Tender For special Repair/Replacement Of Tiling And Misc Works At Kingfisher And Pelican Guest Rooms Of Ancom Under Ge Haddo, Sri Vijaya Puram
Tender Value
48.40 Lakhs
Estimated cost
Bid Submission
19 Nov 2026
18 days left
EMD
96800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair/Replacement Of Tiling And Misc Works At Kingfisher And Pelican Guest Rooms Of Ancom Under Ge Haddo, Sri Vijaya Puram
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided etc, complete all as specified and as directed. |
| 2 | Demolition of (unreinforced) cement concerete in ground floors and paving not exceeding 15 cm thickness (below or above GL) etc, complete all as specified and as directed. |
| 3 | M&L for cement concrete 1:4:8 type D2, using 40mm graded stone aggregate in foundation filling and mass concrete etc, complete all as specified and as directed. |
| 4 | M&L Reinforced cement concrete (nominal mix) A1 1:1.5:3 (20 mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. |
| 5 | M & L for form work to sides and soffits of floor or roof beam and lintels as in flat rough finished surfaces of concrete complete all as specified and as directed. |
| 6 | M&L precast reinforced cement concrete 1:2:4 (type B1) as in cover slab and set in cement morter (1:6), etc complete all as specified and as directed |
| 7 | Material and labour for precast cement concret block masonary 1:3:6 type C1 using 20mm graded stone agg with solid blocks, exc 10cm in width and setting in CM 1:6 etc, complete all as specified and as directed. |
| 8 | Material and labour for Mild steel TMT bars of Fe 500 or Fe 500D, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips etc, complete all as specified and as directed. |
| 9 | Material and labour for Mild steel TMT bars of Fe 500 or Fe 500D, 8 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips etc, complete all as specified and as directed. |
| 10 | M&L for 12mm thick sheet glass toughned glass as in hinged doors, automatic doors closer, stainless steel hand and similar work including cutting to shape, drilling holes required etc, if sheet glass is ground or obscured or frosted, on one side including hacking out old glass panes complete all as specified |
| 11 | M&L for work in 18mm thick HDF Boards with decorative choice lamination on one side and balancing white lamination on other side , fixed with screws/nails as in cupboards, sides of shelves, partitions and in simillar works, etc all as specified and as directed.. |
| 12 | S&F 100mm SS Auto concealed hinges (full overlay) suitable for kitchen cabinets, cub boards, Shelves etc complete all as specified and as directed. |
| 13 | S&F SS Fancy 'D' Type Drawer / Cabinet handles of Size 100mm, etc all as specified and as dierected. |
| 14 | S&F Magnetic catcher with plate, glossy finish for Drawer / Cabinet of Size not less than 50mm, etc all as specified and as dierected. |
| 15 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 16 | M & L for Virified Ceramic tiles light shade 8-10 mm thick (square/ rectangular) polished,(double charged ) area of each tiles exceeding 0.72 sqm but not exceeding 1.00 sqm, in floors set and jointed free tiles in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layers 15 mm thick in cement mortar (1:6) for laying floor finishes all as directed. |
| 17 | M & L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 1 sqm but not exceeding 1.50 sqm, in floors set and jointed free tiles in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layers 15 mm thick in cement mortar (1:6) for laying floor finishes all as directed. |
| 18 | M&L for providing and laying 6 mm thick SPC (Stone Plastic Composite) flooring of WELSPUN make, of approved wooden colour, shade and design, having textured embossed wooden finish surface with grooved/interlocking edges, laid over the existing flooring using suitable adhesive or by click-lock/interlocking system, as recommended by the manufacturer, including preparation and cleaning of the existing floor surface, filling of depressions, uneven portions and gaps with suitable levelling/filling compound wherever required to obtain a smooth, even and level surface, cutting, fitting, jointing, edge finishing, wastage and all necessary materials, tools and tackles required for proper completion of the work, complete all as specified and as directed by the Engineer-in-Charge. |
| 19 | M&L for providing and fixing 6 mm thick SPC (Stone Plastic Composite) wall cladding of WELSPUN make, of approved wooden colour, shade and design, having textured embossed wooden finish surface with grooved/interlocking edges, fixed to the existing vertical surface using suitable adhesive or mechanical fixing/interlocking system, as recommended by the manufacturer, including preparation and cleaning of the existing surface, filling of depressions, uneven portions and gaps with suitable filling/levelling compound wherever required to obtain a smooth, even and plumb surface, cutting, fitting, jointing, edge finishing, wastage and all necessary materials, tools, tackles and accessories required for proper completion of the work, complete all as specified and as directed by the Engineer-in-Charge. |
| 20 | M&L for light shade vitrified ceramic tiles minimum 8-10mm thick (square/ rectangular) polished area of each tiles exceeding 0.72 sqm but not exceeding 1.00 sqm in vertical surfaces such as skirting, dados and riser etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed of cement mortar 1:3 complete all as specified and directed |
| 21 | S&F Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.36 sqm, as in floors etc. set and jointed free in neat cement slurry and pointed in white or colored cement to match including screed bed or bedding layers 15 mm thick in cement mortar (1:6) for laying floor finishes including dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed. complete all as specified and directed. |
| 22 | M&L for providing plain cement concrete 1:4:8 type D-2 (using 40mm graded stone agg) as in sub-base of floor, 100mm thick etc, complete all as specified and as directed. |
| 23 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons, riser of steps, skirting, dado etc laid in any mortar including debris off the premises etc complete all as specified. |
| 24 | M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms,floor, walls and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and polishing including dismantling of existing unserviceable stone tiles alongwith cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed. |
| 25 | Rounding to edges of stone slabs one edge,such as in steps, cooking platform, and other similar situations etc, complete all as specified and directed. |
| 26 | S&F 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 27 | S&F in repairs 75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls etc s complete all as specified and directed. |
| 28 | S&F in repairs 110mm bore UPVC (SWR) bends any radius with access door complete all as specified and directed. |
| 29 | S&F in repairs 75mm bore UPVC (SWR) bends any radius with access door complete all as specified and directed. |
| 30 | Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed |
| 31 | M&L for 10mm thick plaster in CM 1:6 on fair face of concrete surface or brick walls finished even and smooth without using extra cement complete all as specified |
| 32 | M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry of concrete surfaces finished even and smooth without using extra cement etc, complete all as specified and as directed.Note: Water proofing compound shall be measured and paid separately. |
| 33 | Supplied only integral waterproofing compound etc, complete all as specified and as directed. |
| 34 | Material and labour for preparation of new wall surfaces and applying two coats of Royal Emulsion (white or tinted) over a coat of 2 mm thick wall putty over a coat of alkali resistance primer complete all as specified. |
| 35 | Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc, complete all as specified and as directed. |
| 36 | Material & Labour for complete removal of existing treatment on old walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc, complete all as specified and as directed. |
| 37 | Material and labour for Complete removal of existing treatment on wall with wire brush ,scrapping down smoke soot ,mould , moss and efflorescent salts ,trading oil and greasy spots ,filling holes ,cracks with cement base putty and applying two coats of Royal Emusion over a coat of primer and a layer of 2 mm thick wall care putty including preparation of old decorated surfaces of wall complete all as specified and as directed. |
| 38 | S&F in repairs vitreous china wash down water closet (Rimless Wall Hung WC), size 390x570x365 mm, complete with UF soft close seat cover, concealed cistern body, flush plate, inlet & outlet connection, fixing bolts, brackets and all other connected accessories, fixed to wall in approved manner and making good disturbed surfaces complete all as specified and directed. Make : Jaquar Cat No : VGS-WHT-81953UF or equivalent |
| 39 | S&F in repair vitreous china table top wash hand basin Square shape of size 530x420mmx140mm including , 32 mm CP waste coupling, waste fittings all necessary inlet and out let connections complete all as specified Make : Jaquar (Cat Part No : JDS WHT 25907N) or equivalent |
| 40 | S&F in repair wash hand basin mixer, 15 mm dia, cast copper alloy, chromium plated, fancy type, with single lever handle, long shank, screwed both ends for connection to pipe/unions, complete with nuts, washers and all other fixing accessories, complete all as specified and as directed. Make : Jaquar Cat Part No : OPP-BLM-15005BPM or equivalent |
| 41 | S&F in repair towel rack and lower hanger, brass, chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repairs complete all as specified and as directed Make : Jaquar (Cat part No AQN-BLM-7781B) or equivalent |
| 42 | S&F in repair CP brass hot and cold 15mm dia wall mixture 3-in-1 system with provision for both hand shower and overhead shower complete with 115mm long bend pipe, connecting leg and wall flange complete all as directed. Make : Jaquar Cat Part No : Jaquar Cat part No OPP-BLM-15125PM or equivalent |
| 43 | S&F in repair Toilet paper holder Make :Jaquar Code ACN-BLM-1153S or equivalent |
| 44 | S&F in repair towel ring round Make Jaquar ACN-BLM-7721BN or equivalent |
| 45 | S&F in repair tubular towel rail, brass, chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repairs complete all as specified and as directed Make : Jaquar Cat part No AQN-BLM-7711B or equivalent |
| 46 | S&F CP corner glass shelf with bracket complete all as specified. Make : Jaguar Cat Part No - CAN-1173 or equivalent |
| 47 | S&F chromium plated soap dish of size 120x80mm, fixed to plugs with chromium plated brass screws complete all as specified Make : Jaquar Cat part No AQN-BCH-7731 or equivalent |
| 48 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed Make : Jaquar Cat part No ALD-BLM-565 or equivalent |
| 49 | S&F in repair bib tap, brass, 15mm dia, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and as directed Make : Jaquar Cat part No OPP-BLM-15037PM or equivalent |
| 50 | S&F in repair angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for unions complete all as specified and as directed. Make : Jaquar Cat part No OPP-BLM-15053PM or equivalent |
| 51 | S&F for Two way Bib Cock Jaquar Code : ORP-BLM-10041PM techno commercially equivalent in PS makes |
| 52 | S & F Hand Shower ø100mm Round Shape/ Rectangular shape Single Flow (ABS Body with Matt finish) with Rubit Cleaning System (Jaquar Code : Jaquar Cat part No HSH BLM-1707 or equivalent |
| 53 | S&F Overhead Shower 120mm dia Round Shape Single Flow (ABS Body in Matt finish) alongwith shower Arm with Rubit Cleaning System etc., complete all as specified and directed. Make :Jaquar Cat part No OHS-BLM-1637 or equivalent |
| 54 | S&F in repair for PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer etc., complete all as specified and directed. |
| 55 | S & F bevelled edge mirror of size 850 x 600 mm selected quality glass fancy type as approved by Engr-in-Charge |
| 56 | Supply and fixing of UPVC/ fibre false ceiling of panel (not less than 1 mm thickness) sizes of 340mmx 2700mm/ 300mm x 2500mm, exterior grade durable and resistant to moisture, water and borer-fungus-termite attack. Panels to be installed with GI / Aluminium sections of suitable gauge & size according to site conditions . Panels fixed using with suitable trims for edge profiles and for Connecting profiles . Panels must be maintenance free , rust proof and are 100% Water proof complete all as specified and sample kept in the office of the Engr - in - Charge. Note : Colour and pattern of false ceiling boards to be approved by GE. |
| 57 | S&F for GI frame work of seamless ceiling/ UPVC false ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flange of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm c/c intermediate channel 0.9mm thick having two equal flanges of 15mm suspended from soffit at approx 900mm c/c with GI cleats and steel expansion fasteners with and incl ceiling section ( not exc 1.2m length) of 0.55mm thick having kurled web of 50mm an flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting across the intermediate channel at 457mm c/c incl hangers 6mm dia GI adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed |
| 58 | M & L for Non-Skid heavy duty ceramic tiles of size 600 X 600 X 10mm thick, or high dimension (except thickness) of any colour any design Durastone, weather proof impact resistant, abrasion resistant exterior tiles, as in floors vertical cladding and etc , set and jointed in neat cement slurry over and pointed in white or coloured cement to match, over 15mm thick screed bed in CM (1:4) complete all as specified and as directed. |
| 59 | Cutting chases in stone, concrete block or slab walls, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth |
| 60 | S&F 20mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including suitable reducer for 15mm dia taps fitting as required complete all as specified |
| 61 | S&F 25mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including suitable reducer for 15mm dia taps fitting as required complete all as specified |
| 62 | Providing and fixing stainless steel linear floor drain grating of size 300 mm × 100 mm (12 inch × 4 inch) made of SS 304 grade stainless steel, complete with removable top grating, frame, anti-cockroach/anti-odour trap arrangement, outlet connection, and all fixing accessories, including embedding in floor, cutting/chasing, and making good the damaged portion complete, all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysNov 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender