Bids Are invited for Special Repair Of Surveyed Off Condemned Furniture For The Qe Sep 2025 Under Ge Minniebay

Sharing tender

Bids Are invited for Almirah Large With Shelves Steel - Almirah Large With Shelves Steel. Overall Size Shall Be 1985Mm High,920Mm Wide And 485Mm Deep. The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Bases Made In U Shaped With Ends Covered . Mild Steel Sheet Shall Be 1Mm Thick. The Base Channel Shall Be Welded At 50Mm From Each End Of The Length Of 920Mm And Shall Be Up To Full Width Of 485Mm And Shall Be 100Mm High Top, Sides Bottom And Back Of Almirah Shall Be Of 1Mm Thick Mild Steel Sheet . Four Shelves Equally Spaced Of 1Mm Thick Mild Steel Sheet Shall Be Provided To Make Five Compartments.Front Shutter Shall Two Leaves Of Equal Size .Front Shutter Leaves Shall Have Three Butt Hinges Of 75Mm Fixed To Each Shutter And Shall Be Side Hung. All Joints And Welding And Fixing Shall Be Done In Accordance With The Standard Workmanship. One Chromium Plated Steel Handle With A Locking Device Shall Be Provided As Shown On Drawing . The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate. All Steel Surfaces Shall Be Painted With Two Coats Of Smoke Grey Paint Internally And Extrenally With Spray Machine Over A Coat Of Red Oxide (Primer)After Preparation Of Surfaces.A Mark Of Mes Shall Also Be Provided On Top Left Corner Of Front Shutter With Visible Colour. Painting Shall Be Done With Spray Machine.Rest All As Per Drg No Fd-1031 , Almirah Med With Shelves Steel - Almirah Med With Shelves Steel. Overall Size Shall Be 1270Mm High,765Mm Wide And 440Mm Deep. The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Base Welded To Bottom Of Almirah And Shall Be 100Mm High. Mild Steel Sheet Shall Be 1Mm Thick For Channel Base. The Base Channel Shall Be Welded At 50Mm From Each End Of 765Mm Length And Shall Be Up To Full Width Of 440Mm Of Almirah. Top, Sides, Back, Bottom And Front Of Almirah Shall Be Of 1Mm Thick Mild Steel Sheet. Three Shelves Equally Spaced Making Four Compartments Shall Be Provided And Shall Be Of 1Mm Thick Mild Steel Sheet.Front Shutters Shall Have Two Leaves.All Joints And Welding, Fixing Shall Be Done According Standard Workmanship. A Steel Chromium Plated Handle 100Mm Long Shall Be Provided To The Shutter. The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate . All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted With Two Coats Of Smoke Gray Colour Paint Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visible Colour As Directed By Engr-In -Charge. Rest All As Per Drgs No Fd-1032 , Locker Bed Side Steel - Locker Bed Side Steel. Overall Size Shall Be 760Mm Long, 600Mm Wide And 1100Mm High. The Locker Shall Be Made Of Mild Steel Sheet 1Mm Thick.20 Mm Dia Conduit Pipe Shall Be Chrome Plated With Wall Thickness Of 1.6 Mm Shall Be Fixed With Side Sockets.Two Handles Chromium Plated 100Mm Long Shall Be Fixed To Shutters With Necessary Riveting . One Hasp And Staple 75Mm Long Shall Also Be Fixed To Shutters With Riveting.The Left Shutters Shall Be Provided With 100Mm Long Tower Bolt Inside At Upper And Lower Ends Also.The Locker Shall Be Provided With Compartments As Shown In Drgs Made Of 1Mm Ms Sheet. All Steel Surface Internally And Externally, Exposed To View When Placed In Position Shall Be Given Two Coats Of Smoke Grey Paint Internally And Externally After Properly Smoothened The Surface With Sand Paper And Applying Putty. Painting Shall Be Done With Spray Machine. Rest All Specifications Are As Per Drg No Fd-1029 , Table Bed Side - Table Bed Side. The Overall Size Of The Table Bed Side Shall Be 450Mm X 450Mm X 600Mm From Rear And 450Mm X 450Mm X 500Mm From Front As Shown In Drg.The Entire Frame Of Table Bed Side Shall Be Made Up Of 18Mm Ms Square Pipe (18 Gauge) Duly Black Powder Coated. The Two Sides And Top Shall Be Made Up Of 18Mm Thick Mdf Board Exterior Grade. The Back Of The Table Except The Top Portion As Shown In Drg Shall Be Provided With 6Mm Commercial Plywood Bwr Grade Duly Screwed To Frame. The Two Sides, Back And Bottom Of Drawers Of The Table Shall Be Made Up Of 12Mm Thick Mdf Board Irrespective Of What Is Shown On Drg, Except The Front Side Which Shall Be Of 18Mm Thick Mdf Board Exterior Grade. The Drawers Shall Be Made Functional By Using Telescopic Channel Of Appropriate Size ,Shall Be Used For Smaooth Mvement Of Drawer.The Drawers Of The Tables Shall Be Provided With 100Mm Long Cp Handles .Rest All As Per Drg. The Lower Portion Of The Bed Side Table Should Be Box Type Provided With One Shutter Of Appropriate Size Duly Fixed With Piano Type Hinges, One Cp Handle Of 4 Inch Size And One Magnetic Catcher Should Also Be Provided. Rest All As Shown On Drawing And As Directed By Engr-In-Charge. Drg No Fd/E6/Map/15(R) , Bed Hard With Ply Top - Bed Hard With Ply Top. Overall Size Shall Be 2050Mm Long, 900Mm Wide And 400Mm High. All Steel Shall Be Ms Square Pipe Of 18 Gauge. The Head Board Shall Be 800Mm High And Foot Board Shall Be 500Mm High. The Frame Of Head Board And Foot Board Shall Be Of 38Mmx38mm Ms Square Pipe.18Mmx18mm Ms Square Pipe Shall Be Provided In The Inner Of Head Board Frame/Foot Board Frame As Shown In Drg.18Mm Thick Both Side Decorative Mdf Board Exterior Grade Of Walnut Shade With Pvc Edging Shall Be Screwed To Ms Strip Arc Welded To 18Mm Thick Rectangular Pipe With Standard Workmanship Both In Head Board/Foot Board. 25Mmx65mm Rectangular Cr Pipe Shall Be Used To Make The Long Rails And Short Rails Of Bed Hard And Welding Shall Be Done For Fixing Long Rails To The Legs Irrespective Of What Is Shown On Drg.One Stiffener Of Size 25Mmx25mm Shall Be Welded Between The Two Legs Of Headboard Over 150Mm From The Ground Level. The Top Of Bed Hard Shall Be Of 12Mm Thick Bwp Ply With Anititermide Of Approved Make Fixed Over The Four Equidistant Stiffener Of Size 25Mmx25mm Sq Ms Pipe In Line With Bottom Of 25X65mm Long Rail Section. Pvc Shoes Shall Be Provided To Legs Of Bed.All Metal /Iron Work Shall Be Painted With Synthetic Enamel Black After Doing Two Coats Of Metal Primer.Rest All As Per Drg No Fd/E6/Map/08 (R) , Charpoy Ip With Hard Top - Charpoy Ip With Hard Top. Overall Size Shall Be 1980Mm Long, 900Mm Wide And 440Mm High. Two Long Rails And Two Short Rails Shall Be Of 25Mmx65mmx16 Gauge Ms Rectangular Pipe .The Legs Shall Be Of Size 32Mmx32mmx16 Gauge Welded To Long And Short Rails As Shown On Drg.Two Stiffeners Of Size 25Mmx25mmx16 Gauge Shall Be Provided In Equidistant Between Two Opposite Long Rails. Six Number Cleat Of Size 25Mmx60mmx6mm Shall Be Welded With Frame To Support Ply. Two Stiffeners Joining Legs Of Size 25Mmx25mmx16 Gauge Shall Be Provided At 150Mm From Ground Level 12Mm Thick Bwp Plywood Shall Be Provided For Top As Shown On Drg With Proper Nut And Bolt .One Nut And Bolt Shall Also Be Provided At Centre Of Each Stiffeners For Fixing The Plywood Irrespective Of What Is Shown On Drg. Pvc Hard Rubber Shoes Shall Be Fixed At Bottom Of Each Leg. All Steel Surfaces Shall Be Painted With Synthetic Enamel Paint Black In Color After Applying A Coat Of Primer. Rest All As Per Drg No Fd/Map-Ii/01 , Chair Ornate With Arms - Chair Ornate With Arms. As Per Trade Pattern And Directed By Enginer-In-Charge. , Book Case Small - Book Case Small . Book Case Small - Overall Size Shall Be 1025Mm Long, 450Mm Wide And 750Mm High. Back Shall Be 1025 Mm Long And 750 Mm High Made Out Of Prelaminated Hdf Board Bd 18Mm Thick One Side Teak/Walnut And Other Side Balancing White, Rest All As Per Drg And As Directed By Engr-In-Charge.Fd - 237 , Table Writing Med - Table Writing Med. Overall Size Shall Be 1145Mm Long, 600Mm Wide And 760Mm High. All Wood Shall Be Of First Class Hard Teak Wood Except Top And Right Hand Side Drawer Cabinet. Legs Shall Be Of 35Mmx55mm In Section And 717Mm High Having 5Mmx5mm In Section Groove At The Top Of Legs At The Portion When Placed In Position. The Top Shall Be Of 18Mm Thick Prelaminated Hdf Board Of Approved Shade And The Edges Shall Be Covered With 4Mm Thick Teak Wood Beading. Two Short Stiffeners Of Teak Wood Of Size 50Mmx40mm In Section Irrespective Of What Is Shown On Drg Shall Be Provided Between Legs At 100Mm From Bottom Of Legs. Sides Of The Box Which House The Drawer And Cabinet Shall Be 18Mm Thick Bwp Grade Plywood Sides And Back Of Drawers Shall Be Of 12Mm Thick Teak Wood Planks. Bottom Of Drawers Shall Be Of 6 Mm Thick Plywood Bwp Grade.6Mm Thick Plywood Bwp Grade 75Mm High Partition Shall Be Provided In The Drawer. Shutter For Cabinet Shall Be Fixed With Piano Type Continuous Hinges. Lock Shall Be Provided To Drawer And Shutters. Recessed Handle Shall Be Provided To Drawer And Shutter.25Mm Dia And 25Mm High Rubber Shoes Shall Be Fixed To Bottom Of Legs. All Wood Surfaces Shall Be Melamyne Polished With High Gloss Finish By Spray Machine. Rest All As Per Drg No Fd-275 , Table 3 Feet X2 Feet Without Drawer - Table 3 Feet X2 Feet Without Drawer. All As Shown On Drawing. Overall Size Shall Be 900Mm Long, 600Mm Wide And 760Mm High. All Wood Shall Be Of First Class Hard Wood Leak (Mp). Legs Shall Be Of 60Mm X 30Mm In Section Throughout And 741 Mm High, Four In Numbers Joined Together In Front, Back And Sides With Top Rails 20Mm X 60Mm In Section Provided Flush With Top Of Legs. At Bottom, 100Mm High From Bottom, Side Wooden Lower Rails Of 20Mm X 60Mm In Section Shall Be Provided In Short Sides Joining Legs In Short Sides. 5Mm X 5Mm In Section Groove Shall Be Provided In Legs At Top Of Legs In Portion Visible When Placed In Position. Table Top Shall Be Of 18 Mm Thick Prelaminted Hdf Board Exterior Grade. 4Mm Thick Teak Wood Edging Shall Be Provided All-Round The Edges Of Top Of Table. The Top Of Table Shall Be Flush With Legs And There Shall Be On Projection On Any Sides. All Wood Surfaces Exposed To View When Placed In Position Shall Be Melamyne Polished With High Gloss Finish. Hard Rubber/Pvc Shoes Of 25Mm Dia And 25Mm High Shall Be Screwed To Bottom Of All Legs. Drg No Fd-1009 , Chair Revolving Executive - Chair Revolving Executive. Glass Filled Nylon Backrest With Lumber Support & Mesh Fabric. 4D Adjustable Armrest With Gel Pu Pad. Self Weight Syncro Tilt Multi Position Lock And Seatslider. 700Mm Aluminium Diecast Base & 60Mm Nylone Twin Castors With Class 4 Gas Lift.Finrest Composite Leather On Seat & Back. Knee Tilt Mechnism With Multiposition Lock. As Per Trade Pattern Sample And As Directed By Enginer-In-Charge. , Table Centre - Table Centre. Overall Size Shall Be 1200 Mm, 600 Mm Wide And 400Mm High. Legs Shall Be Of 40 Mm Dia Anodized Brass, Four In Nimer In Pne Piece. The Les Shall Be Joined In Short And Long Sides With Two Numbers 25 Mm Dia Brass Pipe Of Wall Thick Ness 2 Mm. The Top Pipe Shall Be Fixed 150 Mm Form Top And Lower Pipe Shall Be At 100 Mm From Bottom Of Top Pipe The Brass Frame Shall Be 900 Mm Long And 450 Mm Width. Vaacuum Rubber Shoe Shall Be Provided At Top Of Legs. Which Shall Be Closed With Brass Sheet 1.6 Mm Thick. The Bottom Of Legs Shall Be Covered With Brass Sheet Of 1.6 Mm Thick Sheet. The Botyom Of Legs Shall Have Pvc Shoe. The Top Shall Be 10 Mm Thick Plate Tinted Glass ( Brown) Colour Corers Rounded As Shown In Drg, The Edges Of Top Of Table Shall Be Rounded Off. Drg No Fd-375 , Peg Table - Peg Table. Overall Size Shall Be 450Mm Long,300Mm Wide And 380Mm High. Legs Shall Be Of Teak Wood Of Section 30Mmx50mm.The Legs Shall Be 362Mm High.5Mmx5mm In Section Groove Shall Be Provided On The Top Of Legs Which Shall Be Visible When Placed In Position.Two Nos Top Rails Of Section 20Mmx40mm Of Teak Wood Shall Be Provided Connecting Legs.Two Bottom Rails Of Size 20Mmx40mm Shall Be Fixed Between The Legs.A Centre Stiffeners Of Size 20X40mm Shall Be Provided At Centre Of Side Bottom Rails For Extra Support Irrespective Of What Is Shown On Drg.Top Of Table Shall Be Of 18Mm Thick Prelaminated Hdf Board Of Approved Shade.4Mm Thick Teak Wood Beading Shall Be Provided Alround The Top Edges Of Table. All Wood Surfaces Exposed To View When Placed In Position Shall Be Melamyne Polished With Spray Machine Finish,After Preparation Of Surfaces.Rest All As Per Drg No Fd-277 , Rack Shoe Steel - Rack Shoe Steel. Overall Size Shall Be 700Mm Long,300Mm Wide And 880Mm High. The Legs Of The Shoe Rack Shall Be Of 25Mm Dia Ms Pipe Of 18 Gauge. The Five Shelves Of The Rack Shall Be Of 20Mm Dia Ms Pipe Of 18 Gauge Welded To Legs. The Shelves Shall Have 3Mm Dia Ms Rod 9 Nos In Widthwise And 3 Nos In Lengthwise Welded To 20Mm Dia Shelf Frame. Pre Treated With Powder Coated Oven Baked With Black Colour. Drg No Fd/E6/Map/02(R) , Book Case Steel Large - Book Case Steel Large. Over All Size Shall Be Of 840 Mm Long, 310 Mm Wide And 1675 Mm High . All Sheet Shall Be Mild Steel Sheet 1 Mm Thick, Back, Sides, Bottom, Top And Shelves.The Book Case Shall Be Provided With Four Compartments Of Equal Size. The Shutters Of Each Compartment Shall Open Towards Top And Slide Into The Depth Of The Book Case.Transparent Glass 4Mm Thick Shall Be Provided To Front Shutters. Two Steel Handles Of 100 Mm Long Shall Be Provided To Each Shutter Of The Compartment. The Locking Device Shall Be Provided To Each Compartment With Duplicate Key And Each Shutter Shall Be Provided With Decorative Key Plate . All Steel Surfaces Internally And Externally Shall Be Painted With Two Coats Of Silver Hammertone Paint Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Top Shutter Of Visible Colour As Directed By Engr-In -Charge. Drg No Fd-237, Fd-1028 , Side Board - Side Board. Overall Size Shall Be 1025Mm Long, 450Mm Wide And 750Mm High. Back Shall Be 1025Mm Long And 750Mm High Pre-Laminated Hdf Bd 18Mm Thick/18Mm Hdf, Sides Shall Be 450Mm Wide And 675Mm High Pre-Laminated Particle Bd 19Mm Thick/18Mm Thick Hdf. Base Shall Be Of 75Mm High 89Mm Thick Pre-Laminated Particle Bd /18Mm Thick Hdf Fixed At 25Mm From Front And Sides. Top And Bottom Shall Be Of 18Mm Thick Hdf Board. A Veticle Partition Of 18Mm Thick Hdf Board. Four Drawers Shall Be Provided Equally In This Space. Three Pieces Of Hdf Board 40Mmx18mm And 358Mm Long Shall Be Provided Over The Lower Three Drawers. Bottom, Sides Back Of Drawers Shall Be Of 18Mm Thick Hdf Bd. The Front Of Drawers Shall Be Of 18Mm Thick Hdf 20Mm X20mm Teak Wood Bearers Fixed Exactly In Centre Of Both Sides Of The Drawers Shall Be Provided To Each Drawer. Another 20Mm X20mm Teak Wood Bearer Shall Be Fixed To The Vertical Of The Side Bd In Such A Way The The Bearers Fixed With The Sides Of The Drawer Shall Slide Over Smoothly. On Left Side Compartment Two Horizontal Shelves, Equally Spaced Shall Provided As Shown On Drawing. The Size Of Shelves Shall Be 610Mm Long, And 387 Mm Wide. Two Catch Spring Shall Be Provided To Shutters As Directed By Engineer-In-Charge. All Wood Surfaces Exposed To View When Placed In Position Shall Be Given High Gloss Melamyne Polish With Lacquer Fininsh. Drg No Fd-1112 , Table Excutive With Side Table For Officer - Table Excutive With Side Table For Officer. Top 41Mm Thick Mlamine Edge Band With Leather Pad. Legs- 18 Mm Thick Melamine Edge Band. Table Size 2100X1050x750mm.With Storage Unit. Storage Unit Size 1200X450x670mm. (As Per Trade Patern As Per Sample And Directed By Engineer-In-Charge) , Table Dining 4 Person - Table Dining 4 Person. All As Per Drg, The Wood Shall Be 1St Class Hard Wood Teak Free From Any Joints Cracks And Knots. The Top Shall Be Made Out Of 18Mm Thick Hdf Board Exterior Grade One Side Teak Lamination In Wange / Wallet (As Approved) Colour And One Side White Lamination. All Exposed Edges Of Ppb Shall Be Provided Wooden Beading Of Teak Wood 4Mm Thick X 18Mm Wide Duly Polished With Matching Colour The Frame Shall Be Polished After Prepration Of Surfaces With Two Or More Coats Of Brown / Walnut Colour Melamyne Polish With Spray Machine As Per The Requirement To Its Glossy Look. Rest All As Shown On Drg And As Directed By Engr-In-Charge. Drg No Fd/Map-Ii/03 , Table Dressing Gents With Mirror - Table Dressing Gents With Mirror. All As Per Drg, The Frame Shall Be Strictly As Per Drg Wallet/Teak Colour As Approved. The Mirror Shall Be Of 5Mm Thickness. All Shown On Drg And As Directed By Engr-In-Charge. Drg No Fd-379 , Recepticle Pvc - Recepticle Pvc. The Body Of Receptacle Pvc Shall Be Made Up Of Thick Polymer Plastic .It Shall Be Of Capacity 20 Liters, Provided With Lid And Handle As Shown In Drg. Drg No Fd/E6/Map/13 , Hat Stand With Mirror - Hat Stand With Mirror. Overall Size Shall Be 1330 Mm Long, 710Mm High. The Inner Frame Shall Be Of 50Mmx20mm Teak Wood Battens Six In Nos .The Back And Front Of Frame Shall Be Covered With 6Mm Thick Commercial Ply.The Edges Of The Frame Shall Be Covered With 6Mmx35mm Teak Wood Edging Fixed Alround The Frame With Headless Nails And Adhesive.Six Brass Pegs 120Mm Long Shall Be Fixed Over The Wooden Membrane With Brass Screws As Shown In Drg.5Mm Thick Looking Mirror Of (Saint Gobian,Modiguard/Atul) Shall Be Provided As Shown On Drg With Beading Alround . Mild Steel Key Plate Shall Be Provided At Both Top Corners Of The Hat Stand. All Exposed Surfaces Shall Be Given High Gloss Melamyne Polish With Lacquer Spray Machine Finish. Rest All As Per Drgs No Fd- 361 , Sofa Set 5 Seater - Sofa Set 5 Seater. All As Per Drg, The Timber In All Around Shall Be First Class Hard Wood Teak,The Cushions Shall Be Made Out Of Pu Foam Of Min 40 Density Of Approved Make And Covered With Tapestery Cloth Of Approved Quality, Pattern And Colour Before Incorporating In Work. The Frame Shall Be Polished After Prepration Of Surfaces With Two Or More Coats Of Walnut/Natural Colour Melamyne Polish With Spray Machine As Per The Requirement To Its Glossy Look Rest All As Shown On Drg And As Directed By Engr-In-Charge. Drg No Fd 1113 , Chair Dinning - Chair Dinning. Chair Dining With Seat Cushioned Shall Be Made To The Shape, Size And Design As Shown On Drg And As Specified In Particular Specification And Shall Be Manufactured In Accordance With Relevant Is. All Wood Work Shall Be Of Kiln Seasoned And Chemically Pressure Treated Ist Class Hard Wood (Teakwood). Seat Shall Be 75Mm Thick Of Polyurethane Foam Density Of 40 Kg/Cu.M Covered With Fabric Of Acrylic/Polyester/Polypropylene And Upholstered With Good Quality Leatherised Of Foam As Approved By Ge Costing Not Less Than Rs 800/Mtr. Plywood For Seat Shall Be 12Mm Thick Bwp Grade. Nylon Buffers Shall Be Of Best Quality As Approved By Ge And Shall Be Provided Under Each Leg And Fixed With 25Mm Long Steel Screws Of Suitable Size. All Wooden Surfaces Exposed To View (Except Under Sides Of Frame And Bottom Of Legs) Shall Be Melamyne Polished. All Other Items / Fittings Shall Be As Shown On Drawing And Provided As Per Relevant Is And Trade Engineering Norms / Pattern. Drg No Fd/Map-Ii/04 , Table Dressing Ladies With Mirror - Table Dressing Ladies With Mirror. The Overall Size Of The Table Dressing Shall Be 1150Mm Long 380Mm Wide And 1700Mm High. The Sides, Top ,Back And Front Of The Base Unit Shall Be Of 18Mm Thick Prelaminated Hdf Board. The Bottom Of The Side Units Shall Be Of 12Mm Thick Hdf Board. The Sides And Back Of Drawers Shall Be Of 12Mm Thick Prelaminated Hdf ,Bottom Of The Drawers Shall Be Of 6Mm Thick Bwp Ply Whereas The Front Of The Drawers Shall Be Of 18Mm Thick Prelaminated Hdf Board.5Mm Thick Electro Copper Plated Mirror Shall Be Fixed Over 6Mm Thick Bwp Plywood Back. Track Rails 25Mm X 25Mm In Section On One Side Telescopic Channel On Two Vertical . The Overall Size Of The Stool Shall Be 440Mm Long 350Mm Wide And 425Mm High. The Four Sides Shall Be Of 18Mm Thick Prelaminated Hdf .The Top Of The Stool Shall Be Of 12Mm Thick Bwp Plywood Openable As Shown In Drg.Four Heavy Duty Revolving Nylon Double Wheels Shall Be Provided At Base Below The 6Mm Base Ply Fixed Over Wooden Runner 20Mmx20mm.The Seat Of The Stool Shall Be 75Mm High ,Made Of Foam 40 Density Covered With Tapestry Cloth, Costing Not Less Than Rs 80 /Mtr, As Approved By Engr-In-Charge/Ge.Rest All As Per Drg. Drg No Fd/Map-Ii/07 , Bath Mat Pvc - Bath Mat Pvc. The Bath Mat Pvc Shall Be Made Up Of 5Mm Thick Ppcp Material .The Size Of The Bath Mat Shall Be 400Mm Lx300mm Wx250mmh.The Bath Mat Shall Have Centre Leg Of Dia 25Mm.The Four Legs Shall Be In Arc Shape And Of Size 10Mmx100mm.The Top Of The Bath Mat Shall Have 3Mmx10mm Thick Stiffener Moulded Along With The Seat In Single Piece Underneath. The Weight Of The Bath Mat Shall Not Be Less Than 1.3 Kgs. Drg No Fd/E6/Map/07 , Bin Solied Linen Multi Purpose - Bin Solied Linen Multi Purpose. Overall Size Shall Be Of 1000Mm Long, 380Mm Wide And 760Mm High. Bottom Rest Shall Be Made Of 18Mm Thick Hdf Board And Shall Be 900Mm Long And 280Mm Wide And 75Mm Hih Joined Together In Long And Short Sides. The Bin Shall Be 1000Mm Long, 380Mm Wide And 385Mm High. Back Side Shall Be Of 18Mm Thick Hdf Board 1000Mm Long And 685Mm High. Sides Shall Be Of 19Mm Thick Mdf Board 380Mm Wide And 685Mm High. Top And Bottom Shall Be Of 18Mm Thick Hdf Board 1000Mm Long And 380Mm Wide. A Vertical Partition Shall Be Provided At 400Mm From Inner Face Of Left Hand Side Which Shall Be Of 18Mm Thick Hdf. Two Drawers And A Cupboard Shall Be Provided On The Right Hand Side. Of The Bin. Bottom, Sides, Back And Front Of Drawers Shall Be Of 12Mm Thick Hdf Board. Front Shutter Of Cupboard Shall Be Hinged With Continuous Piano Type Hing And Shall Be Side Hung.The Shutter Shall Be Provided With 100Mm Long Mild Steel Powder Coated Handle And Ball Spring Magnetic Catcher As Shown On Drawing. 18Mm Thick Hdf Board 543 Mm Long And 40Mm Wide Shall Be Provided As Base Support In The Front Under The Drawers. Teak Wood Bearers Two Numbers Shall Be Of 20Mmx20mm In Section And Fixed To Drawers. A Handle Shall Be Fixed In The Center Of The Each Drawer With 100 Mm Long Powder Coated Mild Steel. All Front Edges Of Hdf Bd Shall Be Fixed With 4Mm Thick Teak Wood Edging. The Shutter Shall Have 4Mm Thick Teak Wood Edging All Round Its Edges. All Exposed Surfaces Of Teak Wood Shall Be Given High Gloss Melamine Polish Finish. Ge Drg No Fd/E6/Map/09