Tender For Execution Of Renovation & Allied Works-Dharmshala Block (1St Floor) At Homi Bhabha Cancer Hospital & Research Center, Agan Udi, Visakhapatnam Ap-Reg.
Tender Value
85.67 Lakhs
Estimated cost
Bid Submission
19 Nov 2026
13 days left
EMD
1.71 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Visakhapatanam → Andhra Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Execution Of Renovation & Allied Works-Dharmshala Block (1St Floor) At Homi Bhabha Cancer Hospital & Research Center, Agan Udi, Visakhapatnam Ap-Reg.
BOQ
| Sl. No. | Item Description |
| 1 | It is advised to visit the site to acquaint themselves with the nature and location of work before quoting tender. The Quantities which are prescribed may vary (+/-) as per site condition. |
| 2 | Civil Works |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. - All kinds of soil |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift, as directed by Engineer-in-charge. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) as directed by Engineer-in-charge. |
| 7 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement:1:1.5:3 (1 cement : 1.5 coarse sand(zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanicaly Treated bars of grade Fe-500D or more. |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 10 | Foundations, footings, bases of columns, etc. for mass concrete |
| 11 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 12 | Suspended floors, roofs, landings, balconies and access platform |
| 13 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 14 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 15 | Brick work with common burnt clay F.RS. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) |
| 16 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in : Cement mortar 1:3 (1 cement: 3 coarse sand) |
| 17 | Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry. |
| 18 | Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement: 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work,as directed by Engineer-in-charge. |
| 19 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture fixed using suitable Aerolite adhesive material, joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble.Area of slab over 0.50 sqm,as directed by Engineer-in-charge. |
| 20 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels - Granite stone slab of colour black |
| 21 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. - Granite Work |
| 22 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete as directed by Engineer-in-charge. |
| 23 | Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. - 8 mm thick - Granite of any colour and shade |
| 24 | Providing and fixing granites for Cupboards shelf with all necessary material as per direction of engineering in-charge. |
| 25 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. - Granite Stone of approved shade,as directed by Engineer-in-charge. |
| 26 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete - 100X58X1.90 mm,as directed by Engineer-in-charge. |
| 27 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 200x10 mm,as directed by Engineer-in-charge. |
| 28 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.as directed by Engineer-in-charge. |
| 29 | Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete.Size 40 mm,as directed by Engineer-in-charge. |
| 30 | Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete - 100x63x3.2 mm.as directed by Engineer-in-charge. |
| 31 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 32 | 200x10 mm |
| 33 | 150x10 mm |
| 34 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125mm,as directed by Engineer-in-charge. |
| 35 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single Rubber Stopper,as directed by Engineer-in-charge. |
| 36 | Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade I Type II), having one side decorative lamination and other side balancing lamination, including llnd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge |
| 37 | Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately). - 12 mm thick commercial ply conforming to IS : 1328 BWR |
| 38 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete,as directed by Engineer-in-charge. |
| 39 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 40 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate,as directed by Engineer-in-charge. |
| 41 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 42 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS 15622 (thickness to be specified by the manufacturer) of approved make in al colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 43 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in al colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. - Size of Tile 600x600 mm,as directed by Engineer-in-charge. |
| 44 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. - Size of Tile 600x600 mm,as directed by Engineer-in-charge. |
| 45 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand),as directed by Engineer-in-charge. |
| 46 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade :Two or more coats on new work,as directed by Engineer-in-charge. |
| 47 | Polishing on wood work with ready mixed wax polish of approved brand and manufacture : New work,as directed by Engineer-in-charge. |
| 48 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete,as directed by Engineer-in-charge. |
| 49 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats,as directed by Engineer-in-charge. |
| 50 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre,as directed by Engineer-in-charge. |
| 51 | White washing with lime to give an even shade :Old work (two or more coats), as directed by Engineer-in-charge. |
| 52 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work,as directed by Engineer-in-charge. |
| 53 | Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface including disposal of mulba/rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge |
| 54 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. |
| 55 | Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-incharge |
| 56 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge |
| 57 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar |
| 58 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below,as directed by Engineer-in-charge. |
| 59 | Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge. |
| 60 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm,as directed by Engineer-in-charge. |
| 61 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material withinthe hospital premises as per direction of engineering in charge. |
| 62 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within the hospital premises as per direction of engineering in charge. |
| 63 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to the Muncipal dumping ground within hospital premises beyond 50 m initial lead, for all leads including all lifts involved. |
| 64 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge |
| 65 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests,as directed by Engineer-in-charge. |
| 66 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps,as directed by Engineer-in-charge. |
| 67 | Providing and fixing Stainless Steel ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:- Kitchen sink without drain board - 610x460 mm bowl depth 200 mm,as directed by Engineer-in-charge. |
| 68 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively as directed by Engineer-in-charge. |
| 69 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm dia,as directed by Engineer-in-charge. |
| 70 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete,as directed by Engineer-in-charge. |
| 71 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 72 | 15 mm nominal dia Pipes |
| 73 | 20 mm nominal dia Pipes |
| 74 | 25 mm nominal dia Pipes |
| 75 | 32 mm nominal dia Pipes |
| 76 | Providing and fixing brass bib cock of approved quality : 20 mm nominal bore as per direction of EIC. |
| 77 | Providing and fixing C.P. brass long nose bib cock of approved qualityconforming to IS standards and weighing not less than 810 gms.15 mm nominal bore,as directed by Engineer-in-charge. |
| 78 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms - 15 mm nominal bore,as directed by Engineer-in-charge. |
| 79 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931,as directed by Engineer-in-charge. |
| 80 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts,collar and bush of approved quality and colour. - 15 mm nominal bore with 45 cm length,as directed by Engineer-in-charge. |
| 81 | Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete-450 mm dia RCC pipes,as directed by Engineer-in-charge. |
| 82 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 83 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron,as directed by Engineer-in-charge. |
| 84 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.Pre-laminated particle board with decorative lamination on both sides,as directed by Engineer-in-charge. |
| 85 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm),as directed by Engineer-in-charge. |
| 86 | Providing and fixing Brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete,as directed by Engineer-in-charge. |
| 87 | Providing and fixing 28-30 MM thick solid Wood Polymer Composite(WPC) single extruded door shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. A minimum of 4 hinges will be required for fixing the door with the frame,as directed by Engineer-in-charge. |
| 88 | Supply & Fixing of 4\\" PVC Multi Floor trap along with SS Jalli (With/without hole),as directed by Engineer-in-charge. |
| 89 | Supplying and fixing TV shape mirror with plastic frame size 609.6 mm x 457.2mm,as directed by Engineer-in-charge. |
| 90 | Supply & Fixing of Pillar cock Jaquar Continental series, Chrome Finish with 7 years warranty,as directed by Engineer-in-charge. |
| 91 | Supply & fixing 12.7 mm dia NP push cock Ist quality,as directed by Engineer-in-charge. |
| 92 | Supply & fixing towel rod (CP) of 24\\" long and 3/4 \\" dia,as directed by Engineer-in-charge. |
| 93 | Supply & Fixing of 2 in 1 Bibcock cum Health Faucet with 1m long tube and wall hook , Chrome Finish with 7 years warranty,as directed by Engineer-in-charge. |
| 94 | supply and fixing of Stainless Steel Door Handles 125 mm Long as per Direction of EIC. |
| 95 | Labour charges only for fixing European Water Closet with 'P' or 'S' trap as per standard practice,as directed by Engineer-in-charge. |
| 96 | Supplying and Fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548 as directed by Engineer-in-charge. |
| 97 | Supplying and fixing of 4mm thick UV resistant Embossed/Diamond polycarbonate(fibre) sheets (Transculent) of any colour, including necessary cutting, drilling, EPDM washer/Gasket, suitable fastener etc, fixed to the aluminium frame structure as directed by engineering in charge. |
| 98 | Providing and fixing wooden battens/pattis of size 100x50mm of approved timber, over existing aluminium partition or existing brick massonary surface, including cutting, drilling, screw,plugs , necessary supports and finishing, complete as per directed by the Engineer in charge. |
| 99 | Shifting of existing dismantled/removed material such as wooden doors frames, shutters, plumbing pipes & fitting, aluminium partition, Sanitary & CP Fixtures and other material to the designated location as instructed by engineer in charge within the hospital premises including all lead & lift. |
| 100 | Providing and applying on floor /wall of approved make crystaline /chemical water proofing system on an enitre surface etc complete as directed by engineer in-charge : providing, applying,& testing waterproofing treatment of the masonary surface/walls of toilets comprising of following methods/stages as per per approved manufacturer specification with providing of 10 years guarrantee from the vendor.surface preparation,testing to be carried out bycleaning, chipping the loose cement mortar,grinding to remove the laitance and cleaning the dust by blower/mop.hacking the surface to create 3mm to 5 mm impression to enable penetration depth and improved bonding of waterproofing layers.The final surface to be water washed/waterjet cleaned.Application of crystalline system on entire surface and appling protective screed/ plaster on the treated areas in cement mortar1:3 for thickness of 15-20mm.Rate shall be includ coving, bore packing, core cut treatment for traps etc complete as directed by Engineering in-charge.water ponding test to be done for 24 hrs to check the leakage/seepage in the strucuture and to delivered in satisfactory condition to the EIC.Note- wall height up to 1m for toilets and lift pit(including sunk portion) and other walls as per the site conditions.Mode of Measurement-Elevational area shall be measured and paid. |
| 101 | Electrical Works |
| 102 | UG-CABLES |
| 103 | Sub-Station to Dharmasala |
| 104 | U.G. Cable:-Supply and transportation of 300 Sq mm X 3.5 core XLPE insulated, 1100V grade armoured aluminum cable as per specification confirming to IS:7098 (Part - I)./1554-I |
| 105 | UG Cable Laying:- Laying of 300 Sq mm X 3.5 core armoured aluminum cable PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 106 | UG Cable Laying:- Laying and fixing of 300 Sq mm X 3.5 core armoured aluminum cable PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. |
| 107 | UG Cable Jointing & END Termination:-Supplying and making end termination of 3½ X 300 sq. mm (70mm) with heavy duty double compression brass gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 108 | CABLE TRAYS: Supply, transportation & installation of following 300mm x 50mm x 1.6mm of Hot Dipped Galvanized Iron perforated cable trays with cover, including horizontal and vertical bends, reducers tees, cross members and other accessories as required and duly suspended from the ceiling/Wall with suspenders etc., complete. |
| 109 | Supplying, making and fixing of Cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. |
| 110 | I/C Cables to DB's |
| 111 | LT Cable:-( 8-Way Power DB-01 No FF)Supply and Transportation of 4C x 25 sq.mm XLPE/PVC insulated & PVC sheathed armoured cables of 1.1 KV grade with copper conductor as per IS 7098 Part-I -1988 etc., complete. |
| 112 | LT Cable Laying:-Laying and fixing of 4C x 25 sq.mm copper Armoured cable (clamped with 1mm thick saddle), PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. |
| 113 | LT Cable END Termination:- Supply and making of 4 core x 25 sq.mm one end termination with heavy duty double compression brass gland as per BS 6121:2005, IP 66 complete, SIBG type,for following size of Armoured PVC insulated & PVC sheathed/ XLPE copper conductor cable of 1100 volt grade as required of size. |
| 114 | Cable Lugs:-Supply and making of 25 Sq.mm end termination with heavy copper lugs (pin/ ring type) as per IS specification, duly crimped with crimping tool, PVC tape etc., |
| 115 | LT Cable:-(Lift TPN DB-1No)Supply and Transportation of 4C x 10 sq.mm XLPE/PVC insulated & PVC sheathed armoured cables of 1.1 KV grade with copper conductor as per IS 7098 Part-I -1988 etc., complete. |
| 116 | LT Cable Laying:-Laying and fixing of 4C x 10 sq.mm copper Armoured cable (clamped with 1mm thick saddle), PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. |
| 117 | LT Cable END Termination:- Supply and making of 4 core x 10 sq.mm one end termination with heavy duty double compression brass gland as per BS 6121:2005, IP 66 complete, SIBG type,for following size of Armoured PVC insulated & PVC sheathed/ XLPE copper conductor cable of 1100 volt grade as required of size. |
| 118 | Cable Lugs:-Supply and making of 10 Sq.mm end termination with heavy copper lugs (pin/ ring type) as per IS specification, duly crimped with crimping tool, PVC tape etc., |
| 119 | CABLE TRAYS:-[Lift TPN DB-01no & 8-Way Power DB-01Nos in FF]Supply, transportation & installation of 100mm x 50mm x 1.6mm Hot Dipped Galvanized Iron perforated cable trays with cover, including horizontal and vertical bends, reducers tees, cross members and other accessories as required and duly suspended from the ceiling/Wall with suspenders etc., complete. |
| 120 | LT PANELS: |
| 121 | Design, manufacture, supply, installation, testing and commissioning of the following panels designed for 415V, 3Phase, 50Hz, 4wire A.C system made up of sheet steel, dust and vermin proof of Cubicle type, Indoor/Outdoor type, Floor / wall mounting type, free-standing LT distribution panel, design and fabricated with 2mm CRCA sheet steel over heavy MS framing. Upgraded with an Integrated sloped rain canopy roof, Double weatherproof front doors with clear glass inserts.\\", a 400mm vertical cable alley, industrial neoprene seals, and a UV-resistant pure polyester RAL 7032 powder coat finish for main frames, folded sections and load bearing members and 1.6mm CRCA sheet steel for doors & covers and 3mm CRCA sheet steel removable Gland plates at bottom and top entry complete interconnections,Mandate neoprene rubber gendering on all doors to block dust and moisture, internal power and control wiring, cable chamber,busbar chamber, powder coated painting, drawout/hinged and lockable doors with front & back side both doors open access, cable glands, bonding to earth and painting,earthing etc. The following points shall be considered by the Vendor for quoting:-Instruments for Incomers - MCCB,Digital type Multi Function Meter, CTs, control MCB, one set of R,Y,B Indicating Lamps with control MCB and one set of ON/OFF/TRIP indicating lamp with protective MCB Instruments for Outgoings - MCCB,Digital type Multi Function Meter, CTs,control MCB, one set of ON/OFF/TRIP indicating lamp with protective MCB, necessary power and control wiring interconnections All the meters should have RS 485 port with Mod-Bus TCP provisions. All panel shall be provided with potential free contactors for ON/OFF.Busbar shall be of copper and density of busbars shall not exceed 1.24 Amps/ Sq.mm. Busbar of each panel shall be equal rating as incomer. Neutral busbars shall have half the capacity of phase busbars. All outdoor panel shall have IP-65 protection, Hence no extra claim after award of work.Note: All MCCB's sahll be with microprocesser based adjustable thermal-magnetic release having over current protection ,short circuit protection & Earth fault Protection. |
| 122 | MSB (Main Switch Board) POWER PANEL - OUTDOOR TYPE (IP65 Weatherproof)Incoming:-1 No. of 630 Amps, 4 Pole, 50 kA MCCB (Thermal-Magnetic/Microprocessor Trip) with terminal shrouds, phase barriers and all necessary mounting accessories.Outgoingsi) 6 Nos. of 125 Amps, 4 Pole, 36 kA MCCBs (Specify MCCB frame for flush terminal fixing), with all necessary accessories.ii) 2 Nos. of 63 / 100 Amps, 4 Pole, 30 kA MCCBs (Specify MCCB frame for flush terminal fixing), with all necessary accessories.Notes & Integration:- Includes fully insulated Copper Busbar Chamber (sized for 630A continuous rating with safe current density).- Dedicated Terminal Chamber with Cable Trays/Alley.- Internal Terminal Chamber Lighting (LED cubicle lamp with door-limit switch control).- 1 No. Anti-Condensation Space Heater controlled via adjustable Thermostat, including independent MCB/fuse control and protection circuit. |
| 123 | Earth Pits:- (LT Panels-2Nos, Lift-2Nos) |
| 124 | Providing of independent Chemical Earth Pit. The earth electrodes, 50mm dia, wall thickness, 1.8mm, 3 mtr long pure copper pipe, strip in pipe system fitted with 40x6x3100mm pure copper strip from top to bottom, terminal hole of 12mm, pipe filled with conductive crystalline compound, including 2 bags of Earth life compound (25 kgs each) as per IS 3043. with earth inspection chamber of dimensions: Width: 320 mm x 320 mm, Height: 192 mm, Weight: 30 Kgs, Load bearing capacity: 5000 Kgs including drilling of bore in any kind of soil. |
| 125 | Earth Conductors:-( Only for DB's)Supply, installation, testing &commissioning of 8 SWG Copper wire (0.1155Kgs/1Mtr) Earth wire/Strip in horizontal/Vertical run in Ground/Surface/Recess including, revitting, soldering, saddles, making interconnection of earth strip/wire with brass bolt & nuts & washers & solder jointing, painting with two coats of black bituminous paint for earth wire/ strip in ground & green enamel paint for earth wire /strip on surface etc.etc. as required. |
| 126 | Earth Flat:-(Total cable tray)Supply and laying of 25mm x 6mm GI Flat (1.18Kgs/1Mtr) sizes Earth Strip in horizontal /Vertical run in Cable tray/Ground/surface/Recess including, riveting, soldering, saddles, making connection etc as required |
| 127 | Distribution Board(DB's):- |
| 128 | Supply, installation, testing & commissioning of following readymade distribution boards, double door, IP 42 degree protection including interconnections with appropriate capacity size of PVC insulated copper conductor wires (ISI marked),suitable for concealed mounting /wall mounting with MS frame work of 40 x 40 x 5 mm MS angle iron, with M.S. enclosure fabricated out of min 18 SWG /20SWG thick M.S. CRCA sheet as per manufacturers standard, with concealed hinged door, locking arrangement etc. including earthing clamps for both incoming & outgoing circuits, interconnections, per phase isolation kit as required,cable end box & wire way box if required, continuous copper earth wire in the wire way box with single/duplicate brass earthing terminals, danger board, name plate, flexible earthing for the door,metal treatment & powder coated painting, Phase Distribution drawing etc. all as per drawings (G.A. & fabrication drawing to be got approved), etc. relevant IS & instruction of Engineer-in-charge.The powder coating colour shade for DB's shall be as follows:-Note:-1. DB's fed from normal / DG power supply - RAL 7032.2. The DB shall be complete with necessary provision for Four Pole MCB/Isolator/RCCB as Incomer.3. The DB shall be complete with necessary provision for 3nos Double Pole MCB/Isolator/RCCB/RCBOs as sub Incomer.4. MCBs (Type –C) shall be minimum 10 KA /25 KA breaking capacity, as specified.5. Blanking Plates shall be included in scope of work.6. DB shall be of standard readymade type from approved manufacturers as indicated in preferred makes of material.7. Routine tests will be conducted at factory as per relevant IS.8. The DB shall be complete with necessary tinned Copper busbars,interconnections, separate earth bus & separate neutral bus for each phases. 9. All Distribution boards doors are lockable with master sets of key each separate block. |
| 129 | 7 Segment 8-Way DB's;- (Power DB-01No in FF) - Supplying and fixing following 8 way (4 + 24), Double door, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). |
| 130 | 7 Segment 8-Way DB's;- (Power DB-01No FF) - Supplying and fixing Cable End Box (Loose Wire Box) suitable for 8 way, Double door TPN MCB DB, following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. |
| 131 | TPN Double door DB:- (Lift Supply Terrace) - Supplying and fixing of (8 +12) 4 Way TPN Double door DB Horizontal with IP 43, 12 Nos protection suitable for installation of SP outgoing MCBs and for 1 No 4 pole, MCB/Isolator incomer along with provision for 1 No of 4 Pole RCCB/ELCB etc., complete as per IS 8623; IS 13032; IEC 61439-3. |
| 132 | Circuit Breakers:- |
| 133 | Miniature Circuit Breaker(MCB's):-(Lift DB-01No & PDB-01No)Supply, installation, testing & commissioning of Four Pole(4P), 63A rating, 240/415 V, 10kA, \\"C\\" Curve, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections etc, as required. |
| 134 | Miniature Circuit Breaker(MCB's):- (Lift DB-8Nos, PDB-24Nos)Supply, installation, testing & commissioning of Single Pole(1P) 5 A to 32 A rating, 240/415 V, 10kA, \\"C\\" Curve, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections etc, as required. |
| 135 | Residual Current Circuit Breakers with Overload Protection (RCBO):-(Lift DB-01No) - Supply, installation, testing &commissioning of 40A, 4 Pole,300mA RCBO, \\"C\\" Curve for over load, short-circuit and earth leakage protection. Confirms to IEC:61009-1 |
| 136 | Isolator:-(Ground floor PDB I/C cable jointing) - Supplying and fixing 100 Amps rating, four pole, 415 V,isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 137 | Residual Current Circuit Breakers with Overload Protection (RCBO):-(PDB-3Nos FF) - Supply, installation, testing &commissioning of 63A 2 Pole, 100mA RCBO, \\"C\\" Curve for over load, short-circuit and earth leakage protection. Confirms to IEC:61009-1 |
| 138 | Appliances |
| 139 | Water Geysers:-(BMT Rooms)Supply, Transportation and fixing of storage / Pressure type Vertical / Horizontal 230/250V single phase 2000watts ISI mark 5 Star rated water heater with Glass/SS tank and ABS plastic body of 10 Ltrs capacity to withstand up to 6.5 bar of water pressure including all standard accessories and dead weight pressure reducing valve on outlet side, including cost of 2 Nos nylon / PVC / Metallic hose pipe, testing and all labour charges etc., complete. Makes: As per list of recommended brands. |
| 140 | Water Geysers:-(individual room & BMT Rooms)Supply, Transportation and fixing of storage / Pressure type Vertical / Horizontal 230/250V single phase 2000watts ISI mark 5 Star rated water heater with Glass/SS tank and ABS plastic body of 15 Ltrs capacity to withstand up to 6.5 bar of water pressure including all standard accessories and dead weight pressure reducing valve on outlet side, including cost of 2 Nos nylon / PVC / Metallic hose pipe, testing and all labour charges etc., complete. Makes: As per list of recommended brands. |
| 141 | Water Geysers:-(Common Wash Rooms)Supply, Transportation and fixing of storage / Pressure type Vertical / Horizontal 230/250V single phase 2000watts ISI mark 5 Star rated water heater with Glass/SS tank and ABS plastic body of 20 Ltrs capacity to withstand up to 6.5 bar of water pressure including all standard accessories and dead weight pressure reducing valve on outlet side, including cost of 2 Nos nylon / PVC / Metallic hose pipe, testing and all labour charges etc., complete. Makes: As per list of recommended brands. |
| 142 | Induction Stove:- (BMT Isolation Rooms)Supply, installation, testing & commissioning of 2KW Inducation Stove, Single Phase, 230V – 240V AC, 50 Hz,Heavy-duty structural frame fabricated out of food-grade Stainless Steel (SS 304 preferred), IPX4 (splash-proof enclosure sealing) to protect the internal electrical components from liquid spills and boiling overflow. Automatic power cut-off sensor if no cookware is present on the ceramic base plate. Integrated thermistor safety to provide an automatic high-temperature cut-off to prevent fires if a vessel boils dry.Active circuit sensors guarding the induction board components against input over-voltage, under-voltage, and lightning line surges. |
| 143 | Fan Hook:-Supply and fixing of Anchor fastener with fan hook / Providing MS Fan hook (with double anchor fastners) with grouting and cement plastering. |
| 144 | Fan Regulator:- Supplying and fixing one module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 145 | Exhuast Fan:- Supply of 12\\" (300mm) ISI, 900 RPM Heavy duty exhaust fan with metallic blades with mark. |
| 146 | Exhuast Fan:-Supply of 18\\" (450mm) ISI, 900 RPM Heavy duty exhaust fan with metallic blades with ISI Mark. |
| 147 | Installation, Testing and Commissioning of 12\\" (300mm) ISI, 900 RPM Heavy duty exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 148 | LED Light Fixtures & Fittings:-Supply, installation testing & commissioning of LED fixtures & fittings complete with accessories, tube/lamp etc. in on surface of slab/beam by 2 no's (minimum) of 6 mm anchor fasteners or on wall with 2 no's of wood screws. nylon plug etc., suitable supporting frame fixed with rag bolts grouted on the wall/anchor fastener on the beam/on the column & other fixing accessories etc. provision & connection with 2.5 Sqmm multi stranded copper conductor FRLS PVC wires etc. all as per drawing, specifications & as per the instruction of E.I.C.Note:1. Sample fixture/fittings shall be got approved from Dept with complete technical data.2. The LED fixtures shall be with inbuilt drivers unless mentioned otherwise in SOQ.3. The LED luminaires shall be offered for routine & acceptance testing as per IS at OEM works, prior to material dispatch.4. The scope includes all necessary connected accessories, supporting bracket /rope suspender, suspension conduit, connectors, terminal, flexible wire with GI flexible hose & gland from light point to lighting luminaires etc. complete as required without any extra cost. |
| 149 | Supplying, installation, Testing & Commissioning of 40 Watt LED Batten light (System lumen efficacy >135 lm/Watt) LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85% ,Operating voltage AC 140 270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)/ 40 Watt Rechargeable LED Tubelight as directed by EIC. |
| 150 | Supplying, installation, Testing & Commissioning of 18Watt LED Slim Panel Round /Square suitable for Recessed / Surface mounting made of diecast aluminum body with powder coating, acrylic diffuser with driver as per IS: 15885 (Part 2/ Sec 13) : 2012, operating voltage range of 150 to 265 Volts AC, P.F > 0.9, Surge protection: 2KV, THD<10%, with high power LEDs, having System Efficacy of >=100 lumens /watt, CCT: 3000K - 5700K, minimum CRI>70, Luminaire performance complies to IS 10322 (Part 5 / Sec-2) .etc., complete with earth connection and not less than two years warranty. |
| 151 | 10W LED Light:- (Lift Shaft-4Nos & Rooms Foot Light-17Nos)Supplying, installation, Testing & Commissioning of 10W LED Bulkhead Light fitting/Foot Lights with Pressure die cast aluminum with opal diffuser with IP 65 protection etc.,complete. |
| 152 | Supplying, Installation, Testing & Commissioning of 150 Watts LED Flood Light, powder coated pressure die cast aluminium (System lumen efficacy >135 lm/Watt), powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle 30 deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin) ,SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). |
| 153 | Point and Submain Wiring:- |
| 154 | Supply, installation, testing & commissioning of Point wiring in PVC conduit (HMS variety)/GI conduit : Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed steel conduit as required. Point wiring for light/ceiling fan/6A/16A outlet for exhaust fan, bell point etc, with 1.1KV grade FRLS PVC insulated multistrand copper conductor wire (ISI marked), in GI conduit on surface / 25 to 40 mm dia High mechanical stress (HMS) rigid concealed in Wall/Beam/Slab/Column PVC conduit having ISI marked IS 9537 Part - 3, including fixing accessories & hardware. The GI conduits shall be mounted on 5mm. thick G.I. spacers fixed with no.10 nettle fold wood screws with nylon plug complete with all conduit accessories 20 SRG G.I. Saddles. The scope shall include providing ready made MS switchboxes, socket outlet boxes of min 18 SWG / 20 SWG thickness. brass earthing stud 1/2 no's controlling modular switches, sockets with moulded front plate appropriate size of FRLS PVC insulated copper earth wire brass/Bakelite (Straight / Angular) lamp holders, 3 plate ceiling rose, 16 A, connectors, painting etc. as per specifications and drawings and as per instructions of E-I-C and as detailed below: (Sample switch box etc. to be got approved before fabrication)NOTE:1. Connections shall be done with crimped type tinned copper lugs & washers.2. All switches & Socket outlets shall be as per preferred makes.3. All sample boxes with accessories / fixtures shall be got approved from Department.4. All 16A socket outlets should be with 6 pin & shuttered type.5. MS boxes other than switch boxes & socket outlet boxes shall be fabricated out of 16 SWG thickness MS sheet duly painted with red oxide primer & 2 coats of epoxy paint.6. Minimum size of the FRLS insulated copper earth wire continuity shall be 2.5 Sq.mm7. The colour shade of switches shall be white / off white. For socket outlet points / switch boards on normal power / DG supply, the cover plate shall be white/ off white colour & Graphite grey (RAL 7024) for socket outlet points/ switch boards on UPS power supply.8. The scope also includes supply of modular blanking plates where ever required.9. The maximum permissible number of PVC insulated wire through PVC conduits shall be as per technical specifications and relevant IS codes.10. The point wiring shall generally be concealed type only, except in lift shaft/ Elect. Shaft/basement areas/ in RCC retaining wall/ in dry well/ above false ceiling & wherever concealed wiring is not feasible, as per instructions of E.I.C.11. All light/ ceiling fan/exhaust fan/power receptacles point wiring shall include the cost of circuit mains with suitable HMS PVC pipe for concealed system & GI pipe for surface installation. No extra payment will be made for the same.12. All embeded conduit junction boxes/pull boxes shall be covered by 18 SWG thick M S sheet covers painted white projecting at least 5 mm around finished opening fixed to box with CSK machine screws. |
| 155 | Submain Wiring(2.5 Sqmm):- (Lighting Switch Boards -42Nos)Wiring for circuit/ submain wiring for 2 X 2.5 sq. mm + 1 X 2.5 sq. mm sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed HMS(Heavy Mechanical Stress )PVC conduit as required. |
| 156 | Submain Wiring(4 Sqmm):- (General Socket Switch Boards -20Nos)Wiring for circuit/ submain wiring for 2 X 4 sq. mm + 1 X 4 sq. mm sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed HMS(Heavy Mechanical Stress )PVC conduit as required. |
| 157 | Point Wiring:- Light \\"A-Point\\"Wiring for light point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed High Mechanical Strength (HMS) PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 158 | Point Wiring:- Light \\"C-Point\\"Wiring for light point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed High Mechanical Strength (HMS) PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 159 | Point Wiring:- Ceiling Fan \\"C-Point\\"Wiring for Ceiling Fan point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed High Mechanical Strength (HMS) PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 160 | Point Wiring:- Exhaust Fan \\"C-Point\\"Wiring for Exhaust fan point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed High Mechanical Strength (HMS) PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 161 | Modular Sockets:- (Stove-4Nos, Lift-04Nos & Geyser-16Nos FF)Supplying and fixing of 6 pin 15/16 A socket outlet 2-Modular on the existing modular plate & switch box including connections but excluding modular plate etc. as required |
| 162 | Modular Switchs:- (Stove-4Nos, Lift-04Nos & Geyser-16Nos FF)Supplying and fixing of 15/16 A Switch 1-Modular, 1-Way with Indication Lamp on the existing modular plate & switch box including connections but excluding modular plate etc. as required |
| 163 | Ceiling Rose:-Supplying and fixing 3 pin, 5 A Ceiling Rose on the existing junction box/ wooden block including connections etc. as required. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysNov 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender