flush boxes & modular white cover plate with frame as per site requirement all fittings such as tees, bends, elbows, etc. of External diameter 20mm all as per site requirements but for power point wiring using with 2.5 sqmm PVC-FR LSH insulated ,sheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,sheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and directed by engir in charge.
194S&F Modular switch, one way, 6 Amp 230V, 1 module.
195S&F Modular switch, two way, 6 Amp 230V, 1 module.
196S&F socket Modular 6 Amp-2/3 pin combined 2 module.
197S&F switch Modular, single pole, one way,16 Amp ,1 module 230 Volt.
198S&F socket modular 6/16 Amp, 2/3 pin combined ,2 module 230 Volt .
199S&F ceiling rose, surface backlite,three terminal.
200S&F Modular lamp holder insulated with back plate suitable for Angle/Batten fitting.
201S&F modular fan step regulator 60-80 W, 2 module.
202S&F modular bell push 6A ,1 module.
203S&F call bell ding dong 230 Volt , single phase.
204Supply and fixing 6-40 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.
205S&F testing and commissioning of MCB SP 63 Amp 240 Volt 10 KA C-curve characteristics connected with suitable lugs complete all as specified and directed.
206Supply and fixing SPN 63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.
207S&F sheet metal enclosure DB double door, IP-43 when MCBs to be used SPN, 8 way, 240 V with 200 Amps rated bus bar of suitable size complete all as specified and directed.
208S&F double door metallic sheet metal enclosure DB double door VTPN of approved make suitable for housing 100 MCCB as incomer 4 Way 415 Volts with 200 Amps rated bus bars complete all as specified and directed.
209S&F MCCB 100 Amps 4 pole, suitable for 415 V breaking capacity 16 KA connected in wall/surface with wire and lugs all as specified and directed.
210S&F PVC 3M combination box of approved make with 16A socket heavy duty plug top and MCB SP 25 Amps flush mounting enclosure complete all as directed by Engineer-in-Charge.
211M&L LED TL fitting 20/18 watt for surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver long life corresion resistance impact proof surface mounting IP66 Lumanires PC housing in opeal finish coverwith high brighness complete all as specified and directed.
212M&L for provn of Earthing complete with galvanised steel earth plate electrode, 600x600x6mm buried directly in ground (Earth pit not less than 2.25M deep below the GL) with top edge not less than 1.5 metres below ground level connected with galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel all as shown in electric plate no 3 connected to earthing test point all as specified or indicated including testing on completion.Note :- (i) The rate quoted shall also deemed to include the cost of GI wire and protection pipe upto 7.5 Mtr beyond the earth plates electrode and also the cost of the Test point. (ii) Joining of GI earth wire with pipe of the test point shall be done by using suitable cable lugs complete all as specified and directed.
213S&F LED Bulk head fitting 13/10 watt designed for modern homes availave in PIR as well as non PIR sensor with premium quality diffuser for glarefree light and easy to install snapfit installer all as specified and directed by engir in charge complete all as specified and directed.
214Taking down fan ,sealing cable end,dismantling blades and removing fan and blades and deposited to MES store yard complete all as directed by Engr-in-Charge.
215Taking down and refixing connecting electric meter SP up to 60 amp incl S & F suitable board close recessed type of suitable size complete all as specified and directed.
216M&L for concealed sub main wiring with 2 single core PVC insulated FRLSH, sheathed copper conductor stranded 1100 volt grade cable of size 4 sqmm drawn in and incl PVC rigid conduit medium grade of size not less than 20 mm dia ISI marked ivory white with all accessories such as tee, bend, joint cover etc PVC insulated, sheathed copper conductor stranded 1100 volt grade cable of size 4 sqmm cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green complete all as specified and directed.
217M&L for concealed sub main wiring with 2 single core PVC insulated FRLSH, sheathed copper conductor stranded 1100 volt grade cable of size 6 sqmm drawn in and incl PVC rigid conduit medium grade of size not less than 20 mm dia ISI marked ivory white with all accessories such as tee, bend, joint cover etc PVC insulated, sheathed copper conductor stranded 1100 volt grade cable of size 10 sqmm cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green
218S&F box type LED optic fitting 1x9 Watt 2 feet box type of approved make complete as specified and directed by Engr -in -Charge .
219Taking down Repairs/servicing of old existing exhaust fan of any size and Refixing complete after repair all as specified and directed.
220Taking down and refixing after repair of electric water heater (25/50 Ltr Geyser) including electric connection lead of suitable size and length and all accessories, grouting of nut bolt/fastner on wall and making good disturbed surface complete all as specified and directed.
221S&F LED bulb inverter based rechargeable 12 watt suitable for angle / batten holder fitting.
222Supply and fixing copper wounded ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value greater or equal to 6.00 BEE Five star rated with brushless direct current motor (BLDC).
223Taking out old Bldg Security Light and Supply and fixing LED bldg security Light fixture with IP-66 protected die-cast aluminium housing and heat resistive toughened glass. LED shall be having LM-79 and LM-80 complied as per L-70 standard with 5700K CCT. Maximum power consumption shall not exceed 45W. Optics shall be properly designed with Polycarbonate Lenses to avoid dark patches on the road. Street light without lenses will not be acceptable. Note: (i) The item rate shall deem to provision of weather proof PVC insulated aluminium conductor cable 2.5 Sqmm, 2 core as required.
224M&L for GI pipe bracket of size 40 mm dia medium grade of length not less than 1.5 Mtr long and bent to a shape incl fixing on pole / wall with 02 Nos MS flate clamp of suitable size incl nut bolt and washers complete all as specified and as directed.
225Taking down old service cable and Supply and laying cable XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade cross sectional area 35 sqmm 3.5 core complete all as specified and directed.
226Excavation in trenches in any type of soil, including getting out hard / dense soil, not exceeding 1.5 m wide and not exceeding 1.5 m in depth, for laying of cable as the case may be, and getting out.
227M&L for sand cushioning in trenches for the cable etc all as directed by Engr-in-charge.
228Returning filling in with excavated soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.
229Removing excavated surplus material / soil not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.
230Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm complete all as specified and directed.
231S&F in replacement of GI Pipe light grade 50 mm dia ISI marked on pole on wall or laid in trenches incl all fittings (nut, bolt, clamps & washers)
232M&L for GI tubing of size 50mm bore, medium grade ISI marked with all GI fittings (medium grade) incl laid in trenches, floor etc complete all as specified and directed
233M&L for GI tubing of size 25mm bore, medium grade ISI marked with all GI fittings (medium grade) incl laid in trenches, floor etc complete all as specified and directed
234M&L for gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed of size 25 mm for iron pipe approved all as specified and directed.
235M& L for screwing existing steel tubing for alteration or additions or lengthening screw on pipe to form conectors of any size GI tubing all as specified and directed
236M&L for rendering 15 mm thick on brick work or stone masonry surface in CM 1:6 and finished even and smooth without using extra cement complete all as specified and directed.
237M&L for precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slab of manhole set in cement mortar 1:4 including demolition of existing broken cover slabs complete all as specified and directed.
238Excavation in trenches n exc 1.5 m wide n exc 1.5 m deep in soft/ loose soil for foundation etc or for shaft, wells, manholes etc n exc 10 Sqm on plan and not exc 1.5 m in depth and getting out. complete all as specified and directed.
239Demolition and breaking up drain pipes (salt glazed ware)/ RCC pipe etc set in cement mortar, 150 mm dia pipe complete all as per specification and directed.
240S&F HDPE double wall corrugated sewage pipe of 150 mm internal bore, SN-8, ISI marked as per IS 16908 Part-II-2013 laid in trenches, jointed and tested as per manufacturer instruction complete all as specifed and directed.
241M & L concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 (using 40mm graged stone aggregtaes) for 150mm mm dia pipe work in foul position complete all as specified & directed.
242Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-I smooth finished, and reforming benching as required(Internal dia of pipe 150mm) complete all as specified & directed. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58340060
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 3.39 Crore
LAST DATE 01-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender for Additional / Alteration And Special Repairs To Selected Officers Married Accommodation At Saugor Military Station
Basic Detail
Tender No CEBZ/SAG/TOKEN/27 OF 2026-27
Bidding Type Tender
Location
City Sagar
State Madhya Pradesh
Key Dates
Publish Date 02 Nov 2026
Submission Date 01 Dec 2026
Open Date 03 Dec 2026
Finance
Tender Value 3.39 Crore
Tender Fee 2000
EMD 4.15 Lakhs
Exemption Not Available
Document List
acab89a9-6fbd-4197-8217-e81b4817cf2f.html
BOQ_892831.xls
SR04TenderDocuments.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 02, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 01, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 9 days
Dec 03, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 11 days

Tender Documents

Download All (ZIP) ↓
html

acab89a9-6fbd-4197-8217-e81b4817cf2f.html

xls

BOQ_892831.xls

pdf

SR04TenderDocuments.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender