Tender For Special Repairs To Toilet Flooring, Water Supply And Sanitary Arrangements To First Floor In Water Analysis Lab And Office Building In Regional Public Health C Us At Coimbatore In Coimbatore District.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
16 Nov 2026
0 days left
EMD
2500
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Coimbatore → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Toilet Flooring, Water Supply And Sanitary Arrangements To First Floor In Water Analysis Lab And Office Building In Regional Public Health C Us At Coimbatore In Coimbatore District.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling clearing away the damaged BRICK WORK IN CEMENT MORTAR and carefully stacking materials useful for reuse etc, as directed by the departmental officers as per standard specification |
| 2 | Dismantling clearing away the damaged Floor finish and dadooing walls in cement mortar with mosaic tiles / glazed tiles / cuddapah slabs and carefully stacking materials useful for reuse etc, as directed by the departmental officers as per standard specification |
| 3 | Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush.Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete. |
| 4 | Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. FOR SUPERSTRUCTURE IN FIRST FLOOR. |
| 5 | Construction BRICKWORK in cement mortar 1:5 (One cement and five M - sand) using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge. |
| 6 | FOR SUPERSTRUCTURE IN FIRST FLOOR. |
| 7 | Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 20mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 8 | Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used , hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers |
| 9 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work |
| 10 | Flooring with Self designed colour ceramic tiles of size 305 X 305 X 6mm and variety conforming to IS 15622 laid over cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 11 | Dadooing walls with following best approved quality, colour glazed tiles conforming to IS 15622 of size 300 X 450 X 8mm in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 12 | Supplying. Fabricating and fixing of M S GRILL for open court yard grill, grill work to doors, windows and ventilators with required size and angles including with necessary M.S. Channels, ' L ' angles, M.S. Plate as per the approved special designed including cost of materials and labour charges for cutting angle, welding charges including cost of welding rod conveyance charges at site of work including cost of one coat of red oxide primer etc., complete and as directed by the departmental officers. |
| 13 | Supplying and fixing of PVC ready made WATER TANK of 2000 Litres capacity of best and approved quality with ISI specification and having inlet,outlet, overflow and clearing pipe arrangements and labour charges for fixing in position with all necessary accessories and transporting at site of work etc., complete complying as directed by the departmental officers. |
| 14 | supplying and fixing of marble of 0.61*1.22m.,18/20mm thick in all floors for urinal partition including for labour charges for fixing and polishing etc., |
| 15 | Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with \\"P\\" or \\"S\\" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works). |
| 16 | Supplying and fixing in position best quality and approved make Indian made white glazed earthernware wash hand basin of size 550 x 400mm without pedestal with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia \\"B\\" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works). |
| 17 | Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.) |
| 18 | Renewing and fixing in position 15mm dia brass CP screw down tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works) |
| 19 | Renewing and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 5.5mm thick mirror of size 600 x 450 mm, Shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) |
| 20 | Supplying and fixing in position best quality P.V.C. SOIL / WASTE PIPES of following sizes having I.S.I mark and providing leak proof joints including fixing to walls with Specials / PVC /MS. clamps etc., and making connection to all sanitary fittings,dismantling the masonry / RCC works wherever necessary and making good the dismantled portion to original condition etc., complete complying with standard specification.[The PVC pipe should be got approved by the Executive Engineer before use on works.] |
| 21 | 110mm diametre PVC SOIL PIPE [ 6Kg / Cm2] |
| 22 | 75mm diametre PVC SOIL PIPE [ 6Kg / Cm2] |
| 23 | Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). |
| 24 | 110 mm diametre PVC PLAIN ELBOW. |
| 25 | 75 mm diametre PVC PLAIN ELBOW. |
| 26 | 110 mm diametre PVC TEE. |
| 27 | 75 mm diametre PVC TEE. |
| 28 | Supplying, laying and jointing UPVC pipes of Class 6 (having working pressure of 12.50 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety conforming to BIS of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works - Internal water supply. ABOVE GROUND LEVEL. |
| 29 | 32mm diametre UPVC Pipe |
| 30 | 25mm diametre UPVC Pipe |
| 31 | 20mm diametre UPVC Pipe |
| 32 | Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements complete complying as directed by the department officers as per standard specification.Note:- Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separte provision for fixing UPVC specials needs to be allowed. |
| 33 | 25mm diametre U.P.V.C ELBOW. |
| 34 | 25mm diametre U.P.V.C TEE. |
| 35 | 20mm diametre U.P.V.C ELBOW. |
| 36 | 20mm diametre U.P.V.C TEE. |
| 37 | 25 X 20mm diametre U.P.V.C REDUCER. |
| 38 | Supplying and fixing the following sizes of new GUN METAL WHEEL / GATE VALVE (HEAVY TYPE) of approved quality and good variety excluding the fixing charges but including necessary cutting and threading of G.I. pipes for jointing the G.I. specials and providing two coats of painting with good quality and approved variety of anti-corrosive paint over a coat of red oxide primer coat in the case of pipe line above ground level and one coat of tarring in the case of pipe line below ground level etc., complete. |
| 39 | 25mm diametre G.M.. WHEEL VALVE. |
| 40 | 32mm diametre G.M.. WHEEL VALVE. |
| 41 | Supplying and fixing in position of PVC DOOR SHUTTERS using 19 gauge 19mm MS Sq. tubes for styles and outer frames. 15 mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The overall size of styles shall be 50 x 30 mm. The overall size of top rail, lock rail and bottom rail shall be 75 x 30 mmThe overall size of frames sshall be 50 x 45 mm, with suitable rabate for housing the shutter. etc., complete as directed by the departmental officers. Solid panel PVC door with frame |
| 42 | Painting Old Plastered Wall Surface with Two finishing coats of ready mixed INTERIOR (Emulsion) of approved quality and colour over the existing wall in all floors etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 43 | Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat on old cement plastered wall surface ect., complete complying with standard specification and as directed by the departmental officers. |
| 44 | PAINTING OLD WOOD WORKS with TWO coats of synthetic enamel paint of approved quality and colour over a priming coat with approved quality of white primer in all floors. The rate is inclusive of cost of all materials and labour, brushes and scaffolding charges etc., complete complying with standard specification. (The paint to be used should be got approved by the Executive Engineer before use on work) |
| 45 | GST 18% (CGST AT 9% + SGST 9%) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
TodayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender