Tender For Special Repair To Bldg No P-148 (Cook House) Of Inf Bn-Ii At Mil Stn Abohar.
Tender Value
19.31 Lakhs
Estimated cost
Bid Submission
21 Nov 2026
18 days left
EMD
38700
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Fazilka → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No P-148 (Cook House) Of Inf Bn-Ii At Mil Stn Abohar.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (reinforced) in roof , floors (other than ground floor ), beams, staircase, landing,chajjas and similar suspepnded work |
| 2 | M & L mild steel TMT bars 10mm dia or over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as in column, beam etc . |
| 3 | Reinforced cement concrete nominal mix Type B1 1:1.5:3( 20mm graded stone aggregate) in slab supported on walls,beams and columns in floors,roofs,landings,balconiies,deck slabs and in shelves and the like all as specified and directed. (form work & reinforcement measured separately). |
| 4 | M&L for Formwork to soffits of suspended slabs, such as roof slabs, floor slabs landing and similar work not exceeding 200mm thick (Horizontal & sloping) fair finished surfaces (Note- Steel props to be use). |
| 5 | M&L for Formm work to edges of concrete flates treads breaks in floors, window cill concrete railing, opening in convert valley floor and roof exc 10 cm but n.exc 20 cm wide and sides RCC/PCC band in walls. |
| 6 | Demolition of cement concrete (un-reinforced) in floors / pavings, (below or above ground level) and of any description and in any position not otherwise specifically provided for all as specified . |
| 7 | Material & labour for 75mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in hard standing ,plinth protection/path etc, laid in suitable panels not exceeding 3.00 m length finished even and smooth without using extra cement with 10mm Joints filled with bituminous sealing compound of grade ‘A’/bitumen mastic filler/sealant complete all as specified and directed by Engineer-in-Charge. |
| 8 | Forming contraction(Dummy)joints 65mm deepx10mm wide filled with sealing compound grade 'A' complete all as specified and directed. |
| 9 | Demolition of brick work built in cement mortar all as specified . |
| 10 | M&L for Brick work using fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge. |
| 11 | M & L for brick work in half brick thick wall using fly ash bricks straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge. |
| 12 | Dismantling of floor hearth or wall tiling including cement mortar bedding ( but not backing) and rubbish off the permices. |
| 13 | Material and labour for 7 to 8 mm thick non-skid ceramic colour (light shade) joint free tiles with matt finish premium quality, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floor over screed bed in CM 1:4 , set and jointed confirming to IS-15477:2004 including necessary cutting as per site requirement, complete all as specified and directed by Engineer-in-Charge. |
| 14 | Material and labour for vitrified coloured tiles (approved shade) of size 600mm x 600mm having thickness 8 to 9 mm premium quality , straight edge, stain free, glossy finish, square marbonite, laid as in floor over screed bed in CM 1:4 , set and jointed w confirming to IS-15477:2004 and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, complete all as specified and directed by Engineer-in-Charge. |
| 15 | Ditto all as above item but as in skirting over 10 mm cement screed bed backing ( 1:3) complete all as specified and directed by Engineer - in - Charge. |
| 16 | Material and labour for Providing and Laying Premium (1st) quality, digitally printed straight edge, punched, glazed ceramic rectangle tile in approved shade in coloured tiles 600 X 300 mm and 7 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.Note : Dado should be flushed with the wall plastering. |
| 17 | M & L Machine cut kota stone slab flooring Size not exeeding 600 x 600,18-20 mm thick over cement screed base laid over and including 20mm thick screed bed in cement mortar 1:4 set and jointed with grey cement slurry mixed with pigment to match of the slab including rubbing and polishing complete all as directed. |
| 18 | M & L Machine cut kota stone slab 18-20 mm thick in riser of steps,skirting,dado and pillar over cement screed base laid over 10 mm cement screed bed backing ( 1:3) set and jointed with grey cement slurry mixed with pigment to match of the slab including rubbing and polishing complete all as directed. |
| 19 | Material and labour 16-18mm thickness approved shade granite of minimum size equal to width of slab (not less than 600mm wide, length wise single or two pieces only) machine cut, granite duly factory grinding and polishing and chamfering the outer edges (table rubbed and mirror polished) as in cooking platform and like laid over and including 20mm thick cement mortar (1:4) screed bed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including accomodate the hole for gas pipe complete all as specified and as directed by Engineer-in-Charge. |
| 20 | Taking down chowkats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each all as specified . |
| 21 | Taking down chowkhats or frames with shutters without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each and all as specified . |
| 22 | Supply & fixing aluminium anodised frames/chowkhats, made out of aluminium section powder coated (minimum thickness of powder coating not less than 50 micron) for window, ventilators and aluminium partition with one or more rebates or without rebate including joining cleat for fixing etc., the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and as directed by Engineer-in-Charge.Note :- The weight of each section shall be physically ascertained through a board of officers convened by GE and payment shall be made only after the actual weight at site. |
| 23 | Supply & fixing Anodised aluminium powder coated aluminium (minimum thickness of powder coating not less than 50 micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified |
| 24 | S&F Aluminium (extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified |
| 25 | S & F figured glass 4 mm thick pin head type and glazing with not exceeding 0.50 Sqm including aluminium cleat/rubber beading in each pan complete all as specified and directed by Engineer - in - Charge. |
| 26 | M & L for prelaminated particle board both side with decorative choice laminations exterior grade 19mm in repair kichen cabinate as specified by Engr-in-charge |
| 27 | Supply & fixing powder coated aluminium (minimum thickness of powder coating not less than 50 micron) sliding window three track with frame & two numbers glass shutters using 4 mm thick glass (tinted ) and one number shutter with stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperture 1.61 mm complete window using aluminium powder coated sections including aluminium cleat, PVC track, bearing, handle lock, rubber beading, beading for securing the wire cloth etc complete fittings as approved and directed. Size of aluminium sections for frame and shutters shall be as under :-(A) Three Track Frame :-(a) Bottom frame :- Jindal 2010, Section 20620 or Techno commercial equivalent as approved by GE.(b) Top and vertical frame - Jindal 2010, Section 20621 or Techno commercial equivalent as approved by GE.(B) Shutters(a) Glazing Shutter :-(i) Vertical side, bottom and top section - Jindal 2010, Section 20604 or Techno commercial equivalent as approved by GE.(ii) Vertical middle (interlock) section - Jindal 2010, Section 20605 or Techno commercial equivalent as approved by GE.(b) Wire gauge shutter :-(i) Vertical, bottom and top section - Jindal 2010, Section 20604 or Techno commercial equivalent as approved by GE.Note :- (i) Cost of Glass, wire cloth, three shutter and three track frame alongwith fixtures etc shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. (ii) Measurement for payment shall be the opening area of the window between inner edges of wall. |
| 28 | Supply & fixing aluminium Powder coated grill of approved design/pattern, with approved standard section and fixed to the window frames with CP brass/stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and as directed by Engineer-in-Charge.Note :- The weight of grill shall be physically ascertained through a board of officers convened by CWE and payment shall be made only after the actual weight at site. |
| 29 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: (i) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 30 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 62 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: (i) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 31 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 62 x 150 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: (i) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 32 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf (b) Stainless Steel (304 Grade) Finished Square Tower Bolt 150 mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 150 mm - 2 nos. per leaf(d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf |
| 33 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type glazed/gauge skelton door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with butt hinges with necessary full body threaded star headed counter sunk S.S screws including S&F wire cloth complete all as per direction of Engineer- In- Charge including supply and fixing following items:-(a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf(b) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long - 2 nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf(d) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf(e) Stainless Steel (304 Grade) (natural finish) wire cloth fixing as per manufacture |
| 34 | Supply and fixing stainless steel pipe 25mm bore (as a curtain rod), wall thickness of pipe not less than 1mm and grade SS 202, fixed in position with fixing accessories like Brackets, finial and side holder of same manufacturer complete all as specified and as directed by Engineer-in-Charge.Note : (i) Brackets, finial and side holder shall be measured and paid separately for supply only but the cost for fixing the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.(ii) Cost for screws, rawl plugs as required for fixing shall also shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 35 | Supply only stainless steel 202 grade brackets for fixing of 25mm bore curtain rods complete all as specified. |
| 36 | Supply only stainless steel 202 grade side holder for fixing of 25mm bore curtain rods complete all as specified. |
| 37 | Supply only stainless steel 202 grade finials for fixing of 25mm bore curtain rods complete all as specified. |
| 38 | S & F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples all as specified . |
| 39 | S & F figured glass 4 mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pan complete all as specified . |
| 40 | S & F mild steel 300mm ordinary rat rail rod pattern spring inluding roller and roller plate complete all as specified . |
| 41 | S & F mild steel sliding door, bolts, plate type, stove enamelled black with bright bolt not less than 12mm bore, length of bolt 250mm all as specified . |
| 42 | S & F aluminium tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm long all as specified . |
| 43 | S & F aluminium bow handle stove enamelled black, 150 mm long all as specified . |
| 44 | S&F Floor door stopper of aluminum allow body and tongue, 150mm overall length, anodised, with hard drawn steel spring, fixed in floor. |
| 45 | Material and labour for providing kitchen cabinet and cubboard in required sizes at site made out of 18mm thick PVC sheet (prelam) having one side decorative laminated sheet (for shutter, back side of cabinet, sides of cabinet, partition and shelves etc). All the edges of shutter and front exposed edge of partition/shelves shall be covered with 2mm thick edge bonding tape as per manufacturer. Including all required fixing material such as SS brackets, screws, adhesive etc., including taking out old any type cabinet complete all as specified and as directed by Engineer-in-charge.Note :- (i) The area of each sheet (shutter, back side of cabinet, sides of cabinet, partition and shelves) shall be measured in sqm for payment.(ii) Magnetic catcher, handle/knob, continuous Piano hinges and PVC frame (where required) shall be measured and paid separately under appropriate item of BOQ.(iii) Any other material required for making/fixing/hanging of cabinet shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 46 | S & F Continuous (piano) hinges 30 mm size of brass, bright finish and shape as required all as specified and directed. |
| 47 | S&F Magnetic catcher fixed in with nut,screw washer complete all as specified and directed by Eng-in Charge. |
| 48 | S & F 100mm extuded,brass handles,fabricated type polished for cabinet shutters complete all as specified and directed. |
| 49 | S&F in repair sink made of Stainless Steel 1mm thick kitchen with plug washer and waste including bedding in cement mortar to dwarf wall including fixing contilever brackets connecting union to pipe over all size 685 x 510 mm bowl of size 610 x 460 x 254 mm fixed in repair. |
| 50 | S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm |
| 51 | S & F in repair 15 mm bore bib tap fancy type chromium plated with crutch or butterfly handle screwed down ,screwed for iron pipe all as specified.Make:- Prayag,Ess Ess co and equivalent |
| 52 | S & F in repair 15 mm bore Pillar tap fancy type chromium plated with crutch or butterfly handle screwed down ,screwed for iron pipe all as specified.Make:- Prayag,Ess Ess co and equivalent |
| 53 | S&F 15mm bore stop valve fancy type chromium plated with long shank and cup cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions all as specified and directed. |
| 54 | S & F in PVC connection 15mm size with PTMT nuts of length 450mm all as specified . |
| 55 | S&F squatting pan orissa pattern, vitreous china white of size 580 X 440 mm with integeral foot rest, including necessary lime concrete and CI 'P' trap for WC with cement joint,complete all as specified. |
| 56 | S&F PVC high or low level cistern of 10 litres capacity including 32mm dia. Flush pipe and internal fittings complete all as specified. |
| 57 | S & F in repairs vitrous china wash hand basin coloured top bowl type of size 550x400mm long screwed shank fly nut flange end including cutting for and pinning in granite slab of hole including 32 mm dia chromium plated waste coupling and bottle trap all as specified .(MAKE- Hindware Cat No 91807 range Hi Lites or equivalent in Parryware) |
| 58 | S&F looking mirror 600x450x5 mm thick bevelled edge, of selected quality glass, mounted on 6 mm thick AC board and fixed to wooden plugs with chromium plated screws and washers complete. |
| 59 | S & F in repairs CP Towel rail 20 mm dia 600 mm long superior quality complete all as specified . |
| 60 | S & F soap dish fixed as chromium plated all as specified & directed. |
| 61 | Dismantling water tanks and removing to store of exc 500 nexc 1000 ltr capacity |
| 62 | S & F rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 1000 Litres all as specified and directed by Engineer - in - Charge . |
| 63 | S&F in 20mm Ball brass valves, high pressure, with polytheene float and flynut complete, screwed for iron pipe orr brass ferrule and fixed. |
| 64 | S & F in 20mm bore gunmetal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed all as specified . |
| 65 | Taking down steel tubing 15mm bore and connections complete all as specified. |
| 66 | Supply & fixing of 20mm outer dia CPVC pipes SDR 11 including all fittings Plain/brass threaded CPVC SDR 11 fittings (like Elbow, Tee, Socket, Reducer, Union, Bushing, Step over bends, End cap, End Plugs, one side brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including CPVC solvent cement for jointing complete all as specified and as directed. |
| 67 | Taking down steel tubing 20mm bore and connections complete all as specified and directed by Engineer - in - Charge. |
| 68 | Supply & fixing of 20mm outer dia CPVC pipes SDR 11 including all fittings Plain/brass threaded CPVC SDR 11 fittings (like Elbow, Tee, Socket, Reducer, Union, Bushing, Step over bends, End cap, End Plugs, one side brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including CPVC solvent cement for jointing complete all as specified and as directed.NOTE FOR CPVC PIPES : (i) Pipes inside the buildings shall be fixed concealed and outside the buildings shall be fixed on the surface along wall with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) of suitable size fixed with fasteners/nut bolts, as directed by Engineer-in-Charge. (ii) Bracket, clamp, nut bolt, fastner, slotted channel etc shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on BTD drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. (iii) Cost for cutting chases in wall and making good disturbed surfaces as required shall deemed to be included in the quoted unit rate. |
| 69 | S&F 20 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA) comlete all as specified and directed. |
| 70 | S&F 20mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA) comlete all as specified and directed. |
| 71 | S&F 20mm bore CPVC tank adaptor Brass Threaded comlete all as specified and directed. |
| 72 | S&F 20mm bore CPVC Union Brass Threaded comlete all as specified and directed. |
| 73 | S&F CPVC pipes 40 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings as in walls, ceiling, floor. etc complete all as specified and directed. |
| 74 | Taking down CI/AC/PVC soil waste and vent pipe any radius including all fittings complete. |
| 75 | Supply & fixing 75mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge.Note:- Bracket, clamp, nut bolt, fastner, slotted channel etc shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on BTD drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. |
| 76 | Supply & fixing 110mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, laid in trenches, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. |
| 77 | Supply & fixing 75mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, laid in trenches, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. |
| 78 | Supply & fixing uPVC bends (any radius) grade 'B' suitable for 110mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 79 | Supply & fixing uPVC bends (any radius) grade 'B' suitable for 75mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 80 | Supply & fixing uPVC junction (double T/socket) grade 'B' equal or unequal suitable for 110mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 81 | Supply & fixing uPVC junction (double T/socket) grade 'B' equal or unequal suitable for 75mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 82 | Supply & fixing uPVC grade 'B' multi floor trap 75mm bore and 600mm long with grating including jointing with with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. |
| 83 | Supply & fixing uPVC vent cowl grade 'B' suitable for 80 mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 84 | Supply & fixing uPVC vent cowl grade 'B' suitable for 100 mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 85 | Supply & fixing uPVC reducer socket grade 'B' 110/75mm to 50mm bore complete all as specified and as directed by Engineer-in- charge. |
| 86 | S&F 75mm PVC(SWR) floor trap plain with grating including jointing with solvent cement. |
| 87 | Supply & fixing 32mm bore High density polyethylene pipes (HDPE) of pressure rating not less than 6kg/sqcm laid in wall/floors including necessary cutting of brick works and fix in mortar in CM 1:3 complete all as specified and as directed by Engineer-in- charge. |
| 88 | Material and labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of voids in masonry using chemical emulsion @ one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge. |
| 89 | Material and labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre 300mm apart including drilling depth of holes not less than 300mm and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge. |
| 90 | Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof roof complete all as specified and directed by Engineer-in-Charge. |
| 91 | Dismantling of Brick tiles or terracing tiles, single layer on roofs complete all as specified and directed by Engineer-in-Charge. |
| 92 | M & L for 40mm thick cement concrete type B0 1:2:4 (12.5mm graded aggregate) as in , surface finished even and smooth without using extra cement . |
| 93 | Material and labour for Preparing surface of top roof slab including sides of parapits and cleaned of all foreign materials moss, dust, loose particle etc by wire brushing and applying 10mm thick rendering in Cement Mortar (1:3) on roof concrete surfaces and finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge |
| 94 | Preparation of roof top surfaces, providing and applying UV stable single component smart care damp proof ultra is a fibel reinforced elastomeric liquid applied water proofing membrane formulated with PU hybrid polymers and reinforcing acrylics fibres and having SRI of 106 on top of concrete roof surface in three coats including self-primer at ratio pf damp proof and water 3:1 and coverage @ 1 Ltr/10 Sqm with a thickness of 650 micron. Note : (i) 6 Hrs interval between two coats will be maintained.(ii) The treatment shall be carried out by authorised applicator approved by CWE as per the manufacturer(iii) Payment will be made after providing warranty certificate from the company. |
| 95 | M&L for 25mm thick PCC 1:2:4 type 'B-0' using 12.5 mm graded crushed stone aggregate with a slope of 1:40 complete all as specified and directed by Engineer - in - Charge. |
| 96 | Material and labour for removing loose disturbed or disintegrated old concrete surfaces of RCC beam, ceiling, slab, column, lintel, pardi, railing etc. cleaning thoroughly exposed reinforcement by sand blasting using suitable pump as directed by GE, preparing exposed concrete surfaces to receive guniting, applying one coat of anti-corrosive paint to the exposed reinforcement, supply and fixing welded wire mesh of size 100x100mm of 3mm dia wire and weight not less than 1.37 kg/Sqm and binding with 22 guage mild steel (annealed) binding wire to reinforcement and applying pressure guniting as per IS 6433 in cement mortar (1:3) average thickness 30mm and thereafter 10mm thick rendering in cement mortar (1:3) including mixing of liquid WPC in mortar @ as per manufacturer instruction and finishing the surfaces even and smooth without using extra cement to match the existing surface including removing rubbish material from building and thrown in low lying empty area at any distance out side MD land complete all as specified and as directed by Engineer-in-Charge.Make: M/s Sika India Pvt Ltd/ Fosroc/pidiliteNote :- (i) The finished level of the surfaces shall be matched with the existing surface. (ii) Provision of additional reinforcement steel in case required and ordered shall be measured and paid separately |
| 97 | Taking down cement or cement lime plaster from brick walls etc including raking out joints, hacking for key scrubbing down with water etc. |
| 98 | M&L for rendering 10 mm thick in CM 1:3 on ceiling, finished the surface even and smooth without using extra cement all as specified and directed. |
| 99 | M&L rendering 15mm thick in CM 1:6 on fair face of brick or concrete surface,finished even and smooth without using extra cement complete . |
| 100 | M&L rendering 15mm thick in CM 1:4 on fair face of brick or concrete surface,finished even and smooth without using extra cement complete . |
| 101 | M&L for preparation of newly plastered ceiling surfaces and applying three coat of White wash complete all as specified & directed by Eng-in- Charge. |
| 102 | Material and labour for Preparation of new plastered surfaces and applying acrylic wall putty in internal/external walls/RCC surfaces/soffits of chajjas/roof projections/ cantilevers/balcony/ceilings etc (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving interior/exterior painting complete all as specified and directed. |
| 103 | Material and labour for Preparation and applying 02 coats of interior emulsion paint (light shade) @ 12 sq.m/litre/2 coats by using spray gun to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed. |
| 104 | Material and labour for Preparation and applying 02 coats of exterior emulsion paint (light shade) @ 12 sq.m/litre/2 coats by using spray gun to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed. |
| 105 | M&L for preperation of old wooden surface and applying one coat of synthetic enamel paint over a coat of pink primer complete all as specified . |
| 106 | Material and labour for Preparation of old surfaces and applying one coat of exterior plastic emulsion paint by using spray gun to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc complete all as specified . |
| 107 | M&L for preparation of newly plastered ceiling surfaces and applying one coat of White wash complete all as specified & directed by Eng-in- Charge. |
| 108 | Material and labour for Preparation and applying one coat of interior emulsion paint (light shade) @ 12 sq.m/litre/2 coats by using spray gun to wall surfaces complete all as specified and directed. |
| 109 | M&L for taking down carefully point wiring complete including fixture and fittings from boards/outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. and making good to disturbed area all as specified |
| 110 | M&L for Point wiring complete with ISI marked 2.5 sqmm single core PVC insulated unsheathed cable 1100V grade FRLS with multistranded copper conductor drawn through concealed in wall/ceiling surface and its accessories including PVC rigid concealed conduit heavy duty suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of modular switchs, sockets, fan regulator etc covered with Modular sheet and covers sheet of required size fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat red oxide primer including fixing and 2.5 sqmm copper conductor as earth continuity to connect common earth dolly completed, cost of modular sheet and cover are included in the item rate complete following all as specified (a) One light point/Fan point/Exhaust controlled by one way switch |
| 111 | M&L for Point wiring complete with ISI marked 2.5 sqmm single core PVC insulated unsheathed cable 1100V grade FRLS with multistranded copper conductor drawn through concealed in wall/ceiling surface and its accessories including PVC rigid concealed conduit heavy duty suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of modular switchs, sockets, fan regulator etc covered with Modular sheet and covers sheet of required size fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat red oxide primer including fixing and 2.5 sqmm copper conductor as earth continuity to connect common earth dolly completed, cost of modular sheet and cover are included in the item rate complete following all as specified (b) One 5 pin socket out let 5 amps on the same board with other switches |
| 112 | M&L for Point wiring complete with ISI marked 2.5 sqmm single core PVC insulated unsheathed cable 1100V grade FRLS with multistranded copper conductor drawn through concealed in wall/ceiling surface and its accessories including PVC rigid concealed conduit heavy duty suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of modular switchs, sockets, fan regulator etc covered with Modular sheet and covers sheet of required size fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat red oxide primer including fixing and 2.5 sqmm copper conductor as earth continuity to connect common earth dolly completed, cost of modular sheet and cover are included in the item rate complete following all as specified (c) One 5 pin, 5A socket outlet point on independent board with other switches. |
| 113 | All as per item no. 110 here-in-before but with 4.0 sqmm cable for 1No 16 amps socket outlet point on independent board including 4.0 sqmm PVC insulated unsheathed cable multistranded with copper conductor green in colour as earth continuity conductor all as specified |
| 114 | S&F Modular switch 1 way 6 Amps, 1 module 230 volt AC supply complete all as specified |
| 115 | S&F Modular Socket, 6A - 2/3 pin combined 2 module, 230 volt AC supply complete all as specified. |
| 116 | S&F Modular switch 1 way 16A, 1 module 230 volt AC supply complete all as specified |
| 117 | S&F Modular Socket 6A/16A - 2/3 pin combined, 2 module, 230 volt AC supply complete all as specified. |
| 118 | S&F sheet metal enclosure single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amps MCB complete. |
| 119 | S&F Ceiling rose surface type, 65mm x 50mm three terminals, 3 phase / PVC / polycarbonate isolated body all as specified |
| 120 | Supply and fixing LED lights fitting 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 121 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete withIP 65/66 protection complete. |
| 122 | S&F sheet metal enclosure for VTPN DB's 415 volts 08 way with 200 amps rated bus bar neautral link, earth bar double door with MCCB as incomer complete all as specified |
| 123 | S&F sheet metal enclosure for DB's SPN 230 volts 12 way with 200 amps rated bus bar neautral link, earth bar double door including taking out old us DB complete all as specified |
| 124 | Supply and fixing 415V 16 KA 415 volts MCCB of cap 100 amps following poles and current carrying capacity in the DB including taking out old us MCCB complete with connection testing and commissioning. |
| 125 | Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of cap 32 amps double poles and current carrying capacity in the DB including taking out old us MCB complete with connection testing and commissioning. |
| 126 | Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB including taking out old us MCB Complete with connection testing and commissioning complete all as specified |
| 127 | M&L for submain wiring comprising single core , 2 Runs of 6 sqmm nominal cross sectional area multi stranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade drawing in and including appropriate dia. in surface/recessed PVC conduit and its fittings complete including provision of 1X10 sqmm nominal cross sectional area multi stranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire and using color code as per IS and specified and making good all disturbed work to match the existing complete incl taking down old UNSV sub main complete all as specified and directed by Engr-In-charge.( Note :- Extra length of cables/ wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly) |
| 128 | M&L for Earthing complete with galvanised steel earth plate electrode of size 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 m below normal GL connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers and earth strip protected by 15 mm dia GI pipe medium grade and connected to main distribution board panel/earthing test point all as shown on electrical plate No.3 of SSR Part I and all as specified including testing on completion including taking down old Unserviceable earthing any type all as specified Please Enable Macros to View BoQ information |
| 129 | M&L for Earthing complete with galvanised steel earth plate electrode of size 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 m below normal GL connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers and earth strip protected by 15 mm dia GI pipe medium grade and connected to main distribution board panel/earthing test point all as shown on electrical plate No.3 of SSR Part I and all as specified including testing on completion including taking down old Unserviceable earthing any type all as specified Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 31, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysNov 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender