Tender For General-Renovation Works At District Treasury Strong Room-Renovation Works At District Treasury Strong Room Inside Thrissur Collectorate, Civil Lane, Ayyanthole, Thrissur-General Civil Work
Tender Value
10.82 Lakhs
Estimated cost
Bid Submission
07 Nov 2026
6 days left
EMD
27064
Bank guarantee accepted
Document Fee
2760
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thrissur → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for General-Renovation Works At District Treasury Strong Room-Renovation Works At District Treasury Strong Room Inside Thrissur Collectorate, Civil Lane, Ayyanthole, Thrissur-General Civil Work
BOQ
| Sl. No. | Item Description |
| 1 | Estimate |
| 2 | 15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar |
| 3 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 4 | 13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer |
| 5 | 13.83.2:Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour.Two coats |
| 6 | OD174890/2025-2026:Supply , Installation, Testing and Commissioning of Vault door of the following specifications:1. The Vault (Strong Room) Door (Main Door) dimensions and specification shall be strictly adhering to IS 11188 (Part-1): 20142. The Door shall have BIS Label of Class B having Torch & Tool Resisting capacity for minimum 30 minutes and Fire Resisting Capacity for minimum 30 minutes.3. The bidder/OEM must possess Valid BIS License to manufacture and supply the aforementioned TRTL Door (Class B)4. All the surfaces of the Door before painting shall be thoroughly degreased and cleaned of rust and scales preferably by 12 tank pickling process and treated chemically to prevent from rusting.5. The Door shall be painted inside and outside with an anti-corrosive primer followed by two undercoats of paints and finally painted with quick drying paint, resulting into minimum 300 hrs of salt spray resistance. (Attach certificate/declaration)6. The main door (Class B) shall consist of outer and inner mild steel plates conforming to IS 2062:1992 for plates up to 20 mm thick strongly rimmed and continuously welded to form a single structure and tightly enclosing a solid slab of high speed drill resisting and oxy acetylene torch resisting material that is at least 50 mm thick7. Door Frame: The door frame and vestibule shall be welded to one piece construction with a minimum thickness of 10 mm and shall grip the concrete wall.8. Rebate: The rebate of the door frame shall be formed by mild steel sections. The vertical rebates shall be riveted or welded with the side members of the door frame and shall conform to dimensions as specified by IS 11188.9. Clenching mechanism: A continuous resilient packing shall be incorporated in the frame and a compression mechanism for clenching the door tight shall be provided so as to protect against admission of flood water or liquid explosives. In locked position the door after clenching shall not have any play in the direction in which the door opens.10. Thickness of door over locks: Should be of minimum 90mm thickness.11. The Door shall have an automatic relocking device for each Key lock fitted in the door which being always on guard shall come into operation if lock is dislodged by explosives or by other means.12. Primary lock of the door shall have additional relocking device which being always on guard shall come into operation if lock is dislodged by explosive or any other means.13. The lock shall be dual control type and have at least 8 active levers of brass of minimum 1.2 mm thickness. There should not be any dummy (false) levers.14. The bidder/OEM must be the Original Equipment Manufacturer of the Locks used in the aforementioned Safe. (OEM must give a written undertaking on Letterhead and must also give an NOC to the bank for plant visit if needed)15. Lock Case: Should be minimum 2 step case construction covering entire jamb area.16. The lock shall be fixed with at least four bolts of 8 mm diameter such that any pressure applied on the bolts either directly or through handle of the door, is not transmitted to the fixing screw of the lock/locks. All working parts of the lock shall have corrosion resistant properties capable of withstanding exposure for 72 h in standard salt spray test with 5 percent salt solution.17. Bolt Work: There shall be 6 locking bolts each on the vertical edges of the door(Front edge & Rear edge).18. Hinges: Strap hinges to be suitably bolted to the door shutter. The hinge and pivot should be such that there is no appreciable friction or play for the movement of the door. The pivots shall have arrangements for lubrication and a height adjustment bolt is to be provided to adjust height of door shutter19. Grill Gate (Inside) : Ventilating Grill Gate shall be made of mild steel angles, plates or channels with mild steel rods welded in a rigid frame. The grill gate shall be hinged in strong room door frame such that it opens inside. An unpickable dual control locking device capable of being operated from both the sides of the door shall be fitted in the grill gate.20. Emergency Door: The general specifications of Emergency Door shall remain as for the main door except for Bolt Work. For Bolt Work, there shall be 3 locking bolts each on the vertical edges of the emergency door (Front edge & Rear edge).21. LIMIT SWITCH/LIGHTING CONTROL: Vault lighting control shall be fitted on the Main Door to automatically control the electric supply to the vault. |
| 7 | 13.99.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work |
| 8 | 13.62.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture . |
| 9 | 11.41A.1.3: Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of sizeSize of Tile 600 x 1200 mm |
| 10 | 50.5.4:Providing and laying up to floor five level reinforced cement concrete in kerbs, steps and the like excluding the cost of centering, shuttering, finishing and reinforcement with 1:1. 5:3 ( 1 cement :1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size |
| 11 | 50.6.1.6:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete |
| 12 | 5.22A.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more |
| 13 | 5.9.16.1:Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide |
| 14 | 5.9.4:Centering and shuttering including strutting, etc. and removal of form for:Shelves (Cast in situ) |
| 15 | 13.16.1:6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysNov 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender