Tender For Repair/Maint & Replacement Of Ht Electric Installation And Distribution, Solar Water Heater, Dg Set And Air Conditioner, Refrigeration, Deep Freezers And Other Connected Works At Solan And Subathu Under Ge Kasauli
Tender Overview
Project Description
Tender for Repair/Maint & Replacement Of Ht Electric Installation And Distribution, Solar Water Heater, Dg Set And Air Conditioner, Refrigeration, Deep Freezers And Other Connected Works At Solan And Subathu Under Ge Kasauli
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth and getting out in hard/dense soil including dressing/trimming sides and levelling/grading and ramming of bottom of excavation complete all as specified. |
| 2 | Excavation in trenches not exceeding 1.5 metre wide and depth exceeding 1.5 metre and not exceeding 3 metre and getting out in hard/dense soil including dressing / trimming sides and levelling/grading and ramming of bottom of excavation complete all as specified. |
| 3 | Returning, filling in including spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25 cm thick, filling back in trenches after cables have been laid and tested, poles, stays, struts have been erected and tested complete all as specified. |
| 4 | Removing of surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above starting point complete all as specified. |
| 5 | Supplying & fixing of double walled corrugated HDPE duct pipe,SN-6 of nominal diameter 110 mm manufactured from high density polyethylene, confirming to IS-14930 (Part-II) of approved colour with fittings for cable protection complete all as specified and direcetd. |
| 6 | Taking down old unserviceable poles of any description and material & Labour for Steel tubular swaged poles with cast iron base plate, finial, taper plug, bolts, nuts and screws type 410 SP-55, 11.0 metres long, duly painted with two coats of aluminium paint over a coat of red oxide primer and providing 30 cm wide alternate black and yellow strips up to 1.5 meter from Ground Level complete all as specified. Note- Excavation, earth work and PCC shall be measured and paid separately under relevant items. |
| 7 | Material & Labour for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundation of electric poles, for base of pole , struts complete all as specified. |
| 8 | Material & Labour for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) in foundation of electric poles, mass filling complete all as specified. |
| 9 | Material & Labour for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) in coping of electric poles complete all as specified. |
| 10 | Taking down old unserviceable Switch air break gang and material & labour for Switch air break gang operated out door HT 11 KV triple pole mechanically operated mounted on HT insulators (12 Nos insulators) type and MS galvanised steel frame with operating mechanism worked from ground level including operating rod for current rating upto 400 Amps, 11000 volts and electric rubber hand gloves 11 KV complete with locking arrangements MS clamps, bolts, nuts and washers etc. including fuse barrels of required capacity to suit the load at site including two coats of aluminium paint over a coat of red oxide primer on MS work complete all as specified. |
| 11 | Material and Labour in repair lightening arresters expulsion type complete with all fittings, transmission class, discharge capacity 65 kilo amp 11000 volt including brackets, clamps, nuts and washers complete all as specified |
| 12 | Material & Labour in replacement, Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified. |
| 13 | Material and Labour in replacement for GI pipe, light grade 100 mm bore, IS Marked for protection to cable along the pole/across road crossing/passing through culvert complete all as specified. |
| 14 | Material and Labour for Cable jointing kit for 11 KV (Earthed) grade cable for outdoor end termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95 sqmm complete all as specified and directed |
| 15 | Material & Labour for Cable jointing kit for 11 KV (Earthed) grade cable for indoor end termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95 sqmm complete all as specified and directed. |
| 16 | Material & Labour for Cable jointing kit for 11 KV (Earthed) grade cable for outdoor straigth through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95 sqmm |
| 17 | Material & Labour for XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured,electric power cables (heavy duty) with aluminium conductor, 11000 volts grade, earthed, cross sectional area 95 sqmm 3 core laid in trenches including testing complete all as specified and directed |
| 18 | Material & Labour for Painting of HT steel tubular pole 11 meter long, by applying two coat of aluminium paint after scraping / brushing and cleaning the rust on pole and cross arms. Aluminium painting will be done on pole above 1.5 metre height from ground level and balance 1.5 mtr from ground level will be painted by alternate layer of black and yellow enameled paint (30 Cms each). Pole Nos will be written on pole by black paint in yellow circle of 150mm dia, complete, all as specified and directed by Engr-in-chargeNote:- Only one coat will be applied at one time and payment at 50% of coated rate to be applied at the first time of first coat. Second coat is to be done more than 30 days after first coat. |
| 19 | Material & Labour for overhauling of step down outdoor/indoor transformer 11/0.433 KV (400-750 kVA) by disconnecting HT/LT terminals, decanning transformer oil removing sludge, cleaning of HT/LT bushings to remove dust particles/dirt etc. Cleaning the core and winding with compressed air and re-assemble complete including replacement of copper windings, copper washers, rubber bushes of HT/LT bushings replacement of cork sheet of 6 mm thick suitable for transformer top cover, terminal boxes refilling the transformer oil and toping up with new transformer oil and centrifuging to achieve the dielectric strength upto 50KV painting with two coat & synthetic enamel paint over a coat of red oxide primer after preparation of painted surfaces of transformer and testing and recommissioning on load etc complete for the transformers of following rating:- (Dehydration of transformer oil by filtration, topping up transformer oil, shall be measured and paid separately as supply only under respective items) complete all as specified and directed. |
| 20 | All as per item No-1.19 above but capacity of transformer 100 KVA to 250 KVA complete all as specified and directed by Engr-in-charge. Please Enable Macros to View BoQ information |
| 21 | All as per item No-1.19 above but capacity of transformer 100 KVA to 250 KVA complete all as specified and directed by Engr-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Tender Published
Tender notice published.
CompletedBid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayBid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender