Tender For Special Repair To Bldg No P-49 And P-66 In Albert Ekka Vihar (Fafa) At Morar Cantt Under Ge Gwalior
Tender Value
1.31 Crore
Estimated cost
Bid Submission
02 Dec 2026
10 days left
EMD
2.06 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gwalior → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No P-49 And P-66 In Albert Ekka Vihar (Fafa) At Morar Cantt Under Ge Gwalior
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete of any description and in any position (un-reinforced) in ground floors and paving not exceeding 15cm thick (below or above GL) and removing of rubbish from site complete all as specified and directed. Note: Demolished material through out of MoD Land rate included above item. |
| 2 | Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) including removing of rubbish from site complete all as specified and directed. |
| 3 | Dismantiling of stone slabs and tiles of any description or any thickness in floors, aprons, skirting, dado etc. laid bedded and pointed in any mortar complete all as specified and directed. |
| 4 | M&L for non skid ceramic tiles, joint free, coloured tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set over and including 15 mm thick cement screed in (1:6) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed. |
| 5 | M&L for non skid ceramic tiles, joint free, coloured tiles 7mm to 8 mm mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:4) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.with the colour of tiles complete all as specified and directed. Colour and design of tiles as approved by GE. |
| 6 | M&L for joint free non skid ceramic coloured tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and including 15 mm thick cement screed in (1:6) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed. Colour and design of tiles as approved by GE. |
| 7 | M&L for 25mm thick PCC (1:2:4) Type B-0 using 12.5 mm graded stone aggregate as levelling course finish even and fair complete all as specified & directed. |
| 8 | M&L for digital glazed cearmic tiles, coloured tiles 450x300x 7 to 8 mm thick, designer pattern tiles, on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick rendering or backing coat in cement mortar (1:4) complete all as specified and directed. Colour and design of tiles as approved by GE. |
| 9 | M&L for machine cut Kota stone slab flooring 20-25 mm thick size of stone 550 x 550 mm over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing, over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:6 ) complete all as specified and directed. |
| 10 | M&L for machine cut kota stone slab 20 - 25 mm thick as in riser / steps, skirting, dado,cills and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed. |
| 11 | M&L for Granite stone slab 16 to 18 mm thick machine cut, bedded and joined with cement and pointed with white cement (1:2) using marble dust with admixture of pigment to match over and including 20 mm thick screed bed CM (1:6) the shade of granite stone including cutting and polishing type as in cill and jamb/skirting, steps cooking plateforms includigng rounding off the exposed edges and polishing all as specified and directed. Colour and design of Granite as approved by GE. |
| 12 | M&L for RCC (1:2:4) type B-1 (nominal mix) (using 20mm graded stone aggregate) as in shelves, etc complete all as specified and directed. |
| 13 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) any description and in any position not otherwise specifically provided for complete all as specified and directed. Note: Demolished material through out of MoD Land rate included above item. |
| 14 | Demolition of brick work /stone work built in cement mortar including all quoins, arches, pillars etc including removal of rubbish from site complete all as specified and as directed. |
| 15 | M&L for Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).complete all as specified and as directed. |
| 16 | M&L for PCC type B-1 (1:2:4) using 20mm graded stone aggregate as in coping, as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, staging, slightly rounded or chamfered on edges, angles, kerbs and throating in roof as directed complete all as specified and directed. |
| 17 | M&L for Plain cement Concrete type B-0 1:2:4 ( 12.5 mm graded stone aggregate) 40 mm thick average as in roof padding/ levelling finish even and smooth etc complete all as specified & directed. |
| 18 | M & L for applying Smartcare Damp proof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @2.0 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof: water) and other coats to be applied undiluted. (ii) The undiluted 2nd & 3rd coatings needs to be reinforced with 40 GSM geotextile to be sandwiched between them. (iii) After that final 4th coating shall be applied. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of GE.Make: SmartCare Damp Proof of Asian Paints or equivalent in Berger and Nerolac.Notes:-(a) The work shall be executed through authorised applicator of manufacturer only.(b) Authrised Applicator shall be approved by GE before starting of work.(c) All materials shall be procured directly form manufacturer.(d) The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Eight years in favour of GE. |
| 19 | M &L For applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS -3384 @ 0.3 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms /sqm ) land on primed surface by torch application complete all as specified and as directed. |
| 20 | M&L for Providing cement concrete type B1 1:2:4 using 20 mm graded aggregate as in roof kerbs or mud stops, rounded or chamfered on edges or water tank staging, coping etc finished even and smooth complete all as specified and directed. |
| 21 | M&L precast cement concrete tiles of size 250mmx250mmx20mm, machine pressed as in roof/floor top , comfirming to IS -1237-1980 laid over 15mm thick screed bed in CM 1:4 and set, jointed and pointed in Epoxy resin in roof floors and cut and polished, with white cement and pigment with cement mortar (1:2) by mixing of chemical or equivalent complete all as specifeid and as directed by GE. |
| 22 | M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4).complete all as specified and as directed. |
| 23 | Demolition of concrete (un-reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. Note: Demolished material removed through out of MoD Land rate included above item. |
| 24 | M&L for Priming surfaces and applying normal treatment (for moderate conditions) using glass fibre base bitumen felt, grade 2 in sunken floor surfaces complete all as specified & directed. |
| 25 | M&L for 20 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surface and mixed with WPC finished even and smooth without using extra cement complete all as specified & directed. |
| 26 | Supply only liquid water proofing compound @ 200ml per 50 kg bag of cement. Make: Sika, Pidilite, Fosroc |
| 27 | M&L for applying two coats of two component flexible acrylic polymers modified cement based waterproof coating in sunken floors and wall joints having good compressive strength and shrikage resistance etc of Make : Dr. Fixit Pidifin 2K all as per manufacturer instructions in product brouchure equivalent in Fosroc, Sika etc complete all as specified & directed. |
| 28 | M&L for PCC type E2 (1:5:10) with 40mm brick aggregate as in filling of sunken floors complete all as specified and directed. |
| 29 | Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square metre each complete all as specified and as directed. |
| 30 | Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 sqm and not exc 4.00 sqm each complete all as specified and as directed. |
| 31 | S&F Pressed steel frames 105x60mmfor doors with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete, as specified, supplied and fixed. |
| 32 | S&F Pressed steel frames 125x60mmfor doors with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete, as specified, supplied and fixed. |
| 33 | M&L for PCC 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) for filling in hollow section of pressed steel frames and like complete all as specified and directed. |
| 34 | S&F 30 mm thick Flush door shutters ,soild core construction ,with paticle board core and plywood face panels , commercial type both face is covered with decorative face veneer with lipping /frame to match and complete all as specified and directed. |
| 35 | M & L for 35 mm thick glazed and skeleton factory made door shutters of 2nd class Hard Wood, open rebated and prepare to receive glass, guage etc (without sash bars) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified complete all as specified and directed. |
| 36 | S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete allas specified and directed. |
| 37 | M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. |
| 38 | M&L preperation of new wooden surface and applying two coat of synthetic enamel paint over a coat of pink primer on new wooden surface any description not otherwise described over 10 cm width or girth and complete all as specified and directed. |
| 39 | M&L for Factory made single extruded WPC ( Wood polymer Composite) solid door/ window/ Ceosetory windows & Frames/ Chowkhat of size 45x85 mm comprising of virgine PVC polymer of K value 58-60 ( Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strenght of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold/ fast/lugs/SS dash Fasterners of required dia and lenght complete as per direction. |
| 40 | S&F for factory made single extruded WPC (Wood polymer composite) solid deccrative type Flush door shuuter of size 30mm thick comprising of virgine polymer of K value 5868 ( Suspension Grade), calcium carbonate and natural fiber( wood powder/ rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 of 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strenght of 1800 N ( Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant. WPC to be laminaed with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with 100mm long stainless steel butt hinges 04 Nos with necessary full body threaded star headed counter sunk s.s screws,complete all as per specified and directed |
| 41 | S&F of 100 mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, medium weight complete all as specified and directed. |
| 42 | S&F of Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 43 | S&F of 200mm long aluminium anodised, barrel tower bolt of extruded section and fixed complete all as specified and directed. |
| 44 | S&F of 150 mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 45 | S&F of Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 46 | S&F of 150 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed |
| 47 | S&F for in repair Curtain rod stainless steel decorative type 25 mm dia including fixing bracket and end knobs complete all as specified, complete all as specified and directed. |
| 48 | M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 49 | M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator (adequate track) without sash, aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware ie. handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc. complete all as specified and directed Note : Panel filling ie. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately. |
| 50 | S&F 4.8 mm thick tinted glass of selected quality in square not exceeding 0.5 sqm in each pane, fixed to aluminum frame with and including suitable rubber beading complete all as specified and directed |
| 51 | Taking down cement or cement lime plaster on wall/ceiling/roof on brick/concrete/stone walls etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed. Note: Demolished material through out of MoD Land rate included above item. |
| 52 | M&L for 10 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 53 | M&L for 15mm thick cement plaster with ready mix plaster (as per manufacturers instruction) on brickwork and concrete surfaces finished even and smooth (without using extra cement) complete all as specified and directed. |
| 54 | M&L for 5-10 mm thick rendering with ready mix plaster (as per manufacturers instruction) on ceiling, chajja, roof projection and facia surface finished even and smooth (without using extra cement) complete all as specified and directed. |
| 55 | M&L washed stone grit plaster on exterior walls in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15 mm cement 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size) in pannels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings, complete all as specified ( Payment for providing grooves shall be made separately). |
| 56 | M&L forming groove of uniform size 15 mm wide and 15 mm deep in top layer of washed stone grit plaster as per approved pattern using wooden battens nailed to the under layer including removal of wooden battens , repair to the edges of panels and finishing the grooves complete etc |
| 57 | M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper, over and incl a layer of 2mm thick wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed. |
| 58 | M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 59 | M & L for preparation of new plaster surfaces of wall and for applying Two or more coats of 100% Premium acrylic exterier emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including ver a coat of exterior wall care putty on wall complete all as specified and directed. |
| 60 | M&L complete removal of exiting treatment from external wall preparation of old plastered surface and applying two coat of premium acrylic exterior anti algal fungal emulsion paint with silicon additives @ 1.43litre/ 10 Sqm over one coat of weather coat exterier primer over a coat of exterior wall care putty on wall all as direced. |
| 61 | M&L for complete removal of existing treatment of plastered or unplastered surfaces walls and applying two coat of oil bound distemper (acrylic) over a coat of 2mm thick wall care putty on walls complete all as specified and directed. |
| 62 | M&L for complete removal of existing treatment of plastered or unplastered surfaces of ceiling and applying two coat of white wash complete all as specified and directed. |
| 63 | Dismantling boarding any description fixed with nails in any position (including cup board/ wardrobe shutters/shelves upto 25mm thick) complete. |
| 64 | M & L for 18-19 mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work with decorative face veneer on both faces complete all as specified. |
| 65 | M & L for 12 mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work with decorative face veneer on both faces complete all as specified. |
| 66 | S&F of modular soft auto closed SS hinges of any degree opening, complete as specified and as directed by Engr-in-Charge. |
| 67 | S&F of modular stainless steel handle 200mm complete all as specified and directed. Make : Godrej/ Sleek/ Hettich/Ebco |
| 68 | S&F of modular stainless steel handle 150mm complete all as specified and directed. Make : Godrej/ Sleek/ Hettich/ Ebco |
| 69 | S&F for magnate catcher of metal body and striking plate heavy duty includind fixed with screw, complete all as specified and directed. |
| 70 | S&F 15x20x4 Inch stainless steel kitchen basket with stainless steel wire perforate plate fabricated and stainless steel telescopic drawer chanel with ball bearing soundless complete all as specified and directed. |
| 71 | Taking up or down steel tubing and connections including cleaning for refixing or removing to store of 15mm bore of pipe, complete all as specified. |
| 72 | Taking up or down steel tubing and connections including cleaning for refixing or removing to store of 20mm bore of pipe, complete all as specified. |
| 73 | Taking up or down steel tubing and connections including cleaning for refixing or removing to store of 25mm bore of pipe, complete all as specified. |
| 74 | Supply and laying of 20mm dia of bore CPVC pipe SDR-11 and plain CPVC SDR-11 fittings (ISI) marked, concealed or fixed to wall or laid in floors complete all as specified. |
| 75 | Supply and laying of 25mm dia of bore CPVC pipe SDR-11 and plain CPVC SDR-11 fittings (ISI) marked, concealed or fixed to wall or laid in floors complete all as specified. |
| 76 | S&F of Rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) 500 litres capacity, triple layer in construction white in colour hoisted and fixed in position including taking out old any type size complete all as specified and as directed. |
| 77 | S&F for 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed in 20mm dia pipe. (Minimum weight 15mm-142gms, 20mm-210gms, 25mm-455gms, 40mm-690gms) complete all as specified and directed. |
| 78 | S&F in repairs for gun metal globe/gate valve with iron wheel head screwed both ends for iron pipe of 20mm bore complete all as specified and directed. |
| 79 | S&F in repairs for vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps and connection to trap and to flushing pipe to complete and making good to floor, complete all as specified and directed. |
| 80 | S&F in repair for PVC valveless syphonic action type flushing cistern low level white with inlet ball valve, float end handle handle including bracket complete of capacity 10 litres, complete all as specified and directed. |
| 81 | S&F in repair flush pipe fixed to pedestal pan, incl all joints, of polythylene of low or high denisity or PVC 32 mm dia for low level cistern complete |
| 82 | S&F for in repairs 15mm angle cock chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified . |
| 83 | S&F in repairs for shower rose brass chromium plated without swivel joints, 100 mm in size including fixing to steel pipe complete all as specified and directed fixed in repairs, complete all as specified and directed. |
| 84 | S&F for in repairs 600x450 mm looking mirror of selected quality glass mounted on 4mm thick PVC building board or commercial plywood and fixed to wooden plug with chromiun plated screws complete all as specified and directed |
| 85 | S&F for in repairs of vitreous china wash basin, white, flat back, size 550 x 400mm excluding taps, waste, chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets complete all as specified and directed. |
| 86 | S&F in repairs Brass CP WHB mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified. |
| 87 | S&F for in repairs waste coupling fittings, brass chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly nuts, flange end bedded in red lead cement and other fixed 32 mm dia bore complete all as specified. |
| 88 | S&F for in repairs waste coupling fittings, brass chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly nuts, flange end bedded in red lead cement and other fixed 40 mm dia bore complete all as specified. |
| 89 | S&F in repairs 32mm dia ribbed PVC waste drain pipe for WHB, urinal etc, strached length 90cm with PVC coupling socket complete all as specified and directed |
| 90 | S&F in repair for 15mm dia PVC connection with PTMT nuts of length 600 mm, heavy duty, steel wire mesh coated complete all as specified and directed. |
| 91 | S&F for in repairs stainless steel Chromium plated grating 100 mm dia, fixed in repairs to Nahani traps, with/without hole complete all as specified and directed. |
| 92 | S&F for in repairs for 15mm, bib tap Fancy type long body chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe complete all as specified |
| 93 | S&F for in reairs PVC bath room cabinet mirror of Size 500mmx400 mm make Prayag Cat No 556 or euivelent in other makecomplete all as specified and directed.by Engineer in charge. |
| 94 | S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick glass shelf 12cm wide with chromium plated bracket and guard and railing 60cm long completed all as specified and directed |
| 95 | S&F in repairs corner glass shelf 300mm (with ABS Bracket ) complete all as specified and directed. |
| 96 | S&F in repairs Soap dish of CP fixed with pvc rawal plugs and screw, complete all as specified and directed. |
| 97 | S&F in repair brass cromium plated tubular towel rail D type 20mm dia and 60cm long complete all as specified and directed. |
| 98 | S&F in repairs for wall mixer with Three in one pattern in of brass CP, 15mm dia complete all as specified and directed. |
| 99 | S&F in repair plate rack of size 900mmx750mm made out of 1mm thick stainless steel sheet of 304 grade of wire type / sheet pattern (weight not less than 7 Kg each) size and type as directed and approved by GE fixed to wall with necessary SS screws/plugs/brackets etc fitting arrangement Complete all as specified and directed. |
| 100 | S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 101 | S&F in repairs Brass CP Single lever Sink mixer, 15mm bore with swinging sprout on upper side with connecting Legs & Wall Flangers screwed down for 15mm bore iron pipe complete all as specified. |
| 102 | Taking down eaves gutters and rain water pipes (any size 75mm to 110mm of any pattern) of any description and in any position including all fittings, heads, shoes, bend, swan necks etc (measured overall as fixed along the centre line over fittings and accessories) complete all as specified |
| 103 | S&F for 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified |
| 104 | S&F for 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified |
| 105 | S&F for 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified |
| 106 | S&F for 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified |
| 107 | S&F for 110mm dia PVC (SWR) pipe bends any radious complete all as specified and directed. |
| 108 | S&F for 75mm dia PVC (SWR) pipe bends any radious complete all as specified and directed. |
| 109 | S&F for 110mm dia PVC (SWR) pipes junction single (single T/Y) equal or unequal any radious with access door complete all as specified. |
| 110 | S&F for 75mm dia PVC (SWR) pipes junction single (single T/Y) equal or unequal any radious with access door complete all as specified. |
| 111 | S&F for SWR bends 75mm provided with access door complete all as specified. |
| 112 | S&F for 110mm dia PVC (SWR) vent cowl complete all as specified. |
| 113 | S&F Stack clamps made out of 50 mm by 5 mm flat iron and 16 mm dia around iron stays including bolt and nuts for securing ends of stays to walls or roofs, bore pipe 100/110 mm dia pipe complete all as directed. |
| 114 | S&F Stack clamps made out of 50 mm by 5 mm flat iron and 16 mm dia around iron stays including bolt and nuts for securing ends of stays to walls or roofs, bore pipe 75 mm dia pipe complete all as directed. |
| 115 | M&L for PVC (SWR) gully trap 125 /100 plain with grating incl. jointing with solvent cement as in repair, complete all as specified and directed. |
| 116 | M&L for reinforced cement concrete Design mix M-20 ( using 20 mm graded stone aggregate ) as in chajja/fascia/balcony slab like etc. complete all as specified and directed. |
| 117 | M&L use and waste formwork to chullah hoods, chajjas, troughs and similar items including edges of concrete rough finished surfaces of concrete complete all as specified and directed |
| 118 | M&L for mild steel TMT bars, 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed. |
| 119 | M&L for 75mm thick PCC (1:3:6) Type C2 using 40mm graded stone aggregate as in plinth protection/hard standing and floor finishes surface even and fair without using extra cement complete all as specified and as diected |
| 120 | M&L for Forming Construction joint 30mm deepx10mm wide filled with sealing compound grade A complete all as specified and as diected. |
| 121 | S&F, in repair, bottle trap of PTMT having minimum water seal of 25mm ( Minimum weight 32 mm -260gms ) complete all as specified and directed. |
| 122 | Excavation in post holes (or similar holes) each n. exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n. exc 50m and making good surface in soft/loose soil. |
| 123 | M&L PCC 1:4:8 Type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed. |
| 124 | S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161 1979 complete all as specified and directed. |
| 125 | S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 126 | M&L for Hard core of stone aggregate gauge n exc. 63 mm deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 127 | M & L for PCC (1:3:6) Type C-2 (40mm graded stone aggregate), 75 mm thick as floor surfaces concrete complete all as specified and directed. |
| 128 | M&L for machine made ,1st quality, precast cement concrete rubber moulded coloured interlocking paver blocks / tiles , 60mm thick of grade M-35, of any shape or shap and designe as approved, with colour pigment , laid over and including 50 mm thick (average) sand cusion fixed as in floors/ paths/ pavings etc, complete all as specified and directed.Note : Sand Cusion shall be measured and paid in separate item. |
| 129 | M&L for providing and laying at near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not more than 5 mm), including making drainage opening wherever required complete. |
| 130 | M&L for preparation for new cement concrete, brick curve stone, asbestos cement for surfaces and applying two coat of synthetic enamel paint any description or plain or moulded, over 10 cm width or girth when unconnected with other painting or when painted in a different tint complete all as specified and directed. |
| 131 | Excavating in trenches n exc 1.5 m wide and n. exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil including sewage pipe and bed any type and dia complete all as specified and as directed. (Note: As in foul condition manualy excavation works). |
| 132 | M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 150mm bore of pipe complete all as specified and directed. |
| 133 | S&F for 150mm bore reinforced concrete pipe class NP2, laid and jointed complete with collars complete all as specified and directed. |
| 134 | Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed. |
| 135 | M&L Cutting holes in brick/ stone wall, depth of embedment portion of hold fast exc half brick wall but not exc one brick wall, built in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed |
| 136 | Removing excavated material nexc 50m and depositing where directed at a level nexc 1.5Km above the starting point with soil complete. |
| 137 | M&L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in cover slabs for man holes/ drain covers like etc and set in CM 1:4 including necessary form work all as specified. Note Rienforcement and form work shall be measured paid separately) |
| 138 | M&L for mild steel TMT bars, 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed. |
| 139 | M&L Hand rails, half round or other stock section or core for wooden hand rail straight portion , drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing post including cutting tops to shape as directed, drilling holes, notching for wire , etc.; flat iron fillets ( for securing wire mesh etc. including all necessary drilling , bolting or rivetting , etc., and similar work conforming to Fe 290 Gde E 165 with and including applying two coats of synthetic enamel paint over a coat of primer alround before fixing in position complete all as specified and directed |
| 140 | M&L use and waste formwork to chullah hoods, chajjas, troughs and similar items including edges of concrete rough finished surfaces of concrete complete all as specified and directed Please Enable Macros to View BoQ information |
| 141 | M&L use and waste formwork to chullah hoods, chajjas, troughs and similar items including edges of concrete rough finished surfaces of concrete complete all as specified and directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysDec 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender