Tender For Special Repair To Roof, Sunken Floor And Other Connected Items In P-896, 897, 898 And P-899 Otm Accn At 339 Med Regt Under Ge (W) Jalandhar Cantt
Tender Value
46.23 Lakhs
Estimated cost
Bid Submission
18 Nov 2026
13 days left
EMD
92460
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalandhar → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Roof, Sunken Floor And Other Connected Items In P-896, 897, 898 And P-899 Otm Accn At 339 Med Regt Under Ge (W) Jalandhar Cantt
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete in ground floor and paving n.exc 15 cm thick (below or above ground level complete . |
| 2 | Taking down cement plastering on stone wall/brick wall etc including racking out of joints hacking for key scrubbing down with water etc |
| 3 | M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions of walls shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and as junction of walls. |
| 4 | M&L 10mm thick rendering in CM 1:3 on brick/concrete surface as in ceiling and finishing the surface even and smooth with out using extra cement. |
| 5 | M&L 15mm thick rendering with water proofing liquid as per manufacturere instruction of approved make on wall in CM 1:4 on brick/concrete surface and finishing the surface even and smooth with out using extra cement. |
| 6 | M&L 15mm thick rendering on wall in CM 1:6 on brick/concrete surface and finishing the surface even and smooth with out using extra cement. |
| 7 | Demolition of floor hearth or wall tiling including cement mortar bedding (not backing ) removing serviceable tiles to store and rubbish of the premises |
| 8 | M&L coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick cement plaster in CM 1:4. |
| 9 | M&L Non skid Coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exce 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6. |
| 10 | Demolition of cement concrete above ground floor and paving exc 15 cm thick (below or above ground level complete . |
| 11 | M&L for 15mm thick rendering in 1:3 CM with water proofing liquid as per manufacturere instruction of approved make as in sunken portion complete all as directed. |
| 12 | M&L for applying evenly a tack coat of industrial bituminous 85/25 @ 1.20 Kg per squqre mtr including cleaning surfaces. |
| 13 | M&L APP based polymeric membrance minimum weight not less than 3.0kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/Sqm) land on primed surface by forced application( sealed by gas flame) with over lap of 15 cm complete all as specified and directed complete all as spd and directed. |
| 14 | M&L Cement concrete type E-2, 1:5:10 using 40mm graded aggregate in foundations filling and mass concrete as in sunken floor. |
| 15 | Cutting holes into or through brick walls built, in cement mortar Superficial area N.exc 150 sq. cm upto 23cm of depth of wall. |
| 16 | M&L for 50mm dia GI pipe,med grade beveled cut at both ends by making hole in walls sunken portion aprox above the RCC slab and ceiling finished the hole with cement plaster 1:2 to match with existing surface complete etc.(Measured for cutting holes shall be paid in concerned sch item) |
| 17 | Taking down chowkats or frames with shutters (with out taking of shutter from the frame) of any description alongwith fittings exc 1.5 Sqm n.exc 4 Sqm each |
| 18 | S&F Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube |
| 19 | S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing. |
| 20 | S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average with aperature 1.18 mm fixed with tinned tacks, or galvanised wire staples. |
| 21 | M&L for 4.80mm thick sheet glass ordinary quality glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed. |
| 22 | S&F Butt hinges, medium weight cold rolled 100 mm size ISI marked. |
| 23 | S&F aluminium anodised barrel tower bolts of extruded section 150mm long all as specified. |
| 24 | S&F Extruded aluminium alloy handles fabricated type anodised 150mm size |
| 25 | Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. |
| 26 | Taking up or down 20 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. |
| 27 | S&F 15mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. |
| 28 | Refixing 15mm old GI tubing and connections in new or old position (Walls, ceiling, floors, etc.) |
| 29 | S&F 20 mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. |
| 30 | Refixing 20 mm old GI tubing and connections in new or old position (Walls, ceiling, floors, etc.) |
| 31 | Cutting chases, pinning in making good to facings where reqd and pointing in cement mortar 1:3 to ends or edges of shelves , for water tubing etc and making good, cutting exc 10cm girth but not exc 20cm girth in stone walls |
| 32 | Dismantiling of water tanks of capacity exc 250 & n exc 500 ltrs incl all necessary fittings complete. |
| 33 | S&F 500 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd in SSR part-I |
| 34 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning of over head tank 500ltr capacity of any description and capacity, descaling, washing with detergent powder, removing vegetation around the over head tank/plat foRM complete all as specified and directed. |
| 35 | S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair |
| 36 | S&F ball float valve brass with epoxy coated aluminimum rod for 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe. |
| 37 | S&F in repair 15mm dia Bib taps cast copper alloywith fancy type chromium lated crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule |
| 38 | S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup concealed type screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs. |
| 39 | S&F 15mm dia Brass stop valves chromium plated, fancy type with cup screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlons as specified and fixed in repairs. |
| 40 | S&F in repair 15mm dia fancy type pillar taps cast copper alloy with capstan heads chromium plated scewed down high pressure with long scrwed shanks and fly nuts screwed for iron pipes |
| 41 | S&F in repair waste Coupling Suitable for Existing WHB/Sink all as specified |
| 42 | S&F in repairs waste pipe suitable for Existing WHB/Sink all as specified |
| 43 | S&F 600x450 bevelled edged looking mirror 2mm thick of selected quality glass, mounted on 4 mm thick PVC sheet and with aluminnium frame work fitted with chromium plated brass screws and cup washers including taking old one. |
| 44 | S&F Vitreous China wash down Water closet pan (pedestal pattern) \\"with plastic water closet seat cover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging divice (excluding flusing cistern and flush pipe) in repairs complete. |
| 45 | S&F in repairs Vitreous Chinaware squatting pan, orissa pattern size 580mm x 440mm with integral foot rests, white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, including provision of lime concrete, making connections to trap and to flush pipe etc. and making good to floors, complete all as specified and directed. |
| 46 | S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dis for low level cistern in repairs |
| 47 | S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality as specified |
| 48 | S&F in toilet paper holder of brass chromium plated fixed to walls with brass screws |
| 49 | Supply and fixed CP Soap dish, any type fixed to walls with plugs with chromium plated brass screws |
| 50 | S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as spd and directed. |
| 51 | S&F Health faucet/jet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25mtr long flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified. |
| 52 | M&L 75mm PVC (SWR) floor trap , plain with CP grating including jointing with solvent cement complete all as spd and directed |
| 53 | S&F in repair brass chromium plated shower rose 125mm size complete all as spd and directed. |
| 54 | Dismantling of brick tiles single layer as in roof covering complete all as specified |
| 55 | Demolition of mud in roofs any thickness including plastering and leeping(whether full thickness removed or only a part thereof) all as specified. |
| 56 | Cleaning/Roughening surfaces of old concerete floor/roof by picking , sweeping clean and washing down with water to romove the dust etc complete all as spd. |
| 57 | (i) M&L for providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges and PCC pedding with cement concrete type B-1, 1:2:4 (using 12.50mm graded stone aggregate) to top surface of slab in slop 1:40,with using water proofing liquid as per manufacturer instruction of approved make, finishing the surface even and smooth without using extra cement complete all as specified. |
| 58 | (ii) M&L 15mm thick rendering with water proofing liquid as per manufacturere instruction of approved make on wall in CM 1:4 on brick/concrete surface and finishing the surface even and smooth with out using extra cement (iii) Providing and applying Epoxy primer (02 fast component resin of hardner) on the prepared surfacev @200gm per Sqm. (iv) Providing and applying Liquid Polyurea - PU based hybrid elestomeric water proofing membrane at existing/newly constructed roofs. Double coat is required on the smooth and cleared surface @ 1.50Kg per Sqm. (v) After coating of primer of two coats of ULTRON (US) a proper protective plaster/layer is to be done by laying Geo textile and 40mm screed on the top of final coating. Note:- Ser No (i) to (v) : The application shall be done by the authorised applicator of the manufacture with a letter of proof stating the authenticity of the applicator fiRM. |
| 59 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) |
| 60 | Dismantling of cast iron or reinforced concrete drain pipes of size 75-100mm dia, jointed in cement mortar and taking out of trenches, if required. |
| 61 | S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete |
| 62 | S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls |
| 63 | S&F110mm PVC (SWR) bends |
| 64 | S&F75 mm PVC (SWR) bends |
| 65 | S&F for PVC 110mm (SWR) vent cowl |
| 66 | M&L for repairing of R.C.C projections, chajjias, roofs, facia etc in patches not exceeding 3 Sqm in each patch by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.,C.C surfaces and applying one coat of cement slurry and filling the surfaces with cement concreat (1:1.5:3) using 12.5mm graded crushed stone aggrigates and reinforced with welded mesh (If Reqd) of weight exc 2 kg per Sqm but n.exc 3kg/Sqm with or without facia and finished with cement and sand motar (1:3) using coarse sand and work in patches area n.exc 5 Sqm each and thickness of R.C.C member n.exc 75mm including necessary foRM work and applying two coats of finishes to match with the existing surfaces in at any height complete all as specified and directed. (Note : Cost of foRM work and welded mesh shall be deemed to be included in unit rate quoted by the contractor complete all as specified and as directed. |
| 67 | M&L for applying one coat of synthetic enamelled paint including preparation of old decorated steel surfaces of any description not otherwise described over 10 CM girth or width all as directed. |
| 68 | M&L for applying white wash of 3 coats on ceiling incl preparation newly plastered surfaces as specified and directed. |
| 69 | Complete removal of existing treatment and applying Two coat of white wash on ceiling incl preparation old plastered surfaces as specified and directed. |
| 70 | M&L for preparation of new plastered surfaces of walls applying two coat of exterior emulsion paint over and incl a coat of primer as per manufacurers instructions and directed. |
| 71 | M&L for preparation of old surfaces of walls incl, scraping down smoke soot, moulds, moss & efflorescent salts & trading oil and greesing spots etc & applying one coat of exterior emulsion paint as per manufacurers instructions and directed. |
| 72 | Material and labour for preparation of new plastered surfaces on walls and applying two coats of oil distemper on one coat of thin layer of putty, on plastred surfaces over one coat of chalk whitening complete all as specified. |
| 73 | Complete removal of existing treatment on wall and applying Two coat of Oil distemper (white or tinted) on one coat of thin layer of putty , on old plastred surfaces, prepara-tory to distempering on walls etc (Surface finished even and smooth) complete all as specified and as directed. |
| 74 | Taking down carefully aluminium / copper point wiring (light / fan / socket or power) while not disturbing existing conduit complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls and floors and one coat of putty and two coat of distemper as per existing colour complete all as directed . |
| 75 | Taking down sub main wiring of two single core PVC cable PVC insulated 4 / 6/10 sqmm including conduit or wooden batten and remove from the site of work and making good the disturbed surfaces of wall or floor etc. and one coat of putty and two coat of distemper as per existing colour complete all as directed. |
| 76 | Taking down main switch / DB and making good the disturbed surface and one coat of putty and two coat of distemper as per existing colour complete all as directed. |
| 77 | M&L for point wiring with 1.5 sqmm, PVC insulated but sheathed, stranded copper conductor single core FRLSH cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit medium grade 20mm dia (minimum) or higher size as specified and cutting chasing on wall complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc/ fittings ISI marked for fittings and brass screws and cup washers including 1.5 sqmm stranded copper conductor PVC insulated FRLSH cable green in colour as continuous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed. (a)One light / fan / call bell point controlled by one, one way switch. |
| 78 | (b) One 3 pin socket out let 5 Amps on same board with other switches. |
| 79 | (c) 'One 3 pin socket out let 5 Amps on the independent board. |
| 80 | All as per item No.77 above but with 2.5 sqmm multistranded copper multistranded conductor FRLSH cable with 1.5 sqmm earth wire for one 6 pin socket outlet 15 amps on independent board |
| 81 | S&F switch Piano 5 Amps, flush button type, SP, one way, 230 Volts, AC |
| 82 | S&F switch Piano 15 Amps, flush button type, SP, one way, 230 Volts, AC |
| 83 | S&F socket out let multipurpose 5 pin 5 Amps, flush type, 230 / 250 Volts |
| 84 | S&F socket combination ,6 pin ,15 amps, flush type, multipurpose, 230 / 250 volts , AC with ISI marked |
| 85 | M&L ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified. |
| 86 | Supply and fix MCB DB, TPN 6 way double door Vertical type suitable for mounting of MCCB as incomer with suitable 200 amps rated bus bars , Neutral links , blanking plates Distribution boards should be Double Door design with IP-43 and IK-08 rating as per IEC 61439-3 with 200 Amp fully insulated copper busbars, insulated neutral bar, earth bar and cable ties for cable management. Distribution board should be supplied with door earthing, prefitted masking sheet, reversible doors and pan assembly for easy installation including thermal based release adjustable type 4 pole 63 Amps MCCB, 50 Hz, 415 Volts with rupturing capacity 16 KA. Must have possibility of converting lock to panel lock complete all as specified and directed. All 3 Phase horizontal distribution boards should have the provision to convert the distribution boards to Per Phase Isolation Distribution Board at site. All MCCB incomer distribution boards should be supplied with 250 Amp rated fully shrouded busbars. |
| 87 | Supply and fix Sheet metal DB,double door, SPN 8 way for MCB, 240 volt with 200 amps rated bus bar , neutral bar / connectors suitable copper thimbles , lugs etc. Distribution boards should be Double Door design with IP-43 and IK-08 rating as per IEC 61439-3 with 100 Amp fully insulated copper busbars, insulated neutral bar, earth bar and cable ties for cable management. Distribution board should be supplied with door earthing, prefitted masking sheet, reversible doors and pan assembly for easy installation. Must have possibility of converting lock to panel lock complete all as specified and directed. |
| 88 | S&F MCB SPN, 240 volts, 40 to 63 Ampere, rupturing capacity 10 KA, ‘B’ curve type ,MCB should be having the Breaking Capacity of 10 kA and should be ISI marked as per IS/IEC 60898-1 2002 with “B” Curve Characteristics. Should have bi-connect terminals on the bottom terminals for looping and should have 35 sq mm termination capacity on both terminals with insulated sliding shutters for making it IP-20 protected & with two position DIN Rail Clamp for easy mounting. complete all as specified and directed. |
| 89 | Supply & Fixing MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type ,MCB should be having the Breaking Capacity of 10 kA and should be ISI marked as per IS/IEC 60898-1 2002 with “B” Curve Characteristics. Should have bi-connect terminals on the bottom terminals for looping and should have 35 sq mm termination capacity on both terminals with insulated sliding shutters for making it IP-20 protected & with two position DIN Rail Clamp for easy mounting. complete all as specified and directed. |
| 90 | M&L Lamp holder, PVC/Polycarbonate type with back plate incl 01x LED bulb 09 Watt 5-star rating complete suitable for batten fittings. |
| 91 | Supply & fix Exhaust fan made of Sturdy engineering plastic complete with Louvers shutter voltage 230 volts , 50 Hz ,1200 RPM copper winding of sweep 300 mm weep , incl making opening in wall for fixing the exhaust fan with louvers complete all as specified and directed. |
| 92 | S&F in replacement LED tube light fitting 20W (Double side) including LED lamp 20W with 2100 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI-6500K (White light) fixtures box type and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed. |
| 93 | M&L for concealed conduit sub main wiring of 2 run of single core multi stranded FRLSH PVC insulated and unsheathed copper conductor as per IS-694 FRLSH cable red and black colour of size 6 sqmm 1100 volts grade with 6.0 sqmm multi strand copper conductor PVC insulated and unsheathed cable in green colour earth continuity wire connected to common earth dolly in PVC pipe including cutting chasing complete with all accessories as specified and directed. |
| 94 | M&L for earthing complete with GI steel earth plate electrod 60x60cmx6.00mm thick bouried directly in ground /earth pit not less than 2.25m deep below the ground level with top edge of the plate not less than 1.5 m below the normal ground level connected to test point by using GI wire of dia 4 mm as earthing lead soldering/revated to earth plate at one end and connected DB by means of nut, bolts etc complete with PCC pit (1:3:6) type GI cover with handle funnel with watering pipe wire mess GI protection pipe for earthing lead all complete as specified and as per electric plate No.5 of SSR Part I Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysNov 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender