Defence Statutory Bodies & Commissions/Committees Closing in 10 days TDR #58297989

Tender For Special Repairs To Bldg No. P-134 At Dacca Colony At Masimpur Mil Stn

Issued by Statutory Bodies & Commissions/Committees · Cachar, Assam
Tender Value
78.17 Lakhs
Estimated cost
Bid Submission
27 Nov 2026
10 days left
EMD
1.42 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Cachar → Assam
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender For Special Repairs To Bldg No. P-134 At Dacca Colony At Masimpur Mil Stn

BOQ

Name of Work:- SPL REPAIRS TO BLDG NO. P-134 AT DACCA COLONY AT MASIMPUR MIL STN
Sl. No. Item Description
1Dismantling of AC sheet corrugated /semi corrugated sheets in roofing any gauge and any thickness including ridge, valley/gutter etc. complete all as specified and directed.
2Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based corrugated / semi corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws with rubber washer as per manufacturer instruction complete all as specified and as directed.
3Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws with washer as per manufacturer instruction complete all as specified and as directed.
4Material and labour preparation of old steel surfaces of any description over 10 cm width or girth applying one coat of synthetic enamel paint complete all as specified and as directed.
5Supply and fixing steel work in tubular trusses i.e truss bottom, top bend, sides, side supports, holding plates, posts and base plate etc. including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 etc complete all as specified and as directed .
6Supply and fixing in repair Rotational Moulded Polythene [HDPE] Water Tanks, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 20mm/15mm dia spouts for connecting inlet, outlet, over flow and washout pipes, Ball Valves, 25 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe [Minimum Weight 25mm - 455 Grams] etc. complete all as specified and as directed.
7Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.
8Material and labour for 40 mm thick PCC (1:2:4) type B0 using 12.5 mm graded stone aggregate as levelling course on roof top or similar work finished fair & even complete all as specified and as directed.
9M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 KG of cement per Sq.m area, rendering 10mm thick in cement mortar 1:4 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound @ 3% by weight of cement of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, applying one coat of hot paving bitumen of penetration value 85/25 conforming to IS 73 @ 1.20 kg/sqm over a coat of bitumenous primer @ 0.40 ltrs per sqm and applying a layers of APP based polymeric membrane, 3mm thick (minimum) weight 3.50 Kg/sqm reinforced with polyster non woven fabric (weighing not less than 100 gms/sqm) shall be applied over Bitumenious primer (Application of polymeric memberane shall be by torch application, over laps shall be minimum 75mm in the transverse direction & 100 mm in the longtudinal direction) polymeric membrane shall be taken to a depth of 65 cm (minimum) and then inserted inside the groove of parapet wall ( Cont..)
10and shall be finished by membrane flashing, coved fillet in PCC (1:2:4) type B-0 of radius 75 mm shall be provided at the junction of roof & other vertical surfaces & surfaces shall be painted with hot paving bitumen of penetration value 85/25 conforming to IS 73 @ 1.20 kg/sqm & applying one coat of aluminium paint over the APP modified membrane @ 0.11 kg/sqm including taking down existing Roof Treatment of any description and removing rubbish to a distance not exceeding 50 M complete all as specified and as directed. Note: (i) Water proofing compound will be measured and paid separately.
11Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and as directed.
12Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing unserviceable tiles and rubbish off the premises complete all as specified and as directed.
13Material and labour for 25mm thick PCC (1:2:4) type B0 (using 12.50mm graded stone aggregate) as floor finished even and rough to receive the top layer complete all as specified and as directed.
14Material & Labour for 75mm thick, PCC 1:3:6, Type C-2, using 40mm graded aggregate as in Plinth protection etc surface finished even and fair without using extra cement and providing necessary joints 12mm wide to the full depth of PCC at every 3 meters and every change of directions and the joints duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade any penetration and 3 parts of sand [all by weight] complete all as specified and as directed.
15Material & Labour for joint free non skid ceramic coloured tiles 7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.06 sqm but not exc 0.11sqm in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match including screed bed of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by AGE(I)/GE.
16Material & Labour for joint free non skid ceramic coloured tiles 7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.18 sqm but not exc 0.36sqm in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match including screed bed of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by AGE(I)/GE.
17Material & Labour for joint free non skid ceramic coloured tiles 7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.18 sqm but not exc 0.36sqm as in skirting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over and including rendering of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by AGE(I)/GE.
18Material & Labour for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, light shade, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.
19Material & Labour for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, light shade, area of each tiles not exceeding 0.36 sqm, as on skirting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over and including rendering of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.
20Material and labour coloured Glazed ceramic tiles of size 300 X 450 X 7mm thick of premium quality as in skirting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over and including rendering of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by AGE(I)/GE.
21Material and labour 18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 20 mm thick screed in cm (1:4) complete all as specified and as directed. Note: The colour / shade / design of granite shall be as approved by AGE(I)/GE.
22Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.
23M & L for reinforced cement concrete 1:1.5:3 (using 20 mm graded aggregate) as in Slabs supported on walls, beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.
24Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat rough finished surface of concrete complete all as specified and as directed.
25Use and waste formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide rough finished surface of concrete complete all as specified and as directed.
26Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed.
27Diamantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and as directed.
28Material & Labour for machine cut Kota stone slab flooring using 20 to 25mm thick slabs, laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including diagonals, inlays, borders, margins in two or more shades of slabs including screed bed of mortar 20 mm thick in Cement Mortar 1:3 complete all as specified and as directed.
29Material & Labour for machine cut kota stone slab as in riser of steps, skirting, dado etc. using 20 to 25mm thick slabs laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including borders, margins in two or more shades of slabs over and including rendering of 10mm thick in cement mortar 1:3 complete all as specified and as directed.
30Material and labour for 100mm thick Plain Cement concrete type B-2, P.C.C 1:2:4 (20mm graded aggregate) as in base of flooring including wearproof topping as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings, and finished even and smooth (except metallic hardner) complete all as specified and directed.Note:- Mettalic floor hardner will be measured and paid seperately.
31Supply only Mettalic floor hardner complete all as specified and as directed.
32Material & Labour glass dividing strips, 3mm thick, 38mm wide inserted in position, conform to design, fixed in floors complete all as specified and as directed.
33Dismantling wall and ceiling boards (AC, fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets complete all as specified and as directed.
34Material and labour for suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system) of grid size 600mmx600mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 8mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre in a grid of GI systtem duly suspended with 4 mm dia GI bar hanger fixed with steel dash fasteners or iron purline from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinkler, smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. The last hanger at the end of each main runner should not be interlocked between main runners @ 610mm c/c, as to form 600 mm x 600 mm grid complete all as specified and as directed.
35Taking down chowkat with shutter without taking off shutter from the frame n.exc 1.50 Sqm each complete all as specified and as directed.
36Taking down chowkat with shutter without taking off shutter from the frame exc 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and as directed.
37S & F Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one or more rebates including hinges (100/50mm stainless steel),lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.
38S & F Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one or more rebates including hinges (100/50mm stainless steel),lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.
39Material and labour Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in back filling of steel frame, holdfast including necessary form work complete all as specified as directed.
40Supply & Fixing factory made, 35mm thick, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [a] and fitted to Chowkats complete all as specified and as directed.
41Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed.(ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid separately.
42Supply and fixing Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed. Note: stainless steel butt hinges and necessary S.S screws shall be measured and paid separately.
43Supply and fixing Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed. Note: stainless steel butt hinges and necessary S.S screws shall be measured and paid separately.
44Supply and fixing 18/19 mm thick interior grade block board, grade 2 quality, decorative type with decorative face veneer on one face fixed with screws to timber frame work complete all as specified and as directed..
45Supply and fixing continious (Piano) hinges, mild steel, bright finish or electro galvanised of 30mm width (when open) complete all as specified and as directed.
46Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.
47Supply and fixing of Framed work such as grills, gratings, etc.. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe 290 Gde-E-165 complete all as specified and as directed.
48Supply and fixing factory made uPVC white colourCasement door with top hung ventilator with 3D andSS friction (400 x 19 x 1.9 mm) made of (big series)frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 + 0.2 mmand single glazing bead / double glazing bead ofappropriate dimension. (Area of door upto 2.50 sqm)comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels alongwith zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc.Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in-Charge.Note: For uPVC frame, sash and mullion extrudedprofiles minus 5% tolerance in dimension i.e. indepth & width of profile shall be acceptable.Variation in profile dimension in higher side shallbe accepted but no extra payment on this accountshall be made..
49Note: (i) For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.(ii) Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.(iii) The unit rate quoted by contractor excludes cost of glass, SS wire mesh and includes all other connected accessories.
50Supply and fixing factory made uPVC white colour casement door with top hung ventilator with 3D and SS friction (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 + 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension,EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels alongwith zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in-Charge.
51Supply only 4 mm thick Sheet glass, ordinary quality in square n exc 0.5 sq. m in each pane complete all as specified and as directed.
52Supply only 4 mm thick frosted glass, ordinary quality in square n exc 0.5 sq. m in each pane complete all as specified and as directed.
53Supply only Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and as directed.
54Supply and fix Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples complete all as specified and as directed.
55Supply and fixing stainless steel butt hinge, 100mm long, medium weight, cold rolled fixed with steel screws or welded to steel frame where required complete all as specified and as directed.
56Supply and fixing Floor Door Stopper of size 140 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.
57Supply and fixing Mild Steel Door Spring 300 mm, Ordinary Rat Rail Rod Pattern springs including roller and roller plate complete all as specified and as directed.
58Supply and fixing 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts,of extruded sections or cast aluminium alloy complete all as specified and as directed.
59Supply and fixing aluminium anodized, barrel tower bolts, 200mm long of extruded section complete all as specified and as directed.
60Supply and fixing aluminium handles, fabricated type, anodised 125 mm long fixed with screws complete all as specified and as directed.
61Supply and fixing in repairs minimum 1 mm thick SS chromium plated Curtain Rod of 20 mm dia including PVC rings @ 100 mm centre to centre, fancy type side brackets end knobs of size suitable to 20mm dia curtain rod fixing SS screws and rawl plugs complete all as specified and as directed.
62Material and labour for preparation of new steel surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed..
63Material and labour for preparation of new wooden surface exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.
64Supply and fixing 20 mm outer dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, including taking down of unserviceable GI tubing complete all as specified and as directed.
65Supply and fixing 20 mm outer dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, including taking down of unserviceable GI tubing complete all as specified and as directed.
66Cutting chases, pinning in, making good to facing where required and pointed in cement mortar 1:3 and making good cutting exceeding 10 cm girth complete all as specified and as directed. Note: Cutting chases will be carried out by using mechanical means like Groove cutter/ wall chaser.
67Supply & Fixing in repairs, Gun Metal Globe or Gate Valve of Class - I Pressure Tested of 1.5 Mpa, 20 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS-778, ISI Marked complete all as specified and as directed.
68Supply and fixing in repairs Stainless steel kitchen sink with draining board, made of stainless steel sheet of 1 mm thick, with plugs, washers, Waste Fittings, 32 mm dia, Brass, Chromium plated, and 32mm dia PVC flexible Waste Pipe, 750 mm long, including bedding in Cement Mortar to dwarf wall or including fixing cantilever CI Brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.
69Supply and fixing in repairs Stainless Steel Kitchen Plate Rack made of 1.00mm thick stainless steel sheet of size not less than 775 X 600 X 250mm complete all as specified and as directed.
70Supply & Fixing in repairs Vitreous China Ware Wash Hand Basin, White, Flat Back of size 550 mm X 400 mm including 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible Waste Pipe and union etc. complete all as specified and as directed.
71Supply & Fixing in repairs white Vitreous China Squatting Pan \\"Orissa Pattern\\" of size 580 mm X 440 mm with integral foot rests and 'P' or 'S' Trap including provision of lime concrete bedding complete all as specified and as directed.
72S & F in repairs Vitreous China Wash Down Water Closet [Pedestal pattern], White, including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap complete all as specified and as directed.
73Supply & Fixing in repairs 10 Litres capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia and union etc. including brackets and connections to pipe complete all as specified and as directed.
74Supply & Fixing in repairs 600 mm X 450 mm Bevelled Edge Mirror of selected quality glass, 6 mm thick and fixed to wooden plug with CP brass screws and cup washers complete all as specified and as directed.
75Supply and fixing in repairs Bib Taps, 15 mm dia, brass, Chromium Plated, Fancy Type, long Body with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified and as directed.
76Supply and fixing in repair angle stop valves, 15 mm bore dia of pipe, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc complete all as specified and as directed.
77Supply & Fixing in repairs 15 mm bore, Pillar Taps, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered \\"Hot\\" or \\"Cold\\" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.
78Supply & Fixing in repair PVC connections 15 mm size with PTMT nuts of length 450 m complete all as specified and as directed.
79Supply and fixing in repairs 32 mm dia and 800mm long PVC flexible corrugated waste pipe for wash basin/sink complete all as specified and as directed.
80Supply and fixing in repairs 32 mm dia Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connectionsincluding necessary packing, union and cap complete all as specified and as directed.
81Supply & Fixing in repair 125mm dia CP brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass complete all as specified and as directed.
82Supply and fixing in repairs Soap Dish, Stainless steel of approximate size 110 mm with brass screws complete all as specified and as directed.
83Supply & Fixing in repair Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws, wooden rawl plugs complete all as specified and as directed.
84Supply and fixing in repair of Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long including fixing arrangement complete all as specified and as directed.
85Supply and fixing in repair of Corner Glass Shelf assembly 250mm radius, made with 12mm thick acrylic glass with CP railing, fixed with brackets complete all as specified and as directed.
86Material and labour PVC(SWR) floor trap, 75mm dia outlet, plain with grating including jointing with solvent complete all as specified and as directed.
87Dismantling rain water pipe/sewage line pipe pipe 75/110 mm dia including clamps complete all as specified and as directed.
88Supply and fixing 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors /fixed on wall including clamps complete all as specified and as directed.
89Supply and fixing 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors /fixed on wall including clamps complete all as specified and as directed.
90Supply and fixing PVC (SWR) bends any radius, 110mm bore including jointing with solvent cement complete all as specified and as directed.
91Supply and fixing PVC (SWR) bends any radius, 75mm bore including jointing with solvent cement complete all as specified and as directed.
92Supply and fixing 110mm bore PVC (SWR) junction, single (single T) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.
93Supply and fixing PVC (SWR) vent cowl of 110mm dia including jointing with solvent cement complete all as specified and as directed.
94Supply and fixing PVC (SWR) vent cowl of 75mm dia including jointing with solvent cement complete all as specified and as directed.
95M & L for water proofing treatment to sunken portion of WCs, bathroom etc by applying coating of cement slurry wixed with acrylic based polymer modified cementious composite compound of approved make and as per technical instruction 5/2023 as detailed here as under:- (a) Applying 15mm thick plaster in CM 1:4 with integral water proofing compound @ 2% of weight of cement on floor and walls, finish the surface even and fair without using extra cement. The surface shall then be cured and allowed to dry.(b) Applying 1st layer of slurry of cement @ 0.488 Kg/Sqm mixed with acrylic based polymer modified cementious composite compound @ 0.253Kg/Sqm. This layer will be allowed to air cure for 04 hours.(c) Applying 2nd layer of slurry of cement @ 0.242 Kg/Sqm mixed with acrylic based polymer modified cementious composite compound @ 0.126Kg/Sqm. This layer will be allowed to air cure for 04 hours followed with water curing for 48 hours.
96Material and labour for 200mm thick shingle of size 20mm stone agrregates loose filling in floors complete all as specified and as directed.
97Material and labour for PCC 1:3:6 type C2, using 40 mm graded stone aggregate as in sunken floor complete all as specified and directed.
98Material and labour for Providing 40mm thick PCC 1:2:4 type B-1 20 as in sunken floor mixed with water proofing compound as per manufacturer instructions to horizontal or vertical surfaces including necessary form work etc complete all as specified and asdirected.Note: WPC shall be measured and paid seperately.
99Supply and fixing 50mm dia GI pipe of medium grade as in spouts complete all as specified and as directed.
100Demolition of brick work of any description and in any position built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.
101Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.
102Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for Key, scrubbing down with water etc. complete all as specified and as directed.
103Material and labour 10mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.
104Material and labour for rendering 5mm thick in cement mortar 1:4 over a backing coat of 10mm thick in CM 1:6 on concrete or brick masonry surfaces including mixing water proofing compound @3% by weight of cement in top coat and finishing the top surface even and smooth without using extra cement complete all as specified and as directed.Note: Water proofing compound will be measured and paid separately.
105Supply only integral water proofing compound (WPC) of best quality (ISI marked).
106Material and labour for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.
107Material and labour for preparation of new or previously untreated wall surfaces and applying three coats of white wash complete all as specified and asdirected.
108Material and labour for preparation of new or previously untreated ceiling surfaces and applying three coats of white wash complete all as specified and as directed.
109Material and labour for repairing of damaged surfaces of Beams, Columns, Fins, Facias, Parapets etc by trimming, cleaning the surfaces and applying 10mm thick plastering in CM 1:3 complete all as specified and as directed by the Engineer-in-Charge. Note:- Cost of scafolding upto 4m hight of building is included in this item.
110Material and labour preparation of old steel surfaces of any description over 10 cm width or girth applying one coat of synthetic enamel paint complete all as specified and as directed.
111Material and labour for preparation of old decorated plastered or unplastered wall surfaces including brooming down or steel wire brushing , scrapping down smoke, soot , moulds , moss and efflorescent salts and trading oil and greasy spots etc and applying two coats of white wash complete all as specified and as directed.
112Complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc by skilled labour complete all as specified and as directed.
113Material & Labour for waterproof cement based putty @ 1 Kg(undiluted) per sq mtr. of average thickness 1 mm apply over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps:-Step 1) Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute.Step 2) Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI Step 3)Allow 6-8 hrs time to dry the putty surface.
114Material and labour for Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint complete all as directed.Notes:- (a) Column, beam, chajja has to be painted with different colour as per direction of Engineer-in-Charge.(b) Work should wear appropriate personal protective equipment and double scaffolding for painting height upto 4.0 mtr.
115M&L for applying two coats of oil bound distemper on lod surfaces as per manufacturer guidelines using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.
116M&L for applying two coats of oil bound distemper including primer as per manufacturer guidelines using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.
117Note for serial item No. 112 to 115 :- (a) The work pertaining to periodical services & Water Proofing shall be executed from authorized applicator through manufacturer of which the materials .i.e. Paint, Distemper, Putty etc. is proposed to be used by the contractor and approved by Garrison Engineer.(b) Cost of scafolding upto 4m hight of building is included in this item.(c) Sanding of the surface to be done by mechanical sander with 1500/2700 rpm with internal dust extraction system for clean environment certified by paint manufacturer.(d) The work shall be executed by authorized reps of the approved manufacturer. The contractor shall submit the ‘Memorandum of understanding’ (MOU) with one of the approved manufacturer before placing the work order.(e) 05 years guarantee of painting work will be admissible after date of completion and 15% amount will be reserve against item No. 110 works after date of completion for the 05 years.
118Taking down carefully copper/aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc including removing from site for taking credit and making good to disturbed surface of walls, floors etc as per existing complete all as specified and as directed.
119Material and labour for concealed point wiring with FRLS stranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated cable 1100 volts grade drawn through PVC conduit including all accessories etc ISI marked in concealed with GI sunken boxes with earth dolly and cover plate with frame suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 Sqmm (nominal area) single core cable as earth continuity conductor connecting to common earth dolly for one light point/ fan point/ bell point complete all as specified and as directed.Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. (ii) Cutting chases will be carried out by using mechanical means like Groove cutter/ wall chaser.(iii) payment for cutting chases shall deemed to be included in the quote rate.
120All as per item No 117 above but with FRLS stranded copper conductor 2.5 sqmm (nominal area), two single core, PVC insulated and unsheathed cable 1100 Volt grade ISI-694 marked for 3 pin 5 Amp socket outlet point controlled by one switch on same board including 2.5 sqmm earth continuity wire complete all as specified and as directed.
121All as per item No 118 above but for 3 pin 5 Amp socket outlet point controlled by one switch on independent board complete all as specified and as directed.
122All as per item No 117 here in before but for power point controlled by one 15 Amp switch on independent board with 2.50 sqmm PVC (FR-LS) insulated un-sheathed copper conductor cable multistranded conductor 1100 volts grade and 2.50 Sqmm PVC (FR-LS) copper conductor cable as earth continuity conductor.
123All as per item No 117 above but with FRLS 4 sqmm starnded copper conductor for one power point on independent board and including 4 sqmm earth continuity wire for AC/equipments etc controlled by one SP/SPN MCB. Note: (i) The point wiring will be done from DBs to the switch sockets of any size with three wires running independently for each point and with no tappings. (ii) MCB will be measured and paid separately.
124Supply & Fixing ceiling rose surface bakelite with three terminals complete all as specified and as directed
125Supply and fixing modular switch, 1 way, 6 A, 1 module complete all as specified and as directed.
126Supply and fixing modular socket, 6 A, 2/3 pin, 2 module complete all as specified and as directed.
127Supply and fixing Switch socket outlet multipurpose 3 pin, 16 amp and one pin, 6 amp controlled byone switch complete all as specified and as directed.
128Supply & Fixing bell push modular type 5 Amps complete all as specified and directed.
129S & F Call bell, Ding dong AC, 230 Volts, Single Pole complete all as specified and as directed.
130Supply & Fixing lamp angular holder insulated body with back plate suitable for batten fittings complete all as specified and as directed
131Material & Labour for sub main wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 6.0 sqmm (Nominal area) drawn through in and including concealed PVC rigid conduit of adequate size with all accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 6.0 sqmm as earth lead and connected to earth dolly and including taking down old unserviceable sub main wiring of any description, making good to disturbed surfaces complete all as specified as directed. Note : (i) 3 Runs of 6.0 Sqmm cable and one run of PVC rigid conduit of 20mm dia shall be measured as one unit length.
132Material & Labour for sub main wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 4.0 sqmm (Nominal area) drawn through in and including concealed PVC rigid conduit of adequate size with all accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 4.0 sqmm as earth lead and connected to earth dolly and including taking down old unserviceable sub main wiring of any description, making good to disturbed surfaces complete all as specified as directed. Note : (i) 3 Runs of 4.0 Sqmm cable and one run of PVC rigid conduit of 20mm dia shall be measured as one unit length.
133Material & Labour for sub main wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 1.5 sqmm (Nominal area) drawn through in and including concealed PVC rigid conduit of adequate size with all accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly and including taking down old unserviceable sub main wiring of any description, making good to disturbed surfaces complete all as specified as directed. Note : (i) 3 Runs of 1.5 Sqmm cable and one run of PVC rigid conduit of 20mm dia shall be measured as one unit length.
134Supply and fixing in repairs Surface & wall mounted Energy efficient LED Tube Light Fitting, of 20 W, 6500 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95
135Supply and fixing in repairs Surface & wall mounted Energy efficient LED Tube Light Fitting, of 10 W, 6500 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95
136Supply and fixing in repairs LED bulb, 9 W, Correlated colour temperature 3000 K, ball shape, Base type E-27 with facility to provide upto 04 hours backup, energy efficient, 5 star rated complete all as specified and as directed. Note: Light fitting shall be of PF>0.95
137Supply & Fixing Energy efficient & Long life Building Security Light Luminaire, of 25 watt, 5700 K with Pressure Die Cast Aluminium Housing, IP66 protection, heat resistant glass cover, high power LEDs as light source, electronic driver including GI Bracket made out of 40 mm bore GI Tube, Medium Grade of size not exceeding 1.00 m in length and bent to shape required and fixed with 2 Nos of Pole fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95
138Supply & Fixing Energy efficient, Low Noise, Ceiling Fan, 1200mm Sweep of any colour as approved, 03 blades, BEE 5 Star Rated, with BLDC Motor, Copper Wound, 350 RPM, with Double Ball Bearing, Conforming to IS - 374, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50Hz, including Down Rod, Canopies, Shackles, Safety Rope, Hanging Clamps, Bushes, having P.F >0.95, Service Value >6.5, Air Delivery >215 CMM, Power Consumption less than 35 Watt, THD less than 5% including provision of Electronic speed control Regulator step type, including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and taking down existing ceiling fan of any description and depositing at MES Store Yard complete all as specified and as directed. Note: Ceiling Fan shall be provided with 03 Years onsite replacement warranty. Rate quoted is deemed to be including the same and nothing shall be paid extra on this account.
139Supply and fixing in repair Decorative LED wall mounting, Champagne gold finish fixture with plastic body of 9 W, Base type B-22 LED lamp complete all as specified and as directed. Note: Light fitting shall be of PF>0.95
140Supply & Fixing plastic body exhaust fan 250mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with 3 core flexible copper cable including making holes on the wall and making good to the disturbed surfaces including taking down and removing old UNSV fan and depositing to MES store yard complete all as specified and as directed.
141Supply & Fixing Exhaust Fan, 300mm Sweep, 1200 RPM, Metal Body, Heavy Duty, with Double Ball Bearing, Conforming to IS - 2312, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50 Hz, including Louvers Shutter / Grill, BEE 5 Star Rated and of approved colour including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and fixing in existing opening and making good the disturbed surface to match with existing and taking down existing ceiling fan of any description and depositing at MES Store Yard complete all as specified and as directed.
142S & F Energy efficient, BEE 5 Star rated Storage type Water Heater [Geyser] 25 Litres Capacity with 2000 Watt Capacity heating element Conforming to IS - 2082, Vertical Storage type with Stainless Steel Inner Tank and ABS Outer Shell complete fixed to wall with suitable expansion fasteners including 02 Nos. of 450 mm long x 15mm dia Stainless Steel braided Flexible Hot & Cold Water connections and 15mm bore Non-Return Valve and including disconnecting and removing old unserviceable Water Heaters of any description and depositing at MES Store Yard complete all as specified and as directed.
143Supply and fixing of MCB DB SPN 12 ways, powder coated, double door, 230 Volts, including bus bar neutral link, earth bar and din rail, for fixing MCB of various rating including taking down old unserviceable DB alongwith MCBs including making good disturbed surfaces complete all as specified and as directed.
144Supply & Fixing in repairs of SP & N Enclosure with 2 Pole and Earth Metal Plug & Socket for incorporating SP MCB complete including One MCB, SP, 20 Amps, 240 Volts complete all as specified and as directed.
145Supply & Fixing of MCB SP of capacity 6-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed.
146Supply & Fixing of MCB SPN of capacity 40-63 Amps, 240 V, 10 KA 'C' curve complete all as specified and as directed.Note for serial Item No. 141 to 144: MCB and MCB DB, SPN enclosure shall be of same make as approved by GE.
147Supplying, Installing, Commissioning and Testing of CPRI Prototype tested, Factory made, Free Standing Floor Mounted, Dust and Vermin proof LT Panel board, Compartmentalised, Indoor type, fabricated with 2.00mm thick CRCA Sheet and shall be given pre-treatment for degreasing, phosphatising etc. in seven tank process and shall be powder coated with RAL7035 coat with matt finish after due preparation of surfaces. The panel shall consist of aluminium bus bars of high conductivity of suitable size and shall be provided with colour coded heat shrinkable sleeves mounted on porcelain insulator supports, suitable double Compression Copper Cable Glands and panel shall be provided with separate compartments for each switch, with gland plates, lifting hooks, shutter type ventilating louver at both top & bottom duly internally secured with wire mesh, with suitable internal wiring with copper cable of suitable size, including instrumentation such as Ampere Meter, Volt Meter, Phase Indicating LED Lamps [RYB], Selector Switches etc with double stud hinged door, front openable with locking arrangement including interlocking with switch gears and suitable for 1100 Volts Grade, 3 Phase, 415 Volts, 4 Wire, 50 Hz, AC Supply and to withstand short circuit fault level of not less than 100KA and degree of protection shall be IP 54. (Cont...)
148The panel shall be fixed with angle iron frame made of angles of size 40X 40 X 5mm at Corners and ISMC of suitable size for base, embedded 600 mm below ground level in PCC 1:2:4, Type B–1 using 20mm grade stone aggregate, 600 mm above ground level complete including connecting up with existing incoming and outgoing cables etc. and comprising the following(Main Panel No. 1) :[a] MCCB, 100 Amps, FP, 16 KA, 415 Volts, 3 Phase, AC, 50 Hz, Adjustable type complete with Overload Protection, no-volt thermal based release – 1 No. [Incoming][b] MCB, 40-63 Amps, SPN, 10 KA, 415 Volts, 3 Phase, AC, 50 Hz, B Curve – 5 Nos [Outgoing][c] MCB, 20 Amps, SPN, 10 KA, 230 Volts, B Curve – 2 Nos [Outgoing][d] Aluminium bus bar 125 Amps of suitable size and length duly insulated with colour code-04 Nos.[e] Providing sufficient space for fixing of 05 Nos. electronic meter.[f] Digital type Ammeter of Range 0 – 500 Amps with CTs & Selector Switch – 4 Nos [1 Set].[g] Digital type Voltmeter of Range 0 – 500 V with Selector Switch – 1 Nos.[h] Colour Coded LED Phase Indicating Lamps for each Phase – 1 Set.
149Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion including taking down old unserviciable earthing set all as specified and as directed.Notes:-(i) Main earthing strip from earth plate electrode to rest point upto length of 7.5 meters length shall deemed to be included in the unit rate quoted against this item. (ii) On testing after completion if the desired resistenance is not obtained the contractor shall redo the earthing without any extra cost to the department. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58297989
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 78.17 Lakhs
LAST DATE 27-11-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Special Repairs To Bldg No. P-134 At Dacca Colony At Masimpur Mil Stn
Basic Detail
Tender No 8188/E8
Bidding Type Tender
Location
City Cachar
State Assam
Key Dates
Publish Date 30 Oct 2026
Submission Date 27 Nov 2026
Open Date 04 Dec 2026
Finance
Tender Value 78.17 Lakhs
Tender Fee 1000
EMD 1.42 Lakhs
Exemption Not Available
Document List
639cc4fa-305a-46c6-9dc9-aabf9a695acf.html
8188TenderDocu.pdf
BOQ_893416.xls
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Oct 30, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 27, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 10 days
Dec 04, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 17 days

Tender Documents

Download All (ZIP) ↓
html

639cc4fa-305a-46c6-9dc9-aabf9a695acf.html

pdf

8188TenderDocu.pdf

xls

BOQ_893416.xls

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender