Tender For Renovation Of Ward Vikash Kendra As Urban Health And Wellness Centre At Ward No -28 Under Jhumri Telaiya Municipal Council
Tender Value
24.95 Lakhs
Estimated cost
Bid Submission
14 Nov 2026
13 days left
EMD
49936
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Koderma → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Ward Vikash Kendra As Urban Health And Wellness Centre At Ward No -28 Under Jhumri Telaiya Municipal Council
BOQ
| Sl. No. | Item Description |
| 1 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.To repair damaged plaster patch |
| 2 | Providing average 115 mm thick lime terracing for roof |
| 3 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 4 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10sqm over and including priming coat of exterior primerapplied @ 2.20 kg/ 10 sqm) |
| 5 | Providing two coats of paintings on steel surfaces Collapsible gate ( 1.5 coefficiant factor for area calculation )Window Grill (1 coefficiant factor for area calculation )stair railings |
| 6 | Providing two coats of paintings on wooden surfaces |
| 7 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architecturaldrawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : --- For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 8 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.0 mm thickness (weight not less than 10kg/sqm) |
| 9 | Filling the gap in between aluminium frame & adjacent RCC/Brick/ Upto 5mm depth and 5 mm width |
| 10 | Providing and fixing aluminium extruded section body tubular type |
| 11 | Supplying fitting and fixing aluminium fittings of approved quality and |
| 12 | 300x16 mm sliding Door Bolt |
| 13 | 250x16 mm Sliding Door Bolt |
| 14 | Providing and fixing aluminium hanging floor door stopper ISI marked |
| 15 | Twin rubber stopper |
| 16 | Aluminium casement stays (anodic coating not less than grade AC 10 as per IS : 1868) transparent or |
| 17 | Providing and fixing bright finished brass 100 mm mortice latch and and lock |
| 18 | 3.0 mm thick & 2100 mm long with SS screws etc.complete as per |
| 19 | Providing and laying concrete in kerbs , steps of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 20 | Providing and laying vitrified pairin/ industrial tiles All complete as per building specification and direction of E/I. |
| 21 | Providing and laying Double charge vitrified floor tiles in different sizes All complete as per building specification and direction of E |
| 22 | Taking down double layer tiles |
| 23 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 for Toilet |
| 24 | Providing and laying rectified Glazed Ceramic floor tiles of size 300X 300 mm for Toilet |
| 25 | Earth in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts, levelling ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I. |
| 26 | Stone crusher dust finer than 3mm with not more than 10% passing 0.075 seive at crusher (filling) |
| 27 | Providing and laying cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm (nominal size) excluding the cost of centering, shuttering and finishing - All work up to plinth level ,complete as per building specifications and direction of E/I. |
| 28 | Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer in-Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern. |
| 29 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted volume) |
| 30 | Providing designation 75B work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 Including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I. |
| 31 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement: 2 coarse sand (zone-III): 4 graded stone aggregate 40 mm nominal size) |
| 32 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 33 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 34 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 35 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 36 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 37 | Providing Toe steel reinforcement of 10mm to 16mm dia rods as approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I, TMT Fe 500 (Only Valid for SAIL, TATA Steel, JSPL, Electro Steel Ltd. and Vizal Steel) |
| 38 | 10mm dia |
| 39 | 12mm dia |
| 40 | Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I |
| 41 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening curing with all leads and lifts of water scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 42 | Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/L. |
| 43 | Supplying, fitting and fixing viterous white glazed earthen ware I.W.C of Parry Hindustan or any other I.S.S approved make with 100mm H.C.I \\"p\\" trap 15 liters C.I. or C. pull and let go flushing cistern of names or other I.S.S equivalent make, complete with all fittings. C.I or C.C brackets 32mm alkathene/P.V.C telescopic flush, pipe about 2M long with one brass coupling and clamps G.I chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I body brass spindle stope cock of weight not less than 50 grins. 15 mm P.V.C connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.(c) 510mm Long with 10 litre low level P.V.C. cistern |
| 44 | Supplying fitting and foơng 40mm high vitreous white glazed earthen E.W.C. with 'p' trap of pery hindustan or any other approved 1.S.S. make including supplying and fixing 15 litres C.L mosquito proof low down flushing cistern of approved make with complete fittings with C.l.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop of approved quality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commandericuckoo or other 1.3.3. make with hinges or screws etc, painting pipe and cistem etc, with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and direction of E/L |
| 45 | Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approvad make supported on painted C.l. or R.S. brackets 32mm C.Lbrass waste, 15 mm dia C.L. body brass spindle stop cock of approved quality of weight not less than 350grams 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of EL |
| 46 | Providing and foxing white vitreous china laboratory sink with Cl brackets, C.P brass chain with rubber plug 40 mm C.P brass waste and 40 mm CP brass trap with necessary C.P brass unions complete including painting of fittings and brackets, cutting and making good the wall wherever required: |
| 47 | Providing and fixing white vitreous china flat back or wall comer type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. |
| 48 | Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete |
| 49 | Providing and foing PTMT liquid soap container 109 mm wide 125 mm high and 112 mm distance from well of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less then 105 gms. |
| 50 | Providing & foxing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimurn distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms |
| 51 | Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931 |
| 52 | Providing and foxing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. |
| 53 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore. |
| 54 | C.P. brass |
| 55 | Providing and fixing flanged cleanout plug with M.S. flanged tail pieces blind flang, 6mm dia nut & bolts, gasket and washers fixed to C.L. Pipe with drip seal joint complete in all complete including cutting and making good the walls and floor wherever required |
| 56 | Providing and fixing uplasticised PVC connection pipe with brass unions: |
| 57 | Providing & fixing rain weter \\"Khurras' size 450x450 mm required depth with lead flashing around the pipe with one piece lead sheet of 3 mm thick set on a layer of cold bitumen, Including Heavy duty CMS grating as per drawing complete as required. |
| 58 | Supplying ficting and fixing H.C.L. pipes with sar of approved make confirming to LS.1. 1729 including supplying nails and bobins short pieces, cutting loose collars, lead and yam for making lead caulked joints, cutting pipes to size including earth work or scaffolding where necessary etc., all complete as par specification and direction of P |
| 59 | (a) 100 mm dia |
| 60 | (b) 75 mm dla |
| 61 | (c) 50 mm dia |
| 62 | Supplying and fixing H.C.L. fittings of approved make confirming to 1.S. 1732 including supplying nails and bobines lead and yarn from making lead caulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/1. |
| 63 | A) H.C.L single junction with door but without ear except socket (I) 100 mm dia (wt. 10.5 Kg. app.) |
| 64 | (B) H.G.I. Heal Rest bend (I) 100 mm dia (wt. 5.5 Kg. app.) |
| 65 | Supplying all tools and labours and cutting chajja. Cornice. for lavino H.C. pipes and making good the same as oer Specification and direction of EA |
| 66 | Cutting drain width wise above G.L. for laying H.C. pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in (1:4) with neat cement punning as per specification and direction |
| 67 | Making holes in walls for laying H.C.L pipes and restoring the same after pipe laying as per specification and direction of E/1. (a) 125mm dia |
| 68 | Supplying materials and labour for painting the exposed H.C. pipes and fittings with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/1. (a) 50 mm dia |
| 69 | (a) 80 mm dia |
| 70 | (a) 100 mm dia |
| 71 | Providing Fixing testing and commissioning of UPVC pipe SWR type \\"B\\" conforms to IS: 13592-1992 with all fittings such as bends, tees, elbow, Y offset cleaning pipe door, clamps and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS: 13592-1992 type 'B'. The fitting dimension conforming to IS: 14735-1999. The jointing to be completed with rubber ring joint/solvent weld joint 110 mm (OD) SWR Pipe |
| 72 | Providing and fuong G.L. pipes complete with Gl fittings and clamps including cutting and making good the walls etc. (Exposed on well Terrace) 25 mm nominal outer dia pipes |
| 73 | Providing and foxing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including foxing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the wall same including testing of joints complete as per the direction of engineer incharge Concealed work including cutting chases and making good the wall etc. |
| 74 | 15 mm nominal outer dia pipes |
| 75 | 20 mm nominal outer dia pipes |
| 76 | 25 mm nominal outer dia pipes |
| 77 | Providing and fixing of gun metal gate valve with Cl wheel of approved quality (screwed ends) 18,17.2 32 mm dia, nominal bore |
| 78 | Painting Gil pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality 18.40.3 25 mm dia, nominal bore |
| 79 | Providing and fixing G.L. union in G.L. pipe including cutting and threading the pipe and making long screws etc, complete, 18.46.4 32mm nominal bore |
| 80 | Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design, |
| 81 | Constructing masonry Chamber 60x45x50 cm, inside with 75 class designation brick work in cement mortar 1:5 (1 cement:5 fine sand) for water meter complete with C.I. Doble flap surface box 400x200x200mm (Inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement: 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortor 1:3 (1 cement 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design, |
| 82 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water light C.l. cover with frame of 300 x300 mm size (Inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: |
| 83 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1.2 (1 cement: 2 fine sandi including testing of joints als completa150 mm dia R.C.C. pipe |
| 84 | Constructing brick masonry manhole in cement mortar 1:4 (1 cement: 4 coarse sand) with R.C.C. top slab with 1:1.5:3 mix (1 cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand (zone III): 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat |
| 85 | Inside size 90 x 80 cm and 45 am deep including Cl cover with frame (light duty) 455 x 610mm intemal dimensilons total weight of cover and frame to be not less than 38 Kg. (weight of cover 23 Kg. and weight of frame 15 Kg.) with FPS bricks with clase dasianation 75 |
| 86 | With common bunt cley F.P.S. (non modular) bricks of class designation 7.5 |
| 87 | Constructing brick masonry circular type manhole 0.91 m Internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement:4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cerment, foundation concrete 1:3:6 mix (1 cement: 3 coarse sand: 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement all complete as per standard |
| 88 | Constructing brick masonry road gully chamber 50x45x60cm with bricks in cement mortar 1:4 (1 cement: 4 coarse sand) including 500x450mm precast RCC horizontal grating with frame complete as per standard design |
| 89 | With common bumt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 90 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank IS: 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet outlet and overflow pipes but withoud fittings and the hese support for tank |
| 91 | Providing storing handling shifting installation testing and commissioning of portable fire Extinguishers as described below |
| 92 | (a) 4.5 kg carbon dioxide extinguisher IS marked with high pressure discharge tube hom control valve CCE approved cylinder |
| 93 | 6 kg Mono Ammonium Phosphate (ABC) type cartridge operated extinguishers |
| 94 | Wiring for light point/ fan point/exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single care cable in surface/ recessed PVC condult with modular switch modular plate suitable Gl box etc as required. |
| 95 | Wiring for light/ power plug with 2x4 sq. mm FR PVC Insulated copper conductor single core cable in surface/ recessed PVC condult alongwith 1 No 4 sq. mm FR PVC Insulated copper conductor single core cable for leop earthing as required. |
| 96 | Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit as required |
| 97 | 2x1.5 sq mm 1x1.5 sq mm earth wire |
| 98 | 2x2.5 sq mm 1x2.5 sq mm earth wire |
| 99 | Supplying and drawing co-axial TV cable RG-6 grade 0.7 mm solid copper conductor PE Insulated shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel PVC conduit as required. |
| 100 | Supplying and foing of following sizes of PVC conduit along with the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 101 | 25mm dia |
| 102 | 32mm dia |
| 103 | Supplying and foang following moduler switch socket on the existing madular plate & switch box including connections but excluding modular plate etc as required. |
| 104 | 5/5 amps one way switch |
| 105 | 15/16 amp one way switch |
| 106 | 5/8 amp 3 pin socket outlet |
| 107 | 5/16 amp 5 pin socket outlet |
| 108 | TV anteena Sockel Outlet |
| 109 | Supplying and foang stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required. |
| 110 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 111 | Supplying and fixing following size/ modules Gl box alongwith modular base & cover plate for modular switches in recess etc as required. |
| 112 | 1 or 2 Module (78mm x 75mm x 45mm)-For Telephone & TV outlet |
| 113 | 4/5 Module (78mm x140mm x 50mm) |
| 114 | 8/9 Module (76mmX230mmx50mm) |
| 115 | Supplying and frương 2 pin 5 Amp Ceiling rose on the existing junction box wooden block Including connection etc as required. |
| 116 | Supplying and fuơng brass betten/ angle holder including connection etc. as required. |
| 117 | Supplying and foang Ding dong sound call bell single phase 230 volts complete as required. |
| 118 | Installation testing and commissioning of pre wired fluorescent fitting / Compact fluorescent fitting off all type complete with all accessories and tute etc directly / wall including connection with 1.5 sq.mm FR PVC insulatted copper conductor single core cable and earthing etc. as required. |
| 119 | Installation testing and commissioning of ceiling fan including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated copper conductor single core cable etc. as required. |
| 120 | Installation of exhaust fan up 450 mm sweep in the existing opening including making the hole to suit the size of above the fan making good the damage connection testing commissioning etc. as required. |
| 121 | Supplying and foang following ways horizontal type three pole and neutral sheet steel MCB distribution board 415 volts on surface/recess complete with tinned copper bus bar neutral bus bar earth bar din bar interconnections powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 Way (4+18) Double Door Horizontal Type |
| 122 | Supplying and fixing 6 Amp to 32 Amp rating 240 volts 10 KA \\"C\\" Curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections testing and commissioning etc. as required. |
| 123 | 6/32 Amp Single Pole |
| 124 | 6/32 Amp TPN |
| 125 | 40 Amp TPN |
| 126 | Supplying and fibing of following rating double pole (Single pole & neutral) 240 volts resudual current circuit breaker (RCCB) having a sensivity current 30 miliampere in the existing MCB DB complete with connections testing & commissioning etc as required. 63 Amps |
| 127 | Providing and fương M.V. danger Notice plate of 200mm x 150 mm of made of mild steel at least 2 mm thick and vitreous enamelded white on both side and with inscription in single red colour in front side as requird |
| 128 | Earthing with G.L. earth plate 600 mm X 600 mm X 8 mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required. |
| 129 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 130 | Supply & Laying of following sizes of 1.1KV grade multistranded copper conductor PVC insulated cable including termination complete as required in existing cable tray. |
| 131 | 1C x 16 sq.mm PVC Insulated cu wire including termination etc. |
| 132 | S.I.T.C. of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V 50 Hz Single Phase Supply etc. complete as required. |
| 133 | 10/12 W LED Tube Light |
| 134 | 20/22 W LED Tube Light |
| 135 | SITC of 300 mm (12\\") Exhaust fan (Metal body) suitable for single phase 230 volts 50 Hz. AC supply complete with motor louvers/shutters etc. complete as required. Make-Usha/Crompton / Havells. |
| 136 | Supply Installation Testing & Commissioning of following sizes ceiling fan 3 Blades confirming to IS:374:2018 including wiring the down rods of standard (up to 30cm) with 1.5 sq.mm FR PVC insulated copper wire suitable for 230V 50 Hz Single phase supply etc. complete as required. Make - Usha/Crompton / Havells. |
| 137 | 1200 mm (48\\") BLDC 5 Star rating 32W Ceiling Fan |
| 138 | Cost of drilling 200mm x 165mm x 100m deep bore well in all kinds of soil and rock in rural area for installation of pump set with D.T.H. rig all complete! including supplying all materials, labours, tools, drilling rig, air compressor and equipment as well as fuel, lubricants for making boring and cost of transporting/charges of rig machine & other vehicles up to site of the work as per specification and direction of E/l.(M1035 : DW&S) |
| 139 | (a) Up to 50 mtr Below G.L. |
| 140 | B) Beyond 51 mtr. Up to 125 mtr. Below G.L |
| 141 | Supplying all materials, labours, equipments for lowering 200mm dia M.S. ERS pipes as casing of well thickness 6mm for protecting the sites from falling during the process of drilling ail complete including carriage to work site.(M1036 : DW&S) |
| 142 | Supplying labour and equipments including 200mm dia. M.S. Cap and fitting and fixing over the tube well properly and taking it out as per direction of E/I.(M1036 : DW&S) |
| 143 | Supplying all tools, labours, equipments for lowering 32mm dia P.V.C. pipe in 3 mtr. length in the drilling bore of tube well etc. all complete job as per direction of E/I.D.S.R. 18.9.4 |
| 144 | Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, all as per requirement and direction of Engineer-in-charge.(M1042 : DW&S) |
| 145 | Supplying fitting and fixing of KSB/KIRLOSKER/CRI make 1.50 HP Submersible pump set having head of 135 metre including all taxes, royalty, etc.all complete job as per direction of E/I.(M1055 : DW&S) |
| 146 | Supplying fitting and fixing of 5 H.P. standard make starter panel board with arrangement of all necessary protection including all taxes,royalty etc all comlete job as per direction of E/I.(M1065 : DW&S) |
| 147 | Supplying fitting and fixing 3 core 4mm 2 flat copper submersible cable FINOLEX/HAVELS make including all taxes,royalty etc all complete job as per direction of E/I.(M1906 : Energy) |
| 148 | dust ( lead upto 18 km) |
| 149 | cement and steel ( lead upto 2 km) |
| 150 | sand ( lead upto 20 km) |
| 151 | stone chips( lead upto 18 km) |
| 152 | bricks ( lead upto 30 km) |
| 153 | 18 % gst |
| 154 | 1 % labour cess |
| 155 | Chairtech Low-Back Chair with Fixed armrest with Padding Backrest Height (Low-back range: 200 - 400 mm, Mid-back range: 400 - 700 mm) |
| 156 | SP ENTERPRISES--SP ENTERPRISES 2 - seater Sofa Set with No Secondary unit Secondary Unit Overall Width of Primary Unit in Sofa Set (in mm) Between 1200 to 1500 mm (between 3.9 to 4.9 ft) |
| 157 | GODREJ INTERIO Silver Grey Colored Steel Shelving Cabinets. Types of Almirah (Dimensions are without pedestal height) Small (1150 mm X 760 mm X 430 mm) |
| 158 | R L GARG FURNITURE Rectangular (Straight) Reception Table Primary Table Top Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 31, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysNov 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender