Tender For Special Repair To Bldg No. T-1 (Jco Mess) And Special Repairs To Roof Sheet And Connected Items Of Bldg No T-16 At Ch Sambhajinagar Cantt Under Ge (South) Ahilyanagar
Tender Overview
Project Description
Tender for Special Repair To Bldg No. T-1 (Jco Mess) And Special Repairs To Roof Sheet And Connected Items Of Bldg No T-16 At Ch Sambhajinagar Cantt Under Ge (South) Ahilyanagar
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 11-Nov-2026 | Corrigendum1 | Other | 20-Nov-2026 |
| 2 | 20-Nov-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 27-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement or cement lime plaster of any description on brick, block or stone walls etc (at any height) including racking out joints, hacking for key scrubbing down with water etc complete & removing debris outside MD land as directed. |
| 2 | M&L for rendering 10mm thick on in CM 1:6 fair faces of brick/concrete sufaces surfaces of walls finished even and smooth without using extra cement complete all as specified and as directed. |
| 3 | M&L for 15mm thick plaster in CM 1:4 (using water proofing liquid as per manufacturers instructions) on other than fair faces of brick work masonary surface or concrete surface finished even and fair without using extra cement complete all as specified and directed. Note :Cost of water proofing compound is deemed to be included in the rate quoted. |
| 4 | Removing the loose spalled concrete portions from Ceiling,wall ,beams,Chajja surface cleaning thoroughly by making it free of dirt, rust etc. and applying rust removing solution to exposed corroded reinforcement, applying a coat of DR. FIXIT Epoxy Zinc Primer or equivalent to the reinforcement bars, and fixing of wire mesh having 0.90 mm dia and 12 mm aperture with nails, applying 1 coat of bonding agent (DR. FIXIT Pidicrete MPB or equivalent) mixed with cement (ratio 1:1) and finally rendering the surface avg 25 mm thick with DR. FIXIT Polymer Mortar PX or equivalent complete all as specified and as directed.Note: 1. Location shall be verified and approved by the Engineer-in-charge before carrying out the treatment.2. Make of Chemical shall be approved by the GE before start of application. |
| 5 | M&L for 35mm thick precast cement concrete louvers and jallies including mouldings in precast cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate and fixed in cement mortar 1:4 including dismantling old precast louvers and jallies complete all as specified and as directed |
| 6 | M&L for brickwork with fly ash bricks (old size), straight or curved on plan, exc 6 m mean redius, built in cement mortar 1:6 with and including demolition of existing brick work built in cement or cement lime mortar of any description complete all as specified and as directed. |
| 7 | M&L for preparation of new plastered internal surfaces of wall and applying two coat of acrylic distemper of required shade and colour complete including one coat of primer as per manufacturer's specifications in any colour complete all as specified and directed. |
| 8 | M&L for newly plastered wall surfaces, preparation of surface and applying applying two coats of 100% premium exterior acrylic emulsion paint (weather coat) alkali & fungal resistance, dirt resistance of required shade over and including priming coat of exterior primer complete all as specified and as directed. |
| 9 | M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed. |
| 10 | M&L for applying 1.5 mm thick (minimum) of Birla/ JK wall care putty in new or old decorated surfaces of walls and sanding the surfaces till smooth finish is obtained for receiving finishes complete all as specified and as directed |
| 11 | M&L for Preparation of old decorated surfaces of walls and applying two coats of white wash complete all as specified . |
| 12 | M&L for preparing of old surfaces of walls, pillasters, cornices etc by washing, rubbing down & stopping etc and applying two coats of acrylic distemper in any colour complete all as specified and as directed. |
| 13 | M&L for complete removal of existing treatment on old decorated plastered suface of external walls & applying two coats of Exterior Acrylic Emulsion paint over one coat of primer including fillings of cracks with acrylic crack filler as required complete all as specified & directed by Engr in charge. |
| 14 | Taking down chowkats or frames exc. 1.5 but n.exc 4sqm each with shutters (W/o taking off shutters from the frame) and removal to store complete all as specified and as directed. |
| 15 | Taking down chowkats or frames with shutters(without taking off shutters from the frames), area n.exc 1.50 sqm each and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and as directed. |
| 16 | M & L for rolled mild steel work angle iron as in door frame (Chowkhats),cooler stand & tank stand confirming to Fe-290 (Gde E165) including preparing back of chowkhat and simlar applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed. |
| 17 | S&F mild steel framed work such as grill, gratings, guard bars etc with end of bars shouldered and/or riveted or forged into spikes and similar works conforming to Fe.290, Gde-E-165 including one shop coat of zinc chrome primer and cutting holes/making surface good in cement concrete 1:2:4 type B-0 complete all as specified. |
| 18 | M & L cement concrete type B-0 1:2:4 (12.5 mm graded agg ) as in bed block ,hold fast, coping and similar work etc complete all as specified and as directed. |
| 19 | S&F 35 mm thick, second class hard wood, plain framed, factory made, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and as directed. |
| 20 | S&F 35mm thick IInd class hard wood glazed skelton shutters,factory made,open rebated and prepared to recive glass,guage etc,(with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of sutters as specified in SSR part - I section - 8, clause 8.20 (a). S&F to chowkhat complete all as specified and as directed. |
| 21 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per specified and as directed.Note: (i) Minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable for WPC solid door/window frames. Variation in profile dimensions on plus side shall be acceptable without any extra cost to the department |
| 22 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Stainless steel butt hinges shall be paid separately under respective item. |
| 23 | S&F powder coated aluminum windows, three track, made out of aluminium sections (make Jindal or equivalent) including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed comprises of following sections :- (a) Window frame (i) Bottom- Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Size - 20672 (Wt not less than 0.594 Kg/m)(b) Shutter (i) Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)Note:- Colour to be decided by Engineer-in-Charge. |
| 24 | S&F in repair powder coated anodised aluminium ventilator having aluminium section weighing 0.55 kg/m, including Sliding louvers,frosted 3mm thick glass,SS wiremesh including arrangement for fixing of exhaust fan and necessay joining cleats,glazing clips,screws etc complete all as specified.Note:- Shade and size to be decided by Engineer-in-Charge. |
| 25 | S&F Powder coated anodized aluminium frames for door, window , ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and as directed by Engr-in-charge.Note:- Colour to be decided by Engineer-in-Charge. |
| 26 | S&F Powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified.Note:- Colour to be decided by Engineer-in-Charge. |
| 27 | S&F 0.9m to 1.5m bottom door seal brown aluminium frame 38 to 45mm width all as specified and directed. |
| 28 | M&L for preparing the new wooden surface & applying two coats of synthetic enamel paint (1st grade) over one coat of pink primer over 10Cm width or girth complete all as spd & directed. |
| 29 | M&L for preparation of new steel surfaces over 10 cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified. |
| 30 | M&L for preparation of old painted surfaces of steel of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 31 | S&F SS wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed on wooden/steel frames with tinned tacks or galvanized wire staple & complete all as specified and as directed. |
| 32 | S&F door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring ,fixed in floor over all length of cover plate 150 mm all as specified and directed. |
| 33 | S&F mild steel helical door spring 300mm ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed by Engr-in-charge. |
| 34 | S&F 100 mm long SS butt hinges, medium weight, cold rolled, ISI marked, complete all as specified and as directed. |
| 35 | S&F butt hinges medium weight cold rolled mild steel ISI marked size 100 mm size complete all as specified and directed. |
| 36 | S&F 125mm size aluminium alloy handles, fabricated type extruded section, ISI marked complete all as specified and as directed. |
| 37 | S&F 150mm size aluminium alloy handles, fabricated type extruded section, ISI marked complete all as specified and as directed. |
| 38 | S&F 100mm size stainless steel handles, for cupboard/ kitchen cabinet complete all as specified and as directed. |
| 39 | S&F for aluminum anodized barrel tower bolt of extruded section size of bolt 150mm as specified and directed. |
| 40 | S&F for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed complete all as specified and as directed. |
| 41 | S&F 200mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 42 | S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 43 | S&F in repairs aluminium extruded section door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed. |
| 44 | S&F in repairs Mild steel Chromium finsh Mortice lock, vertical type, 4 levers size 100 mm for aluminium door complete all as specified and as directed. |
| 45 | S&F as in repair for providing Cupboard/kitchen cabinet with shutters in required size at site made out of 18 mm thick PVC board one side laminated and other side plain. The panels shall be fabricated using adhesive, screwed and secure as required. All edges shall be covered with 1.5mm thick edges leaping tapes or 90 degree edge bent finish as per manufactures instructions complete all as specifed and directed. |
| 46 | S&F as in repair for providing Cupboard/kitchen cabinet Shelf in required size at site made out of 18 mm thick PVC board two side plain. The panels shall be fabricated using adhesive, screwed and secure as required. All edges shall be covered with 1.5mm thick edges leaping tapes or 90 degree edge bent finish as per manufactures instructions complete all as specifed and directed. |
| 47 | S&F continous (Piano) hinges, brass finish of when open 30mm width of flaps complete all as specified and as directed |
| 48 | S&F 100mm size hasp and staple, aluminium anodised safety type, fixed with screws complete all as specified and directed |
| 49 | S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed |
| 50 | S&F in repair magnetic catcher, Double strip (horizontal type), in cupboard/ward robe shutters including fixing wit necessary Stainless Steel screws etc. complete all as specified and as directed. |
| 51 | S&F auto closing hinges 35 mm of 0 crank (KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet/Cupboard shutters complete all as specified and as directed. Make:- KAFF or equivalent make as approved by GE |
| 52 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises all as specified and directed. |
| 53 | M&L for coloured non-skid ceramic tiles, 7 to 8 mm thick (square or rectangular), area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over & including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.Note :- Colour and shade shall be approved by Engr-in-Charge. |
| 54 | M & L for Non-skid coloured Ceramic tiles mat finish 7 to 8 mm thick ( square /Rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 sqm (600x600mm) in floors etc set and jointed in neat cement slurry and pointed in white cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), complete all as specified and directed.Note :- Colour and shade shall be approved by Engr-in-Charge. |
| 55 | Ditto all as per itemNo 54 above but as in skirting set and jointed in neat cement and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4 complete all as specified and directed. |
| 56 | M & L for Vitrified tiles double charged (light shade) 8 to 9mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm (600x600mm), in floors etc set and jointed in neat cement slurry and pointed in white cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), complete all as specified and as directed.Note :- Colour and shade shall be approved by Engr-in-Charge. |
| 57 | M&L for glazed coloured ceramic tiles in vertical surfaces as dado of size 450x300x6-7mm, thick set and jointed in neat cement and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:3 on other than fair faces of brick work etc complete all as specified & as directed.Note: Color, size and shade shall be as approved by Engineer-in-charge |
| 58 | Dismantling kota, granite, cudappa stone slabs and interlocking tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortor complete all as specified and as directed. |
| 59 | M&L for machine cut Kota stone flooring 18 to 22 mm thick (size of kota stone slab 22\\"x18\\") laid over and including 20 mm thick bedding layer of cement mortar 1:6, jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed. |
| 60 | All as per item No. 59 here-in-before but 15-18 mm thick as in risers to steps and skirting laid over and including backing coat of 10mm thick cement mortar 1:3 all as specified and as directed.Note : Riser provided to steps shall be in one piece. |
| 61 | M&L for Machine cut cudappah stone slab 20-25 mm thick laid over and incl 20 mm thick bedding layer CM 1:6 incl roughening of old concrete floor surfaces by picking, sweeping clean and washing down with water to remove dust with pigments to match the shade of slab incl cutting, rubbing and finish polishing complete all as specified and directed. |
| 62 | M & L for 18-20mm thick prepolished Granite stone slab of approved shade and colour as in table top, top of WHB, kitchen slab/plateform, gate pillars, cills etc or on vertical surfaces including vertical projections, including full round mouldings the edges laid over and over and including screed bed 15mm thick in cement mortar 1:4 jointing, pointing in white cement 1:2 using marble dust with admixture of pigments to match the shade of granite and rubbing polishing to achieve mirror finish complete all as specified & directed. Note:- Colour/shade to be decided by Engineer-in-Charge. |
| 63 | Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 64 | M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed. |
| 65 | M&L for PCC 25 mm thick (1:2:4) type B-1 using 20 mm graded stone as levelling course in floors aggregate complete all as specified & directed. |
| 66 | Taking up or down 15 mm bore dia GI steel tubing and connections complete all as specified and as directed. |
| 67 | Taking up or down 20 mm bore dia GI steel tubing and connections complete all as specified and as directed. |
| 68 | M&L for 16mm bore CPVC pipes SDR 11 & Brass CPVC SDR 11 fittings such as socket, elbow, bends, tee, reucer, union, caps plug, nipple etc complete laid in walls/ceilings or laying in floor trench or fixed to walls complete all as specified and as directed. |
| 69 | M&L for 20mm bore CPVC pipes SDR 11 &Brass CPVC SDR 11 fittings such as socket, elbow, bends, tee, reucer, union, caps plug, nipple etc complete laid in walls/ceilings or laying in floor trench or fixed to walls complete all as specified and as directed. |
| 70 | M&L brick wall or plaster cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. |
| 71 | S&F in repairs, rotational moulded polyethylene water storage tanks colour white (cylindrical vertical with closed top), 1000 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed. |
| 72 | S&F in repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 20 mm dia, ISI marked complete all as specified & as directed. |
| 73 | S&F vitreous china wash hand basin, white flat back of size 550 mm x 400 mm including brackets, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe15mm dia, PVC connection pipe 450mm long complete all as specified and as directed.Make: Cat No. S2040141 of CERA or equivalent model of makes specified. |
| 74 | S&F in repairs, vitreous china wash down water closet (pedestal pattern) white, including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws, etc. complete all as specified and as directed.Make: Cat No. S1053102 of CERA or equivalent model of makes specified. |
| 75 | S&F in repairs 10 ltr capacity PVC valve-less, syphonic action type flushing cistern, low level, white with inlet ball valve and handle including brackets complete all as specified and as directed.Make: Cat No. B1010110 of CERA or equivalent model of makes specified. |
| 76 | S&F in repair PVC connection, 15 mm size with PTMT nuts, 450 mm long complete all as specified and directed. |
| 77 | S&F in repairs PVC waste pipe 32mm bore plain 600mm long complete all as specified and as directed. |
| 78 | S&F SS Grating with square frame (Grating thk- 1mm & frame thk- 1.5mm) of size 125mm (minimum) with waste-hole complete all as specified and directed. Note: Design of grating to be approved by Engineer-in-Charge. |
| 79 | S&F SS Grating with square frame (Grating thk- 1mm & frame thk- 1.5mm) of size 100mm (minimum) with/ without waste hole as required complete all as specified and directed.Note: Design of grating to be approved by Engineer-in-Charge. |
| 80 | S&F in repair soap dish chromium plated, fixed to plugs with chromium plated screws complete all as sped & directed. |
| 81 | S&F in repairs, Health faucet (ABS Body) suitable for 15 mm dia pipe with 1 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.Make: Cat No. F8030111AB of CERA or equivalent model of makes specified. |
| 82 | S&F in repairs wall mixer for mixing hot and cold water and bend for connecting to shower, 15 mm bore screwed for iron pipe and fixed complete all as specified and as directed.Make: Cat No. F1015401 of CERA or equivalent model of makes specified. |
| 83 | S&F in repairs Central hole Wash Basin Mixer for mixing hot and cold water 15 mm bore screwed for iron pipe and fixed complete all as specified and as directed.Make: Cat No. F2014461 or F1015454 of CERA or equivalent model of makes specified. |
| 84 | S&F in repair overhead shower rose 125mm size with 200mm long shower arm and wall flange complete all as specified & directed by Engr-in-charge. Make: Cat No. F7020111AB of CERA or equivalent model of makes specified. |
| 85 | S & F in repairs, stop/ angle valves, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.Make: Cat No. F1015201 of CERA or equivalent model of makes specified. |
| 86 | S&F in repairs, bib tap 15mm dia, with wall flange and aerator screwed down for iron pipe or for brass ferrule complete all as specified and as directed.Make: Cat No. F1015151 of CERA or equivalent model of makes specified. |
| 87 | S&F in repairs, two way bib tap 15mm dia, with wall flange and aerator screwed down for iron pipe or for brass ferrule complete all as specified and as directed.Make: Cat No. F1015161 of CERA or equivalent model of makes specified. |
| 88 | S&F in repairs towel rail 60 cm long between flanges complete all as specified and as directed.Make: Cat No. F5015103CH of CERA or equivalent model of makes specified. |
| 89 | S&F in repair sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and railing 60cm long complete all as specified and directed by Engr-in-Charge |
| 90 | S&F in repairs, sinks made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 485 mm x 410 mm bowl size 400 mm x 350 mm x 185 mm including CP waste coupling complete all as specified and as directed.Make: Cat No. SBFB 01A of JAYNA or Orra Small of Nirali equivalent model of makes specified. |
| 91 | S&F in repairs, kitchen plate rack of overall size 786mm x914mm x 254mm made out stainless steel sheet not less than 0.63mm thick, design and pattern as approved by GE and fixed to wall with wooden plugs with chromium plated screws and cup washers complete all as specified and as directed.Make: Prayag cat No P-348 or Cat No. SSKPR 315 of Silvershine or equivalent model of makes specified. |
| 92 | S&F in repair bevelled edge looking mirror 5.5mm thick of size 600mm x 450mm mounted on commercial plywood 6 mm thick including PVC beading all round and fixed to wooden plugs with chromium plated screws complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 93 | S&F in repair bevelled edge looking mirror 5.5mm thick of size 600mm x 450mm mounted on commercial plywood 6 mm thick including PVC beading all round and fixed to wooden plugs with chromium plated screws complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Tender Published
Tender notice published.
CompletedCorrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
CompletedCorrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 5 daysBid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysBid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender