Tender For Beautyfication Od Sant Sarover Garden Near Delwara Temple At Mount Abu
Tender Value
7.26 Crore
Estimated cost
Bid Submission
19 Nov 2026
9 days left
EMD
14.52 Lakhs
Bank guarantee accepted
Document Fee
2500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Sirohi → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Beautyfication Od Sant Sarover Garden Near Delwara Temple At Mount Abu
BOQ
| Sl. No. | Item Description |
| 1 | Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to a lead of 50 metres from road boundary including removal and disposal of top organic soil not exceeding 150 mm in thickness as directed by Engineer. In area of light jungle |
| 2 | Dressing of earth work in surface excavation including cutting and filling upto 30cm depth including disposal of excavated earth upto 50m and lift upto 1.5 m. |
| 3 | Fine dressing the ground. sqm 3.45 |
| 4 | Earth filling with available surplus soil excavated from foundations and taken only from outside of building plinth in layers not exceeding 20cm in depth, consolidating each deposited layer including ramming and watering and consolidation with lead up to 50 m and lift upto 1.5 m. |
| 5 | Carriage of Materials by mechanical transport including loading, unloading and stacking : Earth lead upto 5 km |
| 6 | Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level. In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. Depth upto 1.5 m |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 8 | Random rubble masonry with hard stone in foundation and plinth :Cement mortar 1:36 (1 cement : 6 coarse sand) |
| 9 | Extra for random rubble masonry with hard stone in superstructure above plinth level and upto two stories |
| 10 | Extra for random rubble masonry with hard stone in : Square or rectangular pillars |
| 11 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto two stories in all shapes and sizes in: Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 12 | Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete. |
| 13 | Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 14 | Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform. |
| 15 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level :1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 16 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto two stories excluding cost of centring, shuttering, finishing and reinforcement : 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 17 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto two stories excluding the cost of centring, shuttering, finishing and reinforcement:M-20 Grade Concrete (1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) -As per design mix) |
| 18 | Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars. |
| 19 | Cement plastering including T&P, scaffolding, material and complete labpour, including cost of water, curing, racking of joints etc. with 20 mm cement plaster of mix : 1:3 (1 cement : 4 fine/ coarse sand) |
| 20 | Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm). |
| 21 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 22 | Distempering with 1st quality acrylic washable distemper (ready mixed) of approved manufacturer and of required shade and colour complete. as per manufacturer's specification. Two or more coats on new work. |
| 23 | Grading roof for water proofing treatment with water proofing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 24 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75mm deep chase |
| 25 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibr cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately For the purpose of measurement the entire treated surface will be measured. |
| 26 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 27 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces. |
| 28 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel rimer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 29 | Providing and fixing 1st quality ceramic glazed vitrified tiles of colour standard white, grey, ivory, fume, red brown, light green, light blue, and other light shades with water absorption less than or equal to 0.08% confirming to IS : 13753 & IS : 15622 in floor, steps etc laid on bed on neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on wall and pillar) Size 600mm x 600mm |
| 30 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 31 | Random rubble dry stone Kharanja (soling) under floor. |
| 32 | Filling with locally available river sand at all levels including watering ramming consolidating and dressing complete including cost of sand. |
| 33 | Providing and fixing of precast concrete interlocking tiles of desired shape of M 30 grade manufactured from fully computerized automatic stationery hydraulic vibrio pressed machine and fully computerized automatic batching plant of class A1/A2 as per BS6717:2001. The CC interlocking paving blocks be laid on average 50mm. thick bed of coarse sand and the joint is to be filled with finesand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer incharge.The rates to be inclusive of all lead & Lifts etc. complete as per specifications. Tensile splitting strength, abrasion and brakingload etc. as per BS 6717:2001, Grey cement. 60mm thick |
| 34 | Chequered precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment tomatch the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade using 50% white cement 50% Grey cement. |
| 35 | Hindi (Matras, Commas and the like not to be measured and paid for. Half letters shall be counted as half). |
| 36 | English and Roman (Hyphens, commas and the like not to bemeasured and paid for) |
| 37 | Providing and fixing 1.2 metres high GI barbed wire fencing with 1.8 m angle iron posts 40 mm x 40 mm x 6 mm placed every 3 metres center to center founded in M15 grade cement oncrete, 0.6 metre below ground level, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with 9 horizontal lines and 2 diagonals interwoven with horizontal wires, fixed with GI staples, turn buckles etc complete as per clause 807 of MoRTH pecification & type \\"A\\" as per IS : 2781978 size designation 5 (line wire 2.24, point wire 2.00mm mass 97106 g/m) including all material, labour. |
| 38 | Providing and fixing Tubular Steel Railing on Precast RCC posts, 1.2 m high above ground level Providing, fencing and erecting 50 mm dia G.I pipe railing in 3 rows on precast M20 grade RCC vertical posts1.8 metres high (1.2 m above GL) with 3 holes 50 mm dia for pipe, fixed 2 metres centre to, complete as per approved drawing including all material, labour. |
| 39 | Providing and fixing precast cement concrete M-20 grade (Usingmechanical Concrete Mixer) kerb stone top and bottom width 115 and 165 mm respectively, 250 mm high on 150 mm thick PCC M-10 grade foundation as per design, including fixing at site as per clause 408 of oRT&H Specification including all material, abour, machinery, lighting, guarding and maintenance of diversion. |
| 40 | Providing and fixing 1.2 metres high GI barbed wire fencing with 1.8 m angle iron posts 40 mm x 40 mm x 6 mm placed every 3 metres center to center founded in M15 grade cement concrete, 0.6 metre below ground level, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with 9 horizontal lines and 2 diagonals interwoven with horizontal wires, fixed with GI staples, turn buckles etc complete as per clause 807 of MoRTH specification & type \\"A\\" as per IS : 2781978 size designation 5 (line wire 2.24, point wire 2.00mm mass 97106 g/m) including all material, labour. |
| 41 | Supplying and fixing of GI chain link fencing of required width in mesh including strengthening with 2 mm dia GI wire/ G.I. staples/ G.I.U-nails/ nuts bolts with 2.4 m angle iron posts 50 mm x 50 mm x 6 mm placed every 3 metres center to center founded in M15 grade cement concrete 30cmx30cmx60cm, 0.6 metre below ground level, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only etc completeas required and as per direction of Engineer-in-charge. Mesh size 50mm x 50mm made of GI wire 3.15mm dia |
| 42 | Supply and fixing different type of steel pre-fabricated garden bench/ jhula/ slides and other children play items made of steel duly painted as per approved design and specifications by engineer in charge made of MS pipe, Flats, rectangular hollow section or other steel sections duly welded and or nut bolted where ever required, rubbing and buffing welded joints to make safe for use of children and painted in approved pattern complete as required. |
| 43 | Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications and as per clause 2504 of MoRT&H Specification With R.R. Stone/ bolder, weighing not less than 40 kg, thickness not less than 150mm, Specific gravity not less than 2.65. |
| 44 | Providing and fixing Stone jali 50mm thick Red/Pink sand stone as per ornamental design to fixed with white cement/epoxy mortar including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade. |
| 45 | Providing and fixing Red/Pink sand stone post (Mataga) having size 100x100mm heights 600 to 750 mm as per ornamental design suchas like flower octagonal head border etc. to fixed with white cement/epoxy mortar including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade. |
| 46 | Wall lining butch work upto 10m height with red/ white sand stone 40 mm thick rough facing on the exposed surface with stone strips of minimum length 300 mm and required width including embedding every tenth layer and bottom most layer in masonry or concrete after making necessary chases of size 75x75mm and by providing layer of 75mm thick strips i/c 12mm thick bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c ruled pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment to match the shade of stone complete as per direction of Engineer-in-charge. |
| 47 | Stone tile work for wall lining upto 10 m height with special adhesive over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement with an admixture of pigment to match the stone shade. 8mm thick (mirror polished and machine cut edge) Granite stone of any colour and shade. |
| 48 | Making Mehrab's, Arches, pillars, highly decorative creepers, flower of small sizes etc.in lime Surkhi plaster (1:2) as per B248oldtraditional practices (Arches, Mehrab's) in three coats for base course and subsequent course and Loi tamping, beating till the shrinkage cracks are disappear than making ornamental flowering/design etc. The work is to done with all leads and lifts as per work of restoration nature as per Jaipur practice. |
| 49 | Making Kangura on top of the wall as per Jaipur traditional practice with tile brick bats/stones in grinded Lime Surkhi mortar 1:2 thickness of kangoora 15cm & height 45cm, finishing with lime Surkhi mortar 1:2 complete in all respect up to 10.00 meter from ground level including all scaffolding, lead & lift. |
| 50 | Providing new /restoration of decorative sandstone columns as per the original details found on site of size around 2.1 to 2.5 metres inheight & (square/ rectangular upto 200 mm x 400mm ). The damaged portions of the original column to be carefully dismantled without damaging the adjacent areas, & replacing the same with new detail of the same size & design. Sample of the terra cotta column to be shown to the Engineer in-charge for approvals beforeprocuring & fixing the same on site. Item to include all necessary anchoring details, scaffolding if required etc. complete. Mode ofMeasurement: Item to be paid each restored/new column for using plain |
| 51 | Araish plaster (as per Jaipur practice) 1:2 ( 1 lime : 2 Zikki) on lime plaster or plane back ground including preparation of lime for 6 months by slaking of lime with curd and changing the water every week. The Kara plaster of not more than 6 mm thick is to be left the maximum of 3 months to appear the shrinkage & temperature cracks. Over the Kara plaster 2mm layer of grinded lime putty is to be done and is to be rubbed Gently by Akik stone. Then adding Khoppra & Ghee and inserting the design of colour boarder all round. |
| 52 | Coloured plain Araish work 1:2 (1 lime : 2 zikki) on lime plaster or plane back ground including preparation of lime for 6 months by slaking of lime with curd and changing the water every week. The Kara plaster of not more than 6mm thick is to be left the maximum of 3 months to appear the shrinkage & temperature cracks. Over the Kara plaster 2mm layer of grinded lime putty is to be done and is to be rubbed Gently by Akik stone. Then adding Khoppra & Ghee and inserting the design of colour boarder all round including desired colour stone pigment to match the existing colour. |
| 53 | Stucco work in lime, Surkhi, mortar (1:2) as per existing design work/ traditional practices by skilled craftsman, the stucco work should bedone as per restoration nature, the mortar should be prepared by grinding mill adding gur, methi & gugal.. The thickness varies from 50 mm to 100mm as per the design (minimum rectangular surface area to be measured). |
| 54 | Painting on Stucco work with stone colours including base coat of khameera as per traditional practice (minimum rectangular to be measured). |
| 55 | Conservation of fresco paintings in monuments by cleaning of the painted surface from all types of stains, dust, dirt, greasy & oily accretions etc. with the help of suitable chemicals, removal ofcracks, consolidation of flaking paint layer and plaster, filling of the lacunae in the plaster, treatment of salt effect and altered paint layerretouching of the lost portions and providing a preservative coating. |
| 56 | Conservation of oil paintings & portraits in monuments by cleaning of the painted surface from all types of stains, dust, dirt, greasy & oilyaccretions etc. with the help of suitable chemicals, removal of cracks and holes, consolidation of flaking paint layer and plaster, filling of the lacunae in the plaster, treatment of salt effect, retouching of the lost portions and providing a preservative coating. |
| 57 | Exposition of the original surface of fresco paintings/tempra paintings by careful removal of uppercoating of hitewash/paint/distemper/plaster, araish etc. without any harm to the original hidden art work, conservation of the paintings & strengthen the original art work with the preservative coating and making it water proof as per direction of the Chemist-in-charge. |
| 58 | Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with white cement mortar 1:2 (1white cement : 2 stone dust) with an admixture of pigment matching the stone shade. White sand stone |
| 59 | 30mm red sand stone sun-shade (chisel-dressed) supported on red sand stone brackets, fixed in walls with cement mortar 1:4 (1 cement : 4 coarse sand) including finishing complete. |
| 60 | Providing and fixing red sand stone brackets 55x22.5x45cm sunk and moulded including providing and fixing with 4 Nos. gun metalcramp 25x6mm 30 cm long and dowel bars 7.5 cm long 6 mm dia as per design. |
| 61 | Stone work (machine cut edges) for wall lining etc. (veneer work) backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing by means of cramps which shall be paid for separately) : Red sand stone - Exposed face fine dressed with rough backing. 30 mm thick. |
| 62 | Trenching in specified soil upto a depth of 60 cm. including removal and stacking of serviceable materials and then disposal by spreading and neatly leveling within a lead of 50 metres and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and farm-yard manure before and after flooding with water (excluding cost of imported earth and sludge or farm-yard manure). |
| 63 | Supply at site of work well decayed farm yard manure, from any available source, approved by the engineer in charge including screening and stacking |
| 64 | Grassing with 'Doobs' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed. In rows 7.5 cm apart in either direction |
| 65 | Filling mixture of earth and sludge farm-yard manure in the desired proportion in trenches, flooding with water and leveling (cost of supplying earth and sludge or farm yard manure and labour for mixing not included in this rate). |
| 66 | Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart. |
| 67 | Supplying, erecting and fixing in position specified precast RCC bench made of RCC grade M-30 consisting of 2 Nos. “L” shaped base support of thickness 100 mm back height 1000mm, front height 450 mm, base width 420mm and 5 Nos. RCC planks of size of 1500x100 x 50 mm and 1 Nos RCC planks of 150x200x50mm including joining all parts with galvanised nuts and bolts of suitable size. All bolts to be sealed after assembly with nice finish and appearance and level complete in all respect as per direction of engineer in charge. Every bench should have a manufacture‘s logo of appropriate size Engraved at suitable place. |
| 68 | Supply and fixing different type of steel pre-fabricated garden bench/ jhula/ slides and other children play items made of steel duly painted as per approved design and specifications by engineer in-charge made of MS pipe, Flats, rectangular hollow section or other steel sections duly welded and or nut bolted where ever required, rubbing and buffing welded joints to make safe for use of children and painted in approved pattern complete as required. . |
| 69 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) 20mm nominal outer dia pipes |
| 70 | 40mm nominal outer dia pipes |
| 71 | 62.5mm nominal outer dia pipes |
| 72 | Supply and planting following in poly bags / arthen pots well branched, well established & free from disease of 300 mm min. height ground covers at site in 0.3 m dia holes, 0.3 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required. Wedelia trilobata ( SunFlower Family) |
| 73 | Alternathera green (Parrot Leaf) |
| 74 | Rhoeo spathacea 'Compacta‘ ( Oyster, Boat Lily) |
| 75 | Golden duranta |
| 76 | Supply and planting following in poly bags / earthen pots well branched, well established & free from disease of 900 mm min. height plants at site in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required. Ficus panda |
| 77 | Tabernaemontana variegated ( Chandni) |
| 78 | Supply and planting following in poly bags / earthen pots well branched, well established & free from disease of 600 mm min. height hurbs at site in 0.45 m dia holes, 0.45 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required. Rhaphis excelsa with 3-4 suckers ( Lady Palm) |
| 79 | Furcaria with 10-12 leaves ( cactus) |
| 80 | Phonenix sylvertris ( Date Palm) |
| 81 | Supply and planting following species best quality container grown healthy trees of 2 mt. min. height, well established & free from disease at site in 0.90 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required. Plumeria alba ( Champa) |
| 82 | Neem(Azadirachta indica) |
| 83 | Erythrina variegata (Lantern Tree) |
| 84 | Quis quallis indica ( Madhu Malti) |
| 85 | Table palm |
| 86 | Acacia senegal |
| 87 | Moringa concanensis |
| 88 | Tinospora cordiflia |
| 89 | Supply and planting following species best quality container grown healthy trees of 3 mt. min. height, well established & free from disease at site in 1.20 m dia holes, 1.20 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required. Plumeria alba ( Champa) 3 M height minimum |
| 90 | Gulmohar(Delonix regia) |
| 91 | Neem(Azadirachta indica) |
| 92 | Bauhinia blakeana (Arckid) |
| 93 | Erythrina variegata (Lantern Tree) |
| 94 | Yucca |
| 95 | Providing and fixing on wall face Unplasticised Rigid PVC Single socketed pipes rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 75 mm diameter |
| 96 | 110 mm diameter |
| 97 | Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Coupler 75 mm |
| 98 | 110 mm |
| 99 | Single tee without door 75x75x75 mm |
| 100 | 110x110x110 mm |
| 101 | Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm |
| 102 | 110 mm |
| 103 | Constructing masonry Chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design : With bricks |
| 104 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore. |
| 105 | Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles,18 SWG G.I. box with earth terminal, 6 A switch , 3 pin ceiling rose/ Lamp holder / 3 point Connector, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 - 1995), Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 . For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . Short point (up to 3 mtr.) |
| 106 | Medium point (up to 6 mtr) |
| 107 | Long point (up to 10 mtr) |
| 108 | Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles,18 SWG G.I. box with earth terminal of required size, 6 A switch, 3/5 pin 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 - 1995), Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For specification ofcopper Conductor, Phenolic Laminated sheet's & Electrical/ Wiringaccessories refer Chapter E - 04, E - 05 & E - 07. For additionaltechnical parameters of products/ work , refer Annexure \\"A\\"attached with this BSR . On Board |
| 109 | Short point (up to 3 mtr.) |
| 110 | S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. 25 mm |
| 111 | 32 mm |
| 112 | Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification of Wiring accessories refer Chapter-56 related item & For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 113 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. 2 x 1.5 sq.mm |
| 114 | 3 x 1.5 sq.mm |
| 115 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 116 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. |
| 117 | 1 x 6.0 sq.mm |
| 118 | 1 x 10.0 sq.mm |
| 119 | Supply and laying PVC Insulated and PVC Round Sheathed Multi Core copper conductor (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing pipe / open trench / Cable tray / on surface including making connection etc. as required. 1.5 sq.mm x 3 core |
| 120 | 4.0 sq.mm x 4 core |
| 121 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge. Single pole MCB (With B/C curve tripping Characteristics) 0.5 A to 5 A rating |
| 122 | Single pole MCB (With B/C curve tripping Characteristics) 6 A to 32 A rating |
| 123 | Double pole MCB (With B/C curve tripping Characteristics) 6 A to 32 A rating |
| 124 | Triple pole MCB (With B/C curve trippingCharacteristics) 6 A to 32 A rating |
| 125 | Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering overall poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge. Four pole Isolator 40 A rating |
| 126 | Four pole Isolator 63 A rating |
| 127 | SITC of 4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings , conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% ICU. U imp =8 KV, rated insulation voltage 690 V. provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution All as per pre approved by Engineer in-charge. 4 pole MCCB With Thermal Magnetic release. 125 Amp , 25 kA, adjustable O/L & adjustable S/C setting, |
| 128 | Supply and fixing of following accessories for Moulded case circuit breaker (MCCB) compatible to main MCCB OEM as per PWD specification for electrical Works, conforming to IS/IEC 60947 P - 2 :2003 including making connection etc complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in-charge. Extended Rotary Handle |
| 129 | Providing & Fixing of 240/415 V factory fitted RCBO with overload, short-circuit and earth leakage protection with ISI marked (IS12640-2)/ conforming to IEC 61009-1, breaking capacity 10 KA, provision for pad lock, min. Electrical operation 10,000 upto 63 A rating , minimum phase termination capacity of 35sq.mm. , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge. Four pole 30 mA sensitivity 63 A rating |
| 130 | Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge. Metal door (single phase) IK-09 and IP-43 with Metal end box 4 Way (4+2) |
| 131 | Metal door (Three phase) Per phase isolation, Horizontal IK-09 and IP-43 with Metal end box 8Way(Incomer 8,Sub Incomer2+2+2) |
| 132 | SITC of IP-42 and general construction confirming to IS:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and Other parameters required as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:-(a)Thickness of CRCA sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. Removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided(b)complete panel shall undergo a process of degreasing, Water rinsing, Activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then Powder coated with approved shade of minimum 70 microns on both side of panel. The panel having PE foam/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire.[c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 Sq.mm, Earth wire with 2.5 Sq.mm and CT with 2.5 sq.mm flexible copper wire only. All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar. ( Cost of Bus bar / Flexible wire for Interconnection between Main busbar and Switchgear is to be Paid Extra ) (d)Wiring between components within switchgear and Incoming / outgoing cable shall be done through the terminal block only. Direct connection shall not be permitted. Each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. For tap-offs, adjacent terminals with shorting strips shall be used. 10% Spare terminal blocks shall be provided. Wire identification on marking strip shall correspond to the designation of the wiring diagrams. All wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram.(e)All wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, Wiring between terminals of various devices shall be ‘point to point’ (no wire splitting or tee connections) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging.(f)Floor mounted panel shall be mounted on Base frame of ISMC channel size 100 x 50 x 5 mm ( to be paid Extra )(g) Tests: The insulation resistance (with 1000 V Megger) and High voltage Power frequency test (by applying a voltage of 2.5KV for one minute) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. The insulation resistance shall not be less than three megaohm. CT Secondary current injection test shall also be carried out.(h) only outer surface area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator only (CPRI Test certificates to be submitted)All as per pre approved by Engineer in-charge. |
| 133 | Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar by means of SMC / DMC type insulator with standard short circuit withstand capacity , high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. All as per pre approved by Engineer in-charge. Electrolytic grade (Cu-ETP) Tin Coated annealed copper bus bars IACS 100% grade |
| 134 | Providing & Fixing of IS: 13875 & IEC :61326 confirming LED Digital type (up to 500) V range Multi Function Meterr of class 1 accuracy as per IS : 1248 of size 96mm x 96 mm including making connection by PVC insulated copper conductor with PVC sleeves / channel etc. as required. All as per pre approved by Engineer in-charge. Three phase AMP+HZ+PF+KW+KVA+KVAR+T.ENERGY+THD-I, THD-V & RUN HRS |
| 135 | Providing & Fixing of BIS approved Current Transformer as per PWD specification for electrical Works ,ISI marked as per IS 2705-1992/ conforming to IEC 60044-1, with secondary terminal of CT shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as required Current transformer Ring Type Tape Wound/Resin Cast Wound as per IS 16227 with, Accuracy Cl, CT ratio and burden as specified. ISF<=5, Cu cross section of secondary wire 1.5sqmm (minimum), including all necessary support in existing panel including connection etc. as required . All as per pre approved by Engineer in-charge. Ring type tape wound CT C T Class 1, Ratio upto 150/5, Burden 5 VA |
| 136 | Providing & Fixing of 110/220 V, unibody LED Indicating lamp IEC 60947 with integral circuit, IP 65 above panel & IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm, front LED cover dia min. 29 mm, contact material phospher bronze for Led, PCB contacts shall be of brass (tin plated), impulse dielectric tested for 2.5 KV, Rated insulation resistance shall be 100 M ohm at 500VDC including connection etc. as required. All as per pre approved by Engineer in-charge. Red/yellow/Green colour |
| 137 | Providing & Fixing of AC operated heavy duty 230 /440 Volt power contactor as per PWD specification for electrical Works, ISI marked IS/IEC 60947-4-1 : 2000 having provision of mechanical interlocking, auxilary contacts, Din rail mounting type including making connections, testing etc. as required. All as per pre approved by Engineer in-charge. 4 pole Power contactors with following AC 1 Rating 63 Amp. |
| 138 | Providing & Fixing of mechanical / digital time switch having following day / week programme and minimum 100 hours reserve and AC1 rating of 16-20 amperes including making connection, programming conforming to IEC 60730-1 and 60730-2-7 etc. as required. All as per pre approved by Engineer in-charge. One day reserve (Analog type ) |
| 139 | Providing & Laying P.V.C. insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810. 6.0 Sq. mm 2 core |
| 140 | 10.0 Sq. mm 4 core |
| 141 | 16.0 Sq. mm 4 core |
| 142 | 35.0 Sq. mm 3.5 core |
| 143 | 50.0 Sq. mm 3.5 core |
| 144 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured Copper cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810 1.5 Sq. mm 3 core |
| 145 | 2.5 Sq. mm 3 core |
| 146 | Supplying and making one end termination with Nickel plated heavy duty brass single compression gland (as per IS 12943-1990)) SIBG type consisting of Check Nut, Gland Body, Metal Washer(3 Nos.), Outer Seal Rubber Ring, Compression Nut, heavy duty aluminium lugs (as per IS 8309 -1993) duly crimped with crimping tool, PVC tape as per IS 8337-1976 of following size of PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required.All as per pre approved by Engineer in-charge. 3.5 x 35.0 sq.mm |
| 147 | 3.5 x 50.0 sq.mm |
| 148 | 4 x 10.0 sq.mm |
| 149 | 4 x 16.0 sq.mm |
| 150 | Supplying and making end termination with heavy aluminium lugs ( Pin / ring type ) confirming to IS 8309 -1993 & IS 8337-1976 duly crimped with crimping tool, PVC tape etc of following size.All as per pre approved by Engineer in-charge 6.0 Sq.mm |
| 151 | 10.0 Sq.mm |
| 152 | 16.0 Sq.mm |
| 153 | 35.0 Sq.mm |
| 154 | 50.0 Sq.mm |
| 155 | P / L of Double wall corrugated HDPE pipe confirming to IS : 16205 P-24, Stiffness Class 750 N, Externally corrugated and having smooth surface inside with HDPE Coupler, Elbow, Tee at required Depth below the ground for laying cable of following Nominal Outer dia. MFR Test report from NABL accrediated is to be submitted.(Excavation of Earth & Back filling with compaction is to be Paid Extra)All as per pre approved by Engineer in-charge. 50 mm |
| 156 | 75 mm |
| 157 | labour charges for Excavating trenches of required width for pipes dressing of sides, ramming of bottoms, depth up to 1.5 Mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 Mtr.: Ordinary Rocks |
| 158 | Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. All as per pre approved by Engineer in-charge. 10 SWG G.I. ( Hot Dipped ) Wire |
| 159 | Supply & Laying following size' B ' class , G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with accessories like bend, socket etc. for laying earth conductor/ strip / cable in ground/ surface/ recess as required. All as per pre approved by Engineer in-charge. 50 mm dia. |
| 160 | 80 mm dia. |
| 161 | Mesh earthing as per IS:3043 with Hot dipped galvanized earth strip of size 25 mm x 6 mm to form a mesh of size 1000 mm x 1000 mm in horizontal formation to create equal sections of 200 mm x 200 mm by means of welding and embodying 1 mtr. Below the ground level, refilling the pit by alternative layers of charcoal & salt up to 500 mm with 20 mm dia. GI 'B' class watering pipe, wire mesh funnel and and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm testing of earth resistance for value of 5 ohms or less as required & must record by engineer in-charge during site visit and ensure to enter in measurment book. |
| 162 | Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in-charge. 1200 mm Sweep BEE 1 Star rated (service value >=4.0 to < 4.5 ) |
| 163 | Providing & Fixing of of M.S. J- hook of standard design made out of 16 mm dia. M.S. round bar and fixed with cement concrete mortar with required support as required. All as per pre approved by Engineer in-charge. |
| 164 | P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in-charge. |
| 165 | Supply, Installation, Testing and Comissioning of Inverter type Air Cooled Hi Wall split type Air conditioners with latest star rating system as per BEE amended upto date complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU), R-32/R-410 Green Refrigerant, wireless Remote control, suitable for working between 230V +/- 10% with low & high voltage cutoff and 50 hz , single phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. All as per pre approved by Engineer in-charge. 1.5 TR ISEER not less then 3.8 |
| 166 | Supply, Fixing and testing of following capacity wall mounted stablisers having output voltage variation from 200V to 250V(+/-5%) with input voltage variation from 170V to 260V, time delay facility from 2 to 4 minute and high cutoff at 270V complete in all respect. 3 KVA |
| 167 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in-charge. 1170mm(+/-10%) LED batten with min. lumen output 2200 lm |
| 168 | Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb in existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70, minimum life time of minimum 25000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in-charge. 15 Watt |
| 169 | Providing & Fixing of ISI marked (IS:371) 6 amp surface type 3 pin ceiling rose with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including making connection testing etc. as required.All as per pre approved by Engineer in-charge |
| 170 | Providing & Fixing of ISI marked (IS:1258) batten/angle lamp holder with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screwsincluding making connection testing etc. as required. All as per pre approved by Engineer in-charge. |
| 171 | Providing and Laying RCC Foundation for Octagonal / Conical Street Light poles, High mast Poles as per Drawing attach at Table P-4 with Following Procedure & All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .A) Excavation of Pit for Foundation Size upto required depth from Ground levelB) Dressing of Pit and Dry stone pitching 200 mm thick including supply of stones and preparing surface complete.C) Providing and laying in position cement concrete of M-10 grade of 75 mm thicknessD) Reinforcement for R.C.C. work with TMT bars including straightening, cutting, bending, placing in position and binding all complete.E) Centring and shuttering including strutting , propping etc. and removal of form work for Footing and PedestalF) Providing & Fixing of 2 no. Required Size PLB HDPE Pipe & Foundation Bolt with template as per OEM Recommendations.G) Providing and Laying Reinforce cement Concrete of M-25 grade in Footing and Pedestal including Curing the foundation for 7 days.H) Providing and Fixing Nosing Angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. Lugs on each face. Pole Foundation for Octagonal pole from 3 Mtr. To 6 Mtr. |
| 172 | Pole Foundation for Octagonal pole from 7 Mtr. To 9 Mtr. |
| 173 | Providing & Fixing of Suspended mounting IP66 IK08 rated Integrated High power LED Wellglass light fixture made from Pressure Die Cast Aluminium housing, potted driver, Eye bolt for mounting, PC clear / Opal Diffuser, system lumen efficacy ≥120 lm/Watt output , THD < 10% ,p.f.≥0.95,CRI >70 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. surge protection 4 KV . OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80)certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in-charge. Minimum lumen output 3500 lm |
| 174 | Providing & Fixing of IK10 IP65 protected 600 mm height LED Bollard Luminarie with base plate made of powder coated die cast alluminium housing with UV stabalized PC diffuser. The System level Luminous efficacy ≥ 90 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<20% and input Voltage range of 90-270V AC at 50Hz. System life of 30000 Burning hours with 70% of Initial Lumens maintained Light output in Cool white or Warm White Colour as per engineers choice. driver current <750mA. Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in-charge. Minimum lumen output 800 lm Bollard |
| 175 | Providing & Fixing of IK10 IP66 / IP67 protected Rectangular shape LED Step Luminarie made of powder coated die cast alluminium housing with UV stabalized PC diffuser. The System level Luminous efficacy ≥ 90 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintained . driver current <750mA . Fixture must be in compliance with BIS Standards and Trade mak Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in-charge. Minimum lumen output 630 lm Step light |
| 176 | P &L of lP66 protected high power high power LED linear flood light system. Fixture made of powder coated extruded aluminium housing with UV stabilized PC/toughened glass cover and appropriate lens tobe used to achieve various beam angle pattern. fixture suitable for input 12vDC, power consumption should be 6W/0.5A per feet with system CRI- 70, color red/ green / blue/ /RGB /W/WW. the fixture must have IP66 protected 5mm Round female connector for input, the fixture must have provision to extend further . system life of 50000burning hours with 70% of initial lumens maintained . light output in red, green, blue, cool, white or warm white colour as per requirement. fixtu res shall be CE complete series of linear flood light. linear LED strip 1 feet (with driver) |
| 177 | Linear LED Strip 2 Feet (with Driver) |
| 178 | Linear LED Strip 4 Feet (with Driver) |
| 179 | Supply, Installation, Testing and Commissioning of Spike Light with 10 Degree Beam Deflection and 3000 K CCT. 6 Watt |
| 180 | P & F of IP-66 protected high power LED flood light system with extruded aluminium housing , toughened glass diffuser with suitable lenses on LED to achieve various beam angles, 240 volt, 50Hz, of high power LEDlamps supplied with pre wired cable of 1 mtr. Integrated driver shall be high efficiency having efficiency more than 85 % and in compliance to IEC standards. System life of 50000 burning hours with 70 % of initial lumen be maintained. Light output in red , green , blue, cool white or warm white colour as per engineers choice. Fixtures shall be CE compliance. Make Group I High power LED flood light 120 watt |
| 181 | High power LED flood light 200 watt |
| 182 | Providing & Fixing of IK08 IP-66 protected high power LED flood light system with single piece Pressure diecast aluminium housing, toughened glass diffuser with suitable lenses on LED to achieve various beam angles, of high power LED of 3 to 5 watt each . Integrated potted driver as a unique BIS R number having efficiency more than 85 % and in compliance to BIS certified and Trade mark certificate. The System level Luminaire efficacy >=125 lm/ wt. LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety .Power Factor >0.95 , THD(I) <10% , driver current <=750mA. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector , Surge Protection Min >=4KV internal and 10KV external but inside driver compartment, System life of 50000 Burning hours with 70% of Initial Lumens maintained, CRI>70 and CCT 5700K ±355K. Manufactures Word Mark/Name Engraved/Embossing/Screen printing on die cast housing to allow traceability/authenticity. Fixture shall be IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in-charge. High Power LED Flood Light Minimum lumen output 43750 lm |
| 183 | Supply installation testing & Commissioning of high mast lighting system (as per PLG 07 of ILP UK techinical report no 7 of ILE UK /IS:875 Part-1 – 2015//BSEN10025/and IS:2062 )consisting of totally hot dip galvanised by piecewise single dipped method high mast, lantern carriage suitable for up to 12 nos luminaries with welded arm (excluding luminares), mast head frame assembly with full cover, including 1 No. LED 15 Watts aviation obstruction lights, double drum type self sustaining winch, integral power tool accesible from door with padlocking arrangement (winch motor with control circuit) hot dipped galvanised heavy duty pipe lightening finial, Stainless steel 6 mm dia. wire ropes (AISI 316, 7 / 19 costruction 3 no. rope for lantern carrage & 2 no. rope for winch assembly ) foundation bolt, torque limiter,EPR insulated PCP sheathed 5 core x 2.5 Sq.mm trailing cable, including outdoor type control panel for auto on / off, reverse / forward motor operation. The mast is constructed from mild steel plates (as per IS 5986 Gr. 510 ) cut and folded to form a polygonal section, telescopic jointed and welding as per BS 5135.etc. as required on Existing Foundation. ( See table P - 03 for specs.) OEM Must have Type test certificate for wind tunnel test . All as per pre approved by Engineer in-charge. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 12.5 Mtr HM (in 2 section) suitable for 6 No. Luminaries 2 no. rope for lantern carrage & 2 no. rope for winch assembly |
| 184 | Earth work in excavation for roadway, including trimming bottom and side slopes in accordance with requirement of line, grades and cross sections, including disposal of surplus material with all lift and lead upto 1000 metre as per MoRT&H specification clause 301. In all type of soil |
| 185 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 186 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level : 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size). (As per design mix) |
| 187 | Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars. |
| 188 | Supply and laying following size twin parallel type Speaker cables of IS/ISO 9001 CERTIFIED COMPANY made with multi wire, bright annealed flexible bare electrolytic grade copper conductor, insulated with specially formulated transparent grade PVC compound, red strip for identification in existing conduit etc. as required. 2.5 Sq.mm |
| 189 | Supply, Installation, Testing & Commissioning of 5 MP IR Fixed Bullet Network Camera -1/2.7 inch Progressive Scan CMOS, 2592 × 1944 at 25fps, 2.8 mm Fixed lens, 0.003 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, BLC, HLC, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage including SD Card up to 256 GB , IP67, Alarm 1 inputs, 1 outputs, Audio 1 inputs, 1 outputs, Edge Analytics- Line crossing detection, Intrusion detection, Motion detection, Region entrance detection, Region exiting detection, Scene change detection, Face capture, Video tampering, audio exception detection, False alarm reduction through human and vehicle target classification based on deep learning CE, FCC, BIS certified |
| 190 | Supply, Installation, Testing & Commissioning of 4MP IR Outdoor PTZ Camera-1/1.8\\" Progressive Scan CMOS, 2560 × 1440 at 25fps, 5.9 mm to 188 mm, 32× Optical, 16x digital zoom, Color: 0.005 Lux at F1.5, B/W: 0.001Lux at F1.5, ICR, ONVIF, support H.265,MJPEG, 120 dB WDR, 3D Digital Noise Reduction, HLC, BLC, Defog, EIS, Triple individually configurable stream, 24 VAC & PoE, IR range: 200m, Pan: 360° endless, Tilt: From -15° to 90° (auto-flip), Pan Speed - from 0.1°/s to 160°/s, Preset Speed: 240°/s, Tilt Speed- from 0.1°/s to 120°/s, Preset Speed: 200°/s, Presets- 300, Alarm Input-2-ch alarm input, Alarm Output-1-ch alarm output, Audio-1 channel input & output, Support on-board storage up to 256 GB (SD card not included), IP66, Line crossing detection, intrusion detection, CE, FCC, BIS certified. |
| 191 | 16 port Unmanaged Network PoE Switch: 16 port PoE Switch with PoE standard of IEEE 802.3af , IEEE 802.3at, PoE port, Uplink ports |
| 192 | 16ch Network Video Recorder- Connect Up to 16 IP Cameras, Dual OS, Up to 8 Megapixels Resolution, HDMI and VGA independent outputs provided, HDMI Video output at up to 4K (3840 × 2160) resolution , VGA upto 1920 × 1080, Support H.265, MJPEG, Incoming Bandwidth 160 Mbps, 4 SATA Hard Disks, ANR Technology, 4 SATA interfaces for 4 HDDs and capacity of each HDD upto 6TB, 3× USB at least 1 × USB with 3.0, Alarm I/O 16/4, RS-485, RS-232, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, BIS certified. |
| 193 | SITC of 55'' 4k Resolution or Better LED TV with remote control and wall mount unit / floor stand complete with making connections etc. as required. |
| 194 | Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected by PVC Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per pre approved by Engineer in-charge. |
| 195 | Providing, installation, testing and commissioning of ONLINE UPS SYSTEM, Single Phase 230 V, 50 Hz with 2 hour backup SMF battery bank as per specification 2 KVA |
| 196 | Supply & Installation of IP-20 & IK-08 , UL Listed Wall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door,Vertical Mounting Rail 1.6 MM with 'U'Marking , with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19\\" angles with wall mounting provision on wall. Accessories like: 1 No of 19\\" 1U Horizontal Cable manager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of 19\\" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with Suitable Anchor fastner etc as required.All as per pre approved by Engineer in-charge. 6 U Rack with Width 600 mm & Depth 400 mm + 100 mm |
| 197 | Supply and fixing sign board upto 4.5 meter height made of the following specifications board base of A.C.P / transparent PVC acrylic sheet 3 mm thick fixed on MS hollow rectangular section size 50mmx25mm, letters made of acrylic material sheet 3 mm thick of any colour fixed with LED lights with all accessories and wiring with copper wire complete as required and as per direction in engineer in-charge. |
| 198 | P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. 2.5 Sq.mm 3 core flat / Round |
| 199 | 10.0 Sq.mm 3 core flat / Round |
| 200 | SITC of Decorative cast iron pole with single arm/double on existing cement concrete foundation, of 8 meter hight in three section with casting base should be of 1000 mm hight minimum with casting design approved by engineering incharge/procuring entity and total weight of casting (base & other casting part used) must be of minimum 50% of total weight of pole (other than inner pipe)(this should be ensured during fabrication of ordered pole by doing factory inspection of engineering incharge) and base plate of 450mmx450mmx16 mm(minimum) and thickness of MS pipe/MS gorveed pipe used must be minimum 3.25-4 mm and. The pole shall be made of Cast Iron as per IS 210:1993, precision machining and filling job to achieve good finish and a fine coat of primer on each element before assembling. After assembling of each element one coat of primer and two coats of P.U. paint are applied. Approved coloured UV resist coating of mat/ glossy/ metallic finish followed after air drying of pole. The pole shall have a weatherproof flush door and locking arrangements, Provision for inside termination box with 4way connector & 1nos 6 AMPS MCB for local isolation with cover and including4 nos of foundation bolt M24x750 steel grade of E250 to IS 2062:2011 .(payment of pole will be based on pole weight so all pole must be weighted(without light and foundation bolt) (Here 22 pole of each 320 kg consider for estimation)(design of pole will be as per approved by engineering incharge ) |
| 201 | SITC of Decorative cast iron pole with single arm/double on existing cement concrete foundation, of 4 meter height. Pole upper section of length 3mtr is of dia 76mm and 1 meter bottom section of dia 114mm with decorative casting with base plate as per drawing with casting design approved by engineering incharge/procuring entity (this should be ensured during fabrication of ordered pole by doing factory inspection of engineering incharge) and base plate of 400mmx400mmx12 mm(minimum) and thickness of MS pipe/MS gorveed pipe used must be minimum 3.25-4 mm and. The pole shall be made of Cast Iron as per IS 210:1993, precision machining and filling job to achieve good finish and a fine coat of primer on each element before assembling. After assembling of each element one coat of primer and two coats of P.U. paint are applied. Approved coloured UV resist coating of mat/ glossy/ metallic finish followed after air drying of pole. The pole shall have a weatherproof flush door and locking arrangements, Provision for inside termination box with 4way connector & 1nos 6 AMPS MCB for local isolation with cover and including4 nos of foundation bolt M24x750 steel grade of E250 to IS 2062:2011 .(payment of pole will be based on pole weight so all pole must be weighted(without light and foundation bolt) (Here 37 pole of each 190 kg consider for estimation)(design of pole will be as per approved by engineering incharge). |
| 202 | Supply of IP 65 Protected Decorative Led Post Top suspended lantern range made up of spun aluminum canopy with die cast aluminum spigot. Fitted with glare free optically designed prismatic diffuser protected LED decorative Post Top lantern with Low glare optical design & Acrylic diffuser 90W 220-240V, 50Hz (Integrated driver) driver shall be high efficiency having efficiency > 85% and in compliance ti IEC standard (Integral with ligit fixture) system life of 25000 burning hours 70% of initial lumens maintained. system efficency should greather than or equal 75Lm/W Power Factorv > 0.95 and CRI 70. All as per pre approved by Engineer in-charge. decorative LED Top 120Watt (ww/w) |
| 203 | Supply of IP 65 Protected Decorative Led Post Top suspended lantern range made up of spun aluminum canopy with die cast aluminum spigot. Fitted with glare free optically designed prismatic diffuser protected LED decorative Post Top lantern with Low glare optical design & Acrylic diffuser 45W 220-240V, 50Hz (Integrated driver) driver shall be high efficiency having efficiency > 85% and in compliance to IEC standard (Integral with light fixture) system life of 25000 burning hours 70% of initial lumens maintained. system efficiency should greater than or equal 75Lm/W Power Factor > 0.95 and CRI 70. All as per pre approved by Engineer in-charge. Decorative LED Top 45 Watt (ww/w) |
| 204 | Providing of IP66 protected High power LED Flood light system with pressure die cast housing, with suitable lenses on LED to achieve various beam angles, System lumen efficacy>=110lm/w, Driver shall be high efficiency having efficiency>85%, CRI>70, Power factor>0.95, System life of 50,000 Burning Hours with 70% of Initial Lumens maintained. Light output in warm white. LED Flood Light 50W (Warm White/Green) |
| 205 | SITC of 700 watt Dual channel PA Mixer Amplifiers with Digital Player with fol1owing specifications :- Power Output 500W + 500W Max., 350W + 350W RMS at 10% THD 300W + 300W RMS at 5% THD, 280W + 280W RMS at 2% THD, Output Regulation ≤ 2 dB, no load to full load at 1kHz, Input Channels Mic/Aux: 6 × Mic 0.6mV/4.7kΩ, 2 × Aux 100mV/470kΩ tereo Music Mode: L/R 200mV/100kΩ, Line L/R 1V/20kΩ, Frequency Response 50-15,000Hz ±3dB, Signal to Noise Ratio 60dB, Tone ControlsBass: ±10dB at 100Hz, Treble: ±10dB at 10kHz, Output Preamp 200mV/600Ω, Line 1V/1kΩ , Speaker OUTPUT 4Ω, 8Ω, 70V & 100V for each zone, DIGITAL PLAYER MP3 Player with USB, SD and MMC Card Reader with LCD display and remote control, Bluetooth, Power Supply AC: 220-240V 50/60Hz DC: 36V (3×12V Car Battery), Power Consumption AC: 1500VA DC: 13A. Resettable circuit breaker for protection against overload and short circuit. Make:- Ahuja/ Sony/Yamaha/amperes. |
| 206 | SITC IP65 25 watt 100 volt plastic cabinet PA Sound Projector speaker on existing pole including all mounting hardware with following specifications:- INPUT POWER 25W RMS, POWER TAPS on 100V 25/20/15/10/5W, IMPEDANCE 400/500/670/1k/2kΩ, FREQUENCY RESPONSE 120-15,000Hz, SPL at 1kHz (1W/1m) 93dB, DIMENSIONS Ø183 × H215 mm, ‘U’ type powder coated mounting bracket Make:- Ahuja/ Sony/Yamaha/amperes. |
| 207 | Supply installation testing & Commissioning of ISO certified company 30.5M Flag mast. Mast shaft shall be in three sections, hot dip galvanised by single dipped method and suitable for wind velocity as per IS 875 with FRP dome. System for Raising Lowering of Flag. It Shall have double drum winch, 6mm dia galvanised wire rope and integral power tool for the raising and lowering of Flag. Suitable Control Panel shall be provided for reversing operation of Power tools Motor Mast shall be suitable for Indian Tri Color Flag Size 30Ft X 20Ft. Mast shall be PU painted. Mast head frame assembly with full cover, including 1 No. LED 10 Watts aviation obstruction lights, double drum type self sustaining winch, integral power tool accesible from door with padlocking arrangement ( winch motor with control circuit) hot dipped galvanised heavy duty pipe lightening finial,, trailing cable for aviation light , including outdoor type control panel for auto on / off, reverse / forward motor operation. The mast is constructed from mild steel plates (as per IS 5986 Gr. 510 ) cut and folded to form a polygonal section, telescopic jointed and welding as per BS 5135. OEM must have inhouse PU paint facility. OEM Must have Type test certificate for wind tunnel test for mast fixtures. complete in all respect. The complete work shall be supervised and certified by the manufacturers for satisfactory supply, erection, testing and commissioning of high mast. All as per pre approved by Engineer in charge. Material Cunstruction:- IS 2062 grade E350 / BS EN 10025 or Equivalent having minimum yield strength of 350 N/Sq. mm. Top/ Bottom (diameter of Mast):- 150/540 mm. Thickness of Section (Top-middle-bottom):- 3-4-4 (mm). Thickness of Galvanisations (Min.):- As per BSEN ISO 1461 (For Steel ≤ 3 mm- 55 Microns & For Steel > 3mm to ≤ 6 mm - 70 Microns). Diameter of Base Plate (Min.):- 730 mm. Thickness of Base Plate (Min.):- 30 mm. Nos of foundation Bolt sand size:- 12 Nos and 30 mm Dia. PCD of Foundation bolts (min):- 635 mm. Bolt Length/Grade/Tensile Strength:- 1200mm/ EN 8 Grade Minimum tensile strength 600 N/mm2. Winch:- Nos. of Drum (Drum/Winch):- 2, Capacity (Min.):- SWL 500Kgs, Wire Rope (Nos./Thickness):- 2 continuous/6mm, AISI 316. All as per pre approved by Engineer in-charge. Make:- Bajaj/ Valmont/ Skipper/transrail/Utkarsh |
| 208 | Supply and Fixing of national flag of size 20Ft X 30Ft in 100% knitted Polyester (140gsm), with reinforced super-strong nylon webbing on all 3 sides & rope/toggle sleeve. |
| 209 | Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level.In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc Depth upto 1.5 m |
| 210 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 211 | Brick work with FPS bricks of class designation 75 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 212 | Plastering with cement mortar (1:3) on Brick/stone work in substructure/ super structure at any height complete as per clause 1312 of MoRT&H specification including all material, labour, scaffolding etc. 12 mm plaster on brick work |
| 213 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Jhunjhunu / Jalore (Red ) |
| 214 | Upto to 1500 Cm2 Tiles Above 3601 Cm2 Slabs Green/Black |
| 215 | Upto to 1500 Cm2 Tiles |
| 216 | Above 3601 Cm2 Slabs |
| 217 | Extra for providing edge moulding to 15-18mm thick Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 218 | Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete |
| 219 | S&F 25 mm sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 220 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. 6.0 Sq. mm 2 core |
| 221 | Plate Earthing as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in-charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR |
| 222 | Providing & Fixing of IP - 65 protected impact resistant polycarbonate / Polysterene enclosures with knock out for cable entry/out including fixing with nut, bolt, fatner etc as required complete in all respect of following sizes.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 180 x 180 x 91 mm |
| 223 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 2 x 1.5 sq.mm |
| 224 | P / L of Double wall corrugated HDPE pipe confirming to IS : 16205 P-24, Stiffness Class 750 N, Externally corrugated and having smooth surface inside with HDPE Coupler, Elbow, Tee at required Depth below the ground for laying cable of following Nominal Outer dia. MFR Test report from NABL accrediated is to be submitted.(Excavation of Earth & Back filling with compaction is to be Paid Extra)All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR. 50 mm |
| 225 | P & F of IP 55 protected light controlled switch based on infrared sensing and daylight with built in over load protection, timer to switch OFF at preselected time. Switch shall have 7 day power backup without hampering of preset time and over ride facility formaintenance purpose Suitable for 3 kw load direct lighting load (single phase) |
| 226 | Supply and fixing of Selfie point 9'' thick Letters structure made of 4 mm thich white (code 040) ackerlic sheet top and sides & with 4 mm clear ackerlic sheet (of desired colour) on front of the letter and 3 mm ACP sheet at backside to give strength including water proof LED modules and SMPS. (approx height of letters is 3 feet and proportionally width of each letter/ logo/heart Shape made by letter of love) Letter will be in English or Hindi as per requirement and as per direction of engineering incharge. |
| 227 | Supply and fabrication &fixing of STAINLESS STEEL 304 GRADE STAINLESS STEEL PIPES,FLATS,STRIPS of required size and length and shape with required polishing etc ( minimum 16 Gauge or higher to be use). AS PER INSTRUCTION OF ENGINEER INCHARGE |
| 228 | Supply and fixing of Glow sign boards just like Selfie point made of 2'' thick and 2.5\\" to 4.5\\" width (width and height of the letter according to the aspect ratio of the frame) Letters structure of 2 mm thick white (code 040) / any other colour acrylic sheet with 3 mm ACP sheet at backside cut in same shape and size of the letter including water proof LED modules and SMPS. (outer to outer area of the complete Frame / Board where letters are installed will be considered in Measurements) |
| 229 | SITC and Programming of Content Program Controller, 2X512 Dual universe with digital display Secure Digital (SD) card drive for flexible show storage ,USB2.0 interface for downloading shows and configuring from PC,-Flexible, adaptable mounting options , Should be provided with light show authoring software, Powered with 5-5.5V DC power supply, Minimum five configurable effects,Using light show authoring software to select from standard to minimum five effects, adjust effect settings such as color, speed, and brightness. Compatible with System complete in all respect to fullfil the purpose, (with Three years warranty). |
| 230 | SITC of IP65 constant voltage and constant current power drive of output power 200W suitable for input 110-240V AC 50 Hz and 24V DC output and overoltage/overcurrent/short circuit protection and surge protection of minimum4Kv |
| 231 | High Jet Fountain System – Complete set comprising7.5 HP submersible pump, Lubi / Flotek or equivalent make, suitable for continuous fountain operation with mounting stand and accessories.Provided with heavy-duty SS mesh suction filter manufactured by RWCF for protection against debris and foreign particles.Includes 3\\" SS304 High Jet Nozzle by RWCF with 15° adjustable arrangement for accurate jet alignment.Nozzle designed to produce a strong, stable and impressive vertical high-water jet.Complete with 4 Nos. 100W IP68 DMX RGB PAR Lights by RWCF, suitable for underwater operation. Lights shall operate on 24V DC with DMX-controlled RGB colour mixing, dimming and dynamic effects.Complete assembly shall include required mounting arrangement and accessories for pump, nozzle, filter and lights. |
| 232 | Arc Jet Fountain System – Complete set comprising 5 HP submersible pump, Lubi / Flotek or equivalent make, suitable for continuous fountain operation with mounting stand and accessories.Provided with heavy-duty SS mesh suction filter manufactured by RWCF for protection against debris and foreign particles.Includes 2\\" SS304 High Jet Nozzle by RWCF with suitable mounting and alignment arrangement.Nozzle designed to produce a smooth, stable and visually attractive arc water effect.Complete assembly shall include required mounting arrangement and accessories for pump, filter and nozzle. |
| 233 | Finger Jet / Sunburst Fountain System – Complete set comprising 2 HP submersible pump, Lubi / Flotek orequivalent make, suitable for continuous fountain operation with mounting stand and accessories. Provided with heavy-duty SS mesh suction filter manufactured by RWCF for protection against debris and foreign particles.Includes 1.5\\" SS304 Finger Jet / Sunburst Nozzle by Dhyani Technologies with suitable mounting and alignment arrangement.Nozzle arrangement shall be designed to produce an attractive Finger Jet / Sunburst water pattern with uniform water distribution.Complete with 8 Nos. 24V DC, 27W SS RGB underwater lights by Dhyani Technologies for colourful illumination of the water effect.Lights shall be suitable for continuous underwater fountain operation with RGB colour-changing capability. Complete assembly shall include required mounting arrangement and accessories for pump, filter, nozzle and lights. |
| 234 | 11' Dia Ring Fountain System – Complete circular fountain ring fabricated from 3\\" GI pipe, suitable for continuous fountain operation and uniform water distribution.Ring shall be equipped with 48 Nos. 3/8\\" adjustable fountain nozzles for accurate jet alignment and formation of a uniform circular water pattern.Complete with 3 HP submersible pump, Lubi / Flotek or equivalent make, with suitable mounting stand and required accessories.Provided with suitable SS mesh suction filter by RWCF for protection of the pump and nozzles from debris.Includes 16 Nos. 24V DC, 27W SS RGB underwater lights by RWCF for colourful illumination of the ring fountain.Lights shall be suitable for continuous underwater operation with RGB colour-changing capability.Complete fountain setup shall include required pipe fittings, nozzle mounting, pump arrangement, lighting arrangement and installation accessories. |
| 235 | Chasing Jets Fountain System – Complete setup comprising 30 Nos. individually controlled chasing water jets mounted along approximately 75 ft long, 6\\" GI distribution pipe for dynamic sequential water effects.Each jet shall be equipped with 1.5\\" solenoid valve for fast and accurate ON/OFF water control as per programmed sequences.Jet arrangement shall be designed to create chasing, running, wave and sequential fountain patterns with uniform water distribution.Complete with 30 Nos. 24V DC, 27W SS RGB underwater lights by RWCF for individual colourful illumination of each jet.Lights shall be controlled through suitable DMX decoders, enabling RGB colour mixing, dimming and synchronized dynamic lighting effects.System shall include required DMX/power cables, underwater connections, fittings and mounting accessories for reliable fountain operation.Complete chasing jet assembly shall be suitable for integration with the DMX-based fountain control and show programming system. |
| 236 | Musical Fountain Control Panel & Show System – Complete VFD-based fountain control panel with required VFDs, switchgear, protection devices and internal wiring for reliable pump operation.Panel shall include DMX-based control system for synchronized operation of pumps, solenoid valves, RGB lights and other fountain effects.Complete with SyncD Fountain Show Software – Lifetime License for professional music-synchronized fountain programming and show playback.Includes 30 minutes of customized song choreography/programming as per the approved fountain layout and available water effects.System shall be supplied with a required specification PC configured with SyncD software and necessary interfaces for fountain show control.Complete with sound system comprising 4 Nos. 500W speakers with suitable amplifier for clear and powerful audio playback.Complete system shall be integrated, tested and configured for synchronized music, water and lighting show operation. |
| 237 | Floating Fountain System – 80' x 15' – Complete floating structural setup designed to support the entire fountain equipment safely over the waterbody.Floating structure shall be suitably fabricated and reinforced for mounting of pumps, fountain nozzles, pipelines, lights, cables and associated equipment. System shall include required floats, structural framework, supports, clamps, brackets and mounting accessories for stable operation. Complete arrangement shall be designed for proper load distribution, buoyancy, balance and accessibility for maintenance. Scope includes assembly, positioning, equipment mounting, alignment and interconnection of the complete floating fountain system. Includes required installation and execution at site, including testing and final adjustment of the floating setup. Complete system shall be securely positioned and commissioned for reliable operation of the 80' x 15' floating musical fountain installation. |
| 238 | The work shall comprise design, engineering, fabrication, supply, transportation, installation, testing and commissioning of one complete modular platform decorative illuminated water display assembly having an overall diameter of approximately 2400 mm (8’-0”), suitable for continuous operation in an, water body. of round shape minimum 8' feet dia at which the unit shall be placed. It should be made of non corrosive material and round shape have capacity to make the whole unit float in the lake. platform shall be manufactured from high-strength Marine Grade FRP buoyancy modules with adequate load-bearing capacity to support the complete electro-mechanical assembly while maintaining proper buoyancy and stability during operation. The Supporting Accessories inside the floater Should be of SS 304. All the fixtures and Fitting on and Inside floater Should be of SS304.The Floater .Should be Light in weight but the WCC of paltform should be Min. 400 Kgs floater height should be minimum 12\\" in height and at down side of paltform centre hole should be there for flench and motor Attachement. |
| 239 | The decorative superstructure shall consist of multi-layer Lotus profile petals fabricated from premium quality hand-moulded Fibre Reinforced Plastic using UV-stabilized gel coat finish. The petals shall be structurally reinforced and securely mounted on an internal framework to withstand outdoor environmental conditions .Fixing of Lotus shape leaves in 3 step minimum 22-27 petal of lotus attched with ss structure all three step should have gap in between to set lights between leave petals. it which should look like orignal lotus and should be fixed on floating unit with complete ss structure for attachement. lotus Should not be less than 6 feet in dia. Platform of lotus shape at which centre jet. unit shall be placed. It should be made of non corrosive material. Made up by FRP work. The lotus should be made by Gelcoat, Surface Matt, And 2 layers of Fibreglass matt. The whole leaves of lotus should be Glossy and finished. |
| 240 | The internal supporting framework shall be fabricated from Stainless Steel Grade 304 tubular members, plates and brackets of adequate thickness. All structural members shall be welded, machined and rigidly connected to ensure vibration-free performanceSupply And Fixing Joint system should be made with SS 304, All Parts of Round Uncurler Should be made with SS 304 with Bottom Flench System to fited on the top of Booster and top Flench System for Nozzle. The work of Uncurler is attach floater and motor together and make it a single unit and to give strength to whole unit in water and during running of water |
| 241 | Providing and filling of high-density closed-cell Polyurethane Foam insulation within the hollow cavities of prefabricated modular FRP platform assembly of approximately 2400 mm overall diameter, by controlled pressure injection/pouring process to achieve uniform density, enhanced buoyancy, structural rigidity, water ingress resistance and long-term dimensional stability. The polyurethane foam shall be CFC-free, moisture-resistant, non-biodegradable, self-extinguishing grade, having minimum density of 40 ± 5 kg/m³ or as approved, complete with cavity sealing, finishing and all labour, materials, equipment, consumables and incidental works complete in all respects. |
| 242 | Providing, fabricating, supplying, installing and fixing heavy-duty Stainless Steel (Grade SS-304) structural support pedestal assembly below the modular platform, engineered to provide stable bearing support during seasonal or operational fluctuations in water level. The support assembly shall be designed to safely withstand the self-weight of the complete structure together with all mounted hydraulic, electrical and decorative components, while preventing excessive deformation, impact loading or localized stress on the buoyancy modules. The assembly shall consist of SS tubular sections, base plates, stiffeners, gusset plates, bracing members and all necessary structural reinforcements, complete with TIG/MIG welding, grinding, polishing, alignment and corrosion-resistant finish. The support system shall ensure smooth resting of the floating unit on its bearing legs during low water conditions, maintaining structural stability, preventing direct contact of the FRP floating body with the ground and protecting the complete assembly against damage. The item shall include all necessary fasteners, anchor plates, lifting provisions, fabrication, transportation, erection, testing, alignment and commissioning, complete in all respects as directed by the Engineer-in-Charge. |
| 243 | Providing, fabricating, supplying and fixing SS-304 decorative architectural ring assembly over the platform lotus structure, comprising peripheral and central ring profiles for defining individual FRP lotus petals and maintaining uniform recessed spacing. The ring assembly shall also function as an integrated water manifold for mounting nozzles and concealed IP68 LED lighting fixtures, providing structural support as well as uniform illumination of the lotus petals. The complete assembly shall be fabricated from SS-304 sections with necessary brackets, supports, welding, polishing, fasteners and all accessories, complete in all respects as per approved design and directions of the Engineer-in-Charge. |
| 244 | Fixing one centrally mounted Precision engineered verticle projection Nozzel of minimum 450 mm (approximately 1.5 ft) overall height, designed to produce a stable, high-rise vertical water column. The nozzle shall be precision-machined from and rigidly mounted on the central structural support/manifold. The discharge orifice shall be hydraulically designed to achieve a smooth, non-turbulent and symmetrical jet pattern. The ultimate height shall depend upon the pump discharge pressure, hydraulic head, flow rate and the calibrated nozzle orifice diameter. The item shall include all SS fittings, adaptors, reducers, couplings, alignment, testing and commissioning, complete in all respects as per approved design and the directions of the Engineer-in-Charge |
| 245 | Providing, supplying, installing, testing and commissioning of 36 Watt RGB Underwater LED Luminaire, IP68 protection class, suitable for continuous submerged operation, housed in precision-machined Stainless Steel Grade SS-304 body with high-strength toughened clear glass diffuser. The luminaire shall be factory resin encapsulated (epoxy filled) to provide complete waterproof sealing, moisture protection and long-term durability. The fitting shall incorporate high-efficiency RGB LED modules with uniform light distribution, low power consumption and extended service life. The luminaire shall operate on safe low-voltage supply through a 4-core, 1.5 sq.mm flexible PVC insulated, copper conductor submersible cable conforming to relevant IS specifications, complete with waterproof IP68 cable glands, stainless steel mounting brackets, connectors, hardware and accessories. The luminaire shall be suitable for integration with RGB controller/DMX control system for colour changing, dimming and programmable lighting effects. The item shall include all labour, testing, commissioning and accessories complete in all respects. |
| 246 | Providing, supplying, installing, testing and commissioning of 9 Watt RGB Underwater LED Luminaire, IP68 protection class, suitable for continuous submerged operation, housed in precision-machined Stainless Steel Grade SS-304 body with high-strength toughened clear glass diffuser. The luminaire shall be factory resin encapsulated (epoxy filled) to provide complete waterproof sealing, moisture protection and long-term durability. The fitting shall incorporate high-efficiency RGB LED modules with uniform light distribution, low power consumption and extended service life. The luminaire shall operate on safe low-voltage supply through a 4-core, 1.5 sq.mm flexible PVC insulated, copper conductor submersible cable conforming to relevant IS specifications, complete with waterproof IP68 cable glands, stainless steel mounting brackets, connectors, hardware and accessories. The luminaire shall be suitable for integration with RGB controller/DMX control system for colour changing, dimming and programmable lighting effects. The item shall include all labour, testing, commissioning and accessories complete in all respects. |
| 247 | Providing, fabricating, supplying, installing, testing and commissioning of a heavy-duty mooring and anchoring system for the modular floating decorative water display assembly, designed to maintain the floating unit in its designated position under varying hydraulic and environmental conditions. The anchoring arrangement shall comprise anchor brackets/lugs integrally fixed to the structural framework, connected with high-strength SS wire rope/chain through SS shackles, swivels, turnbuckles and corrosion-resistant fastening accessories. The system shall be anchored to suitable to resist displacement due to wind loads, wave action, operating fountain thrust and fluctuations in water level, while permitting controlled vertical movement of the floating assembly. The complete anchoring arrangement shall be designed to prevent drifting, rotation or lateral displacement of the floating platform without imposing excessive stress on the buoyancy modules or structural frame. The item shall include anchor lugs, guide supports, chains/wire ropes, shackles, turnbuckles, anchor blocks, installation, alignment, testing, commissioning and all labour, materials, tools, tackles and incidental works complete in all respects as per approved design and the directions of the Engineer-in-Charge. |
| 248 | Control voltage driver Supply and fixing of control voltage driver (CVD) for LED lights (12 volt) as required. |
| 249 | LED LIGHT CONTROLLERDesigning, supply erection, commissioning and testing of programmable colour changing system with 6 station changing option |
| 250 | Mono submersible vertical pumpset of 12 HP 380-440v 50 cycles supply with foundation bolts and 3 core PVC flexible copper conductor double insulated cable up topanel Box.(Max 100 Mts.) |
| 251 | Supply & Installation Heavy Duty Stainless Steel water filter for pumpset . |
| 252 | Supply & Installation weather proof control panel made of CRC sheet with proper gears like motor Starter, air contractor, Kit kat, connectors, MCB and all required approved make components for pump and SMPS, control box and all required fittings for RGB Led Lights. |
| 253 | Necessary pipe work of GI ‘B’ class pipes and all required fitting, manifolds, GM valves, SS nut bolts etc. |
| 254 | Sculpatur in Black Bhaslana Marble height 5 ft (60\\") Carved and polished inculding freight& packaging inauguration as per given drawing Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 31, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender