Tender For Various Development Works From Sectors-6 To Sector-8 And Installation Work Of Street Lights In All Sectors Of The Proposed Anand Kashi Township, Varanasi.
Tender Overview
Project Description
Tender for Various Development Works From Sectors-6 To Sector-8 And Installation Work Of Street Lights In All Sectors Of The Proposed Anand Kashi Township, Varanasi.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 04-Nov-2026 | Regarding Lighting Work Terms and Condition | Other | 20-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | SEC-6 BITUMEN ROAD |
| 2 | Surface dressing of the ground including removing vegetation and in- equlaities not exceeding 15cm deep and disposal of rubbish , lead upto 50m and lift upto 1.5m . All kinds of soil 9.0 M,12M WIDE ROAD |
| 3 | Excavating, supplying, stacking and filling of local earth (excluding royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.9.0 M,12M WIDE ROAD |
| 4 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. |
| 5 | Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density). 9.0 M,12M WIDE ROAD |
| 6 | Granular Sub base with graded Material (Table:- 400-1) By Mix in Place Method Construction of granular sub-base by providing close grader on prepared surface, mixing by mix in place method with vibratory roller to archieve the desired d density, complete as per clause -401 (AR) 9.0 M,12M WIDE ROAD |
| 7 | Construction of dry lean cement concrete sub base over a prepared subgrade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge. 9.0 M WIDE ROAD |
| 8 | Wet Mix Macadam (plant Mix Method) Providing, laying, spreading and comacting graded stone aggegate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub-base /base course on well preared surface and compacting with vibratory roller to achieve the desired density. (AR)12.0 M WIDE ROAD |
| 9 | Prime Coat over WMM/WBM Providing and applying primer coat with SS-2 grade bitumen emulsion on prepared surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means. (AR)12.0 M WIDE ROAD |
| 10 | Dense graded bituminous macadam Providing and laying dence graded bituminus macadam with higher capacity HMP using crushed aggregates of specified grading, premixxed with bituminus binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieved the desired compaction as per MoRTH specifcation clause No. 505 complete in all respects. (AR) 12.0 M WIDE ROAD |
| 11 | Tack Coat on Bituminous Surface Providing and applying tack coat with bitumen VG-10using bitumen pressure distributor at of 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. (AR)12.0 M WIDE ROAD |
| 12 | Providing and laying design mix cement concrete of M-30 grade, in roads/taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineerin-charge(Item of joint fillers, sealants, dowel bars with sleeve/tie bars to be paid separately). Cement concrete manufactured in automatic batching plant (RMC plant) including transportation to site in transit mixer |
| 13 | Bituminus Concrete Providing and laying bituminus concrete with higher capacity hot mix plant using crushed agrregate of specied grading. premixed with bituminus binder @5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and aligment rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH spcification clause No. 507 complete in all respects.(AR) 12.0 M WIDE ROAD |
| 14 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.9.0 M WIDE ROAD |
| 15 | Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)9.0 M WIDE ROAD |
| 16 | Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. |
| 17 | Providing, supplying, laying, jointing, testing and commissioning Double Wall Corrugated (DWC) HDPE Sewer Pipe conforming to IS 16098 (Part 2) and latest amendments, manufactured from virgin HDPE material with corrugated outer wall and smooth inner wall, having minimum ring stiffness of SN-8 (8 kN/m²), suitable for underground gravity sewerage applications. The pipe shall be provided with integral socket/spigot ends or HDPE couplers with EPDM rubber sealing rings to ensure watertight joints. The work shall include bed preparation, laying to required line and gradient, jointing, testing for leakage, backfilling with selected material, compaction, handling, loading, unloading, transportation and all accessories complete in accordance with CPHEEO Manual, manufacturer's specifications and directions of the Engineer-in-Charge. The rate shall include all labour, materials, tools, plant and equipment required for complete installation and commissioning in all respects.100 mm. dia 9.0 M,12M WIDE ROAD |
| 18 | PATH WAY ROAD SIDE 9 mtr Road PATH WAY (1.5m Wide) |
| 19 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil PATHWAY,TOE WALL |
| 20 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). PATHWAY,TOE WALL |
| 21 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 22 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: PATHWAY,TOE WALL |
| 23 | PATH WAY ROAD SIDE 12 mtr Road PATH WAY (1.8m Wide) |
| 24 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil PATHWAY,TOE WALL |
| 25 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). PATHWAY,TOE WALL |
| 26 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 27 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: PATHWAY,TOE WALL |
| 28 | SEC-6 SEWERAGE WORKS |
| 29 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia |
| 30 | Providing, supplying, laying, jointing, testing and commissioning Double Wall Corrugated (DWC) HDPE Sewer Pipe conforming to IS 16098 (Part 2) and latest amendments, manufactured from virgin HDPE material with corrugated outer wall and smooth inner wall, having minimum ring stiffness of SN-8 (8 kN/m²), suitable for underground gravity sewerage applications. The pipe shall be provided with integral socket/spigot ends or HDPE couplers with EPDM rubber sealing rings to ensure watertight joints. The work shall include bed preparation, laying to required line and gradient, jointing, testing for leakage, backfilling with selected material, compaction, handling, loading, unloading, transportation and all accessories complete in accordance with CPHEEO Manual, manufacturer's specifications and directions of the Engineer-in-Charge. The rate shall include all labour, materials, tools, plant and equipment required for complete installation and commissioning in all respects.100 mm. dia |
| 31 | 150 mm. dia. |
| 32 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :100 mm dia. R.C.C. pipe |
| 33 | 150 mm dia. R.C.C. pipe |
| 34 | Providing and laying cement concrete 1:5:10 up to haunches of S.W. pipes including bed concrete as per standard design:.100mm diameter |
| 35 | 150mm diameter |
| 36 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard designWith common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 37 | PATH WAY ROAD SIDE - Kerb Channel on both Main Road & Kerb Channel Road |
| 38 | Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size) over 75 mm bed of granular sub-base(GSB), well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete and as per direction of Engineer-in-charge 9M ROAD |
| 39 | 12M ROAD |
| 40 | STP (COST OF EXTERNAL DRAINAGE WORKS) |
| 41 | Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, for all depth, inlcuding getting out the excavted materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc, stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m: Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 42 | Open timbering in trenches including shuttering and shoring complete. (Measurement to be taken of the face area timbered)Depth not exceeding 1.5 meter |
| 43 | Providing, supplying, laying, jointing, testing and commissioning of HDPE Double Wall Corrugated (DWC) Pipe of Ring Stiffness Class SN-8, conforming to IS 16098 (Part 2), complete with push-fit socket and elastomeric rubber ring joints, laid true to line and level on a 100 mm thick Plain Cement Concrete (PCC) bed in cement concrete 1:5:10 (1 Cement : 5 Coarse Sand : 10 Graded Stone Aggregate, 40 mm nominal size), including excavation of trenches, dressing and preparation of bed, providing PCC bedding, lowering, laying and jointing of pipes, testing for leakage, backfilling in layers with selected excavated earth, compaction, disposal of surplus excavated material within the specified lead, restoration of the surface to its original condition, and all labour, materials, tools, plant, equipment and incidental works complete as per approved drawings, technical specifications and the directions of the Engineer-in-Charge.150mm diameter |
| 44 | 200mm diameter |
| 45 | 250mm diameter |
| 46 | 300 mm diameter |
| 47 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 150 mm. dia. |
| 48 | 200 mm. dia. |
| 49 | 250 mm. dia. |
| 50 | 300 mm. dia. |
| 51 | Constructing brick masonry circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement 1:4 (1 Cement : 4 Course Sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 course sand : 6 graded stone aggregate 40mm nominal size,) and making necessary channel in cement concrete 1:2:4 ( 1 cement : 2 course sand: 4 graded stone aggregate 20 mm nominal size) finised with floating coat of neat cement, all complete as per standard design:0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter con forming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay FPS (non modular) bricks of class designation 75 |
| 52 | Extra for depth for manholes: Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m |
| 53 | Constructing brick masonary circular manhole 1.22 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design:1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 54 | Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68m to 2.29m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 55 | Providing orange colour safety foot rests of minimum 6 mm thick plastic encapsulated as per IS:10910 on 12 mm dia steel bar conforming to IS:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 56 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 in width as well as 10 sqm on plan) inlcuding getting out and disposal of excavated earth lead uptp 50 m and lift uptp 1.5 m, as directed byt Enineer-in-charge. All kinds of soil |
| 57 | STP (COST OF EXTERNAL SEWERAGE WORKS) |
| 58 | Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, for all depth, inlcuding getting out the excavted materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc, stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m:Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 59 | Pipes, cables etc. exceeding 300 mm dia. but not exceeding 600 mm dia |
| 60 | Open timbering in trenches including shuttering and shoring complete. (Measurement to be taken of the face area timbered) Depth not exceeding 1.5 meter |
| 61 | Depth 1.5 to 3.00 meter |
| 62 | Depth exceeding 3 m but not exceeding 4.5 m |
| 63 | Providing, supplying, laying, jointing, testing and commissioning of HDPE Double Wall Corrugated (DWC) Pipe of Ring Stiffness Class SN-8, conforming to IS 16098 (Part 2), complete with push-fit socket and elastomeric rubber ring joints, laid true to line and level on a 100 mm thick Plain Cement Concrete (PCC) bed in cement concrete 1:5:10 (1 Cement : 5 Coarse Sand : 10 Graded Stone Aggregate, 40 mm nominal size), including excavation of trenches, dressing and preparation of bed, providing PCC bedding, lowering, laying and jointing of pipes, testing for leakage, backfilling in layers with selected excavated earth, compaction, disposal of surplus excavated material within the specified lead, restoration of the surface to its original condition, and all labour, materials, tools, plant, equipment and incidental works complete as per approved drawings, technical specifications and the directions of the Engineer-in-Charge.200mm diameter |
| 64 | 250mm diameter |
| 65 | 600mm diameter |
| 66 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design200 mm. dia. |
| 67 | 250 mm. dia. |
| 68 | 600 mm dia |
| 69 | Constructing brick masonry circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement 1:4 (1 Cement : 4 Course Sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 course sand : 6 graded stone aggregate 40mm nominal size,) and making necessary channel in cement concrete 1:2:4 ( 1 cement : 2 course sand: 4 graded stone aggregate 20 mm nominal size) finised with floating coat of neat cement, all complete as per standard design:0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter con forming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay FPS (non modular) bricks of class designation 75 |
| 70 | Extra for depth for manholes: Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m |
| 71 | Constructing brick masonary circular manhole 1.22 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design:1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 72 | Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68m to 2.29m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 73 | Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 74 | Extra depth for circular type manhole 1.52 m internal dia (at bottom)beyond 2.30 m :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 75 | Providing orange colour safety foot rests of minimum 6 mm thick plastic encapsulated as per IS:10910 on 12 mm dia steel bar conforming to IS:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 76 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 in width as well as 10 sqm on plan) inlcuding getting out and disposal of excavated earth lead uptp 50 m and lift uptp 1.5 m, as directed byt Enineer-in-charge. |
| 77 | VDA SEWER STORM WATER & WATER SUPPLY |
| 78 | Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :100 mm dia Ductile Iron Class K-9 pipes |
| 79 | 150 mm dia Ductile Iron Class K-9 pipes |
| 80 | Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately)100 mm dia |
| 81 | 150 mm dia |
| 82 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 25 mm nominal bore : |
| 83 | 32 mm nominal bore |
| 84 | 80 mm nominal bore |
| 85 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Cold Water Supply System.) 25 mm nominal dia Pipes |
| 86 | 32 mm nominal dia Pipes |
| 87 | 65 mm nominal dia Pipes |
| 88 | 80 mm nominal dia Pipes |
| 89 | Providing and fixing brass ferrule with CI mounth cover including boring and tapping the main 25 mm nominal bore |
| 90 | Providing and fixing water meter flange end woltman water meter class A type. 80 MM DIA |
| 91 | Providing and fixing motorized butterfly valves the valve should be able to oprate with hot/cold water medium between 20---120 degree working temperature, the nominal pressure of the valve should be PN 16, leakage rate through the valve disc should be Rate-A Bubble tight to EN1266-1 with integrated flange sealing should ensure positive connection of the valve body seat ring and valve disc and provide a complete isolation of the media from the body. The disc casting should be precision machined and should give a smooth and close disc-to-seat relationship. The stem bearing should comprise of non corrosive PTFE bushing to completely isolate the valve seat from the body, resulting in increase control of the valve disc, lower valve seating torque and longer valve life. The disc should be stainless steel to offer a good corrosion resistance, superior resistance to a broad range of chemical enviorments as well as very low co-efficient of friction and excellent resistance to impact and ultra-violet radiation. For temperatures and rust proof operation the valve disc should be stainless steel material. 150 MM DIA Basic Rate |
| 92 | External Cold Water Supply |
| 93 | Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 100 mm dia Ductile Iron Class K-9 pipes: |
| 94 | 150 mm dia Ductile Iron Class K-9 pipes |
| 95 | Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately) 100 mm dia |
| 96 | 150 mm dia |
| 97 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore |
| 98 | 32 mm nominal bore |
| 99 | 65 mm nominal bore |
| 100 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Cold Water Supply System.)25 mm nominal dia Pipes |
| 101 | 32 mm nominal dia Pipes |
| 102 | 65 mm nominal dia Pipes |
| 103 | 80 mm nominal dia Pipes |
| 104 | Providing and fixing brass ferrule with CI mounth cover including boring and tapping the main 25 mm nominal bore |
| 105 | Providing and fixing water meter flange end woltman water meter class A type 80 MM DIA . |
| 106 | Providing and fixing motorized butterfly valves the valve should be able to oprate with hot/cold water medium between 20---120 degree working temperature, the nominal pressure of the valve should be PN 16, leakage rate through the valve disc should be Rate-A Bubble tight to EN1266-1 with integrated flange sealing should ensure positive connection of the valve body seat ring and valve disc and provide a complete isolation of the media from the body. The disc casting should be precision machined and should give a smooth and close disc-to-seat relationship. The stem bearing should comprise of non corrosive PTFE bushing to completely isolate the valve seat from the body, resulting in increase control of the valve disc, lower valve seating torque and longer valve life. The disc should be stainless steel to offer a good corrosion resistance, superior resistance to a broad range of chemical enviorments as well as very low co-efficient of friction and excellent resistance to impact and ultra-violet radiation. For temperatures and rust proof operation the valve disc should be stainless steel material. 150 MM DIA Basic Rate |
| 107 | SEC-7 |
| 108 | Surface dressing of the ground including removing vegetation and in- equlaities not exceeding 15cm deep and disposal of rubbish , lead upto 50m and lift upto 1.5m . All kinds of soil 9.0 M WIDE ROAD |
| 109 | 12.0 M WIDE ROAD |
| 110 | Excavating, supplying, stacking and filling of local earth (excluding royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. 9.0 M WIDE ROAD |
| 111 | Excavating, supplying, stacking and filling of local earth (excluding royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. 9.0 M WIDE ROAD |
| 112 | 12.0 M WIDE ROAD |
| 113 | Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density). 9.0 M WIDE ROAD |
| 114 | 12.0 M WIDE ROAD |
| 115 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. 9.0 M WIDE ROAD |
| 116 | 12.0 M WIDE ROAD |
| 117 | Granular Sub base with graded Material (Table:- 400-1) By Mix in Place Method Construction of granular sub-base by providing close grader on prepared surface, mixing by mix in place method with vibratory roller to archieve the desired d density, complete as per clause -401 (AR) 9.0 M WIDE ROAD |
| 118 | 12.0 M WIDE ROAD |
| 119 | Construction of dry lean cement concrete sub base over a prepared subgrade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge. 9.0 M WIDE ROAD |
| 120 | Wet Mix Macadam (plant Mix Method) Providing, laying, spreading and comacting graded stone aggegate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub-base /base course on well preared surface and compacting with vibratory roller to achieve the desired density. (AR) 12.0 M WIDE ROAD |
| 121 | Prime Coat over WMM/WBM Providing and applying primer coat with SS-2 grade bitumen emulsion on prepared surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means. (AR) 12.0 M WIDE ROAD |
| 122 | Dense graded bituminous macadam Providing and laying dence graded bituminus macadam with higher capacity HMP using crushed aggregates of specified grading, premixxed with bituminus binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieved the desired compaction as per MoRTH specifcation clause No. 505 complete in all respects. (AR) 12.0 M WIDE ROAD |
| 123 | Tack Coat on Bituminous Surface Providing and applying tack coat with bitumen VG-10using bitumen pressure distributor at of 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. (AR) 12.0 M WIDE ROAD |
| 124 | Providing and laying design mix cement concrete of M-30 grade, in roads/taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineerin-charge (Item of joint fillers, sealants, dowel bars with sleeve/tie bars to be paid separately). Cement concrete manufactured in automatic batching plant (RMC plant) including transportation to site in transit mixer |
| 125 | Bituminus Concrete Providing and laying bituminus concrete with higher capacity hot mix plant using crushed agrregate of specied grading. premixed with bituminus binder @5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and aligment rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH spcification clause No. 507 complete in all respects.(AR) 9.0 M WIDE ROAD |
| 126 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. 9.0 M WIDE ROAD |
| 127 | Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A 9.0 M WIDE ROAD |
| 128 | Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. 9.0 M WIDE ROAD |
| 129 | Providing, supplying, laying, jointing, testing and commissioning Double Wall Corrugated (DWC) HDPE Sewer Pipe conforming to IS 16098 (Part 2) and latest amendments, manufactured from virgin HDPE material with corrugated outer wall and smooth inner wall, having minimum ring stiffness of SN-8 (8 kN/m²), suitable for underground gravity sewerage applications. The pipe shall be provided with integral socket/spigot ends or HDPE couplers with EPDM rubber sealing rings to ensure watertight joints. The work shall include bed preparation, laying to required line and gradient, jointing, testing for leakage, backfilling with selected material, compaction, handling, loading, unloading, transportation and all accessories complete in accordance with CPHEEO Manual, manufacturer's specifications and directions of the Engineer-in-Charge. The rate shall include all labour, materials, tools, plant and equipment required for complete installation and commissioning in all respects 9.0 M WIDE ROAD |
| 130 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia |
| 131 | Providing, supplying, laying, jointing, testing and commissioning Double Wall Corrugated (DWC) HDPE Sewer Pipe conforming to IS 16098 (Part 2) and latest amendments, manufactured from virgin HDPE material with corrugated outer wall and smooth inner wall, having minimum ring stiffness of SN-8 (8 kN/m²), suitable for underground gravity sewerage applications. The pipe shall be provided with integral socket/spigot ends or HDPE couplers with EPDM rubber sealing rings to ensure watertight joints. The work shall include bed preparation, laying to required line and gradient, jointing, testing for leakage, backfilling with selected material, compaction, handling, loading, unloading, transportation and all accessories complete in accordance with CPHEEO Manual, manufacturer's specifications and directions of the Engineer-in-Charge. The rate shall include all labour, materials, tools, plant and equipment required for complete installation and commissioning in all respects. 100 mm. dia |
| 132 | 150 mm. dia. |
| 133 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :100 mm dia. R.C.C. pipe |
| 134 | 150 mm dia. R.C.C. pipe |
| 135 | Providing and laying cement concrete 1:5:10 up to haunches of S.W. pipes including bed concrete as per standard design:100mm diameter . |
| 136 | 150mm diameter |
| 137 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 138 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
| 139 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).PATHWAY & TOE WALL |
| 140 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 141 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 142 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
| 143 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). |
| 144 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 145 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 146 | Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size) over 75 mm bed of granular sub-base(GSB), well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete and as per direction of Engineer-in-charge 9M ROAD |
| 147 | 12M ROAD |
| 148 | Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, for all depth, inlcuding getting out the excavted materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc, stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m: Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 149 | Open timbering in trenches including shuttering and shoring complete. (Measurement to be taken of the face area timbered) Depth not exceeding 1.5 meter |
| 150 | Providing, supplying, laying, jointing, testing and commissioning of HDPE Double Wall Corrugated (DWC) Pipe of Ring Stiffness Class SN-8, conforming to IS 16098 (Part 2), complete with push-fit socket and elastomeric rubber ring joints, laid true to line and level on a 100 mm thick Plain Cement Concrete (PCC) bed in cement concrete 1:5:10 (1 Cement : 5 Coarse Sand : 10 Graded Stone Aggregate, 40 mm nominal size), including excavation of trenches, dressing and preparation of bed, providing PCC bedding, lowering, laying and jointing of pipes, testing for leakage, backfilling in layers with selected excavated earth, compaction, disposal of surplus excavated material within the specified lead, restoration of the surface to its original condition, and all labour, materials, tools, plant, equipment and incidental works complete as per approved drawings, technical specifications and the directions of the Engineer-in-Charge. 150mm diameter |
| 151 | 200mm diameter |
| 152 | 250mm diameter |
| 153 | 300 mm diameter |
| 154 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 150 mm. dia. |
| 155 | 200 mm. dia. |
| 156 | 250 mm. dia. |
| 157 | 300 mm. dia. |
| 158 | 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay FPS (non modular) bricks of class designation 75 |
| 159 | Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m |
| 160 | 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 161 | Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68m to 2.29m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 162 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 in width as well as 10 sqm on plan) inlcuding getting out and disposal of excavated earth lead uptp 50 m and lift uptp 1.5 m, as directed byt Enineer-in-charge.All kinds of soil |
| 163 | Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, for all depth, inlcuding getting out the excavted materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc, stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m: Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 164 | Pipes, cables etc. exceeding 300 mm dia. but not exceeding 600 mm dia |
| 165 | Open timbering in trenches including shuttering and shoring complete. (Measurement to be taken of the face area timbered) Depth not exceeding 1.5 meter |
| 166 | Depth 1.5 to 3.00 meter |
| 167 | Depth exceeding 3 m but not exceeding 4.5 m |
| 168 | Providing, supplying, laying, jointing, testing and commissioning of HDPE Double Wall Corrugated (DWC) Pipe of Ring Stiffness Class SN-8, conforming to IS 16098 (Part 2), complete with push-fit socket and elastomeric rubber ring joints, laid true to line and level on a 100 mm thick Plain Cement Concrete (PCC) bed in cement concrete 1:5:10 (1 Cement : 5 Coarse Sand : 10 Graded Stone Aggregate, 40 mm nominal size), including excavation of trenches, dressing and preparation of bed, providing PCC bedding, lowering, laying and jointing of pipes, testing for leakage, backfilling in layers with selected excavated earth, compaction, disposal of surplus excavated material within the specified lead, restoration of the surface to its original condition, and all labour, materials, tools, plant, equipment and incidental works complete as per approved drawings, technical specifications and the directions of the Engineer-in-Charge.200mm diameter |
| 169 | 250mm diameter |
| 170 | 300 mm diameter |
| 171 | 450mm diameter |
| 172 | 600mm diameter |
| 173 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 200 mm. dia. |
| 174 | 250 mm. dia. |
| 175 | 300 mm. dia. |
| 176 | 450 mm dia |
| 177 | 600 mm dia |
| 178 | 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay FPS (non modular) bricks of class designation 75 |
| 179 | Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m |
| 180 | 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately): With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 181 | Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68m to 2.29m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 182 | 2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 183 | Extra depth for circular type manhole 1.52 m internal dia (at bottom)beyond 2.30 m :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 184 | Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :100 mm dia Ductile Iron Class K-9 pipes |
| 185 | Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately) 100 mm dia |
| 186 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore |
| 187 | 32 mm nominal bore |
| 188 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Cold Water Supply System.) 25 mm nominal dia Pipes |
| 189 | 32 mm nominal dia Pipes |
| 190 | Providing and fixing brass ferrule with CI mounth cover including boring and tapping the main 25 mm nominal bore |
| 191 | Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :100 mm dia Ductile Iron Class K-9 pipes |
| 192 | Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately)100 mm dia |
| 193 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore |
| 194 | 32 mm nominal bore |
| 195 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Cold Water Supply System. )25 mm nominal dia Pipes |
| 196 | 32 mm nominal dia Pipes |
| 197 | Providing and fixing brass ferrule with CI mounth cover including boring and tapping the main 25 mm nominal bore |
| 198 | SEC-8 BITUMEN ROAD |
| 199 | Surface dressing of the ground including removing vegetation and in- equlaities not exceeding 15cm deep and disposal of rubbish , lead upto 50m and lift upto 1.5m . All kinds of soil 9.0 M,12 M WIDE ROAD |
| 200 | Excavating, supplying, stacking and filling of local earth (excluding royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. 9.0 M,12 M WIDE ROAD |
| 201 | Excavating, supplying, stacking and filling of local earth (excluding royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. 9.0 M,12 M WIDE ROAD |
| 202 | Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density). 9.0 M,12 M WIDE ROAD |
| 203 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. 9.0 M,12 M WIDE ROAD |
| 204 | Granular Sub base with graded Material (Table:- 400-1) By Mix in Place Method Construction of granular sub-base by providing close grader on prepared surface, mixing by mix in place method with vibratory roller to archieve the desired d density, complete as per clause -401 (AR) 9.0 M,12 M WIDE ROAD |
| 205 | Construction of dry lean cement concrete sub base over a prepared subgrade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge. 9.0 M WIDE ROAD |
| 206 | Wet Mix Macadam (plant Mix Method) Providing, laying, spreading and comacting graded stone aggegate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub-base /base course on well preared surface and compacting with vibratory roller to achieve the desired density. (AR) 12.0 M WIDE ROAD |
| 207 | Prime Coat over WMM/WBM Providing and applying primer coat with SS-2 grade bitumen emulsion on prepared surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means. (AR)12.0 M WIDE ROAD |
| 208 | Dense graded bituminous macadam Providing and laying dence graded bituminus macadam with higher capacity HMP using crushed aggregates of specified grading, premixxed with bituminus binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieved the desired compaction as per MoRTH specifcation clause No. 505 complete in all respects. (AR)12.0 M WIDE ROAD |
| 209 | Tack Coat on Bituminous Surface Providing and applying tack coat with bitumen VG-10using bitumen pressure distributor at of 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. (AR)12.0 M WIDE ROAD |
| 210 | Providing and laying design mix cement concrete of M-30 grade, in roads/taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineerin-charge(Item of joint fillers, sealants, dowel bars with sleeve/tie bars to be paid separately). Cement concrete manufactured in automatic batching plant (RMC plant) including transportation to site in transit mixer 9.0 M WIDE ROAD |
| 211 | Bituminus Concrete Providing and laying bituminus concrete with higher capacity hot mix plant using crushed agrregate of specied grading. premixed with bituminus binder @5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and aligment rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH spcification clause No. 507 complete in all respects.(AR)12.0 M WIDE ROAD |
| 212 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.9.0 M WIDE ROAD |
| 213 | Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)9.0 M WIDE ROAD |
| 214 | Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. 9.0 M WIDE ROAD |
| 215 | Providing, supplying, laying, jointing, testing and commissioning Double Wall Corrugated (DWC) HDPE Sewer Pipe conforming to IS 16098 (Part 2) and latest amendments, manufactured from virgin HDPE material with corrugated outer wall and smooth inner wall, having minimum ring stiffness of SN-8 (8 kN/m²), suitable for underground gravity sewerage applications. The pipe shall be provided with integral socket/spigot ends or HDPE couplers with EPDM rubber sealing rings to ensure watertight joints. The work shall include bed preparation, laying to required line and gradient, jointing, testing for leakage, backfilling with selected material, compaction, handling, loading, unloading, transportation and all accessories complete in accordance with CPHEEO Manual, manufacturer's specifications and directions of the Engineer-in-Charge. The rate shall include all labour, materials, tools, plant and equipment required for complete installation and commissioning in all respects.9.0 M WIDE ROAD |
| 216 | 12.0 M WIDE ROAD |
| 217 | PATH WAY ROAD SIDE 9 mtr Road (1.5m Wide) |
| 218 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
| 219 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). |
| 220 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 221 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 222 | PATH WAY ROAD SIDE 12 mtr Road (1.8m Wide) |
| 223 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
| 224 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). |
| 225 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 226 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 227 | SEC-8 SEWERAGE WORKS |
| 228 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia |
| 229 | Providing, supplying, laying, jointing, testing and commissioning Double Wall Corrugated (DWC) HDPE Sewer Pipe conforming to IS 16098 (Part 2) and latest amendments, manufactured from virgin HDPE material with corrugated outer wall and smooth inner wall, having minimum ring stiffness of SN-8 (8 kN/m²), suitable for underground gravity sewerage applications. The pipe shall be provided with integral socket/spigot ends or HDPE couplers with EPDM rubber sealing rings to ensure watertight joints. The work shall include bed preparation, laying to required line and gradient, jointing, testing for leakage, backfilling with selected material, compaction, handling, loading, unloading, transportation and all accessories complete in accordance with CPHEEO Manual, manufacturer's specifications and directions of the Engineer-in-Charge. The rate shall include all labour, materials, tools, plant and equipment required for complete installation and commissioning in all respects.100 mm. dia |
| 230 | 150 mm. dia. |
| 231 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :100 mm dia. R.C.C. pipe |
| 232 | 150 mm dia. R.C.C. pipe |
| 233 | Providing and laying cement concrete 1:5:10 up to haunches of S.W. pipes including bed concrete as per standard design:.100mm diameter |
| 234 | 150mm diameter |
| 235 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard designWith common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 236 | PATH WAY ROAD SIDE - KC DRAIN |
| 237 | Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size) over 75 mm bed of granular sub-base(GSB), well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete and as per direction of Engineer-in-charge9M ROAD |
| 238 | 12M ROAD |
| 239 | STP (COST OF EXTERNAL DRAINAGE WORKS) |
| 240 | Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, for all depth, inlcuding getting out the excavted materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc, stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m:Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 241 | Open timbering in trenches including shuttering and shoring complete. (Measurement to be taken of the face area timbered) Depth not exceeding 1.5 meter |
| 242 | Providing, supplying, laying, jointing, testing and commissioning of HDPE Double Wall Corrugated (DWC) Pipe of Ring Stiffness Class SN-8, conforming to IS 16098 (Part 2), complete with push-fit socket and elastomeric rubber ring joints, laid true to line and level on a 100 mm thick Plain Cement Concrete (PCC) bed in cement concrete 1:5:10 (1 Cement : 5 Coarse Sand : 10 Graded Stone Aggregate, 40 mm nominal size), including excavation of trenches, dressing and preparation of bed, providing PCC bedding, lowering, laying and jointing of pipes, testing for leakage, backfilling in layers with selected excavated earth, compaction, disposal of surplus excavated material within the specified lead, restoration of the surface to its original condition, and all labour, materials, tools, plant, equipment and incidental works complete as per approved drawings, technical specifications and the directions of the Engineer-in-Charge.150mm diameter |
| 243 | 200mm diameter |
| 244 | 250mm diameter |
| 245 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design150 mm. dia. |
| 246 | 200 mm. dia. |
| 247 | 250 mm. dia. |
| 248 | Constructing brick masonry circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement 1:4 (1 Cement : 4 Course Sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 course sand : 6 graded stone aggregate 40mm nominal size,) and making necessary channel in cement concrete 1:2:4 ( 1 cement : 2 course sand: 4 graded stone aggregate 20 mm nominal size) finised with floating coat of neat cement, all complete as per standard design:0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter con forming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) With common burnt clay FPS (non modular) bricks of class designation 75 |
| 249 | Extra for depth for manholes: Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m |
| 250 | Constructing brick masonary circular manhole 1.22 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design:1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately)With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 251 | Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68m to 2.29m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 252 | Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 253 | Extra depth for circular type manhole 1.52 m internal dia (at bottom)beyond 2.30 m :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 254 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 in width as well as 10 sqm on plan) inlcuding getting out and disposal of excavated earth lead uptp 50 m and lift uptp 1.5 m, as directed byt Enineer-in-charge. |
| 255 | STP (COST OF EXTERNAL SEWERAGE WORKS) |
| 256 | Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, for all depth, inlcuding getting out the excavted materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc, stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m:Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 257 | Pipes, cables etc. exceeding 300 mm dia. but not exceeding 600 mm dia |
| 258 | Open timbering in trenches including shuttering and shoring complete. (Measurement to be taken of the face area timbered) Depth not exceeding 1.5 meter |
| 259 | Depth 1.5 to 3.00 meter |
| 260 | Depth exceeding 3 m but not exceeding 4.5 m |
| 261 | Providing, supplying, laying, jointing, testing and commissioning of HDPE Double Wall Corrugated (DWC) Pipe of Ring Stiffness Class SN-8, conforming to IS 16098 (Part 2), complete with push-fit socket and elastomeric rubber ring joints, laid true to line and level on a 100 mm thick Plain Cement Concrete (PCC) bed in cement concrete 1:5:10 (1 Cement : 5 Coarse Sand : 10 Graded Stone Aggregate, 40 mm nominal size), including excavation of trenches, dressing and preparation of bed, providing PCC bedding, lowering, laying and jointing of pipes, testing for leakage, backfilling in layers with selected excavated earth, compaction, disposal of surplus excavated material within the specified lead, restoration of the surface to its original condition, and all labour, materials, tools, plant, equipment and incidental works complete as per approved drawings, technical specifications and the directions of the Engineer-in-Charge.200mm diameter |
| 262 | 250mm diameter |
| 263 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 200 mm. dia. |
| 264 | 250 mm. dia. |
| 265 | Constructing brick masonry circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement 1:4 (1 Cement : 4 Course Sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 course sand : 6 graded stone aggregate 40mm nominal size,) and making necessary channel in cement concrete 1:2:4 ( 1 cement : 2 course sand: 4 graded stone aggregate 20 mm nominal size) finised with floating coat of neat cement, all complete as per standard design:0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter con forming to I.S. 12592, total weight of cover and frame to benot less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay FPS (non modular) bricks of class designation 75 |
| 266 | Extra for depth for manholes: Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m |
| 267 | Constructing brick masonary circular manhole 1.22 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design:1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 268 | Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68m to 2.29m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 269 | Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 270 | Extra depth for circular type manhole 1.52 m internal dia (at bottom)beyond 2.30 m :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 271 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 in width as well as 10 sqm on plan) inlcuding getting out and disposal of excavated earth lead uptp 50 m and lift uptp 1.5 m, as directed byt Enineer-in-charge. |
| 272 | STP (COST OF EXTERNAL SEWERAGE WORKS) |
| 273 | Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :100 mm dia Ductile Iron Class K-9 pipes |
| 274 | Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately)80 mm dia |
| 275 | 100 mm dia |
| 276 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore |
| 277 | 32 mm nominal bore |
| 278 | 65 mm nominal bore |
| 279 | 80 mm nominal bore |
| 280 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Cold Water Supply System.) 25 mm nominal dia Pipes |
| 281 | 32 mm nominal dia Pipes |
| 282 | 65 mm nominal dia Pipes |
| 283 | 80 mm nominal dia Pipes |
| 284 | Providing and fixing brass ferrule with CI mounth cover including boring and tapping the main 25 mm nominal bore |
| 285 | Plumbing Works- External Cold Water Supply |
| 286 | Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :100 mm dia Ductile Iron Class K-9 pipes |
| 287 | Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately) 100 mm dia |
| 288 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore |
| 289 | 32 mm nominal bore |
| 290 | 65 mm nominal bore |
| 291 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Cold Water Supply System.)25 mm nominal dia Pipes |
| 292 | 32 mm nominal dia Pipes |
| 293 | 65 mm nominal dia Pipes |
| 294 | Providing and fixing brass ferrule with CI mounth cover including boring and tapping the main 25 mm nominal bore |
| 295 | SEC 1 - ESTIMATED COST OF EXT. STREET LIGHT WORK |
| 296 | Supply installing testing & commissioning of out door type IP66 with additional canopy street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below. (Incoming; 63 Amp. 10 KA FP MCCB 1 No.; Suitable digital contractor and timer for down & dusk; 100 Amp. TPN Alu. Bus bar; Outgoing; 32 Amp. 10KA DP MCB 10 No.; 32 Amp. 10KA FP MCB 2 No.) |
| 297 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. : 6 sq mm 2 Core |
| 298 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. : 16 sq mm 4 Core |
| 299 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. : 2 X 6 sq. mm (19mm) |
| 300 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. : 4 X 16 sq. mm (28mm) |
| 301 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required : 90 mm dia (OD-90 mm & ID-76 mm nominal) |
| 302 | Supply and burying of 40mm dia x 4.5 metres long G.I. Pipe vertically for earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing. |
| 303 | Supply and laying of 25 mm X 3mm G.I. strip from earth electrode directly in the ground as required complete in all respect. |
| 304 | Supply and fixing of 1 no. 8SWG GI wire in 15mm dia GI pipe for earthing, laid in ground or in wall duly concealed including the cost of cement, sand, labour, T&P other material required for proper completion of the work as directed at site. |
| 305 | Supply and fixing of 9 mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 155 mm & Base plate 16 mm thick) having 3 mm, thickness with single ann bracket length of I mtr. length in l :2:4 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P complete in all respect. |
| 306 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR 15 , lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty.\ System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED : junction temperature shall not rise above 90°C). 72 watt |
| 307 | SEC 2 - ESTIMATED COST OF EXT. STREET LIGHT WORK |
| 308 | Supply installing testing & commissioning of out door type IP66 with additional canopy street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below.Incoming63 Amp. 10 KA FP MCCB 1 No.Suitable digital contractor and timer for down & dusk100 Amp. TPN Alu. Bus barOutgoing 32 Amp. 10KA DP MCB 10 No. 32 Amp. 10KA FP MCB 2 No. |
| 309 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 6 sq mm 2 Core |
| 310 | 16 sq mm 4 Core |
| 311 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 6 sq. mm (19mm) |
| 312 | 4 X 16 sq. mm (28mm) |
| 313 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc.conforming to IS 14930, Part II complete with fitting and cutting,jointing etc. in the existing trench, complete as required 90 mm dia (OD-90 mm & ID-76 mm nominal) |
| 314 | Supply and fixing of 9 mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 155 mm & Base plate 16 mm thick) having 3 mm, thickness with single ann bracket length of I mtr. length in l :2:4 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P complete in all respect. |
| 315 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver asper the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5,Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR 15 , lenses for beam angle asper IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard completein all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. asrequired with Minimum 5 year OEM warranty.\ System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). 72 watt |
| 316 | SEC 3 - ESTIMATED COST OF EXT. STREET LIGHT WORK |
| 317 | Supply installing testing & commissioning of out door type IP66 with additional canopy street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below. Incoming: 63 A 10 kA FP MCCB - 1 no.; suitable digital contactor and timer for dusk & dawn; 100 A TPN Al bus bar. Outgoing: 32 A 10 kA DP MCB - 10 nos.; 32 A 10 kA FP MCB - 2 nos. |
| 318 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. : 6 sq mm 2 core |
| 319 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. : 16 sq mm 4 core |
| 320 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. : 2 x 6 sq mm (19 mm) |
| 321 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. : 4 x 16 sq mm (28 mm) |
| 322 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc.conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required : 90 mm dia (OD 90 mm & ID 76 mm nominal) |
| 323 | Supply and fixing of 9 mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 155 mm & Base plate 16 mm thick) having 3 mm, thickness with single ann bracket length of I mtr. length in l :2:4 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P complete in all respect. |
| 324 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR 15 , lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty.\ System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). 72 watt |
| 325 | SEC 4 - ESTIMATED COST OF EXT. STREET LIGHT WORK |
| 326 | Supply installing testing & commissioning of out door type IP66 with additional canopy street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below. (Incoming; 63 Amp. 10 KA FP MCCB 1 No.; Suitable digital contractor and timer for down & dusk; 100 Amp. TPN Alu. Bus bar; Outgoing; 32 Amp. 10KA DP MCB 10 No.; 32 Amp. 10KA FP MCB 2 No.) |
| 327 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. : 6 sq mm 2 Core |
| 328 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. : 16 sq mm 4 Core |
| 329 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. : 2 X 6 sq. mm (19mm) |
| 330 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. : 4 X 16 sq. mm (28mm) |
| 331 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required : 90 mm dia (OD-90 mm & ID-76 mm nominal) |
| 332 | Supply and fixing of 9 mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 155 mm & Base plate 16 mm thick) having 3 mm, thickness with single ann bracket length of I mtr. length in l :2:4 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P complete in all respect. |
| 333 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR 15 , lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty.\ System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED : junction temperature shall not rise above 90°C). 72 watt |
| 334 | SEC 5 - ESTIMATED COST OF EXT. STREET LIGHT WORK |
| 335 | Supply installing testing & commissioning of out door type IP66 with additional canopy street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below.Incoming63 Amp. 10 KA FP MCCB 1 No.Suitable digital contractor and timer for down & dusk100 Amp. TPN Alu. Bus barOutgoing32 Amp. 10KA DP MCB 10 No.32 Amp. 10KA FP MCB 2 No. |
| 336 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.6 sq mm 2 Core |
| 337 | 16 sq mm 4 Core |
| 338 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 6 sq. mm (19mm) |
| 339 | 4 X 16 sq. mm (28mm) |
| 340 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required90 mm dia (OD-90 mm & ID-76 mm nominal) |
| 341 | Supply and fixing of 9 mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 155 mm & Base plate 16 mm thick) having 3 mm, thickness with single ann bracket length of I mtr. length in l :2:4 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P complete in all respect. |
| 342 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver asper the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5,Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR 15 , lenses for beam angle asper IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard completein all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. asrequired with Minimum 5 year OEM warranty.\ System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LEDjunction temperature shall not rise above 90°C). 72 watt |
| 343 | SEC 6 - ESTIMATED COST OF EXT. STREET LIGHT WORK |
| 344 | Supply installing testing & commissioning of out door type IP66 with additional canopy street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below Incoming .63 Amp. 10 KA FP MCCB 1 NoSuitable digital contractor and timer for down & dusk.100 Amp. TPN Alu. Bus barOutgoing 32 Amp. 10KA DP MCB 10 No.32 Amp. 10KA FP MCB 2 No. |
| 345 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.6 sq mm 2 Core |
| 346 | 16 sq mm 4 Core |
| 347 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 6 sq. mm (19mm) |
| 348 | 4 X 16 sq. mm (28mm) |
| 349 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required 90 mm dia (OD-90 mm & ID-76 mm nominal) |
| 350 | Supply and fixing of 9 mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 155 mm & Base plate 16 mm thick) having 3 mm, thickness with single ann bracket length of I mtr. length in l :2:4 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P complete in all respect. |
| 351 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR 15 , lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard completein all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty.\ System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED |
| 352 | SEC 7 - ESTIMATED COST OF EXT. STREET LIGHT WORK |
| 353 | Supply installing testing & commissioning of out door type IP66 with additional canopy street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below. |
| 354 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 6 sq mm 2 Core |
| 355 | 16 sq mm 4 Core |
| 356 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 6 sq. mm (19mm) |
| 357 | 4 X 16 sq. mm (28mm) |
| 358 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required 90 mm dia (OD-90 mm & ID-76 mm nominal) |
| 359 | Supply and fixing of 9 mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 155 mm & Base plate 16 mm thick) having 3 mm, thickness with single ann bracket length of I mtr. length in l :2:4 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P complete in all respect. |
| 360 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver asper the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5,Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR 15 , lenses for beam angle asper IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard completein all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. asrequired with Minimum 5 year OEM warranty.\ System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). 72 watt |
| 361 | SEC 8 - ESTIMATED COST OF EXT. STREET LIGHT WORK |
| 362 | EXTERNAL LIGHT FEEDER PILLAR Supply installing testing & commissioning of out door type IP66 with additional canopy street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below.63 Amp. 10 KA FP MCCB 1 No.Suitable digital contractor and timer for down & dusk100 Amp. TPN Alu. Bus bar 32 Amp. 10KA DP MCB 10 No.32 Amp. 10KA FP MCB 2 No. |
| 363 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.6 sq mm 2 Core |
| 364 | 16 sq mm 4 Core |
| 365 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 6 sq. mm (19mm) |
| 366 | 4 X 16 sq. mm (28mm) |
| 367 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required 90 mm dia (OD-90 mm & ID-76 mm nominal) |
| 368 | Supply and fixing of 9 mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 155 mm & Base plate 16 mm thick) having 3 mm, thickness with single ann bracket length of I mtr. length in l :2:4 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P complete in all respect. |
| 369 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR 15 , lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty.\ System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). 72 watt Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Tender Published
Tender notice published.
CompletedCorrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
TodayBid Submission Deadline
Online submission via eProcurement portal.
TodayTender Documents
Download All (ZIP) ↓We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender