Defence Statutory Bodies & Commissions/Committees Closing in 6 days TDR #58338848

Tender For Special Repair Bldg No P-47 (Or Govt Md Accn) At Sect A At Dinjan Mil Stn Under Ge Dinjan

Issued by Statutory Bodies & Commissions/Committees · Tinsukia, Assam
Tender Value
61 Lakhs
Estimated cost
Bid Submission
28 Nov 2026
6 days left
EMD
1.16 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Tinsukia → Assam
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Special Repair Bldg No P-47 (Or Govt Md Accn) At Sect A At Dinjan Mil Stn Under Ge Dinjan

Corrigendum

Sr No Corrigendum Date Corrigendum Type New Submission Date
1 13-Nov-2026 AMENDMENT Other 28-Nov-2026

BOQ

Name of Work:- SPL REPAIR BLDG NO P-47 (OR GOVT MD ACCN) AT SECT A AT DINJAN MIL STN UNDER GE DINJAN
Sl. No. Item Description
1Demolition of cement concrete in ground floor n exc 15 cm thick (un reinforced) complete all as specified and directed.
2M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in chajjas top, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over top of chajja complete all as specified& directed by Engr-in-Charge.
3Dismantling of plain or corrugated sheeting all as specified.
4S & F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.
5S&F Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified.
6M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.
7Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as directed.
8S & F Mild steel Galvlume sheet sheet eaves gutters, galvanised class 3, half round with rounded edges of thickness 1.25mm of dia 150mm complete all as specified & as directed.
9S&F 0.71 mm thick Plain Aluminium sheeting alloy 31000H4 in ridges, hip, crumple joint etc. complete all as specified and directed.
10Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets as directed.
11S & F of Weather boarding, clean sawn, thickness 20mm to 25 mm of Hardwood second class and rebated on thick edge to give 20mm laps and fixed
12S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing two coats of white wash complete all as specified and as directed.
13Dismantling wrought iron or mild steel work of any description not otherwise provided for.
14Taking down chowkats or frame, n. exc 1.5 sqm each with shutters (without taking off shutter from the frame) as directed.
15Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exe 1.50 & n.exc. 4 sqm in each complete all as specified & directed.
16M&L PCC 1:3:6, C-1 (using 20 mm graded stone aggregate) as in bed blocks for inserting holdfast/ filling of steel frame, etc including necessary form work complete as specified and directed.
17S&F solid PVC moulded door frame of size 50mmx47mm made out of 5mm, single side prelam PVC sheet used and edges will be painted to match with printed to match with prelam sheet, reinforced with MS square tube & fixing in opening including hold fast.
18S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and directed.
19S&F pressed steell door frame 105x60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates comlete as specified and directed (pcc filling of holloow section measured and paid seprately)
20S&F pressed steell door frame 125x60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates comlete as specified and directed (pcc filling of holloow section measured and paid seprately)
21S & F of Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N(Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately
22Refixing only of 35mm thick factory made, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a).
23S & F 35mm thick factory made, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a).
24S&F powder coated aluminium anodised frame for doors, windows etc with one or more rebates including joining cleat for fixing etc complete all as specified and directed.
25S&F Anodised aluminium powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including all necessary fittings like hinges joining cleats, glazing clips,moving roller, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified
26Supply and fixing of aluminium sliding window with powder coating (minium thickness of powder coating 50 micron) including following components / specification complete all as specified and directed. (i) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (ii) All vercal/ horizontal joint shall be of extruded aluminium section so as to avoid any play between jointed members. (iii) all other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, srews, etc. (iv) Stainless steel wire cloth, 036 mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples, etc. (v) Sheet glass 4 mm thick selected quality tinted/black glass and glazing with oil putty or fixed with wooden beads in square not exceeding 0.5 Sqm in each pane (vi) Rest all as specified in drawing no CEZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5, 5R/5. Note :- Grill shall be measured and paid separately.
27S &F Sheet glass, 5mm thick frosted glass ordinary quality and glazing with oil putty in Square n exc 0.5 sq. m in each pane
28S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.
29Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 18mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)
30S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in shelves of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel L Shaped brackets which should with hold as average weight of 20-30 kg and fixed with ecessary fully body threaded star headed counter sunk S.S screw, all as per direction of Engineer In- Charge
31M & L MS flat iron work as in hold fast and similar small articles, cut to length, bent to shape, drilled hole and fixed with screw etc conforming to Fe-290 Gde-E-165 complete as specified and directed.
32M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165
33S & F in repair Wire netting of stainless steel wire 1.4mm dia and 12mm Size of mesh is fixed with tinned tacks of stainless steel wire staples complete as specified and directed.
34S&F 100mm size stainless steel butt hinges medium weight cold rolled.
35S & F Width of flaps (when open) 40mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified & directed by Engr-in-Charge.
36Supply and fix for 100mm long aluminium /stainless steel handles, cast type, anodised complete all as specified and as directed.
37Supply and fix for 150mm long aluminium/stainless steel handles, cast type, anodised complete all as specified and as directed.
38Supply and fix in for 150mm long aluminium /stainless steel anodized barrel tower bolts of extruded section complete all as specified and as directed.
39Supply and fix in for 200mm long aluminium /stainless steel anodized barrel tower bolts of extruded section complete all as specified and as directed.
40Supply and fix 250mm long Aluminium alloy/stainless steel, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.
41Supply and fix 300mm long Aluminium alloy/stainless steel, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.
42S&F in Repair Floor door stopper of aluminium alloy /stainless steel, body and tongue, anodised, with hard drawn steel spring, fixed in floor
43S&F door seal aluminium rod withnylon brush of approved colour fixed to shutter with and incl 20mm steel wooden screw complete all as specified and directed
44S & F in repairs curtain rails, harrison rail, aluminium alloy chromium plated with fixing brackets, stops, rollers etc.
45M & L preparation of new untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete as specified and directed.
46M & L preparation of old wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint complete as specified and directed.
47Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre peri linear metre including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement : 2 Coarse sand) to match the existing floors drilling and plugging holes etc complete all as specified and as directed.
48M & L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors
49Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises as directed.
50M & L 25 mm thick PCC type B0 1:2:4 (using 12.5 mm graded stone aggregate) as in leveling all as specified and directed.
51M&L for ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:4) for laying of floor finishes complete all as specified and directed.
52M&L for ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed.
53M&L Non skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm 7mm thick coloured tiles in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over screed bedding 15mm thick in CM 1:4 as specified and as directed.
54M&L for glazed ceramic tiles in vertical surface 300x450x7mm thick in dado over 10mm thick screed bed in CM 1:4 on walls set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed
55Dismantling of stone slabs or tiles of any description or thickness as in floors, pavings, aprons, pathway etc laid dry or laid dry and pointed complete all as specified & directed.
56Material and labour for Machine cut kota stone slab flooring 20 to 25mm thick size not less than 22\\" x 22\\" laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 20mm thick cement screed bed in cement mortar 1:3 including rubbing and mirror polishing complete all as specified and as directed.
57Material and labour for kota stone slab 20 to 25mm thick in riser of steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick rendering in cement mortar 1:4 including cutting, moulding outer edges, rubbing and mirror polishing complete all as specified and as directed.
58M&L for 20mm thick granite (of any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixure of pigment to match the shade of granite complete all as specified and directed.
59M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.
60M&L for cutting holes in stone /RCC/granite slab for inserting coocking gas cylinder pipe and making good complete all as directed
61M& L Chequered cement concrete tiles 25cm x 25cm x 20mm thick set, jointed and pointed in neat cementsluny in floors over 15mm thick screed beb in Cm 1:6 complete all as spercified and directed.
62M & L 75 mm thick PCC type D-2 1:4:8 ( using 40mm graded stone aggregate) as in sub base all as specified and directed.
63Demolition of Brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles.
64Material & Labour for Brick work with sub class ‘B’ old size bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) complete all as specified.
65M&L for half thick brick work with sub class \\"B\\" bricks straight or curved on plan exceeding 6m mean radius with old size bricks locaaly available built in cement mortar 1:4 complete.
66Taking down cement plaster on brick walls/ concrete surface, etc. including raking out joints, hacking for key, scrubbing down with water, etc.
67M&L 15 mm thick cement plaster in CM (1:4) on wall ( with approved water proofing compound) on fair faces of brick work incl finished even and smooth without using extra cement.Note: 1. WPC @ 2% of cement, will be paid separately.2. The rate quoted by contractor is deemed to be included necessary scaffolding and formwork as required upto 7.00 Mtr height building.
68M&L for preparation of new plastered surface of wall Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 1mm thick plaster of paris putty on new surfaces complete all as directed
69M&L for complete removal of existing treatment inclpreparation of old surfaces, scrubing down, washing etc from walls by scrapping with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7\\"/9\\" to make the surface free from dust, loose paint etc. and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted) with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfacesincl 1mm thick plaster of paris putty, using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and will execute the same work by authorised applicator as mentioned in PS and acessories complete all as specified and directed.
70M&L 15 mm thick cement plaster on wall in CM (1:6) on fair faces of brick work incl finished even and smooth without using extra cement.
71M&L for preparation of newly plastered surfaces of walls & applying two coat of distemper oil emulsion over 1mm thick wall care putty birla white or JK & over one coat of chalk whiting priming paint complete.
72M & L for complete removal of existing treatment of wall and applying two coats of oil bound distemper over 1mm to 1.5 mm thick wall care putty of birla white or K & primer completely
73M&L 5 mm thick cement plaster in CM (1:3) on ceiling surfaces incl finished the surface even and smooth without using extra cement.
74M&L for Preparation of new plastered surfaces and applying three coat of white wash on ceiling complete all as specified.
75M&L preapring old plastered surfaces incl washing rubbing down and stopping of distempered and painted surface of ceiling and applying two coat of white wash complete as specified.
76Supply only Integral water proofing compound
77M&L for applying two coat of Synthetic enamal paint over a coat of red oxide primer on new steel based surfaces exc.10cm width or girth including preparation all as specified and directed.
78M&L for applying two coat of Synthetic enamal paint on pre primed steel based surfaces exc.10cm width or girth including preparation all as specified and directed.
79M&L for 75 mm thick plain cement concrete (1:3:6) Type C2 using 40 mm graded aggregates as in plinth protection/paving including finishing surface even and fair without using extra cement complete all as specified and directed
80Forming Construction joint 30mm deep x 10mm wide filled with sealing compound, Grade ‘A’
81Providing precast cement concrete Type C0 (1:3:6) 12.50 mm graded aggregate as in louvres and jallies, 25mm thick (measured solid), including all mould- ings but excluding frame complete all as specified and directed.
82M& L for Taking down plastering on roof surfaces upto slb level including padding/ mebaranes in cement mortar (one side only measured in cases where both sides are plastered) and Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified & directed by Engr-in-charge
83M&L for water proofing treatment by the authorized rep of OEM on RCC roof and parapet wall etc. comprising with the following operation & as specified herein below:- (a) Surface Preparation: Surface preparation of new RCC roof slab including ensuring completion of all civil works, cleaning of surface to make it sound, level and free from dust, laitance, oil, grease and other contaminants by wire brushing, grinding and air blowing, removing all loose particles and protrusions, repairing minor honeycombs / surface defects with polymer modified mortar, sealing tie-rod holes and openings with non-shrink grout, and ensuring surface is dry and suitable for application of waterproofing system. (b) Bore Packing for Overflow / Drain Pipes / Pipe Penetrations: Preparing the inner surface of core opening and external surface of PVC / MS pipe by roughening using emery paper / sand paper to remove smooth finish and to ensure proper mechanical bonding. Cleaning the surfaces by wire brushing and water jetting to remove laitance, dust, loose particles and other contaminants. Providing necessary shuttering / formwork arrangement as required to carry out bore packing depending upon site conditions. Applying a coat of polymer bonding slurry mixed with cement to enhance adhesion between old concrete, pipe surface and packing material. Packing the annular gap between pipe and concrete using non-shrink cementitious, polymer modified grout / micro-concrete up to the finished surface level while the bonding coat is in tacky condition, complete to obtain watertight sealing. (c) Coving 75×75 mm — Providing and laying 75×75 mm cement‑sand coving in internal corners in 1:3 mix, modified with SBR latex, including surface preparation, mixing, laying, finishing smooth, curing, and all labour, materials, tools and tackles complete as per specification.
84(d) Moisture Insensitive Epoxy Primer: Providing and applying moisture-insensitive two component epoxy primer on the prepared concrete surface at a coverage rate of approximately 300 g/m², depending upon substrate porosity and surface condition, to ensure proper penetration, surface sealing, and to achieve strong adhesion between the concrete substrate and the subsequent polyurethane waterproofing membrane. Primers shall be suitable for application on substrates having moisture content up to 12% visibly dry, applied uniformly on clean, sound, and properly prepared surface in accordance with manufacturer’s specifications. (e) Application of single Component PU Waterproofing Coating: Providing and applying two component polyurethane waterproofing membrane to achieve seamless and continuous waterproofing system with minimum total dry film thickness of 1.5 mm. The membrane shall be applied on prepared substrate and extended vertically on parapet wall up to a minimum height of 300 mm from finished surface level. At the termination point, a suitable groove shall be cut in the parapet wall and the membrane shall be properly tucked inside the groove and sealed with polymer modified repair mortar to secure the termination and ensure watertightness. The material shall have the following minimum properties: A. Solid Content ≥ 90% as per ASTM C836 B. Tensile Strength ≥ 6 MPa as per ASTM D412 C. Elongation = 600 ± 50% as per ASTM D412 D. Shore A Hardness = 70 as per ASTM D2240
85(f) Providing and laying non-woven geotextile protection layer over horizontal surface of minimum 150 GSM over fully cured polyurethane waterproofing membrane, to protect the membrane from mechanical damage during subsequent construction activities. Care shall be taken to ensure that the protection layer remains in position during protection screed.(g) Carrying out a 48-hour ponding test after completion and rectifying any defects.The rate shall include all materials, labour, T&P, scaffolding, surface preparation, transportation, loading, unloading and all incidental charges complete.Notes:1 Rates for removal of APP and screed bed items including WPC shall be measured and paid seperately.2 MOU with OEM shlall be submitted by the contractor for 10 years of warranrty towards the water proofing treatment by the OEM/ authorized applicator of OEM
86M &L for providing screed bed of 15 mm thick with cement motar 1:4 for laying of floor finishes over 25mm PCC after PU water proofing treatment as specifiedand directed
87M&L for special treatment for sunken portion of WCs/Bath & toilet executed in following stage:- Stage1:- Demolition of wc including lime concrete and cemennt concrete etc and preparing of surfaces of existing sunken portion of wc`s or bath etc with wire brush to removed all loose dirts, oil grease etc including removing debries from site of work etc. Stage 2:- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per manufacturere`s instructions. Stage 3:- Apply Dr. Fixit Premeseal primer or equivelent of STP Ltd (and allow to dry for 8 hrs) all as per manufacturer`s instructions. Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 micron or shilicry 215 of STP (The surfaces after painting one coats shall be allowed to dry for 6 hrs before next coats) Stage 5:- Rendering 10mm thick in CM 1:3 mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per manufacturere`s instructions. Stage 6:- All CI joints shall be filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr. Fixit pidicrete URP all as per manufacturer`s instructions. Stage 7:- Making holes in walls and fixing 600mm long 40mm dia medium grade GI spouts for draining of excess water if any. Stage 8:- Carryout ponding testfor 48 hrs to ensure water tighteness of repaired sunken portion and filling of sunken portion for cement concrete Type E2, 1:5:10 using 40mm graded stone aggregate as in lean concrete complete all as specified and directed. Note:- only plan area shall be measured for payment under this items. (b) Depth of suken portion of WC`s/ bath shall be upto 35 CM which is to be taken into account while coating the rate against this item. (c) The rate shall be quoted by contractor shall be deemed to be included for all the horizontal and verticl treated surface of sunken portion of WC`s/baths.
88Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.
89Material and labour for RCC (1:2:4) type B-1 (using 20 mm graded broken stone aggregate) as in slab supported on walls, beams and column in floors, roof landings, balconies, canopies, deck slabs and in shelves complete all as specified and as directed. (Note : Reinforcement shall be measured and paid seperately under relevant)
90Material and labour TMT bar 10 mm and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and as directed.
91Use and waste formwork to soffits of suspended slabs such as roof slab, floor slabs, landing covers, and similar works, for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm, complete all as specified and directed.
92Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.
93Supply and fix as in repairs rolled mild steel as in joist, channel, angle or tee section/hold fast/wind ties fixed independently with connecting base plate etc complete all as specified and as directed.
94Taking up or down 15mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed.
95S & F of CPVC pipes outer dia 16mm SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. 15 mm bore CPVC tubings 'medium grade' with all fittings & fixed complete to walls & ceilings or laid in floors complete all as specified and directed.
96Taking up or down 20mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed.
97S & F of CPVC pipes outer dia 20mm SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. 15 mm bore CPVC tubings 'medium grade' with all fittings & fixed complete to walls & ceilings or laid in floors complete all as specified and directed.
98Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good , cutting not exc 10cm girth complete all as directed.
99S & F as in repair for 600 x 450 mm bevelled edge mirror of selected qulity glass, mounted on 6 mm thick AC building boards of commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed.
100S & F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 485mm x 420mm bowl size 410mm x 330mm x 160mm
101S & F in repairs 15 mm bore Bip taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.
102S & F in repairs, stop valves, 15 mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions as specified and directed.
103S & F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends.
104S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges all as specified and as directed.
105S& F as repairs brass chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union 125 mm size complete all as specified and directed.
106S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.
107S&F in repair soap dish of stainless steel fixed to wall with chromium plated brass screws complete all as specified and as directed
108S&F in repairs flexible (coil shaped) PVC waste pipe for sink and wash hand basin 32/40mm dia, length not less than 80 cm, connected to PVC waste coupling/fittings complete all as specified and as directed.
109S & F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed.
110S & F in repairs Vitreous china wash basin, white,flat back, size 550 x 400 mm with brackets,excluding pillar cock 15 mm bore CP, PVC connection of 450 mm long including PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as specified and directed.
111S & F 15 mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe as specified.
112S & F vitreous china Semi pedestal pattern (Anglo Indian type) white connection to trap 'P' or 'S' and flush pipe etc including seat cover and making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing including taking down the existing old one all as specified and as directed.
113S & F in repairs mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete.
114Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water tanks complete as specified in SSR Part-I
115S & F 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms)
116S&F as in repairs for Gun metal gate valves with iron wheel headscrewed both ends for iron pipes or for unions for 20 mm bore pipes, complete all as specified.
117Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement and similar work complete all as specified and as directed.
118S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete.
119S&F wall mounted Modern kitchen Utensils Dish Rack Stainless steel (31X10X30 inches) all as specified and directed.
120M& L for PVC (SWR) floor trap 100 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified.
121M& L for PVC (SWR) floor trap 75 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified.
122Demolition and breaking up 150 mm bore drain pipes, salt glazed stone ware set in cement mortar including PCC haunching and bedding, complete.
123S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified.
124M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.
125M&L for cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe.
126S&F for 50mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 5 ton/Sqm in square, rectangular shape of size 300X300, 450X450, 600X600 complete all as specified & as directed.
127S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified including dismantling of PCC & taking out old unserviceable 110mm bore PVC pipe with fittings & making good disturbed area complete all as specified & directed.
128S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified including dismantling of PCC & taking out old unserviceable 75 mm bore PVC pipe with fittings & making good disturbed area complete all as specified & directed.
129S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 110mm bore pipes complete all as specified and directed.
130S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 75mm bore pipes complete all as specified and directed.
131S & F for PVC (SWR) bends any radius with access door, 110mm bore complete all as specified and directed.
132S & F for PVC (SWR) bends any radius, 110mm bore complete all as specified and directed.
133S & F for PVC (SWR) vent cowl, 110mm bore complete all as specified and directed.
134S & F for PVC (SWR) bends any radius with access door, 75mm bore complete all as specified and directed.
135S & F for PVC (SWR) bends any radius, 75mm bore complete all as specified and directed.
136S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed by Engr-in-Charge.
137Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge.
138Taking down carefully MCB DBs any type and size by unscrewing from main switch boards/cut out boxes and removing materials to store for keeping in safe custody for reuse at site or for taking credit including sealing the cable ends and making good disturbed surface of wall etc as per existing finishes complete all as specified and directed.
139Taking down ceiling fan/exhaust fan and removing fan and keeping it in MES store for safe custody and refix it after minor repair and paint. Please Enable Macros to View BoQ information
140Taking down ceiling fan/exhaust fan and removing fan and keeping it in MES store for safe custody and refix it after minor repair and paint. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58338848
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 61 Lakhs
LAST DATE 28-11-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Special Repair Bldg No P-47 (Or Govt Md Accn) At Sect A At Dinjan Mil Stn Under Ge Dinjan
Basic Detail
Tender No 84600/E8
Bidding Type Tender
Location
City Tinsukia
State Assam
Key Dates
Publish Date 13 Nov 2026
Submission Date 28 Nov 2026
Open Date 01 Jan 0001
Finance
Tender Value 61 Lakhs
Tender Fee 1000
EMD 1.16 Lakhs
Exemption Available
Document List
07764bbe-3ef3-4f7a-9200-287c4b7b4ed6.html
BOQ_893835.xls
TenderDocuments.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 13, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 28, 2026
18:00 IST

Corrigendum-1 Issued

Clarifications on tender conditions and amendments issued.

Upcoming · 6 days
Nov 28, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 6 days

Tender Documents

Download All (ZIP) ↓
html

07764bbe-3ef3-4f7a-9200-287c4b7b4ed6.html

xls

BOQ_893835.xls

pdf

TenderDocuments.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender