Tender For Construction Of Office Building For Mananthavady Municipality, Wayanad District, Phase-Iii
Tender Value
Ref. Documents
Estimated cost
Bid Submission
17 Nov 2026
2 days left
EMD
1 Lakhs
Bank guarantee accepted
Document Fee
8850
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Wayanad → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Office Building For Mananthavady Municipality, Wayanad District, Phase-Iii
BOQ
| Sl. No. | Item Description |
| 1 | Civil Work -Building |
| 2 | 15.2.1Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominalconcrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 3 | 5.3Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 4 | 5.33.2.1Providing and laying in position ready mixed or site batched design mix cementconcrete for reinforced cement concrete work; using coarse aggregate and fineaggregate derived from natural sources, Portland Pozzolana / Ordinary Portland/Portland Slag cement, admixtures in recommended proportions as per IS: 9103 toaccelerate / retard setting of concrete, to improve durability and workability withoutimpairing strength; including pumping of concrete to site of laying, curing, carriagefor all leads; but excluding the cost of centering, shuttering, finishing andreinforcement as per direction of the engineer-in-charge; for the following grades ofconcrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cementAll work above plinth level upto floor V levelConcrete of M25 grade with minimumcement content of 330 kg /cum |
| 5 | 5.9.6Centering and shuttering including strutting, etc. and removal of form for:Columns,Pillars, Piers, Abutments, Posts and Struts |
| 6 | 5.9.3Centering and shuttering including strutting, etc. and removal of form for:Suspendedfloors, roofs, landings, balconies and access platform |
| 7 | 5.9.5Centering and shuttering including strutting, etc. and removal of form for:Lintels,beams, plinth beams, girders bressumers and cantilevers |
| 8 | 5.9.7Centering and shuttering including strutting, etc. and removal of form for:Stairs,(excluding landings ) except spiral - staircases) |
| 9 | 5.9.16.1Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide |
| 10 | 5.9.2Centering and shuttering including strutting, etc. and removal of form for:Walls (anythickness) including attached pilasters, butteresses, plinth and string courses etc. (Combined quantity sub head and sub head 7= 117.88+476 ) |
| 11 | 5.9.19 Centering and shuttering including strutting, etc. and removal of form for:Weathershade, Chajjas, corbels etc., including edges |
| 12 | 5.22A.6Steel reinforcement for R.C.C work including straightening, cutting, bending, placingin position and binding all complete above plinth level.Thermo - MechanicallyTreated bars of grade Fe-500D or more |
| 13 | 6.47Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 150mm/230mm/300 mm thick with Grade- I AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). (Combined quantity sub head and sub head 6 = 107.397+34) |
| 14 | 50.6.3.2Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete |
| 15 | 50.6.1.8Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand etc complete (Combined quantity sub head 1 and sub head 7= 5.00+69.896) |
| 16 | 22.5Providing and laying water proofing treatment in sunken portion of WCs, bathroometc., by applying cement slurry mixed with water proofing cement compoundconsisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includespreparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 17 | 13.1.112 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) (Combined quantity sub head and sub head 6 = 2499.614+230.00) |
| 18 | 13.16.16 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand) |
| 19 | 13.22Extra for plastering exterior walls of height more than 10 m from ground level forevery additional height of 3 m or part thereof. |
| 20 | 13.28.312 mm thick plain cement mortar bands in cement mortar 1:4 ( 1 cement : 4 fine sand) :Raised Band (Combined quantity sub head and sub head 7 = 500.00+1920.0) |
| 21 | 5.30Add for plaster drip course / groove in plastered surface or moulding to R.C.C.projections. |
| 22 | 13.26Add for plaster drip course / groove in plastered surface or moulding to R.C.C.projections (Combined quantity sub head and sub head 5 = 10.00+764.8) |
| 23 | 13.85.3Applying priming coats with primer of approved brand and manufacture, having lowVOC ( Volatile Organic Compound) content.With water thinnable cement primer onwalls surface having VOC content less than 50 grams / litre |
| 24 | 13.45.1Finishing walls with textured exterior pint of required shade:New work (Two or morecoats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primerapplied @ 2.20 kg/ 10 sqm |
| 25 | 13.48A.1Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. (Combined quantity sub head 1 and sub head 7 = 1531.38 + 350) |
| 26 | 13.52.1Finishing with Epoxy paint (two or more coats) at all locations prepared and appliedas per manufacturers specifications including appropriate priming coat,preparation of surface, etc. complete.On steel work |
| 27 | 13.83.2Wall painting with premium acrylic emulsion paint of interior grade, having VOC(Volatile including applying additional coats wherever required to achieve even shade and colour.Two coats |
| 28 | 11.41A.2.2 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of sizeSize of Tile 600 x 1200 mm |
| 29 | 11.41A.3.1 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm |
| 30 | 11.46.2Providing and laying Vitrified tiles indifferent sizes (thickness to be specified bymanufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm |
| 31 | 11.48.2Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy groutmix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm |
| 32 | 11.48.4Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy groutmix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 1000x1000 mm |
| 33 | 8.2.2.2Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded andprepolished, machine cut for kitchen platforms, vanity counters, window sills, faciasand similar locations, of required size, approved shade, colour and texture laid over20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm |
| 34 | 8.3.2Providing edge moulding to 18 mm thick marble stone counters, vanities etc.,including machine polishing to edge to give high gloss finish etc. complete as perdesign approved by Engineer -in-Charge.Granite work |
| 35 | 5.18.3Providing precast cement concrete jali 1:2:4 ( 1 cement : 2 coarse sand : 4 gradedstone aggregate 6 mm nominal size) reinforced with 1.6 mm dia mild steel wire including centering and shuttering, roughening cleaning, fixing and finishing incement mortar 1:3 (1 cement : 3 fine sand ) etc. complete excluding plastering of the jambs, sills and soffits.25 mm thick |
| 36 | 10.28Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and makingcurvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 37 | 10.26.3Providing and fixing hand rail of approved size by welding etc. to steel ladder railing,balcony railing, staircase railing and similar works, including applying priming coatof approves steel primer.G.I. pipes |
| 38 | 9.48.2Providing and fixing M.S. Grills of required pattern in frames of windows etc. withM.S. flats, square or round bars etc. including priming coat with approved steelprimer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc |
| 39 | 21.18Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately) |
| 40 | OD176008/2026-2027Providing and fixing Stainless steel (304) patch fitting corner lock with cover for 1214mm thick frame less glass doors including all necessary accessories. Dorma orequivalent or higher make. All including the cost and conveyance of material andlabour charges etc, complete as per direction of Engineer -in-Charge. |
| 41 | OD176009/2026-2027Providing and fixing Stainless steel door handles for frameless glass doors includingall necessary accessories. 450mm long SS 304 door handles width/dia notless than 25mm. Dorma or higher equivalent make. All including the cost and conveyance of material and labour charges etc, complete as per direction of Engineer -in-Charge. |
| 42 | OD183656/2026-2027 Providing and fixing Half dome floor stop for frameless glass doors including allnecessary accessories. 45 mm dia half dome door stopper Dorma or higherequivalent make. All including the cost and conveyance of material and labourcharges etc, complete as per direction of Engineer -in-Charge. |
| 43 | 9.170.1Providing and fixing stainless steel fancy handle of approved make fixed with SSscrews etc. complete as per direction of Engineer-in-charge.200 mm |
| 44 | 9.113Providing and fixing bright finished 100 mm mortice lock with 6 levers without pairof handles of approved quality for aluminium door, with necessary screws etccomplete as per direction of Engineer- in- charge. |
| 45 | 9.100.1Providing and fixing aluminium handles, ISI marked, anodised (anodic coating notless than grade AC 10 as per IS : 1868) transparent or dyed to required colour orshade, with necessary screws etc. complete:125 mm |
| 46 | 9.101.1Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised(anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed torequired colour and shade, with necessary screws etc. complete.Single rubber stopper |
| 47 | 9.84Providing and fixing aluminium extruded section body tubular type universalhydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body,door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), withdouble speed adjustment with necessary accessories and screws etc. complete. |
| 48 | 9.97.3Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating notless than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:200x10 mm |
| 49 | 9.117.2Providing and fixing factory made uPVC door frame made of uPVC extrudedsections having an overall dimension as below (tolerance ±1 mm), with wallthickness 2.0mm (±0.2 mm), corners of the door frame to be jointed withgalvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-chargeExtruded section profile size 42x50 mm |
| 50 | 9.118.1Providing and fixing to existing door frames24 mm thick factory made PVC doorshutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of; section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness,fixed to the shutter styles by means of plastic/galvanised M.S. cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts andwashers, complete as per manufacturer's specification and direction ofEngineer-in-charge( For W.C. and bathroom door shutter). |
| 51 | 9.147D.2Providing and fixing factory made uPVC white colour sliding glazed window upto1.50 m in height dimension comprising of uPVC multi-chambered frame with in-builtroller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thickgalvanized mild steel section made from roll forming process of required length(shape & size according to uPVC profile), appropriate dimension of uPVC extrudedglazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy(white powder coated) touch locks with hook, zinc alloy body with single nylonrollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 +/- 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm). |
| 52 | 9.147C.2Providing and fixing factory made uPVC white colour casement/ Casement cumfixed glazed door comprising of uPVC multi-chambered frame, sash and mullion(where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thickgalvanized mild steel section made from roll forming process of required length(shape & size according to uPVC profile), uPVC extruded glazing beads ofappropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multipoint locking having transmission gear, cylinder with keeps and one side key,G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessarystainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusionwelded at all corners, mullion (if required) shall be also fusion welded includingdrilling of holes for fixing hardware's and drainage of water etc. After fixingframe the gap between frame and adjacent finished wall shall be filled withweather proof silicon sealent over backer rod of required size and of approvedquality, all complete as per approved drawing & direction of Engineer-in-Charge.(Single / double glass panes and silicon sealent shall be paid separately).Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Casement door withtop hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of(big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm allhaving wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing beadof appropriate dimension.(Area of door upto 2.50 sqm) |
| 53 | 50.9.10.1Providing and fixing 25 mm thick shutters for cup board etc. glazed shutters usingAnjili/jack wood wood including ISI marked nickel plated bright finished M.S. pianohinges with necessary screws. |
| 54 | 50.12.2.1Providing & fixing Poly carbonate corrugated sheet 0.8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling / self tapping screw of size (5.5x55 mm) with EPDM seal complete upto any pitch in horizontal/ vertical/ curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size shapes where ever required. |
| 55 | 10.16.1Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 56 | 10.5.1Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angleiron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces |
| 57 | OD131655/2026-2027Providing and fixing 3 mm thick UV-stabilized solid polycarbonate sheet of approved make and color shall be carried out over the existing or new framework. The sheets shall conform to relevant IS standards, have a density not less than 1.2 g/cm³, excellent impact resistance, and minimum light transmission of 80% for clear sheets. Each sheet shall have a co-extruded UV protective layer on the outer surface to resist weathering, yellowing, and degradation. The sheets shall be fixed with self-drilling galvanized screws with EPDM washers and appropriate aluminum or PVC profiles to ensure water-tightness. Side overlaps shall be not less than 50 mm and end overlaps shall be not less than 150 mm, sealed properly using neutral silicone sealant of approved quality. Cutting and drilling shall be done using recommended tools to prevent cracking or chipping of the sheets. All fixing shall be plumb, properly aligned, and executed in accordance with the manufacturer?s specifications and instructions including all cost of material and labour charge et complete as directed by Engineer-in-Charge. |
| 58 | OD131656/2026-2027Supply and fixing of 6 inch PVC square rain water gutter at required slope, includingall cost of clamps , other material and labour charges etc complete as directed byEngineer in charge. |
| 59 | 2.6.1Earth work in excavation by mechanical means (Hydraulic excavator)/manual meansover areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan)including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge.All kinds of soil |
| 60 | 2.7.1Earth work in excavation by mechanical means (Hydraulic excavator )/ manual meansover areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan)including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposedearth to be levelled and neatly dressed.Ordinary rock |
| 61 | 4.1.8Providing and laying in position cement concrete of specified grade excluding thecost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mmnominal size derived from natural sources) |
| 62 | 5.22.6Steel reinforcement for R.C.C work including straightening, cutting, bending, placingin position and binding all complete upto plinth levelThermo - Mechanically Treatedbars of grade Fe-500D or more(Combined quantity sub head and sub head 7 = 3447.60+ 4896.0) |
| 63 | 5.33.1.2Providing and laying in position ready mixed or site batched design mix cementconcrete for reinforced cement concrete work; using coarse aggregate and fineaggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 toaccelerate / retard setting of concrete, to improve durability and workability withoutimpairing strength; including pumping of concrete to site of laying, curing, carriagefor all leads; but excluding the cost of centering, shuttering, finishing andreinforcement as per direction of the engineer-in-charge; for the following grades ofconcrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cementAll work upto plinth levelConcrete of M30 grade with minimum cement content of350 kg /cum |
| 64 | 19.18.2Supplying and fixing C.I with out frame for manholes:500 mm diameter C.I.(medium duty) the weight of the cover to be not less than 58 kg |
| 65 | Plumbing and Sanitary Works |
| 66 | 18.8.3Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermalstability for hot & cold water supply, including all CPVC plain & brass threadedfittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing ofpipes& fittings, with one step CPVC solvent cement and the cost of cutting chasesand making good the same including testing of joints complete as per direction ofEngineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal dia pipes |
| 67 | 18.8.4Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermalstability for hot & cold water supply, including all CPVC plain & brass threadedfittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing ofpipes& fittings, with one step CPVC solvent cement and the cost of cutting chasesand making good the same including testing of joints complete as per direction ofEngineer-in-Charge. Concealed work, including cutting chases and making good thewall etc.32 mm nominal dia pipes |
| 68 | 18.7.4Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermalstability for hot & cold water supply, including all CPVC plain & brass threadedfittings including fixing the pipe with clamps at 1.00 m spacing. This includesjointing of pipes & fittings with one step CPVC solvent cement and testing of jointscomplete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32mm nominal dia pipes |
| 69 | 18.7.5Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermalstability for hot & cold water supply, including all CPVC plain & brass threadedfittings including fixing the pipe with clamps at 1.00 m spacing. This includesjointing of pipes & fittings with one step CPVC solvent cement and testing of jointscomplete as per direction of Engineer -in-Charge. Internal work - Exposed on wall 40 mm nominal dia pipes |
| 70 | 18.7.6Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermalstability for hot & cold water supply, including all CPVC plain & brass threadedfittings including fixing the pipe with clamps at 1.00 m spacing. This includesjointing of pipes & fittings with one step CPVC solvent cement and testing of jointscomplete as per direction of Engineer -in-Charge. Internal work - Exposed on wall 50 mm nominal dia pipes |
| 71 | 50.18.9.17.2Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 mspacing. This includes jointing of pipes with one step PVC solvent cement and testingof joints complete as per direction of Engineer-in-Charge 63 mm dia 4 Kgf/cm2External work - exposed on wall |
| 72 | 50.18.9.19.2Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 mspacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 m dia 4 Kgf/cm2 External work - Exposed on wall |
| 73 | 50.18.9.20.1Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63 mm dia Elbow |
| 74 | 50.18.9.20.2Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement -63 dia 45 degree Elbow |
| 75 | 50.18.9.20.3Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63 mm dia Door Elbow |
| 76 | 50.18.9.20.4Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63 mm dia Bend |
| 77 | 50.18.9.20.5Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipesincluding jointing with PVC solvent cement - 63x63x63 mm dia Tee |
| 78 | 50.18.9.20.6Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement -63x63x63 mm dia Door Tee |
| 79 | 50.18.9.20.7Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63 mm dia vent cowl |
| 80 | 50.18.9.20.9Providing and fixing PVC moulded fitting / accessories for Rigid PVC pipes,including jointing with PVC solvent cement-63 mm dia Socket /coupling |
| 81 | 50.18.9.22.1Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Elbow |
| 82 | 50.18.9.22.11Providing and fixing PVC moulded fittings/accessories for Rigid PVCpipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling |
| 83 | 50.18.9.22.2Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow |
| 84 | 50.18.9.22.3Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement-110 mm dia Door Elbow |
| 85 | 50.18.9.22.4Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement- 110 mm dia Bend |
| 86 | 50.18.9.22.5Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipesincluding jointing with PVC solvent cement 110x110x110 mm dia Tee |
| 87 | 50.18.9.22.6Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110x110x110 mm dia Door tee |
| 88 | 50.18.9.22.8Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes,including jointing with PVC solvent cement -110 mm dia Vent cowl |
| 89 | OD106680/2026-2027Providing and fixing 110 mm PVC multi inlet floor trap with 125mm stainless steelgratings, jointing with PVC solvent cement including cost and conveyance of allmaterial and labour charges. |
| 90 | OD106685/2026-2027Supplying and fixing CPVC ball valve of approved quality, 50mm nominal bore |
| 91 | OD106686/2026-2027Supplying and fixing CPVC ball valve of approved quality, 40mm nominal bore |
| 92 | OD106687/2026-2027Supplying and fixing CPVC ball valve of approved quality, 25mm nominal bore |
| 93 | OD106688/2026-2027Supplying and fixing CPVC ball valve of approved quality, 32mm nominal bore |
| 94 | 18.51.1Providing and fixing C.P. brass long body bib cock of approved quality conforming toIS standards and weighing not less than 690 gms.15 mm nominal bore |
| 95 | 18.52.1Providing and fixing C.P brass stop cock ( concealed) of standard design and ofapproved make conforming to IS: 893115 mm nominal bore |
| 96 | 18.53.1Providing and fixing C.P. brass angle valve for basin mixer and geyser points ofapproved quality conforming to IS: 893115 mm nominal bore |
| 97 | 50.17.1.5Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make )including cost of materials and labour charges etc complete as per the direction of siteEngineer-in-charge. |
| 98 | 17.1.1Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mmSand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, includingflush pipe, manually controlled device (handle lever) conforming to IS : 7231, withall fittings and fixtures complete, including cutting and making good the walls andfloors wherever require:White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests |
| 99 | 17.81Providing and fixing floor mounted, white vitreous china single piece, double trapssyphonic water closet of approved brand/make, shape, size and pattern includingintegrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 100 | OD106845/2026-2027Providing and fixing C.P. brass shower arm and shower rose (flat rain) with 15 or 20mm inlet: 150 mm diameter rain shower rose and 450mm long shower arm superiorquality as instructed by Engineer in charge |
| 101 | OD106859/2026-2027Providing and fixing White vitreous china clay half stall urinal flat back 580x380x350 mm angle back 450x375x350 with waste fittings as per IS: 2556, 15mm nominal bore C.P brass urinal push cock of approved quality, standard flush pipe, spreaders with unions and clamps (all in C.P. brass) as per IS : 2556, and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required: All including the cost and conveyance of material and labour charges etc. complete |
| 102 | OD106865/2026-2027Providing and fixing mirror of superior glass (approved quality) of required shape andsize complete with C.P. brass screws and washers complete. |
| 103 | OD106866/2026-2027Supplying and fixing CP soap dish 100mm or nearest heavy stainless steel or basicbrass-bodied wall mounts available size and shape including cost of materials andlabour charges etc complete as per the direction of site Engineer-in-charge |
| 104 | 17.73.2Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleatswith CP brass screws with concealed fitting arrangement of approved quality andcolour600 mm long towel rail with total length of 645 mm, width 78 mm andeffective height of 88 mm, weighting not less than 190 gms |
| 105 | 51.19.ST4Supplying and installing ready made PVC Septic tank including the cost of carriage,trenching, placing at the level below ground level as specified as per the direction ofengineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparationof bed shall be paid separately) 35 to 50 flush capacity |
| 106 | 18.33.1Constructing masonry chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement:4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5 |
| 107 | 18.34.1Constructing masonry chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 108 | 18.35.1Constructing masonry chamber 120x120x100 cm inside, in brick work in cementmortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I surface box 100 mmtop diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lidand RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 grades stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 109 | 18.48Providing and placing on terrace (at all floor levels) polyethylene water storage tank:ISI 12701 marked, with cover and suitable locking arrangement and makingnecessary holes for inlet, outlet and overflow pipes but without fittings and the basesupport for tank |
| 110 | 17.7.8Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow including operated levers |
| 111 | 19.33Constructing soak pit 1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 112 | Electrical Works |
| 113 | 1.10.3Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mmFRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C |
| 114 | 1.11Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copperconductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. |
| 115 | 1.17.12Supplying and drawing following sizes of FRLS PVC insulated copper conductor,single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x2.5 sq. mm |
| 116 | 1.17.21Supplying and drawing following sizes of FRLS PVC insulated copper conductor,single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm |
| 117 | 1.17.3Supplying and drawing following sizes of FRLS PVC insulated copper conductor,single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm |
| 118 | 1.18.2Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealedcopper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair |
| 119 | 1.19Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copperconductor PE insulated, shielded with fine tinned copper braid and protected withPVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 120 | 1.21.1Supplying and fixing of following sizes of medium class PVC conduit along withaccessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm |
| 121 | 1.21.2Supplying and fixing of following sizes of medium class PVC conduit along withaccessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 122 | 1.24.1Supplying and fixing following modular switch/ socket on the existing modular plate; switch box including connections but excluding modular plate etc. asrequired.5/6 amps switch |
| 123 | 1.53.1Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable |
| 124 | 1.24.3Supplying and fixing following modular switch/ socket on the existing modular plate ; switch box including connections but excluding modular plate etc. as required.15/16 amp switch |
| 125 | 1.24.4Supplying and fixing following modular switch/ socket on the existing modular plate; switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet |
| 126 | 1.24.6Supplying and fixing following modular switch/ socket on the existing modular plate& switch box including connections but excluding modular plate etc. asrequired.Telephone socket outlet |
| 127 | OD129996/2026-2027Supply and Fixing the following modular switches; accessories in the existingfront plates and giving necessary connections as required (RoHS compliant )20A DPswitch with indicator |
| 128 | 1.24.7Supplying and fixing following modular switch/ socket on the existing modular plate; switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet |
| 129 | 1.24.8Supplying and fixing following modular switch/ socket on the existing modular plate; switch box including connections but excluding modular plate etc. as required.Bell push |
| 130 | 1.25Supplying and fixing two module stepped type electronic fan regulator on the existingmodular plate switch box including connections but excluding modular plate etc. asrequired. |
| 131 | 1.26Supplying and fixing modular blanking plate on the existing modular plate &switch box excluding modular plate as required. |
| 132 | 1.27.1Supplying and fixing following size/ modules, GI box alongwith modular base ; cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm) |
| 133 | 1.31Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socketoutlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). |
| 134 | 1.33Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ woodenblock including connection etc as required. |
| 135 | 1.41Installation, testing and commissioning of pre - wired, fluorescent fitting/ compactfluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copperconductor, single core cable and earthing etc. as required |
| 136 | 90.4.3Conveyance installation testing and commissioning ceiling fan of all sizes usingstandard accessories excluding resistance type regulator wiring the down rod with16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or extending the original wiring etc. as required. |
| 137 | 90.5.1.3Supply and fixing the following types of superior quality 250V A.C call bell on existing M.S. box and giving connections with required length of 3 core, 16 / 0.20mm 650/1100V grade PVC insulated and PVC sheathed round copper conductor flex wire conforming to relevant ISS or with the extended original wiring, earthing the MS box and making good the surface as required.Ding dong bell |
| 138 | 90.6.5.1Supply and drawing the following sizes of multi-core PVC insulated & FRLSPVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.2 core 0.50 sq mm |
| 139 | 1.24.5Supplying and fixing following modular switch/ socket on the existing modular plate& switch box including connections but excluding modular plate etc. asrequired.6 pin 15/16 amp socket outlet |
| 140 | 1.47Supplying and fixing extra down rod of 10 cm length G.I. pipe, 15 mm dia, heavygauge including painting etc. as required. (Note: More than 5 cm length shall berounded to the nearest 10 cm and 5 cm or less shall be ignored |
| 141 | 1.49Numbering of ceiling fan / exhaust fan/ fluorescent fittings as required. |
| 142 | 1.50.1Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep |
| 143 | 1.51Installation of exhaust fan in the existing opening, including making good thedamage, connection, testing, commissioning etc. as required |
| 144 | 1.58Supplying and fixing PVC batten/ angle holder including connection etc. as required |
| 145 | 1.27.3Supplying and fixing following size/ modules, GI box alongwith modular base; cover plate for modular switches in recess etc as required.4 Module (125mmX75mm |
| 146 | 2.10.1Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, \\"\\"C\\"\\" curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required.Single pole |
| 147 | 2.10.2Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, \\"\\"C\\"\\" curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required.Single pole and netural |
| 148 | 2.10.4Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, \\"\\"C\\"\\" curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required.Triple pole |
| 149 | 2.11Supplying and fixing single pole blanking plate in the existing MCB DB completeetc. as required |
| 150 | 2.12.1Supplying and fixing following rating, double pole, 240 volts, isolator in the existingMCB DB complete with connections, testing and commissioning etc. as required.40amps |
| 151 | 2.13.1Supplying and fixing following rating, four pole, 415 volts, isolator in the existingMCB DB complete with connections, testing and commissioning etc. as required.40 amps |
| 152 | 2.13.2Supplying and fixing following rating, four pole, 415 volts, isolator in the existingMCB DB complete with connections, testing and commissioning etc. as required.63amps |
| 153 | 2.14.1Supplying and fixing following rating, double pole, (single phase and neutral),240volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milliamperes in the existing MCB DB complete with connections, testing andcommissioning etc. as required. 25 amps |
| 154 | 2.15.2Supplying and fixing following rating, four pole, (three phase and neutral), 415volts, residual current circuit breaker (RCCB), having a sensitivity current 30milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps |
| 155 | 2.15.3Supplying and fixing following rating, four pole, (three phase and neutral), 415volts, residual current circuit breaker (RCCB), having a sensitivity current 30milli Amperes in the existing MCB DB complete with connections, testing andcommissioning etc. as required. 63 amps |
| 156 | 2.18Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2pole and earth,metal enclosed plug top along with 20 amps curve, SP,MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 157 | 2.21Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mildsteel, at least 2 mm thick, and vitreous enameled white on both sides, and withinscription in single red colour on front side as required |
| 158 | 2.3.3Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)12 way, Double door |
| 159 | 2.4.1Supplying and fixing following way, horizontal type three pole and neutral, sheetsteel, MCB distribution board, 415 volts, on surface / recess, complete with tinnedcopper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 Way (4+12) Double door |
| 160 | 2.5.1Supplying and fixing of following ways surface/ recess mounting, vertical type, 415volts, TPN MCB distribution board of sheet steel, dust protected, duly powderpainted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 WAY(4+12), DOUBLE DOOR |
| 161 | 5.14Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.. |
| 162 | OD130001/2026-2027Documents and; Approval : Preparation of necessary forms, documents drawingsetc. with necessary certifications & test reports and procuring approval andenergization certificate from Kerala state Electricity Board / Electrical Inspectorateincluding all miscellaneous expenses and all related expenses & formalities shall be met by contractor but excluding statutory charges, cash deposit etc. |
| 163 | OD130101/2026-2027S/F CAT 6 RJ 45 Computer Jack, Modular on existing box & plate: Supplyand fixing modular type CAT 6 RJ 45 Computer Jack on existing modular box &;cover plate and giving connections etc as required |
| 164 | OD130117/2026-2027Supply and drawing 3 C x 6 sq.mm armoured copper cable. Supplying and layingPVC Insulated and sheathed 3 C x 6 sq.mm armoured copper cable with annealedplain electrolytic copper conductor as per IS 8130/1934 insulated and sheathedwith electrical grade PVC compound as per IS 5831/1984 generally conforming to IS 694/1990, and laying direct in ground including excavation and refilling the trench etcas required, but excluding sand cushioning and protective covering |
| 165 | OD130120/2026-2027Supply and doing termination of 3C x 2.5 sq.mm armoured Cu cable in suitable IP65/66 Junction box. |
| 166 | OD130121/2026-2027Supply of 9 W retrofit LED: Supply & providing 9 W retrofit LED for the anglebatten holder, etc. as required. |
| 167 | OD130127/2026-2027S/F of 400mm Wall Fan : Supply and fixing of 400 mm sweep wall fan with threepositions and pulling cords and giving connection etc. as required |
| 168 | OD130133/2026-2027Supply of 305mm Exhaust Fan : Supply of 305 mm sweep light duty exhaust fan inmetal frame suitable for operation on 220/ 240V, 50 Hz, single phase AC supply etc. as required |
| 169 | 5.5Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required |
| 170 | 90.15.4.1Supply Conveyance, installation, testing and commissioning of 20W LED street lightoutput greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip makeCree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surgeprotection up to 8 KV,and Aluminium pressure die-cast Powder coated housing,acrylic cover complete with THD Less than10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer) |
| 171 | OD130136/2026-2027Supply of 20W LED batten/ tube light fittings : Supply and providing 20W Surfacemounting type LED lenier batten/ tube light fittings with output of 2000 lumen, withwhite acrylic cover etc. as required. |
| 172 | 1OD130137/2026-2027Supply of 10±2W surface mounted LED mirror light fixture, 4000K-5700K colourtemperature, minimum 100 lumen/Watt, working on 240V AC etc as required |
| 173 | OD130138/2026-2027Supply, installation, testing, and commissioning of a 8W per meter LED cove lightfixture with a length of 5m, 3000K color temperature, including suitable capacityLED driver with all necessary accessories, connections, etc as required |
| 174 | OD130169/2026-2027Supply, installation, testing, and commissioning of a 8W per meter LED Strip lightfixture with a length of 5m, 3000K color temperature, including suitable capacityLED driver with all necessary accessories, connections, etc as required. |
| 175 | 90.12.7.30Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armouredaluminium power cable, 1.1 KV grade of the following sizes using clamps notedalong with the cables, spacing of clamps not exceeding 60cms, making good thedamages , colour washing etc. as required.3.5 core 70 sq mm |
| 176 | 90.12.7.41Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp |
| 177 | 9.1.23Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm) |
| 178 | 9.1.33Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm) |
| 179 | OD128964/2026-2027SITC of 3 HP submersible pumpset: Supply, installation, testing and commissioning of 3 HP, 32 Stage, S.S. body, Water Filled Borewell Submersible Pump Set, suitable for operation on 240V, 50Hz Three phase AC supply along with SITC of control panel having protection switch gears, digital meter, starter etc suitable for the operation of the pump etc including all accessories for borewell and giving connection etc.as required |
| 180 | OD130201/2026-2027Supply, installation, testing and commissioning of 9W LED gate top light fixture (IP65), having aluminium die-cast housing, 4000K colour temperature, graphite greypowder coating finish, duly wired up for use on 240 V AC supply, suitable foroutdoor applications including all connections etc. as required. |
| 181 | Fire Fighting Works |
| 182 | 18.1.5a)Supplying,installation,testing and commissioning of Electric driven Main FirePump suitable for Automatic operation and consisting of following, complete in allrespect , as required :b) Horizontal type, Multi stage ,centrifugal, split casing Pump of Cast Iron body andbronze impeller with stainless steel shaft ,mechanical seal conforming to IS 1520.C) Suitable HP Squirrel Cage Induction Motor, TEFC, Synchronous speed 1500rpmsuitable for operation on 415 V 3 phase 50 HZ AC supply with IP55 Protection forenclosure ,horizontal foot mounted type with class F insulation, conforming to IS 325.d) M.S Fabricated common base plate coupling, coupling guard ,foundation bolts etc as required.e) Suitable cement concrete foundation duly plastered with Anti vibration pads2280 lpm at 70 m head |
| 183 | 18.10.2Supplying and fixing single headed external yard hydrant valve with one no: 63 mmdia instantaneous FM Gun metal or stainless steel coupling and cast iron wheel, ISImarked ISI marked conforming to IS 5290(Type A) with blank Gun metal orStainless steel cap and chain as required:Single headed stainless steel |
| 184 | 18.11.4Supplying, fixing, testing and commissioning of Butterfly Valve of PN 1.6 ratingwith bronze or gun metal seat duly ISI marked complete with nuts, bolts ,washers,gaskets conforming to IS 13095 of following sizes as required:80 mm dia |
| 185 | 18.11.5Supplying, fixing, testing and commissioning of Butterfly Valve of PN 1.6 ratingwith bronze or gun metal seat duly ISI marked complete with nuts, bolts ,washers,gaskets conforming to IS 13095 of following sizes as required:100 mm dia |
| 186 | 18.11.6Supplying, fixing, testing and commissioning of Butterfly Valve of PN 1.6 ratingwith bronze or gun metal seat duly ISI marked complete with nuts, bolts ,washers,gaskets conforming to IS 13095 of following sizes as required:150 mm dia |
| 187 | 18.11.7Supplying, fixing, testing and commissioning of Butterfly Valve of PN 1.6 ratingwith bronze or gun metal seat duly ISI marked complete with nuts, bolts ,washers,gaskets conforming to IS 13095 of following sizes as required:200 mm dia |
| 188 | 18.2.5a)Supplying,installation,testing and commissioning of Diesel Engine driven MainFire Pump suitable for Automatic operation and consisting of following, complete inall respect , as required :(Diesel Driven Pump)b) Horizontal type, Multi stage ,centrifugal, split Pump of Cast Iron body and bronzeimpeller with stainless steel shaft ,mechanical seal conforming to IS 1520.C) Suitable HP ,1500rpm,water cooled with radiator,diesel engine conforming torelevant IS standard complete with auto starting mechanism 12/24 V Electric starting equipment,diesel tank, exhaust pipe extended upto 10m outside pump house duly insulated with 50 mm thick glass wool with 1 mm thick Al sheet cladding residential silencer, instruments and protection as per standard specifications, stop solenoid for Auto stop in the event of fault with audio indications, painted with post office red colour etc as required.d) M.S Fabricated common base plate coupling, coupling guard ,foundation bolts etc as required.e) Suitable cement concrete foundation duly plastered with Anti vibration pads2280lpm at 70 m head |
| 189 | 18.20supplying and fixing air vessel made of 250 mm dia 8 mm thick MS sheet , 1200 mm in height with Air release valve on top and flanged connection to riser , drainarrangement with 25 mm dia Gun metal wheel valve with required accessories ,pressure guage and painting with synthetic enamel paint of approved shade asrequired. |
| 190 | 18.22Providing and fixing of pressure switch in MS pipeline including connection etc asrequired: |
| 191 | 18.23.1Providing and fixing of flow switch in MS pipe including connection etc asrequired:100 mm dia |
| 192 | 18.24.3Providing, fixing, testing & commissioning of installation control valve of cast ironbody, brass/bronze working parts comprising of water motor alarm, bronze seatclapper, clapper arm and hydraulically driven mechanical gong bell to soundcontinuous alarm when the wet riser/sprinkler system activates,pressure gauges,emergency releases, strainer, pressure switch, cock valve complete with drain valveand bypass, test control box, ball valves, MS pipeof required size, flanges, orifice |
| 193 | 18.3.6a)Supplying, installation, testing and commissioning of Electric driven PressurisationPump suitable for Automatic operation and consisting of following, complete in allrespect , as required :(Jockey Pump)b) Horizontal type, Multi stage ,centrifugal, split casing Pump of Cast Iron body andbronze impeller with stainless steel shaft ,mechanical seal conforming to IS 1520.C) Suitable HP Squirrel Cage Induction Motor, TEFC type suitable for operation on415 V 3 phase 50 HZ AC supply with IP55 Protection for enclosure ,horizontal footmounted type with class F insulation, conforming to IS 325.d)M.S Fabricated common base plate coupling, coupling guard ,foundation bolts etcas required. e) Suitable cement concrete foundation duly plastered with Anti vibrationpads300lpm at 56m Head |
| 194 | 18.5.1Fabrication, supply, installation, testing and commissioning of Electrical Control Panel of cubicle construction Floor mounted type fabricated out of 2 mm thick CRCA sheet compartmentalised with hinged lockable doors, dust vermin proof, powder coated of approved shade after 7 tank treatment process cable alleying interconnection with suitable size copper conductor cable or solid copper strip having switchgearsand accessories, mopuntigs and internal wiring, earth terminals, numbering etc., complete in all respects suitable for main fire pump , pressurisationpump and diesel pump set complete as per CPWD specification with followingincoming and outgoings suitable for operation of 415 V, 3 phase, 50 Hz, AC supplywith enclosure protection class IP 42 as required: INCOMING : 250A, 50kA 4PMCCB ,Ics=100% Icu rating Digital Voltmeter 0-500V with selector switch DigitalAmmeter 0-250A with selector switch and CTs etc. LED Type RYB phase indicatingLamps ,ON/OFF, Trip indicating lamps set of Cu Bus Bar 300A .OUT GOING :(Note : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating lamps)MAIN FIRE PUMP: 125 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 60 HP pump with overload protection, current sensing type single phase preventor complete with all accessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation.JOCKEY PUMP : 63 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation.DIESEL ENGINE CONTROL: Control for diesel engine comprising - Automatic/Manual selctor switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0-20 A DC Ammeter All standard relays and accessories for automatic operation of diesel engine System ControllerDesigning, Supply, Installation, Testing and commissioning of system controller tocontrol operation of main electric fire pump, diesel pump, Pressurization pump,Terrace pump in sequence as per specification consisting of relays, timers. Sensors,annunciation window for fault indication, complete as per specification |
| 195 | 18.6.2Providing, laying, testing and commissioning of C class heavy duty M S Pipeconforming to IS 1239/3589 i/c fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., in ground including welding ,excavation and providing cement concrete blocks as supports, Anti corrosive treatment with coal tar ,Asphalt type as per IS 10221, refiiling the trench etc., of following sizes150 mm dia |
| 196 | 18.7.1Providing, laying, testing and commissioning of C class heavy duty M S Pipe conforming to IS 3589,IS 1239 i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required:25 mm dia |
| 197 | 18.7.2Providing, laying, testing and commissioning of C class heavy duty M S Pipe conforming to IS 3589,IS 1239 i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required:32 mm dia |
| 198 | 18.7.4Providing, laying, testing and commissioning of C class heavy duty M S Pipe conforming to IS 3589,IS 1239 i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required:50 mm dia |
| 199 | 18.7.5Providing, laying, testing and commissioning of C class heavy duty M S Pipe conforming to IS 3589,IS 1239 i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required:65mm dia |
| 200 | 18.7.6Providing, laying, testing and commissioning of C class heavy duty M S Pipe conforming to IS 3589,IS 1239 i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamelpaints of required shades complete as required:80mm dia |
| 201 | 18.7.7Providing, laying, testing and commissioning of C class heavy duty M S Pipe conforming to IS 3589,IS 1239 i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required:100mm dia |
| 202 | 18.7.8Providing, laying, testing and commissioning of C class heavy duty M S Pipeconforming to IS 3589,IS 1239 i/c welding ,fittings, like elbows, tees, flanges,tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required:150mm dia |
| 203 | 18.7.9Providing, laying, testing and commissioning of C class heavy duty M S Pipeconforming to IS 3589,IS 1239 i/c welding ,fittings, like elbows, tees, flanges,tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitableclamp or support frame and painting with two or more coats of synthetic enamelpaints of required shades complete as required:200mm dia(Wall thickness 6.3mm) |
| 204 | 18.9.2Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal or stainless steel coupling of 63mm dia with cast iron wheel ISI markedconforming to IS 5290(Type A) with blank Gun metal or Stainless steel cap and chainas required:Single headed stainless steel |
| 205 | 16.8Providing and fixing in position the industrial type pressure gauges with gun metal /brass valves complete as required |
| 206 | 18.17.1Supplying and fixing first-aid Hose Reel with MS construction spray painted in postoffice red, conforming to IS 884 complete with the following as required.a) 20 mm nominal Internal dia water hose thermoplastic(Textile reinforced) type-2 as per IS:12585b) 20 mm nominal internal dia gun metal globe valve &nozzlec) Drum and brackets for fixing the equipments on wall.d) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe andsocket. 30 m |
| 207 | 18.18.2Supplying and fixing 63 mm dia gun etal short metal branch pipe ith 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for Instantaneous connection to Interconnect hose pipe coupling as required:Stainless steel (Grade 304) |
| 208 | 17.2.1.2INTELLIGENT FIRE ALARM SYSTEMTwo Loop Panel |
| 209 | 17.2.11INTELLIGENT FIRE ALARM SYSTEMSupplying, installation, testing &commissioning of addressable phone control module complete as required |
| 210 | 17.2.14INTELLIGENT FIRE ALARM SYSTEMSupplying, installation, testing &commissioning of addressable manual call point complete as required. |
| 211 | 17.2.17INTELLIGENT FIRE ALARM SYSTEMSupplying, installation, testing &commissioning of fire fighter telephone handset complete as required |
| 212 | 17.5.2CABLING & WIRINGSupplying & laying of 2x1.5 sq mm fire alarmarmoured cable, 600/1000V rated with annealed copper conductor having XLPEinsulation, steel wire armouring & FRLS outer sheath complete as required |
| 213 | 18.3.2a)Supplying, installation, testing and commissioning of Electric driven PressurisationPump suitable for Automatic operation and consisting of following, complete in allrespect , as required :(Jockey Pump)b) Horizontal type, Multi stage ,centrifugal, split casing Pump of Cast Iron body andbronze impeller with stainless steel shaft ,mechanical seal conforming to IS 1520.C) Suitable HP Squirrel Cage Induction Motor, TEFC type suitable for operation on415 V 3 phase 50 HZ AC supply with IP55 Protection for enclosure ,horizontal footmounted type with class F insulation, conforming to IS 325.d)M.S Fabricated common base plate coupling, coupling guard ,foundation bolts etc as required.e) Suitable cement concrete foundation duly plastered with Anti vibration pads180lpm at 70m Head |
| 214 | Interior Design and Panelling Work |
| 215 | 21.1.1.3Providing and fixing aluminium work for doors, windows, ventilators and partitionswith extruded built up standard tubular sections/ appropriate Z sections and othersections of approved make conforming to IS : 733 and IS: 1285, fixing with dashfasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPolyester powder coated aluminium ( minimum thickness of polyester powder coating 50 micron ) |
| 216 | 21.1.2.3For shutters of doors, windows & ventilators including providing and fixinghinges / pivots and making provision for fixing of fittings wherever requiredincluding the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paidfor separately)Polyester powder coated aluminium (minimum thickness of polyesterpowder coating 50 micorn) |
| 217 | 21.2.2Providing and fixing 12 mm thick prelaminated particle board flat pressed three layeror graded wood particle board conforming to IS : 12823 Grade I Type II, in panellingfixed in aluminum doors, windows shutters and partition frames with C.P. brass /stainless steel screws etc. complete as per architectural drawings and directions ofEngineer - in- Charge.Pre- laminated particle board with decorative lamination onboth sides |
| 218 | 21.3.1Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 219 | 25.1Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approvedby the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).The weight of aluminum extruded section shall be taken for purpose of payment(Combined quantity sub head 5 and sub head 6 = 100+585.45) |
| 220 | 12.45.3Providing and fixing false ceiling at all height including providing and fixing of framework made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board |
| 221 | 9.133.1.1Providing and fixing, in position concealed G.I. section for wall paneling using boardof required thickness fixed on the 'W' profile (0.55 mm thick) having a knurled webof 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610mm C/C in perimeter channel having one flange of 20 mm and another flange of 30mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the 'W' profile with 25 mmcountersunk ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish. Tapered edge calcium silicate board made with calcareous & siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with compressive strength 225 kg/sqcm, Bending strength 100 kg/ sqcm.10 mm Thick |
| 222 | OD131647/2026-2027Finishing walls with Special texture paint rough finish Luxurious Polyurethane Interior & Exterior Texture Paint - Decorative wall finish washable paint of required shade: New work and finishing with Protective Coat over the finished surface (applied @ 1 ltr/ 1 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm (Combined quantity sub head 5 and sub head 6 = 124.5 + 533.532) |
| 223 | OD131650/2026-2027WPC Slat Wall Panels, Accent Slat Wood Slats for Wall and Ceilings, AcousticPanels for Interior Wall Modern Décor |
| 224 | OD132581/2026-2027Providing and fixing, in position concealed G.I. section for wall paneling using 18 mm Multiwood (0.7g/cc) fixed on the 'W' profile (0.55 mm thick) havinga knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm,placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. 18 mm Multiwood shall be fixed to the 'W' profile with suitable countersunk self-drilling/self-tapping screws of approved make and appropriate length and gauge, @ 200 mm c/c., ensuring firm and flush fixing without damage to the plywood, all complete as per the drawing & directions of engineer-in-charge, the joints of the plywood boards shall be suitably joined using jointing compound and sanded smooth, including treatment of screw heads, to provide a seamless and uniform uniform surface ready to receive the specified final finish, all complete as specified. |
| 225 | OD174955/2026-2027Providing fixing wood wool filling in between wall paneling works for sound proofeffect, supply pack fill, fix and finish all complete as per direction of engineer incharge |
| 226 | OD132996/2026-2027Providing 1 mm thick decorative mica lamination over the finished panelling worksincluding mica and adhesives fixing cleaning finishing all complete as specified |
| 227 | OD174978/2026-2027Providing and fixing, in position concealed G.I. section for wall paneling using 18mm Multiwood(0.7 g/cc) fixed on the 'W' profile (0.55 mm thick) havinga knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm,placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. 18 mm multiwood panel shall be fixed to the 'W' profile with suitable countersunk self-drilling/self-tapping screws of approved make and appropriate length and gauge, @ 200 mm c/c., ensuring firm and flush fixing without damage to the plywood, all complete as per the drawing & directions of engineer-in-charge, the joints of the multiwood boards shall be suitably filled and treated with approved wood filler/ jointing compound and sanded smooth, including treatment of screw heads, to provide a seamless and uniform uniform surface ready to receive the specified final finish, above which surface finished with 1 mm thick decorative mica laminate all inclusive complete as specified. |
| 228 | OD132598/2026-2027Providing and fixing, in position concealed G.I. section for wall paneling using 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710, (including mica lamination) fixed on the profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm andanother flange of 30 mm with thickness of 0.55 mm and web of length 27 mm.Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610mm C/C with fully threaded self-tapping dry wall screws. 19mm thick both sidebalancing lamination factory pressed BWP grade marine ply shall be fixed to the'W' profile with suitable countersunk self-drilling/self-tapping screws ofapproved make and appropriate length and gauge, @ 200 mm c/c., ensuring firm and flush fixing without damage to the plywood, all complete as per the drawing directions of engineer-in-charge, the joints of the plywood boards shall be suitablyfilled and treated with approved wood filler/ jointing compound and sanded smooth,including treatment of screw heads, to provide a seamless and uniform uniformsurface ready to receive the specified final finish, above which surface finished with 1 mm thick decorative mica laminate all inclusive complete as specified |
| 229 | OD133030/2026-2027Providing and fixing, in position concealed G.I. section for wall paneling using 12mm thick marine plywood conforming to IS: 710, fixed on the 'W' profile(0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm eachwith lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. 12 mm thick marine plywood shall be fixed to the 'W' profile with suitable countersunk selfdrilling/ self-tapping screws of approved make and appropriate length and gauge, @ 200 mm c/c., ensuring firm and flush fixing without damage to the plywood, all complete as per the drawing & directions of engineer-in-charge, the joints of the plywood boards shall be suitably filled and treated with approved wood filler/ jointing compound and sanded smooth, including treatment of screw heads, to provide a seamless and uniform uniform surface ready to receive the specified final finish, above which surface finished with 1 mm thick decorative mica laminate all inclusive complete as specified. |
| 230 | OD132968/2026-2027 Providing and fixing, wall paneling using 18 mm (0.7spg) Multiwood panelling fixedon wall/prepared surface ensuring firm and flush fixing without damage to themultiwood, all complete as per the drawing & directions of engineer-in-charge,the joints of the boards shall be suitably filled and treated with approved wood filler/jointing compound and sanded smooth, including treatment of screw heads if any, toprovide a seamless and uniform uniform surface ready to receive the specified finalfinish, above which surface finished with 1 mm thick decorative mica laminate allinclusive and complete as specified |
| 231 | OD132684/2026-2027ZEBRA Blind for Windows Dual Layer Zebra Roller Shades Light Filtering SheerWindow Treatments Privacy Light Control for day and night light weight fabric toallow maximum light diffusion. Excellent UV protection, insulation and energysavings. Fabric treated to resist stains and minimize dust built up supply andinstallation and finishing complete |
| 232 | OD133018/2026-2027Providing and fixing wall pannelling using 19mm thick both side balancinglamination factory pressed BWP grade marine ply as per IS 710, fixed on walls/prepared surface ensuring firm and flush fixing without damage to the plywood, allcomplete as per the drawing & directions of engineer-in-charge, the joints of the boards shall be suitably treated with approved jointing compound and sanded smooth, including treatment of screw heads, to provide a seamless and uniform uniform surface ready to receive the specified final finish, above which surface finished with 1 mm thick decorative mica laminate all inclusive and complete as specified |
| 233 | OD132656/2026-2027Supply Installation Testing & Commissioning of 2 Ton inverter Split AirConditioner (AC) of reputed brands such as LG/Blue Star/Voltas/ equivalent orhigher available brand with 3 Star or higher rating latest Model including outdoor and indoor unit on the angle iron frame, fixing of standard length copper refrigerant pipes, making thermal insulation with ready made poly foam tube (thickness not less than 5mm) i/c leak testing top up of gas giving electrical connections, testing and commissioning etc with all necessary accessories, connectors, mountingarrangements, stabilizer etc complete |
| 234 | Exterior Design and Finishing Work |
| 235 | 7.38.1.1Stone tile work for wall lining upto 10 m height with special adhesive over 12mmthick bed of cement mortar 1:3 (1 cement :3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade.8 mm thick (mirror polished and machine cut edge)Granite stone of any colour andshade |
| 236 | 8.15Providing and fixing stainless steel cramps of required size and shape for anchoringstone wall lining to the backing or securing adjacent stones in stone wall lining incement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chasesin stone and holes in walls wherever required |
| 237 | 8.32Designing, fabricating, testing, installing and fixing in position Curtain Wall withAluminium Composite Panel Cladding, with open grooves for linear as well ascurvilinear portions of the building , for all heights and all levels etc. including:(a) Structural analysis & design and preparation of shop drawings for pressureequalisation or rain screen principle as required, proper drainage of water to make itwatertight including checking of all the structural and functional design.(b) Providing,fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grademineral core sandwiched between two Aluminium sheets (each 0.5mm thick). Thealuminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. |
| 238 | 25.2Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well ascurvilinear portions of the building for all heights and all levels, including: a)Structural analysis & design and preparation of shop drawings for the specifieddesign loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of |
| 239 | 8.16Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacentstones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases. |
| 240 | 8.19Extra for stone work for wall lining on exterior walls of height more than 10 m fromground level for every additional height of 3m or part thereof |
| 241 | OD131645/2026-2027Providing and fixing Terracotta clay jali 75 mm thick throughout in cement mortar1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1White cement : 2 stone dust) with an admixture of pigment, matching the shade. Allincluding the cost and conveyance of material and labour charges etc complete. |
| 242 | OD131646/2026-2027Supplying and installation of PVC Louver panels as per standard sizes fixed withrubber based adhesive in both vertical and horizontal surfaces. PVC louver panels 12mm thick. |
| 243 | 25.4Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 - point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. |
| 244 | External Works - Landscapping, Compound wall, Gate ,Vehicle shelter, Drainage, Rainwater harvesting etc. |
| 245 | 16.91.2Providing and laying factory made chamfered edge Cement Concrete paver blocksin footpath, parks, lawns, drive ways or light traffic parking etc, of required strength,thickness & size/ shape, made by table vibratory method using PU mould, laid inrequired colour & pattern over 50mm thick compacted bed of sand, compacting andproper embedding/laying of inter locking paver blocks into the sand bedding layerthrough vibratory compaction by using plate vibrator, filling the joints with sand andcutting of paver blocks as per required size and pattern, finishing and sweepingextra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C.paver block of M-30 grade with approved color design and pattern. |
| 246 | 7.1.1Random rubble masonry with hard stone in foundation and plinth including levellingup with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 247 | OD129929/2026-2027Providing and laying ready-made machine-cut slabs natural stone - Bangalore stone of size 600mm x 600mm (2x2 ft) - 50mm thick for flooring or paving. The slabs are to be laid evenly to proper line, level, and slope over a prepared cushion bed of 50mm thick compacted baby metal (6mm to 12mm graded stone aggregate). The work includes maintaining uniform gaps, pointing and flushing the joints with cement grout / cement mortar (1:3), curing, and including the cost and conveyance of all materials, labour, lead, lift, and all incidental charges, complete as per standard specifications and the direction of the Engineer-in-charge |
| 248 | 13.1.212 mm cement plaster of mix:1:6 (1 cement : 6 fine sand). |
| 249 | 50.10.1Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.)trusses etc., including cutting, hoisting,fixing in position and applying a priming coatof approved steel primer, including welding and bolted with special shaped washersetc. complete |
| 250 | 50.10.2Steel work for purlin/single section with G I pipes including cutting, hoisting, fixingin position and applying a priming coat of approved steel primer, including weldingand bolted with special shaped washers etc. complete |
| 251 | 13.48.3Finishing with Deluxe Multi surface paint system for interiors and exteriors usingprimer as per manufacturers specifications:Painting Steel work with Deluxe MultiSurface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqmover an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand andmanufacture |
| 252 | 5.33.1.1Providing and laying in position ready mixed or site batched design mix cementconcrete for reinforced cement concrete work; using coarse aggregate and fineaggregate derived from natural sources, Portland Pozzolana / Ordinary Portland/Portland Slag cement, admixtures in recommended proportions as per IS: 9103 toaccelerate / retard setting of concrete, to improve durability and workability withoutimpairing strength; including pumping of concrete to site of laying, curing, carriagefor all leads; but excluding the cost of centering, shuttering, finishing andreinforcement as per direction of the engineer-in-charge; for the following grades ofconcrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cementAll work upto plinth levelConcrete of M25 grade with minimum cement content of 330 kg /cum |
| 253 | OD129930/2026-2027Providing and fixing roofing with Sandwich PUF panel sheets of 40-30mm thickness(color, size, shape and pitch of corrugation as approved by Engineer-in-charge).Facial on either side of panels is 0.50mm thick Pre-Coated Galvanized Steel sheets (+0.05%), total coated thickness with zinc coating 275grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 meter or as desired by Engineer-in-charge. Sandwich core is of Polyurethane Foam having modular density 40kg/cum, compressive strength 1.2kg/sqm as per BS 43 to 1960. The sheet shall be fixed using self-drilling/selftapping screws of size (8x100mm) with EPDM seal, and the edges should be covered with profile sheets, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 254 | OD129931/2026-2027Supplying and installation of PVC Louver panels as per standard sizes fixed withrubber based adhesive in both vertical and horizontal surfaces. PVC louver panels 16mm thick |
| 255 | OD131658/2026-2027Supply and fixing of PVC gutter at required slope, including all cost of clamps , othermaterial and labour charges etc complete as directed by Engineer in charge |
| 256 | 50.18.9.19.1Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00m spacing . This includes jointing of pipes with one step PVC solvent cement andtesting of joints complete as per direction of Engineer-in-Charge 110 mm dia 6Kgf/cm2 - External work- Exposed on wall |
| 257 | 50.18.9.10.1Providing and fixing PVC pipes includings jointing of pipes with one step pvc solventcement, trenching , refilling & testing of joints complete as per direction ofEngineer in Charge. 150 mm dia 6 Kgf/cm2 |
| 258 | 14.72Providing and fixing double scaffolding system (cup lock type) on the exterior side,upto seven story hight made with 40 mm dia. M.S. tube 1.5 m centre to centre,horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staricase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required location with essential safety features for the workmen etc. complete as per directions and approval of Engineer- in Charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. Note:- This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done |
| 259 | OD132778/2026-2027Design, Manufacture, supply, installation, testing and commissioning of Automaticpassenger lift of 680 kg capacity (10 passengers), rated speed 1.0 m/s, serving Ground + 3 floors (4 stops), with MRL gearless traction machine, microprocessor-based controller, simplex full collective operation, SS 304 hairline-finish car enclosure of size 1300 × 1350 × 2300 mm, automatic car and landing doors of clear opening 1000 × 2000 mm, car operating panel, landing indicators, ARD, infrared safety curtain, intercom, emergency alarm, overload protection and all mandatory safety devices, guide rails, counterweight, suspension system, wiring, earthing and standard accessories, complete with installation, testing, commissioning and suitable for the 2000 × 2500 mm RCC lift shaft, including all labour, transportation and incidental items, conforming to the applicable IS 17900 standards, relevant statutory and safety requirements, complete in all respects as per approved specifications and directions of the Engineer-in-Charge (Any defects arrising during the defect liability period shall be born by the contractor). Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 31, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysNov 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender